If PTP synchronisation is done every second, then sporadic the interval
is higher than one second:
ptp4l[696.582]: master offset -17 s2 freq -1891 path delay 573
ptp4l[697.582]: master offset -22 s2 freq -1901 path delay 573
ptp4l[699.368]: master offset -1 s2 freq -1887 path delay 573
^^^^^^^ Should be 698.582!
This problem is caused by rotten packets, which are received after
polling but before interrupts are enabled again. This can be fixed by
checking for pending work and rescheduling if necessary after interrupts
has been enabled again.
Fixes: 403f69bbdb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20221119211825.81805-1-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 4581dd480c ("net: octeontx2-pf: mcs: consider MACSEC setting")
has already added "depends on MACSEC || !MACSEC", so remove it.
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221119133616.3583538-1-zhengbin13@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.
Fixes: b56e9670ff ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In commit f11fe1dae1 ("net/sched: Make NET_ACT_CT depends on NF_NAT"),
it fixed the build failure when NF_NAT is m and NET_ACT_CT is y by
adding depends on NF_NAT for NET_ACT_CT. However, it would also cause
NET_ACT_CT cannot be built without NF_NAT, which is not expected. This
patch fixes it by changing to use "(!NF_NAT || NF_NAT)" as the depend.
Fixes: f11fe1dae1 ("net/sched: Make NET_ACT_CT depends on NF_NAT")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b6386f28d1ba34721795fb776a91cbdabb203447.1668807183.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If phylink_of_phy_connect() fails, the port should be disabled.
If sparx5_serdes_set()/phy_power_on() fails, the port should be
disabled and the phylink should be stopped and disconnected.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Fixes: f3cad2611a ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Tested-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221117125918.203997-1-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
acpi_evaluate_dsm() should be coupled with ACPI_FREE() to free the ACPI
memory, because we need to track the allocation of acpi_object when
ACPI_DBG_TRACK_ALLOCATIONS enabled, so use ACPI_FREE() instead of kfree().
Fixes: d38a648d2d ("net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221118062447.2324881-1-bobo.shaobowang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 1229b33973 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.
This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.
ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.
This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.
This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.
If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.
Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.
The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.
Fix the function to appropriately return true when the tracker is not
initialized.
Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b33973 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If skb_linearize() fails in tipc_disc_rcv(), we need to free the skb instead of
handle it.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20221119072832.7896-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-11-18 (iavf)
Ivan Vecera resolves issues related to reset by adding back call to
netif_tx_stop_all_queues() and adding calls to dev_close() to ensure
device is properly closed during reset.
Stefan Assmann removes waiting for setting of MAC address as this breaks
ARP.
Slawomir adds setting of __IAVF_IN_REMOVE_TASK bit to prevent deadlock
between remove and shutdown.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix race condition between iavf_shutdown and iavf_remove
iavf: remove INITIAL_MAC_SET to allow gARP to work properly
iavf: Do not restart Tx queues after reset task failure
iavf: Fix a crash during reset task
====================
Link: https://lore.kernel.org/r/20221118222439.1565245-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long says:
====================
tipc: fix two race issues in tipc_conn_alloc
The race exists beteen tipc_topsrv_accept() and tipc_conn_close(),
one is allocating the con while the other is freeing it and there
is no proper lock protecting it. Therefore, a null-pointer-defer
and a use-after-free may be triggered, see details on each patch.
====================
Link: https://lore.kernel.org/r/cover.1668807842.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One extra conn_get() is needed in tipc_conn_alloc(), as after
tipc_conn_alloc() is called, tipc_conn_close() may free this
con before deferencing it in tipc_topsrv_accept():
tipc_conn_alloc();
newsk = newsock->sk;
<---- tipc_conn_close();
write_lock_bh(&sk->sk_callback_lock);
newsk->sk_data_ready = tipc_conn_data_ready;
Then an uaf issue can be triggered:
BUG: KASAN: use-after-free in tipc_topsrv_accept+0x1e7/0x370 [tipc]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x178/0x4b0
kasan_report+0x8c/0x100
kasan_check_range+0x179/0x1e0
tipc_topsrv_accept+0x1e7/0x370 [tipc]
process_one_work+0x6a3/0x1030
worker_thread+0x8a/0xdf0
This patch fixes it by holding it in tipc_conn_alloc(), then after
all accessing in tipc_topsrv_accept() releasing it. Note when does
this in tipc_topsrv_kern_subscr(), as tipc_conn_rcv_sub() returns
0 or -1 only, we don't need to check for "> 0".
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A crash was reported by Wei Chen:
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:tipc_conn_close+0x12/0x100
Call Trace:
tipc_topsrv_exit_net+0x139/0x320
ops_exit_list.isra.9+0x49/0x80
cleanup_net+0x31a/0x540
process_one_work+0x3fa/0x9f0
worker_thread+0x42/0x5c0
It was caused by !con->sock in tipc_conn_close(). In tipc_topsrv_accept(),
con is allocated in conn_idr then its sock is set:
con = tipc_conn_alloc();
... <----[1]
con->sock = newsock;
If tipc_conn_close() is called in anytime of [1], the null-pointer-def
is triggered by con->sock->sk due to con->sock is not yet set.
This patch fixes it by moving the con->sock setting to tipc_conn_alloc()
under s->idr_lock. So that con->sock can never be NULL when getting the
con from s->conn_idr. It will be also safer to move con->server and flag
CF_CONNECTED setting under s->idr_lock, as they should all be set before
tipc_conn_alloc() is called.
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the ccr read error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3265f42188 ("net: phy: at803x: add fiber support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221118103635.254256-1-weiyongjun@huaweicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This code accidentally uses the RX macro twice instead of the RX and TX.
Fixes: 6c635f78c4 ("octeontx2-af: cn10k: mcs: Handle MCS block interrupts")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.
Replace zero-length array with flexible-array member in struct key_vector.
This results in no differences in binary output.
[1] https://github.com/KSPP/linux/issues/78
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:
# TEST: vti4: PMTU exceptions [SKIP]
[ 350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm6udp not supported
# TEST: vti6: PMTU exceptions (ESP-in-UDP) [SKIP]
[ 351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm4udp not supported
The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:
The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.
[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains late Netfilter fixes for net:
1) Use READ_ONCE()/WRITE_ONCE() to update ct->mark, from Daniel Xu.
Not reported by syzbot, but I presume KASAN would trigger post
a splat on this. This is a rather old issue, predating git history.
2) Do not set up extensions for set element with end interval flag
set on. This leads to bogusly skipping this elements as expired
when listing the set/map to userspace as well as increasing
memory consumpton when stateful expressions are used. This issue
has been present since 4.18, when timeout support for rbtree set
was added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Function sparx5_tc_setup_qdisc_ets() always returns negative value
because it return -EOPNOTSUPP in the end. This patch returns the
rersult of sparx5_tc_ets_add() and sparx5_tc_ets_del() directly.
Fixes: 211225428d ("net: microchip: sparx5: add support for offloading ets qdisc")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shang XiaoJing says:
====================
nfc: Fix potential memory leak of skb
There are still somewhere maybe leak the skb, fix the memleaks by adding
fail path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
s3fwrn5_nci_send() won't free the skb when it failed for the check
before s3fwrn5_write(). As the result, the skb will memleak. Free the
skb when the check failed.
Fixes: c04c674fad ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
nxp_nci_send() won't free the skb when it failed for the check before
write(). As the result, the skb will memleak. Free the skb when the
check failed.
Fixes: dece45855a ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
won't free the skb when it failed for the test_bit(). Free the skb when
test_bit() failed.
Fixes: b5b3e23e4c ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ret' is defined twice in macsec_changelink(), when it is set in macsec_is_offloaded
case, it will be invalid before return.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20221118011249.48112-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, we get icmp6hdr via function icmp6_hdr(), which needs the skb
transport header to be set first. But there is no rule to ask driver set
transport header before netif_receive_skb() and bond_handle_frame(). So
we will not able to get correct icmp6hdr on some drivers.
Fix this by using skb_header_pointer to get the IPv6 and ICMPV6 headers.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 4e24be018e ("bonding: add new parameter ns_targets")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20221118034353.1736727-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman says:
====================
nfp: fixes for v6.1
- Ensure that information displayed by "devlink port show"
reflects the number of lanes available to be split.
- Avoid NULL dereference in ethtool test code.
====================
Link: https://lore.kernel.org/r/20221117153744.688595-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setting of the port flag `NFP_PORT_CHANGED`, introduced
to ensure the correct reading of EEPROM data, causes a
fatal kernel NULL pointer dereference in cases where
the target netdev type cannot be determined.
Add validation of port struct pointer before attempting
to set the `NFP_PORT_CHANGED` flag. Return that operation
is not supported if the netdev type cannot be determined.
Fixes: 4ae97cae07 ("nfp: ethtool: fix the display error of `ethtool -m DEVNAME`")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The error is reflected in that it shows wrong splittable status of
port when executing "devlink port show".
The reason which leads the error is that the assigned operation of
splittable is just a simple negation operation of split and it does
not consider port lanes quantity. A splittable port should have
several lanes that can be split(lanes quantity > 1).
If without the judgement, it will show wrong message for some
firmware, such as 2x25G, 2x10G.
Fixes: a0f49b5486 ("devlink: Add a new devlink port split ability attribute and pass to netlink")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
In pch_gbe_probe(), pci_get_domain_bus_and_slot() is called,
so in error path in probe() and remove() function, pci_dev_put()
should be called to avoid refcount leak. Compile tested only.
Fixes: 1a0bdadb4e ("net/pch_gbe: supports eg20t ptp clock")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117135148.301014-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from rvu_dbg_rvu_pf_cgx_map_display() or
cgx_print_dmac_flt(), pci_dev_put() is called to avoid refcount
leak.
Fixes: dbc52debf9 ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: e2fb373038 ("octeontx2-af: Display CGX, NIX and PF map in debugfs.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117124658.162409-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ql3xxx_send() returns NETDEV_TX_OK without freeing skb in error
handling case, add dev_kfree_skb_any() to fix it.
Fixes: bd36b0ac5d ("qla3xxx: Add support for Qlogic 4032 chip.")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1668675039-21138-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It will cause invalid pointer dereference to priv->cm3_base behind,
if PTR_ERR(priv->cm3_base) in mvpp2_get_sram().
Fixes: e54ad1e01c ("net: mvpp2: add CM3 SRAM memory map")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Link: https://lore.kernel.org/r/20221117084032.101144-1-tanghui20@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If mlx4_bitmap_init fails, mlx4_bitmap_alloc_range will dereference
the NULL pointer (bitmap->table).
Make sure, that mlx4_bitmap_alloc_range called in no error case.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d57febe1a4 ("net/mlx4: Add A0 hybrid steering")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Peter Kosyh <pkosyh@yandex.ru>
Link: https://lore.kernel.org/r/20221117152806.278072-1-pkosyh@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If mtk_start_dma() fails, invoke phylink_disconnect_phy() to perform
cleanup. phylink_disconnect_phy() contains the put_device action. If
phylink_disconnect_phy is not performed, the Kref of netdev will leak.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221117111356.161547-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a deadlock introduced by commit
974578017f ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.
Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IAVF_FLAG_INITIAL_MAC_SET prevents waiting on iavf_is_mac_set_handled()
the first time the MAC is set. This breaks gratuitous ARP because the
MAC address has not been updated yet when the gARP packet is sent out.
Current behaviour:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: ee:04:19:14:ec:ea
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:23:41.676611 ee:04:19:14:ec:ea > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
With IAVF_FLAG_INITIAL_MAC_SET removed:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: 3e:8a:16:a2:37:6d
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:28:01.836608 00:11:22:33:44:55 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
Fixes: 35a2443d09 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Elements with an end interval flag set on do not store extensions. The
global set definition is currently setting on the timeout and stateful
expression for end interval elements.
This leads to skipping end interval elements from the set->ops->walk()
path as the expired check bogusly reports true.
Moreover, do not set up stateful expressions for elements with end
interval flag set on since this is never used.
Fixes: 65038428b2 ("netfilter: nf_tables: allow to specify stateful expression in set definition")
Fixes: 8d8540c4f5 ("netfilter: nft_set_rbtree: add timeout support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conn:mark can be read from and written to in parallel. Use
READ_ONCE()/WRITE_ONCE() for reads and writes to prevent unwanted
compiler optimizations.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.
Fixes: 77555ee722 ("net: Add Gigabit Ethernet driver of Topcliff PCH")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we leverage NCI_UNREG and the lock inside nci_close_device to
prevent the race condition between opening a device and closing a
device. However, it still has problem because a failed opening command
will erase the NCI_UNREG flag and allow another opening command to
bypass the status checking.
This fix corrects that by making sure the NCI_UNREG is held.
Reported-by: syzbot+43475bf3cfbd6e41f5b7@syzkaller.appspotmail.com
Fixes: 48b71a9e66 ("NFC: add NCI_UNREG flag to eliminate the race")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rxrpc_unbundle_conn() has removed a connection from a bundle, it
checks to see if there are any conns with available channels and, if not,
removes and attempts to destroy the bundle.
Whilst it does check after grabbing client_bundles_lock that there are no
connections attached, this races with rxrpc_look_up_bundle() retrieving the
bundle, but not attaching a connection for the connection to be attached
later.
There is therefore a window in which the bundle can get destroyed before we
manage to attach a new connection to it.
Fix this by adding an "active" counter to struct rxrpc_bundle:
(1) rxrpc_connect_call() obtains an active count by prepping/looking up a
bundle and ditches it before returning.
(2) If, during rxrpc_connect_call(), a connection is added to the bundle,
this obtains an active count, which is held until the connection is
discarded.
(3) rxrpc_deactivate_bundle() is created to drop an active count on a
bundle and destroy it when the active count reaches 0. The active
count is checked inside client_bundles_lock() to prevent a race with
rxrpc_look_up_bundle().
(4) rxrpc_unbundle_conn() then calls rxrpc_deactivate_bundle().
Fixes: 245500d853 ("rxrpc: Rewrite the client connection manager")
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-15975
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: zdi-disclosures@trendmicro.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit afef88e655 ("selftests/bpf: Store BPF object files with
.bpf.o extension"), we should use xdp_dummy.bpf.o instade of xdp_dummy.o.
In addition, use the BPF_FILE variable to save the BPF object file name,
which can be better identified and modified.
Fixes: afef88e655 ("selftests/bpf: Store BPF object files with .bpf.o extension")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Cc: Daniel Müller <deso@posteo.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently syzkaller discovered the issue of disappearing lower
device (NETDEV_UNREGISTER) while the virtual device (like
macvlan) is still having it as a lower device. So it's just
a matter of time similar discovery will be made for IPvlan
device setup. So fixing it preemptively. Also while at it,
add a refcount tracker.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ff4eb3d5e ("neighbour: make proxy_queue.qlen limit
per-device") introduced the length counter qlen in struct neigh_parms.
There are separate neigh_parms instances for IPv4/ARP and IPv6/ND, and
while the family specific qlen is incremented in pneigh_enqueue(), the
mentioned commit decrements always the IPv4/ARP specific qlen,
regardless of the currently processed family, in pneigh_queue_purge()
and neigh_proxy_process().
As a result, with IPv6/ND, the family specific qlen is only incremented
(and never decremented) until it exceeds PROXY_QLEN, and then, according
to the check in pneigh_enqueue(), neighbor solicitations are not
answered anymore. As an example, this is noted when using the
subnet-router anycast address to access a Linux router. After a certain
amount of time (in the observed case, qlen exceeded PROXY_QLEN after two
days), the Linux router stops answering neighbor solicitations for its
subnet-router anycast address and effectively becomes unreachable.
Another result with IPv6/ND is that the IPv4/ARP specific qlen is
decremented more often than incremented. This leads to negative qlen
values, as a signed integer has been used for the length counter qlen,
and potentially to an integer overflow.
Fix this by introducing the helper function neigh_parms_qlen_dec(),
which decrements the family specific qlen. Thereby, make use of the
existing helper function neigh_get_dev_parms_rcu(), whose definition
therefore needs to be placed earlier in neighbour.c. Take the family
member from struct neigh_table to determine the currently processed
family and appropriately call neigh_parms_qlen_dec() from
pneigh_queue_purge() and neigh_proxy_process().
Additionally, use an unsigned integer for the length counter qlen.
Fixes: 0ff4eb3d5e ("neighbour: make proxy_queue.qlen limit per-device")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the warning reported by kbuild:
cocci warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/cavium/liquidio/lio_main.c:1797:54-56: WARNING !A || A && B is equivalent to !A || B
drivers/net/ethernet/cavium/liquidio/lio_main.c:1827:54-56: WARNING !A || A && B is equivalent to !A || B
Fixes: 8979f428a4 ("net: liquidio: release resources when liquidio driver open failed")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: selftests: Fix timeouts and test isolation
Patches 1 and 3 adjust test timeouts to reduce false negatives on slow
machines.
Patch 2 improves test isolation by running the mptcp_sockopt test in its
own net namespace.
====================
Link: https://lore.kernel.org/r/20221115221046.20370-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
