It seems these chip versions never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With newer chip versions ASPM-related issues seem to occur only if
L1.2 is enabled. I have a test system with RTL8168h that gives a
number of rx_missed errors when running iperf and L1.2 is enabled.
With L1.2 disabled (and L1 + L1.1 active) everything is fine.
See also [0]. Can't test this, but L1 + L1.1 being active should be
sufficient to reach higher package power saving states.
[0] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1942830
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/36feb8c4-a0b6-422a-899c-e61f2e869dfe@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
include/linux/netdevice.h became too big, move gro stuff
into include/net/gro.h
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several cases where validate() would return bogus supported
modes with unusual combinations of interfaces and capabilities. For
example, if state->interface was 10GBASER and the macb had HIGH_SPEED
and PCS but not GIGABIT MODE, then 10/100 modes would be set anyway. In
another case, SGMII could be enabled even if the mac was not a GEM
(despite this being checked for later on in mac_config()). These
inconsistencies make it difficult to refactor this function cleanly.
There is still the open question of what exactly the requirements for
SGMII and 10GBASER are, and what SGMII actually supports. If someone
from Cadence (or anyone else with access to the GEM/MACB datasheet)
could comment on this, it would be greatly appreciated. In particular,
what is supported by Cadence vs. vendor extension/limitation?
To address this, the current logic is split into three parts. First, we
determine what we support, then we eliminate unsupported interfaces, and
finally we set the appropriate link modes. There is still some cruft
related to NA, but this can be removed in a future patch.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Parshuram Thombare <pthombar@cadence.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211112190400.1937855-1-sean.anderson@seco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert mvpp2 to use phylink_generic_validate() for the bulk of its
validate() implementation. This network adapter has a restriction
that for 802.3z links, autonegotiation must be enabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mvneta to use phylink_generic_validate() for the bulk of its
validate() implementation. This network adapter has a restriction
that for 802.3z links, autonegotiation must be enabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARRAY_SIZE defined in <linux/kernel.h> is safer than self-defined
macros to get size of an array such as ARRAY_LEN used here. Because
ARRAY_SIZE uses __must_be_array(arr) to ensure arr is really an array.
Reported-by: Alejandro Colomar <colomar.6.4.3@gmail.com>
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous stmmac_xdp_set_prog() implementation uses stmmac_release()
and stmmac_open() which tear down the PHY device and causes undesirable
autonegotiation which causes a delay whenever AFXDP ZC is setup.
This patch introduces two new functions that just sufficiently tear
down DMA descriptors, buffer, NAPI process, and IRQs and reestablish
them accordingly in both stmmac_xdp_release() and stammac_xdp_open().
As the results of this enhancement, we get rid of transient state
introduced by the link auto-negotiation:
$ ./xdpsock -i eth0 -t -z
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 634444 634560
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632330 1267072
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632438 1899584
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632502 2532160
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different
from the tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit operations
to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries
to access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmGNQdwACgkQMUZtbf5S
IrsiMQ//f66lTJ8PJ5Qj70hX9dC897olx7uGHB9eiKoyOcJI459hFlfXwRU2T4Tf
fPNwPNUQ9Mynw9tX/jWEi+7zd6r6TSHGXK49U9/rIbQ95QjKY4LHowIE63x+vPl2
5Cpf+80zXC3DUX1fijgyG1ujnU3kBaqopTxDLmlsHw2PGkwT5Ox1DUwkhc370eEL
xlpq3PYGWA8/AQNyhSVBkG/UmoLaq0jYNP5yVcOj4jGjgcgLe1SLrqczENr35QHZ
cRkuBsFBMBZF7wSX2f9qQIB/+b1pcLlD9IO+K3S7Ruq+rUd7qfL/tmwNxEh0axYK
AyIun1Bxcy7QJGjtpGAz+Ku7jS9T3HxzyxhqilQo3co8jAW0WJ1YwHl+XPgQXyjV
DLG6Vxt4syiwsoSXGn8MQugs4nlBT+0qWl8YamIR+o7KkAYPc2QWkXlzEDfNeIW8
JNCZA3sy7VGi1ytorZGx16sQsEWnyRG9a6/WV20Dr+HVs1SKPcFzIfG6mVngR07T
mQMHnbAF6Z5d8VTcPQfMxd7UH48s1bHtk5lcSTa3j0Cw+GkA6ytTmjPdJ1qRcdkH
dl9jAfADe4O6frG+9XH7FEFqhmkghVI7bOCA4ZOhClVaIcDGgEZc2y7sY9/oZ7P4
KXBD2R5X1caCUM0UtzwL7/8ddOtPtHIrFnhY+7+I6ijt9qmI0BY=
=Ttgq
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different from the
tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the
workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit
operations to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs"
* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
selftests/net: udpgso_bench_rx: fix port argument
net: wwan: iosm: fix compilation warning
cxgb4: fix eeprom len when diagnostics not implemented
net: fix premature exit from NAPI state polling in napi_disable()
net/smc: fix sk_refcnt underflow on linkdown and fallback
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
gve: fix unmatched u64_stats_update_end()
net: ethernet: lantiq_etop: Fix compilation error
selftests: forwarding: Fix packet matching in mirroring selftests
vsock: prevent unnecessary refcnt inc for nonblocking connect
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
net: stmmac: allow a tc-taprio base-time of zero
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
net: hns3: allow configure ETS bandwidth of all TCs
net: hns3: remove check VF uc mac exist when set by PF
net: hns3: fix some mac statistics is always 0 in device version V2
net: hns3: fix kernel crash when unload VF while it is being reset
net: hns3: sync rx ring head in echo common pull
net: hns3: fix pfc packet number incorrect after querying pfc parameters
...
Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.
Fixes: f56ec6766d ("cxgb4: Add support for ethtool i2c dump")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a minus character missing from ERR_PTR(ENOMEM) so if this
allocation fails it will lead to an Oops in the caller.
Fixes: dc48516ec7 ("net/mlx5: Lag, add support to create definers for LAG")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64_stats_update_end() call is supposed to be inside the curly
braces so it pairs with the u64_stats_update_begin().
Fixes: 37149e9374 ("gve: Implement packet continuation for RX.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the error detected when compiling the driver.
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe301ebbc ("net: mvpp2: convert to use
mac_prepare()/mac_finish()") introduced a bug wherein it leaves the MAC
RESET register asserted after mac_finish(), due to wrong order of
function calls.
Before it was:
.mac_config()
mvpp22_mode_reconfigure()
assert reset
mvpp2_xlg_config()
deassert reset
Now it is:
.mac_prepare()
.mac_config()
mvpp2_xlg_config()
deassert reset
.mac_finish()
mvpp2_xlg_config()
assert reset
Obviously this is wrong.
This bug is triggered when phylink tries to change the PHY interface
mode from a GMAC mode (sgmii, 1000base-x, 2500base-x) to XLG mode
(10gbase-r, xaui). The XLG mode does not work since reset is left
asserted. Only after
ifconfig down && ifconfig up
is called will the XLG mode work.
Move the call to mvpp22_mode_reconfigure() to .mac_prepare()
implementation. Since some of the subsequent functions need to know
whether the interface is being changed, we unfortunately also need to
pass around the new interface mode before setting port->phy_interface.
Fixes: bfe301ebbc ("net: mvpp2: convert to use mac_prepare()/mac_finish()")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is spurious to allocate a bitmap without initializing it.
So, better safe than sorry, initialize it to 0 at least to have some known
values.
While at it, switch to the devm_bitmap_ API which is less verbose.
Fixes: 4b41d34367 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe28c53ed7 ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes: 330baff542 ("net: hns3: add ETS TC weight setting in SSU module")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If users set unicast mac address for VFs by PF, they need to guarantee all
VFs' address is different. This patch removes the check mac address exist
of VFs, for usrs can refresh mac addresses of all VFs directly without
need to modify the exist mac address to other value firstly.
Fixes: 8e6de441b8 ("net: hns3: add support for configuring VF MAC from the host")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver queries the register number of mac statistics from firmware,
the old firmware runs in device version V2 only returns number of valid
registers, not include number of three reserved registers among of them.
It cause driver doesn't record the last three data when query mac
statistics.
To fix this problem, driver never query register number in device version
V2 and set it to a fixed value which include three reserved registers.
Fixes: c8af2887c9 ("net: hns3: add support pause/pfc durations for mac statistics")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver processes rx packets, the head pointer is updated only
after the number of received packets reaches 16. However, hardware
relies on the head pointer to calculate the number of FBDs. As a result,
the hardware calculates the FBD incorrectly. Therefore, the driver
proactively updates the head pointer in each common poll to ensure that
the number of FBDs calculated by the hardware is correct.
Fixes: 68752b24f5 ("net: hns3: schedule the polling again when allocation fails")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver will send command to firmware to query pfc packet number
when user uses dcb tool to get pfc parameters. However, the periodic
service task will also periodically query and record MAC statistics,
including pfc packet number.
As the hardware registers of statistics is cleared after reading, it will
cause pfc packet number of MAC statistics are not correct after using dcb
tool to get pfc parameters.
To fix this problem, when user uses dcb tool to get pfc parameters, driver
updates MAC statistics firstly and then get pfc packet number from MAC
statistics.
Fixes: 64fd2300fc ("net: hns3: add support for querying pfc puase packets statistic")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, NIC init ROCE interrupt vector with MSIX interrupt. But ROCE use
pci_irq_vector() to get interrupt vector, which adds the relative interrupt
vector again and gets wrong interrupt vector.
So fixes it by assign relative interrupt vector to ROCE instead of MSIX
interrupt vector and delete the unused struct member base_msi_vector
declaration of hclgevf_dev.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when driver is failed to add a new multicast mac address to
hardware due to the multicast mac table is full, it will directly return.
In this case, if the multicast mac list has some reuse addresses after the
new address, those reuse addresses will never be added to hardware.
To fix this problem, if function hclge_add_mc_addr_common() returns
-ENOSPC, hclge_sync_vport_mac_list() should judge whether continue or
stop to add next address.
As function hclge_sync_vport_mac_list() needs parameter mac_type to know
whether is uc or mc, refine this function to add parameter mac_type and
remove parameter sync. So does function hclge_unsync_vport_mac_list().
Fixes: ee4bcd3b7a ("net: hns3: refactor the MAC address configure")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20211108201817.43121-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The priv->ntfy_blocks[] has "priv->num_ntfy_blks" elements so this >
needs to be >= to prevent an off by one bug. The priv->ntfy_blocks[]
array is allocated in gve_alloc_notify_blocks().
Fixes: 87a7f321bb ("gve: Recover from queue stall due to missed IRQ")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead of
accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom interrupt
code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force one interrupt
per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups
-----BEGIN PGP SIGNATURE-----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=mKh0
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, new features in others and some cleanups
all over the place.
Nothing really stands out and it is all relatively small.
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for
gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead
of accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom
interrupt code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force
one interrupt per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups"
* tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
virtio_gpio: drop packed attribute
gpio: virtio: Add IRQ support
gpio: realtek-otto: fix GPIO line IRQ offset
gpio: clean up Kconfig file
net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
gpio: mlxbf2: Introduce IRQ support
gpio: mc33880: Drop if with an always false condition
gpio: max730x: Make __max730x_remove() return void
gpio: aggregator: Wrap access to gpiochip_fwd.tmp[]
gpio: modepin: Add driver support for modepin GPIO controller
dt-bindings: gpio: zynqmp: Add binding documentation for modepin
firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
gpio: tps65218: drop unneeded MODULE_ALIAS
gpio: max77620: drop unneeded MODULE_ALIAS
gpio: xilinx: simplify getting .driver_data
gpio: tegra186: Support multiple interrupts per bank
gpio: tegra186: Force one interrupt per bank
gpio: uniphier: Use helper functions to get private data from IRQ data
gpio: uniphier: Use helper function to get IRQ hardware number
dt-bindings: gpio: add gpio-line-names to rockchip,gpio-bank.yaml
'netdev' is a managed resource allocated in the probe using
'devm_alloc_etherdev()'.
It must not be freed explicitly in the remove function.
Fixes: ee7da21ac4 ("net: Add driver for LiteX's LiteETH network interface")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prestera FW v4.0 support commit has been merged
accidentally w/o review comments addressed and waiting
for the final patch set to be uploaded. So, fix the remaining
comments related to structure laid out and build issues.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0 support")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings and spacing in hns3_ethtool.c:
hns3_ethtool.c:246: warning: No description found for return value of 'hns3_lp_run_test'
hns3_ethtool.c:408: warning: expecting prototype for hns3_nic_self_test(). Prototype was for hns3_self_test() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Peng Li <lipeng321@huawei.com>
Cc: Guangbin Huang <huangguangbin2@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
- Add pci_read_vpd_any(), pci_write_vpd_any() to access VPD at arbitrary
offsets (Heiner Kallweit)
- Use VPD API to replace custom code in cxgb3 driver (Heiner Kallweit)
* pci/vpd:
cxgb3: Remove seeprom_write and use VPD API
cxgb3: Use VPD API in t3_seeprom_wp()
cxgb3: Remove t3_seeprom_read and use VPD API
PCI/VPD: Use pci_read_vpd_any() in pci_vpd_size()
PCI/VPD: Add pci_read/write_vpd_any()
fix the remaining build issues reported by patchwork
in firmware v4.0 support commit which has been already
merged.
Fix patchwork issues:
- source inline
- checkpatch
Fixes: bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0 support")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mii ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but octeontx2-nicvf introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamp ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but oax88796 introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: a97c69ba4f ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build bot says:
>> drivers/net/ethernet/asix/ax88796c_main.c:1116:34: warning: unused variable 'ax88796c_dt_ids' [-Wunused-const-variable]
static const struct of_device_id ax88796c_dt_ids[] = {
^
The only reference to this array is wrapped in of_match_ptr().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: a97c69ba4f ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The octeontx2 pf nic driver failsz to link when the devlink support
is not reachable:
aarch64-linux-ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.o: in function `otx2_dl_mcam_count_get':
otx2_devlink.c:(.text+0x10): undefined reference to `devlink_priv'
aarch64-linux-ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.o: in function `otx2_dl_mcam_count_validate':
otx2_devlink.c:(.text+0x50): undefined reference to `devlink_priv'
aarch64-linux-ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.o: in function `otx2_dl_mcam_count_set':
otx2_devlink.c:(.text+0xd0): undefined reference to `devlink_priv'
aarch64-linux-ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.o: in function `otx2_devlink_info_get':
otx2_devlink.c:(.text+0x150): undefined reference to `devlink_priv'
This is already selected by the admin function driver, but not the
actual nic, which might be built-in when the af driver is not.
Fixes: 2da4894327 ("octeontx2-pf: devlink params support to set mcam entry count")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment of err will be overwritten next, so this statement
should be deleted.
The clang_analyzer complains as follows:
drivers/net/ethernet/broadcom/tg3.c:5506:2: warning:
Value stored to 'expected_sg_dig_ctrl' is never read
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF is removed and/or reset its Tx queues need to be
stopped from the PF. This is done by calling the ice_dis_vf_qs()
function, which calls ice_vsi_stop_lan_tx_rings(). Currently
ice_dis_vf_qs() is protected by the VF state bit ICE_VF_STATE_QS_ENA.
Unfortunately, this is causing the Tx queues to not be disabled in some
cases and when the VF tries to re-enable/reconfigure its Tx queues over
virtchnl the op is failing. This is because a VF can be reset and/or
removed before the ICE_VF_STATE_QS_ENA bit is set, but the Tx queues
were already configured via ice_vsi_cfg_single_txq() in the
VIRTCHNL_OP_CONFIG_VSI_QUEUES op. However, the ICE_VF_STATE_QS_ENA bit
is set on a successful VIRTCHNL_OP_ENABLE_QUEUES, which will always
happen after the VIRTCHNL_OP_CONFIG_VSI_QUEUES op.
This was causing the following error message when loading the ice
driver, creating VFs, and modifying VF trust in an endless loop:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by always calling ice_dis_vf_qs() and silencing the error
message in ice_vsi_stop_tx_ring() since the calling code ignores the
return anyway. Also, all other places that call ice_vsi_stop_tx_ring()
catch the error, so this doesn't affect those flows since there was no
change to the values the function returns.
Other solutions were considered (i.e. tracking which VF queues had been
"started/configured" in VIRTCHNL_OP_CONFIG_VSI_QUEUES, but it seemed
more complicated than it was worth. This solution also brings in the
chance for other unexpected conditions due to invalid state bit checks.
So, the proposed solution seemed like the best option since there is no
harm in failing to stop Tx queues that were never started.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VF was not able to change its hardware MAC address in case
the new address was already present in the MAC filter list.
Change the handling of VF add mac request to not return
if requested MAC address is already present on the list
and check if its hardware MAC needs to be updated in this case.
Fixes: ed4c068d46 ("ice: Enable ip link show on the PF to display VF unicast MAC(s)")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when a trusted VF enables promiscuous mode spoofchk will be
disabled. This is wrong and should only be modified from the
ndo_set_vf_spoofchk callback. Fix this by removing the call to toggle
spoofchk for trusted VFs.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a VF requests promiscuous mode and it's trusted and true promiscuous
mode is enabled the PF driver attempts to enable unicast and/or
multicast promiscuous mode filters based on the request. This is fine,
but there are a couple issues with the current code.
[1] The define to configure the unicast promiscuous mode mask also
includes bits to configure the multicast promiscuous mode mask, which
causes multicast to be set/cleared unintentionally.
[2] All 4 cases for enable/disable unicast/multicast mode are not
handled in the promiscuous mode message handler, which causes
unexpected results regarding the current promiscuous mode settings.
To fix [1] make sure any promiscuous mask defines include the correct
bits for each of the promiscuous modes.
To fix [2] make sure that all 4 cases are handled since there are 2 bits
(FLAG_VF_UNICAST_PROMISC and FLAG_VF_MULTICAST_PROMISC) that can be
either set or cleared. Also, since either unicast and/or multicast
promiscuous configuration can fail, introduce two separate error values
to handle each of these cases.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A typical collection of patches this cycle, mostly fixing with a few new
features:
- Fixes from static tools. clang warnings, dead code, unused variable,
coccinelle sweeps, etc
- Driver bug fixes and minor improvements in rxe, bnxt_re, hfi1, mlx5,
irdma, qedr
- rtrs ULP bug fixes an improvments
- Additional counters for bnxt_re
- Support verbs CQ notifications in EFA
- Continued reworking and fixing of rxe
- netlink control to enable/disable optional device counters
- rxe now can use AH objects for its UD path, fixing various bugs in the
process
- Add DMABUF support to EFA
-----BEGIN PGP SIGNATURE-----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=CxD0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A typical collection of patches this cycle, mostly fixing with a few
new features:
- Fixes from static tools. clang warnings, dead code, unused
variable, coccinelle sweeps, etc
- Driver bug fixes and minor improvements in rxe, bnxt_re, hfi1,
mlx5, irdma, qedr
- rtrs ULP bug fixes an improvments
- Additional counters for bnxt_re
- Support verbs CQ notifications in EFA
- Continued reworking and fixing of rxe
- netlink control to enable/disable optional device counters
- rxe now can use AH objects for its UD path, fixing various bugs in
the process
- Add DMABUF support to EFA"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (103 commits)
RDMA/core: Require the driver to set the IOVA correctly during rereg_mr
RDMA/bnxt_re: Remove unsupported bnxt_re_modify_ah callback
RDMA/irdma: optimize rx path by removing unnecessary copy
RDMA/qed: Use helper function to set GUIDs
RDMA/hns: Use the core code to manage the fixed mmap entries
IB/opa_vnic: Rebranding of OPA VNIC driver to Cornelis Networks
IB/qib: Rebranding of qib driver to Cornelis Networks
IB/hfi1: Rebranding of hfi1 driver to Cornelis Networks
RDMA/bnxt_re: Use helper function to set GUIDs
RDMA/bnxt_re: Fix kernel panic when trying to access bnxt_re_stat_descs
RDMA/qedr: Fix NULL deref for query_qp on the GSI QP
RDMA/hns: Modify the value of MAX_LP_MSG_LEN to meet hardware compatibility
RDMA/hns: Fix initial arm_st of CQ
RDMA/rxe: Make rxe_type_info static const
RDMA/rxe: Use 'bitmap_zalloc()' when applicable
RDMA/rxe: Save a few bytes from struct rxe_pool
RDMA/irdma: Remove the unused variable local_qp
RDMA/core: Fix missed initialization of rdma_hw_stats::lock
RDMA/efa: Add support for dmabuf memory regions
RDMA/umem: Allow pinned dmabuf umem usage
...
On m68k:
In function ‘prestera_hw_build_tests’,
inlined from ‘prestera_hw_switch_init’ at drivers/net/ethernet/marvell/prestera/prestera_hw.c:788:2:
././include/linux/compiler_types.h:335:38: error: call to ‘__compiletime_assert_345’ declared with attribute error: BUILD_BUG_ON failed: sizeof(struct prestera_msg_switch_attr_req) != 16
...
The driver assumes structure members are naturally aligned, but does not
add explicit padding, thus breaking architectures where integral values
are not always naturally aligned (e.g. on m68k, __alignof(int) is 2, not
4).
Fixes: bb5dbf2cc6 ("net: marvell: prestera: add firmware v4.0 support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211102082433.3820514-1-geert@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:446:8-56: WARNING
avoid newline at end of message in NL_SET_ERR_MSG_MOD.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211102020312.16567-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch allows to use 0 for `coal->rx_coalesce_usecs` param to
disable rx irq coalescing.
Previously we could enable rx irq coalescing via ethtool
(For ex: `ethtool -C eth0 rx-usecs 2000`) but we couldn't disable
it because this part rejects 0 value:
if (!coal->rx_coalesce_usecs)
return -EINVAL;
Fixes: 84da2658a6 ("TI DaVinci EMAC : Implement interrupt pacing functionality.")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20211101152343.4193233-1-bigunclemax@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
