The following errors are noticed during boot on a QCS404 board:
[ 2.926647] qcom_icc_rpm_smd_send mas 6 error -6
[ 2.934573] qcom_icc_rpm_smd_send mas 8 error -6
These errors show when we try to configure the GPU and display nodes.
Since these particular nodes aren't supported on RPM and are purely
local, we should just change their mas_rpm_id to -1 to avoid any
requests being sent for these master IDs.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201118111044.26056-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Some nodes are incorrectly marked as RPM-controlled (they have RPM
master and slave ids assigned), but are actually controlled by the
application CPU instead. The RPM complains when we send requests for
resources that it can't control. Let's fix this by replacing the IDs,
with the default "-1" in which case no requests are sent.
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20201112105140.10092-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
It has been reported that on Fairphone 2 (msm8974-based), increasing
the clock rate for some of the NoCs during boot may lead to hangs.
Let's restore the original behavior and not touch the clock rate of
any of the NoCs to fix the regression.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Link: https://lore.kernel.org/r/20201109124512.10776-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When sync_state support got introduced recently, by default we try to
set the NoCs to run initially at maximum rate. But as these values are
aggregated, we may end with a really big clock rate value, which is
then converted from "u64" to "long" during the clock rate rounding.
But on 32bit platforms this may result an overflow. Fix it by making
sure that the rate is within range.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20201106144847.7726-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
In addition to the rest of Qcom interconnect drivers use icc_sync_state
for SM8150/SM8250 interconnect drivers to notify the interconnect
framework when all consumers are probed and there is no need to keep the
bandwidth set to maximum anymore.
Also move the BCM initialization before creating the nodes to set the
max bandwidth in hardware for the initialization/probing stage.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Link: https://lore.kernel.org/r/20201027133418.976687-1-dmitry.baryshkov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Take into account the initial bandwidth from the framework and update
the internal sum and max values before committing if needed. This will
ensure that the floor bandwidth values are enforced until the providers
get into sync state.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Tested-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20201021155938.9223-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-3-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently if we use sync_state, by default the bandwidth is maxed out,
but in order to set this in hardware, the BCMs (Bus Clock Managers) need
to be initialized first. Move the BCM initialization before creating the
nodes to fix this.
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-2-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When setting the initial bandwidth, make sure to call the aggregate()
function (if such is implemented for the current provider), to handle
cases when data needs to be aggregated first.
Fixes: b1d681d8d3 ("interconnect: Add sync state support")
Acked-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20201013135913.29059-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
After enabling interconnect scaling for display on the db845c board,
in certain configurations the board hangs, while the following errors
are observed on the console:
Error sending AMC RPMH requests (-110)
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
qcom_rpmh TCS Busy, retrying RPMH message send: addr=0x50000
...
In this specific case, the above is related to one of the sequencers
being stuck, while client drivers are returning from probe and trying
to disable the currently unused clock and interconnect resources.
Generally we want to keep the multimedia NoC enabled like the rest of
the NoCs, so let's set the keepalive flag on it too.
Fixes: aae57773fb ("interconnect: qcom: sdm845: Split qnodes into their respective NoCs")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Mike Tipton <mdtipton@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20201012194034.26944-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902172433.1138-2-krzk@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902172433.1138-1-krzk@kernel.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* icc-syncstate:
interconnect: Add get_bw() callback
interconnect: Add sync state support
interconnect: qcom: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Lowering the bandwidth on the bus might have negative consequences if
it's done before all consumers had a chance to cast their vote. Now by
default the framework sets the bandwidth to maximum during boot. We need
to use the icc_sync_state callback to notify the framework when all
consumers are probed and there is no need to keep the bandwidth set to
maximum anymore.
Link: https://lore.kernel.org/r/20200825170152.6434-4-georgi.djakov@linaro.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The bootloaders often do some initial configuration of the interconnects
in the system and we want to keep this configuration until all consumers
have probed and expressed their bandwidth needs. This is because we don't
want to change the configuration by starting to disable unused paths until
every user had a chance to request the amount of bandwidth it needs.
To accomplish this we will implement an interconnect specific sync_state
callback which will synchronize (aggregate and set) the current bandwidth
settings when all consumers have been probed.
Link: https://lore.kernel.org/r/20200825170152.6434-3-georgi.djakov@linaro.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
These structures aren't modified at runtime. Mark them const so they get
moved to read-only memory. We have to cast away const in one place when
we store into the data member of struct icc_node. This is paired with a
re-const of the data member when it is extracted in qcom_icc_set().
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200914182112.513981-1-swboyd@chromium.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-7-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use the qcom_icc_xlate_extended() in order to parse tags, that are
specified as an additional arguments to the path endpoints in DT.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-5-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Implement a function to parse the arguments of the "interconnects" DT
property and populate the interconnect path tags if this information
is available.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200903133134.17201-4-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently there is the xlate() callback, which is used by providers for
mapping the nodes from phandle arguments. That's fine for simple mappings,
but the phandle arguments could contain an additional data, such as tag
information. Let's create another callback xlate_extended() for the cases
where providers want also populate the path tag data.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200903133134.17201-2-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently, bcm-voter always assumes requests are made in KBps and that
BCM HW always wants them in Bps, so it always scales the requests by
1000. However, certain use cases and BCMs may use different units.
Thus, add support for BCM-specific scaling factors.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-7-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Change the default TCS wait behavior to only wait for completion in AMC
and WAKE. Waiting isn't necessary in the SLEEP TCS, since votes are only
being removed in this case. Resources can be safely disabled
asynchronously in parallel with the rest of the power collapse sequence.
This reduces the sleep entry latency.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-6-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently, all bcm-voters set tcs_cmd::wait=true for the last VCD
command in each TCS (AMC, WAKE, and SLEEP). However, some bcm-voters
don't need the completion and instead need to optimize for latency. For
instance, disabling wait-for-completion in the WAKE set can decrease
resume latency and allow for certain operations to occur in parallel
with the WAKE TCS triggering. This is only safe in very specific
situations. Keep the default behavior of always waiting, but allow it to
be overridden in devicetree.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-5-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add generic qcom interconnect bindings that are common across platforms. In
particular, these include QCOM_ICC_TAG_* macros that clients can use when
calling icc_set_tag().
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200903192149.30385-3-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SM8250 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Based on SC7180 driver and generated from downstream dts.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200728023811.5607-6-jonathan@marek.ca
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SM8150 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Based on SC7180 driver and generated from downstream dts.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200728023811.5607-5-jonathan@marek.ca
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There are drivers which just need to get multiple interconnect paths,
request some predefined amounts of bandwidth and then just toggle the
paths between enabled/disabled state.
The aim of this patch is simplify the above and to allow drivers to put
all the path names and bandwidth data into a single static icc_bulk_data
table and call the icc_bulk_* functions on that table in order to scale
all the interconnect paths in parallel.
Suggested-by: Evan Green <evgreen@chromium.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200729123439.9961-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Small BW votes that translate to less than a single BCM unit are
currently truncated to zero. Ensure that non-zero BW requests always
result in at least a vote of 1 to BCM.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-2-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
For disabled paths the 'interconnect_summary' in debugfs currently shows
the orginally requested bandwidths. This is confusing, since the bandwidth
requests aren't active. Instead show the bandwidths for disabled
paths/requests as zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200729104933.1.If8e80e4c0c7ddf99056f6e726e59505ed4e127f3@changeid
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylccQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymofgCfZ1CxNWd0ZVM0YIn8cY9gO6ON7MsAnRq48hvn
Vjf4rKM73GC11bVF4Gyy
=Xq1R
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
When an interconnect path is being disabled, currently we don't aggregate
the requests for it afterwards. But the re-aggregation step shouldn't be
skipped, as it may leave the nodes with outdated bandwidth data. This
outdated data may actually keep the path still enabled and prevent the
device from going into lower power states.
Reported-by: Atul Dhudase <adhudase@codeaurora.org>
Fixes: 7d374b2090 ("interconnect: Add helpers for enabling/disabling a path")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Atul Dhudase <adhudase@codeaurora.org>
Reviewed-by: Atul Dhudase <adhudase@codeaurora.org>
Link: https://lore.kernel.org/r/20200721120740.3436-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200723083735.5616-2-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently rpmh_invalidate() always returns success. Update its
return type to void.
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1592485553-29163-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds support for a new boolean 'inter_set' field in struct
icc_provider. Setting it to 'true' enables calling '->set' for
inter-provider node pairs. All existing users of the interconnect
framework allocate this structure with kzalloc, and are therefore
unaffected by this change.
This makes it easier for hierarchies like exynos-bus, where every bus
is probed separately and registers a separate interconnect provider, to
model constraints between buses.
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200521122841.8867-4-s.nawrocki@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This patch relaxes the condition in of_icc_get_from_provider() so that
it is no longer required to set '#interconnect-cells' to <1> in the DT,
and therefore it is not required to supply dummy node IDs in the
'interconnects' property when node IDs are dynamically generated rather
than hardcoded (statically allocated).
In case of the devfreq driver for exynos-bus, node IDs are dynamically
allocated and '#interconnect-cells' is always zero.
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20200521122841.8867-3-s.nawrocki@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This patch makes the above function public (for use in exynos-bus devfreq
driver).
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20200521122841.8867-2-s.nawrocki@samsung.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
- Add support for interconnect bandwidth to the OPP core (Georgi
Djakov, Saravana Kannan, Sibi Sankar, Viresh Kumar).
- Add support for regulator enable/disable to the OPP core (Kamil
Konieczny).
- Add boost support to the CPPC cpufreq driver (Xiongfeng Wang).
- Make the tegra186 cpufreq driver set the
CPUFREQ_NEED_INITIAL_FREQ_CHECK flag (Mian Yousaf Kaukab).
- Prevent the ACPI power management from using power resources
with devices where the list of power resources for power state
D0 (full power) is missing (Rafael Wysocki).
- Annotate a hibernation-related function with __init (Christophe
JAILLET).
-----BEGIN PGP SIGNATURE-----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=p5eu
-----END PGP SIGNATURE-----
Merge tag 'pm-5.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are operating performance points (OPP) framework updates mostly,
including support for interconnect bandwidth in the OPP core, plus a
few cpufreq changes, including boost support in the CPPC cpufreq
driver, an ACPI device power management fix and a hibernation code
cleanup.
Specifics:
- Add support for interconnect bandwidth to the OPP core (Georgi
Djakov, Saravana Kannan, Sibi Sankar, Viresh Kumar).
- Add support for regulator enable/disable to the OPP core (Kamil
Konieczny).
- Add boost support to the CPPC cpufreq driver (Xiongfeng Wang).
- Make the tegra186 cpufreq driver set the
CPUFREQ_NEED_INITIAL_FREQ_CHECK flag (Mian Yousaf Kaukab).
- Prevent the ACPI power management from using power resources with
devices where the list of power resources for power state D0 (full
power) is missing (Rafael Wysocki).
- Annotate a hibernation-related function with __init (Christophe
JAILLET)"
* tag 'pm-5.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: Avoid using power resources if there are none for D0
cpufreq: CPPC: add SW BOOST support
cpufreq: change '.set_boost' to act on one policy
PM: hibernate: Add __init annotation to swsusp_header_init()
opp: Don't parse icc paths unnecessarily
opp: Remove bandwidth votes when target_freq is zero
opp: core: add regulators enable and disable
opp: Reorder the code for !target_freq case
opp: Expose bandwidth information via debugfs
cpufreq: dt: Add support for interconnect bandwidth scaling
opp: Update the bandwidth on OPP frequency changes
opp: Add sanity checks in _read_opp_key()
opp: Add support for parsing interconnect bandwidth
cpufreq: tegra186: add CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
OPP: Add helpers for reading the binding properties
dt-bindings: opp: Introduce opp-peak-kBps and opp-avg-kBps bindings
Pull operating performance points (OPP) framework changes for v5.8
from Viresh Kumar:
"This contains:
- support for interconnect bandwidth in the OPP core (Georgi Djakov,
Saravana Kannan, Sibi Sankar, Viresh Kumar).
- support for regulator enable/disable (Kamil Konieczny).
This is based on three patches from the interconnect tree which
shall get merged via Greg's tree."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Don't parse icc paths unnecessarily
opp: Remove bandwidth votes when target_freq is zero
opp: core: add regulators enable and disable
opp: Reorder the code for !target_freq case
opp: Expose bandwidth information via debugfs
cpufreq: dt: Add support for interconnect bandwidth scaling
opp: Update the bandwidth on OPP frequency changes
opp: Add sanity checks in _read_opp_key()
opp: Add support for parsing interconnect bandwidth
interconnect: Remove unused module exit code from core
interconnect: Disallow interconnect core to be built as a module
interconnect: Add of_icc_get_by_index() helper function
OPP: Add helpers for reading the binding properties
dt-bindings: opp: Introduce opp-peak-kBps and opp-avg-kBps bindings
Expose the bandwidth information as well via debugfs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
These are the interconnect changes for the 5.8-rc1 merge window:
Core changes:
- Convert the framework core from tristate to bool to make handling
dependencies between other core frameworks easier
- Add of_icc_get_by_index()
- Add devm_of_icc_get() helper function
- Add icc_enable() and icc_disable() helpers
New drivers:
- Platform driver for NXP i.MX8MM SoC
- Platform driver for NXP i.MX8MN SoC
- Platform driver for NXP i.MX8MQ SoC
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=+f9u
-----END PGP SIGNATURE-----
Merge tag 'icc-5.8-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect changes for 5.8
These are the interconnect changes for the 5.8-rc1 merge window:
Core changes:
- Convert the framework core from tristate to bool to make handling
dependencies between other core frameworks easier
- Add of_icc_get_by_index()
- Add devm_of_icc_get() helper function
- Add icc_enable() and icc_disable() helpers
New drivers:
- Platform driver for NXP i.MX8MM SoC
- Platform driver for NXP i.MX8MN SoC
- Platform driver for NXP i.MX8MQ SoC
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.8-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: Remove unused module exit code from core
interconnect: Disallow interconnect core to be built as a module
interconnect: Add of_icc_get_by_index() helper function
interconnect: Add helpers for enabling/disabling a path
interconnect: imx: Fix return value check in imx_icc_node_init_qos()
interconnect: imx: Add platform driver for imx8mn
interconnect: imx: Add platform driver for imx8mq
interconnect: imx: Add platform driver for imx8mm
interconnect: Add imx core driver
dt-bindings: interconnect: Add bindings for imx8m noc
interconnect: Add devm_of_icc_get() as exported API for users
This is an immutable branch shared with the OPP tree. It contains also
the patches to convert the interconnect framework from tristate to bool
after Greg agreed with that. This will make the integration between
the OPP layer and interconnect much easier.
* icc-get-by-index:
interconnect: Add of_icc_get_by_index() helper function
interconnect: Disallow interconnect core to be built as a module
interconnect: Remove unused module exit code from core
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The interconnect core is currently always built in:
menuconfig INTERCONNECT
bool "On-Chip Interconnect management support"
So remove the module_exit function and symbolically rename module_init
to device_initcall to drive home the point.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1572546532-19248-3-git-send-email-jcrouse@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Building individual drivers as modules is fine but allowing a core
framework to be built as a module makes it really complex and should be
avoided.
Whatever uses the interconnect core APIs must also be built as a module
if interconnect core is built as module, else we will see compilation
failures.
If another core framework (like cpufreq, clk, etc), that can't be built
as module, needs to use interconnect APIs then we will start seeing
compilation failures with allmodconfig configurations as the symbols
(like of_icc_get()) used in other frameworks will not be available in
the built-in image.
Disallow the interconnect core to be built as a module to avoid all
these issues.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/b789cce388dd1f2906492f307dea6780c398bc6a.1567065991.git.viresh.kumar@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This is the same as the traditional of_icc_get() function, but the
difference is that it takes index as an argument, instead of name.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200512125327.1868-4-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is a repeated pattern in multiple drivers where they want to switch
the bandwidth between zero and some other value. This is happening often
in the suspend/resume callbacks. Let's add helper functions to enable and
disable the path, so that callers don't have to take care of remembering
the bandwidth values and handle this in the framework instead.
With this patch the users can call icc_disable() and icc_enable() to lower
their bandwidth request to zero and then restore it back to it's previous
value.
Suggested-by: Evan Green <evgreen@chromium.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200507120846.8354-1-georgi.djakov@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
In case of error, the function of_parse_phandle() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: f0d8048525 ("interconnect: Add imx core driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20200509030214.14435-1-weiyongjun1@huawei.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add a platform driver for the i.MX8MM SoC describing bus topology.
Bandwidth adjustments is currently only supported on the DDRC and main
NOC. Scaling for the vpu/gpu/display NICs could be added in the future.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/b14eef179dbd837a486619724b8033490f49db72.1586174566.git.leonard.crestez@nxp.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This adds support for i.MX SoC family to interconnect framework.
Platform drivers can describe the interconnect graph and several
adjustment knobs where icc node bandwidth is converted to a
DEV_PM_QOS_MIN_FREQUENCY request.
The interconnect provider is probed through the main NOC device and
other adjustable nodes on the same graph are found from a
fsl,scalable-nodes phandle array property.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Link: https://lore.kernel.org/r/35920e673df6c04cbbb7d877a7d4ba25fd91a784.1586174566.git.leonard.crestez@nxp.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Users can use devm version of of_icc_get() to benefit from automatic
resource release.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1586946198-13912-2-git-send-email-akashast@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently, if tcs_cmd_gen is called with commit=false, then
tcs_cmd::wait is left uninitialized. Since the tcs_cmd structures passed
to this function aren't zero-initialized, then we're left with random
wait values. This results in waiting for completion for more commands
than is necessary, depending on what's on the stack at the time.
Removing the unnecessary if-condition fixes this, but add an explicit
memset of the tcs_cmd structure as well to ensure predictable behavior
if more tcs_cmd members are added in the future.
Fixes: 976daac4a1 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200319231021.18108-1-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200415130327.23059-2-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a pull request with interconnect changes for the 5.7-rc1 merge
window. It contains just driver updates, and these are:
- Refactoring of the SDM845 driver, which is now improved to better
represent the hardware.
- New driver for SC7180 platforms.
- New driver for OSM L3 interconnect hardware found on SDM845/SC7180
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=jHM0
-----END PGP SIGNATURE-----
Merge tag 'icc-5.7-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect changes for 5.7
Here is a pull request with interconnect changes for the 5.7-rc1 merge
window. It contains just driver updates, and these are:
- Refactoring of the SDM845 driver, which is now improved to better
represent the hardware.
- New driver for SC7180 platforms.
- New driver for OSM L3 interconnect hardware found on SDM845/SC7180
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.7-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: qcom: Add OSM L3 support on SC7180
dt-bindings: interconnect: Add OSM L3 DT binding on SC7180
interconnect: qcom: Add OSM L3 interconnect provider support
dt-bindings: interconnect: Add OSM L3 DT bindings
interconnect: qcom: Allow icc node to be used across icc providers
interconnect: qcom: Add SC7180 interconnect provider driver
dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
interconnect: qcom: sdm845: Split qnodes into their respective NoCs
interconnect: qcom: Consolidate interconnect RPMh support
dt-bindings: interconnect: Update Qualcomm SDM845 DT bindings
dt-bindings: interconnect: Add YAML schemas for QCOM bcm-voter
dt-bindings: interconnect: Convert qcom,sdm845 to DT schema
Add Operating State Manager (OSM) L3 interconnect provider support on
SC7180 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200227105632.15041-6-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
On some Qualcomm SoCs, Operating State Manager (OSM) controls the
resources of scaling L3 caches. Add a driver to handle bandwidth
requests to OSM L3 from CPU on SDM845 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200227105632.15041-4-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Move the icc node ids to a common header, this will allow for
referencing/linking of icc nodes to multiple icc providers on
SDM845 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200227105632.15041-2-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in SC7180 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1583241493-21212-3-git-send-email-okukatla@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When we allocate memory, kasprintf() can fail and we must check its
return value.
Fixes: 05309830e1 ("interconnect: Add a name to struct icc_path")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200226110420.5357-2-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to better represent the hardware and its different Network-On-Chip
devices, split the sdm845 provider driver into NoC specific providers.
Remove duplicate functionality already provided by the icc rpmh and
bcm voter drivers to calculate and commit bandwidth requests to hardware.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200209183411.17195-6-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add bcm voter driver and add support for RPMh specific interconnect
providers which implements the set and aggregate functionalities that
translates bandwidth requests into RPMh messages. These modules provide
a common set of functionalities for all Qualcomm RPMh based interconnect
providers and should help reduce code duplication when adding new
providers.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200228095951.15457-1-sibis@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the Qualcomm interconnect buses found in MSM8916 based
platforms. The topology consists of three NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use IS_ERR() to ensure that the path passed to icc_set_bw() is valid.
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Now we can have a tag associated with the path. Add this information
to the interconnect_summary file, as the current information in debugfs
is incomplete.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The interconnect graphs can be difficult to understand and the current
"interconnect_summary" file doesn't even display links in any way.
Add a new "interconnect_graph" file to debugfs in the graphviz "dot"
format which describes interconnect providers, nodes and links.
The file is human-readable and can be visualized by piping through
graphviz. Example:
ssh $TARGET cat /sys/kernel/debug/interconnect/interconnect_graph \
| dot -Tsvg > interconnect_graph.svg
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Now we have a common function for standard aggregation, so let's use it,
instead of duplicating the code.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Currently there is one very standard aggregation method that is used by
several drivers. Let's add this as a common function, so that drivers
could just point to it, instead of copy/pasting code.
Suggested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The tracepoints can help with understanding the system behavior of a
given interconnect path when the consumer drivers change their bandwidth
demands. This might be interesting when we want to monitor the requested
interconnect bandwidth for each client driver. The paths may share the
same nodes and this will help to understand "who and when is requesting
what". All this is useful for subsystem drivers developers and may also
provide hints when optimizing the power and performance profile of the
system.
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When debugging interconnect things, it turned out that saving the path
name and including it in the traces is quite useful, especially for
devices with multiple paths.
For the path name we use the one specified in DT, or if we use platform
data, the name is based on the source and destination node names.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Move the interconnect framework internal structs into a separate file,
so that it can be included and used by ftrace code. This will allow us
to expose some more useful information in the traces.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is a new helper function for removing all nodes. Let's use it instead
of duplicating the code.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The removal of all nodes from a provider seem to be a common functionality
for all existing users and it would make sense to factor out this into a
a common helper function.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
As we will remove items off the list using list_del(), we need to use the
safe version of list_for_each_entry().
Fixes: 4e60a9568d ("interconnect: qcom: add msm8974 driver")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20191212075332.16202-5-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we will remove items off the list using list_del(), we need to use the
safe version of list_for_each_entry().
Fixes: 5e4e6c4d3a ("interconnect: qcom: Add QCS404 interconnect provider driver")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Cc: <stable@vger.kernel.org> # v5.4
Link: https://lore.kernel.org/r/20191212075332.16202-4-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we will remove items off the list using list_del(), we need to use the
safe version of list_for_each_entry().
Fixes: b5d2f74107 ("interconnect: qcom: Add sdm845 interconnect provider driver")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://lore.kernel.org/r/20191212075332.16202-3-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20191212075332.16202-2-georgi.djakov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must ensure that the tag is not changed while we aggregate the
requests. Currently the icc_set_tag() is not using any locks and this
may cause the values to be aggregated incorrectly. Fix this by acquiring
the icc_lock while we set the tag.
Link: https://lore.kernel.org/lkml/20191018141750.17032-1-georgi.djakov@linaro.org/
Fixes: 127ab2cc5f ("interconnect: Add support for path tags")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
This is a struct with a trailing zero-length array of icc_node pointers
but it's allocated as if it were a single array of icc_nodes instead.
This allocates too much memory at probe time but shouldn't have any
noticeable effect. Both sdm845 and qcs404 are affected.
Fix by replacing kcalloc with kzalloc and using the "struct_size" macro.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 5e4e6c4d3a ("interconnect: qcom: Add QCS404 interconnect provider driver")
Link: https://lore.kernel.org/linux-pm/a7360abb6561917e30bbfaa6084578449152bf1d.1569348056.git.leonard.crestez@nxp.com/
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
There is one compilation error when CONFIG_INTERCONNECT_QCOM_QCS404=y and
CONFIG_INTERCONNECT_QCOM_SMD_RPM=y, as well as CONFIG_COMPILE_TEST=y,
but CONFIG_QCOM_SMD_RPM is not set, logs as below:
drivers/interconnect/qcom/smd-rpm.o: In function `qcom_icc_rpm_smd_send':
smd-rpm.c:(.text+0xe4): undefined reference to `qcom_rpm_smd_write'
Makefile:1071: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
This is because
INTERCONNECT_QCOM_QCS404 depends on QCOM_SMD_RPM || COMPILE_TEST.
Here CONFIG_COMPILE_TEST=y, so CONFIG_INTERCONNECT_QCOM_SMD_RPM
is selected. If CONFIG_QCOM_SMD_RPM is not set, then
qcom_rpm_smd_write() is not defined, and compilation error happen.
Fix this by removing COMPILE_TEST from CONFIG_INTERCONNECT_QCOM_QCS404.
Fixes: 5e4e6c4d3a ("interconnect: qcom: Add QCS404 interconnect provider driver")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add driver for the interconnect buses found in Qualcomm QCS404-based
platforms. The topology consists of three NoCs that are controlled by
a remote processor. This remote processor collects the aggregated
bandwidth for each master-slave pairs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
On some Qualcomm SoCs, there is a remote processor, which controls some of
the Network-On-Chip interconnect resources. Other CPUs express their needs
by communicating with this processor. Add a driver to handle communication
with this remote processor.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add support for wake and sleep commands by using a tag to indicate
whether or not the aggregate and set requests fall into execution
state specific bucket.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Introduce an optional callback in interconnect provider drivers. It can be
used for implementing actions, that need to be executed before the actual
aggregation of the bandwidth requests has started.
The benefit of this for now is that it will significantly simplify the code
in provider drivers.
Suggested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Consumers may have use cases with different bandwidth requirements based
on the system or driver state. The consumer driver can append a specific
tag to the path and pass this information to the interconnect platform
driver to do the aggregation based on this state.
Introduce icc_set_tag() function that will allow the consumers to append
an optional tag to each path. The aggregation of these tagged paths is
platform specific.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
When consumers report their bandwidth needs with icc_set_bw(), it's
possible that the requested amount of bandwidth is not available or just
the new configuration fails to apply on some path. In this case revert to
the previous configuration and propagate the error back to the consumers
to let them know that bandwidth is not available, hardware is busy or
whatever error is returned by the interconnect platform driver.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce Qualcomm SDM845 specific provider driver using the
interconnect framework.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a functionality to provide information about the current constraints
per each node and provider.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we support only platform data for specifying the interconnect
endpoints. As now the endpoints are hard-coded into the consumer driver
this may lead to complications when a single driver is used by multiple
SoCs, which may have different interconnect topology.
To avoid cluttering the consumer drivers, introduce a translation function
to help us get the board specific interconnect data from device-tree.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a new API to get requirements and configure the
interconnect buses across the entire chipset to fit with the current
demand.
The API is using a consumer/provider-based model, where the providers are
the interconnect buses and the consumers could be various drivers.
The consumers request interconnect resources (path) between endpoints and
set the desired constraints on this data flow path. The providers receive
requests from consumers and aggregate these requests for all master-slave
pairs on that path. Then the providers configure each node along the path
to support a bandwidth that satisfies all bandwidth requests that cross
through that node. The topology could be complicated and multi-tiered and
is SoC specific.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
