Make ack health code easies to read. Compared to previous
code, we do not print debug messages when expected_ack_cnt_delta == 0
and also do check against negative deltas.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional change, make recover from statistics code
easies to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With commit 554d1d027b only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The beacon notification changed between 4965 and
agn because the embedded TX response changed, but
iwlwifi was never updated to know about this.
Update it now so the IBSS manager status will be
tracked correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Allow peers to size their reorder buffer more
accurately by advertising that we'll never send
aggregates longer than the default (31).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In order to support RSN IBSS, we need to
(ok actually maybe it's just easiest to)
disable group key programming so that any
group-addressed frames will be decrypted
in software which handles the per-station
keys for this easily. We could keep the
encryption in the device, but that takes
more work and seems unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The I/Q swapping is extremely important and should be dealt with extra care.
It will affects OFDM and CCK differently.
For 6000/6005/6030 series devices, the I/Q were swapped, and for 2000 series
devices, it is in non-swapped status (but its swapped with respected to 6000/6005/6030).
so the CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER register need to be set to support
the correct behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Driver check alive message from ucode, if it is not ok, then need
to restart the loading process. instead of checking multiple places
for failure, only need to check in once place when receive alive
message from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
After commit 59eb21a650
"cfg80211: Extend channel to frequency mapping for 802.11j"
we use uninitialized sband->band when assign channel frequencies, what
results that 5GHz channels have erroneous (zero) center_freq value.
Patch fixes problem and simplifies code a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only use IWL_RATE_COUNT_3945 in 3945 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e error "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If PAN functionality is present, advertise
P2P interface type support and thus support
for P2P. However, the support is currently
somewhat incomplete -- NoA schedule isn't
added to probe responses, and 11b bitrates
may be used still, etc. Therefore, make it
all optional with a Kconfig option.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a number of places where the minimum
slot time is hardcoded to 20 TU, add a new
constant for that and use it everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For device supporting PAN/P2P, use the PAN
context to implement the remain-on-channel
operation using device offloads so that the
filters in the device will be programmed
correctly -- otherwise we cannot receive
any probe request frames during off-channel
periods.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlagn powersave algorithm uses the supports_idle parameter
to tell the device to save power when it is not associated with
an AP and is idle.
Enable this feature for the 1000 series of devices.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
the sram data dumped through the debugfs interface would only work properly
when dumping data on even u32 boundaries and swap bytes based on endianness
on that boundary making byte arrays impossible to read.
now addresses are displayed at the start of every line and the data is
displayed consistently if dumping 1 byte or 20 and regardless of what is the
starting address.
if no lenght given, address displayed is u32 in device format
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Adding 2000 series devices supports, the 2000 series devices has
many different SKUs which includes 1x1 and 2x2 devices,also with
and without BT combo.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since 6005, 6030 and 6150 series are offical released, remove the reference
to gen2x and use the product number instead.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of keeping track of LED blink speed
in the driver, use the new mac80211 trigger
and link it up with an LED classdev that we
now register. This also allows users more
flexibility in how they want to have the LED
blink or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The notification wait support code is shared
between 4965 and other AGN devices, so 4965
also has to initialize the data structures
for it, otherwise it crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously I hacked this with an msleep(300)
which was fine since we never had longer PAN
time slots, but now that we will have them I
need to fix that. Use the new notification
wait support to properly wait for the WIPAN
deactivation complete signal from the ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.
Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not used or likely to be needed from other
files, so it can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For all the new devices, the sku information should read from EEPROM
but for legacy devices such as 4965, appearly the EEPROM does not
contain the necessary information. so skip the read from EEPROM
and go back to use software configuration.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looks that we do not set correctly antennas when scanning
on 5Ghz band and when bluetooth is enabled, because
priv->cfg->scan_tx_antennas[band] is only defined for
IEEE80211_BAND_2GHZ.
To fix we check band before limiting antennas to first one.
This allow to remove hard coded cfg->scan_tx_antennas[band].
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 6cd0b1cb87 "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The below patch fixes a typo "diable" to "disable". Please let me know if this
is correct or not.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
# iw wlan0 interface add moni0 type monitor flags control
# ip link set moni0 up
causes a continuous spew of FH_ERROR from the
device. Fix this by not setting the CTL2HOST
filter by itself -- CTL + promisc works fine.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’
dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:
[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
#ifdef CONFIG_MAC80211_DEBUGFS
struct dentry *rs_sta_dbgfs_scale_table_file;
struct dentry *rs_sta_dbgfs_stats_table_file;
struct dentry *rs_sta_dbgfs_rate_scale_data_file;
struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
u32 dbg_fixed_rate;
#endif
The issue was introduced by commit a1da077bc3:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
patch "iwlagn: check ready in iwlagn_bss_info_changed()" introduce
whitespace, fix it
please merge with the previous patch
Reported by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple devices use almost the same .cfg with minor differences.
Use macro and remove the duplication. By doing this, reduce
the chance for mistake while modify .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For WiFi/WiMAX combo devices, if WiMAX own the RF, WiFi driver
try to access RF and fail. This is the W/A to To avoid WiFi keep
reloading firmware and try to access RF again.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For logging EEPROM related info, instead of using IWL_DEBUG_INFO,
use the dedicated logging (IWL_DEBUG_EEPROM) for easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This removes the old TX power reading code, it isn't
necessary since the new code is able to read all the
various EEPROM layouts due to relying on information
contained in the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For the new 1x1 devices, hw and uCode will support rx
antenna diversity, but we need to indicate 1x1 device to
AccessPoint to make sure it won't use MIMO.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The compiler correctly warns:
iwl-agn-tx.c: In function ‘iwlagn_tx_status_reply_compressed_ba’:
iwl-agn-tx.c:1240: warning: ‘bitmap’ may be used uninitialized in this function
Move the debug print to the branch that reads the
bitmap, and move the variables too so it's more
obvious where they are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In function iwlagn_bss_info_changed(), we need to check if the driver
is ready before doing real work. Also, the previously put WARN() is
removed because the vif is not guaranteed to be valid. uCode restart
routine will clear the vif.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This prevent bad fixed_rate keeps crashing uCode in an endless loop.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
From: Johannes Berg <johannes.berg@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.
Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.
Tested on 3945, 4965, 5300, 6300.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similarly like on iwlagn, initialize reset duration on iwl3945 to prevent
too frequent firmware resets.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the module parameter name to bt_ch_inhibition from
bt_ch_announce to better describe the functionality
In order to allow Bluetooth to activate a smart AFH mechanism
and to maximize its available bandwidth the WiFi will request
BT Core to inhibit its activity in channels that interfere
with WiFi activity (and vice versa) if bt_ch_inhibition is enabled
Set module parameter "bt_ch_inhibition=0" will disable the channel
inhibition function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If driver is on the way down, there is no need to send
RXON to uCode, check the condition before continuous the process.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
PCI L1 Active needs to be disabled while loading the uCode so that the bus
doesn't go to sleep. The enablement of L1 Active should be done after
the uCode has sent the ALIVE response. The enablement of L1 Active was
missing.
Enabling L1 Active allows to save power if the BIOS / bus driver allows
it.
I measured the power consumption while not associated and
idle/associated:
L1 Active disabled: 39 mA = 130mW
L1 Active enabled: 6 mA = 20 mW
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
During reprogram stations, do not send link quality command.
uCode will crash if receive link quality command for invalid station
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Commit dbbf1755b0 "iwlwifi: use
antenna information in EEPROM" caused 4965 device breakage with
"Microcode SW error detected. Restarting 0x82000000." message.
This patch reverts 4965 part of that commit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change to offical name for 100 devices:
"Intel(R) Centrino(R) Wireless-N 100"
Change to offical name for 130 devices:
"Intel(R) Centrino(R) Wireless-N 130"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change to offical name for 6000g2b devices:
"Intel(R) Centrino(R) Wireless-N 1030"
"Intel(R) Centrino(R) Advanced-N 6230"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of hardcoding the numbers that must
match mac80211, use the constants. Not that
this means we could change the constants,
but at least this way it's clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Our hardware has reliable TX status, but we're
not currently advertising that to mac80211.
Since the packet loss monitoring will depend
on it, advertise it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since aggregation queues are station-specific, the
device will not reject packets in them but rather
will stop the appropriate aggregation queues when
a station goes to sleep. I forgot to account for
this in the driver, so if a station went to sleep
that had aggregation enabled, traffic would stop
indefinitely.
Fix this by only accounting frames queued on the
normal AC queues for associated station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Through races, a packet may be enqueued for
transmission to a station while that station
is going to sleep, in which case the warning
here triggers. Instead of warning, check the
condition -- if this packet is not a PS-poll
response then we still enqueue it but it will
be rejected by the device since the station
is marked as asleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The valid tx/rx antenna information is part of EEPROM, so use it
to configure the device.
For few cases, the EEPROM did not reflect the correct antenna, but
it is too late to modify the EEPROM, so overwrite with .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For 6000g2b and up, adding advance power management support
for better power consumption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If shadow register is enable, modify the power management
command to inform uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding additional power management option available for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
48644 57 12120 60821 ed95 drivers/net/wireless/b43/phy_n.o.new
48661 57 12120 60838 eda6 drivers/net/wireless/b43/phy_n.o.old
37906 86 7904 45896 b348 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.new
37937 86 7904 45927 b367 drivers/net/wireless/iwlwifi/iwl-agn-lib.o.old
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.new
37781 523 6752 45056 b000 drivers/net/wireless/iwlwifi/iwl-3945.o.old
Changed b43_nphy_write_clip_detection to take a const u16 *
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If only 3945 is selected, and is a module, build
fails because iwl-legacy.c won't be compiled. Fix
this by adding it to the build correctly.
This doesn't happen for 4965 because it is a bool
option, not tristate, since it's built into the
AGN module.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract of jiffies is fine even if one variable overwrap.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simplify length calculation in iwlagn_tx_skb, that function
is enough complex, without fuzz it more than necessary.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting rxon chain and filter, no need to commit RXON when the
chain flag is not changed. This reduces the number of RXON commands
we send down to uCode.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
RXON command without association bit can clear the QoS info in the
uCode. Therefore, before sending the associated RXON, we need to
send the QoS command just in case.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When the DTIM is not 1, then the slot timing is in
some cases required to be calclulated based on the
DTIM interval instead of the beacon interval, fix
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of unconditionally sending unassoc RXON,
before any assoc RXON, re-send only the AP STA
entry which is required after the BSSID has been
programmed into the device to set up internal
filters in the microcode properly.
This fixes some issues that we correlated with
sending a lot of RXON commands to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For reasons that aren't entirely clear to me,
we sometimes get here during hardware reset
without the interface being set. Don't crash,
but keep a warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Currently, when a PAN queue needs to be
stopped, we erroneously stop queue number 5
(for example) with mac80211 -- which doesn't
even exist!
To avoid that problem, recalculate the swq_id
for all queues when setting up the queues,
and don't use the default identity mapping
that is acceptable for devices which don't
support PAN.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Previously, we used the swq_id's mechanism
to have AC and HW queue different only for
aggregation queues. To be able to fix a bug
with iPAN simply always build the swq_id as
ac | (hwq << 2) and remove the flag bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of passing the txq->swq_id, pass the
txq struct directly to make sure that in the
future nobody will pass an invalid number.
Only three places actually change from using
the txq_id or the skb's queue_mapping to now
using txq->swq_id as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Even if this check were to happen, using the
txq_id here (which is a HW queue) would lead
to confusion in mac80211. Luckily, it doesn't
seem like this can ever happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some variables are misnamed in the FIFO setup
code, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Set the default led mode for different devices.
For the newer devices such as 6000g2a, 6000g2b and newer,
the default led mode is On/Off instead of blinking.
The led_mode still can be control through module parameter
0: system default
1: On/Off
2: blinking
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For newer devices, uCode provide both "number of frames sent"
and "number of frames acked" information inside the compressed_ba
packet. So instead of figure the success/failure information through
the bitmap, use those information which is much betrer approach.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were two type of isr supported by iwlwifi devices.
legacy isr - only used by legacy devices (3945 & 4965)
ict isr - used by all new generation of iwlwifi devices
Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 100 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 130 series device, 6000g2b uCode will be used, no need to
have additional defines for 130 devices, so remove those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding description to Kconfig to indicate more devices
are being supported by iwlagn
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While BT is on and doing iscan and/or pscan, BT is in listen
mode which will impact WiFi throughput, we need to
enable dynamic smps in order to improve the rx throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement switching the interface while an
interface is up in iwlwifi. Interfaces have
to stay on the context they were created on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch to clean up all RXON handling
inadvertently broke IBSS because it failed to
take into account that unlike in AP mode, IBSS
requires beacons to be sent only after setting
the RXON assoc.
Fix this, clean up the code a bit, improve the
error checking around this, and also react to
beacon changes in IBSS mode from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to simplify the flow, and make new
enhancements easier, separate out the RXON
processing for modern AGN (5000 and newer)
from RXON processing for the older 3945 and
4965 devices. Avoid changing these old ones
to avoid regressions and move their code to
a new file (iwl-legacy.c). 4965 gets the
commit_rxon that used to be common for all
AGN devices, but with removed PAN support.
The new RXON processing is more central and
does more work in committing, so that it is
easier to follow.
To make it more evident what is split out
for legacy, split the necessary operations
for that into a new struct iwl_legacy_ops.
Those parts that still exist in the new AGN
code don't need to be parametrized.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resending RXON timing here caused issues with
dual-mode under certain circumstances, so avoid
doing it here right now.
This effectively reverts b01efe434b
and partially 2491fa42d9. The next
patch will make all this cleaner for just the
devices that need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, 4965 and modern AGN devices will
need to have different mac80211 callbacks since
they have different capabilities. Prepare for
that by making the mac80211 operations a device
config.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new PCI PM and let the PCI core code handle the PCI-specific
details of power transitions.
Based on similarly titled ath9k patch posted by Rafael J. Wysocki.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Currently we are canceling scan when changing BSSID. Behave the same
when changing association and beacon enablement, to avoid committing
rxon during scan in iwl_set_no_assoc().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not set power mode when scanning, and defer that when scan finish.
We still set power mode in force case i.e. when device is overheated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid sending commands to firmware (including commit_rxon) when scan
is pending and we are calling iwlagn_bt_traffic_change_work simultaneously.
Also comment some innocent race conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost anywhere in the code we avoid committing rxon while performing
scan, and make rxon commit when scan complete. However in some places
in the code we do not follow that rule. This patch fix that problem in
iwlagn_configure_filter().
Since we do not commit directly in iwl3945_configure_filter, we can
also do the same for agn, so I just remove iwlcore_commit_rxon()
function and add a comment. Also change comment for iwl3945.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to comment in iwl_bg_scan_completed, setting tx power should
be deferred during pending scan, but we are not doing this.
This patch change code to really defer setting tx power after scan
complete. Additionally refactor iwl_set_tx_power code and call
lib->send_tx_power() directly from iwlagn_commit_rxon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 5xxx and 6xxx change to send tx_power_cmd command synchronously,
to do not start other commands when setting tx power is pending.
We currently do the same for 4956 and 3945.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add WARN_ONCE when scanning is pending. Use STATUS_SCAN_HW bit since we
can have scan canceled or completed but STATUS_SCANNING bit still set.
v1 -> v2: replace EIO to EAGAIN
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.
This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing. This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Some of the functions in iwl-eeprom.c file are for agn devices only,
Those functions do not have to be part of iwlcore.ko, so move those
to iwl-agn-eeprom.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When the beacon_skb is NULL, we might still
attempt to use it in this code path (if we
ever get here) -- make the code a bit more
defensive and check the return value of
iwl_fill_beacon_frame() against zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We recently found that contrary to expectations,
the LED is not blinking in IBSS mode. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The RXON checking is a bit magical, and prints
out too much information if something goes wrong.
Make it less magical and print out only the items
that were actually wrong.
Also remove the comment about removing it -- the
driver is constantly changing so these checks are
useful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For 6050 series of devices, 6050 ops should be used;
One of the 6050 config still use 6000 ops, fix it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no need to check for NULL before
calling dev_kfree_skb() since it is valid
to call it on NULL -- it becomes a no-op.
There's also no need to initialise the
beacon_skb variable to NULL just after
the memory it is in has been kzalloc'ed.
Some minor whitespace cleanups, and a
lock assertion in a function that needs
the mutex (to access the beacon_skb var)
complete the patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since we're also going to support AP (GO) mode,
the variable isn't used for just IBSS beacons
any more -- rename it to not mislead readers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are two passive 2.4 GHz channels: 12 and 13.
If you have a hidden SSID on those, you will not
be able to connect to it because we don't send out
probe requests there. We can allow this by using
the firmware's probe-after-rx functionality on
those channels as well.
This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16462
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For BT/WiFi combo devices, need longer tx stuck queue
timer, so those devices won't reload firmware too often.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
commit 6f98613258b966ffe0e6def18129b386514d10e0
Author: Jay Sternberg <jay.e.sternberg@intel.com>
Date: Sat Sep 18 09:07:04 2010 -0700
iwlagn: reduce redundant parameter definitions
broke 3945 because Jay accidentally removed the
num_of_queues parameter for 3945, so that we now
attempt to allocate a zero-sized queue array,
which leads to SLUB returning ZERO_SIZE_PTR (0x10)
which we then try to dereference thus crashing the
system. Restore the necessary num_of_queues param.
This fixes
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2254
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For WiFi/BT combo devices, priority table always need to download
before perform any calibration operation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
6000g2 devices need to have temperature offset calibration. The runtime
uCode needs to receive the calibration results just like BB and LO
calibration. To do this, driver reads the offset value from NVM and send
it to uCode after runtime uCode is alive.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn driver uses the IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE
as the chain noise reset calibration index and
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE+1 as the chain noise gain
calibration index, if not specified by the TLV value in the new
firmware format.
However, this is broken if we need to add more calibrations like
the temperature offset calibration because we increased
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE by 1.
To fix this issue, define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE
and use it as the calibration index instead. We still keep the
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE as a sanity check for
the TLV value given by ucode.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For experimental uCode, it should work with the driver
if driver has experimental uCode support option enabled;
remove the API version checking.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The recent scanning code shuffle accidentally
moved the SCAN_HW bit setting _after_ the PAN
parameters are modified, which means that they
don't take the scan into account -- fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The function is used exactly once, and the caller
doesn't even need the special check, it can be
simplified to a simple bit check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A number of declarations in iwl-core.h should
be in agn specific files, and also rename the
iwl-calib.h file to iwl-agn-calib.h to better
reflect that it belongs to agn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since all devices share the same operation here,
there's no need to call it indirectly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This operation is only ever called from set_hw_params,
which is also already based on the config/ops, so that
there's no need to have a separate set_ct_kill op and
we can just call the right ct_threshold function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_dump_fh function is only used
by the agn module, so it can be there
instead of being exported by the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_dump_csr function is only used
within the agn module, so it can be
moved there instead of being exported
by the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_toggle_tx_ant function is only used
by agn code, so it can be moved into the
agn module instead of being exported from
the core.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Code and data related to agn bitrates can be
part of the agn module rather than being in
the core module.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A number of exports, especially related to
thermal throttling, are unnecessary because
the code lives in the same module that it
is used in, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The code to print out TX failure reasons is
AGN specific, so it can be in the AGN module.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.
before:
text data bss dec hex filename
212886 3872 96 216854 34f16 iwlcore.ko
620542 10448 304 631294 9a1fe iwlagn.ko
314013 3264 196 317473 4d821 iwl3945.ko
after:
text data bss dec hex filename
202857 3872 92 206821 327e5 iwlcore.ko
629102 10448 308 639858 9c372 iwlagn.ko
314240 3264 196 317700 4d904 iwl3945.ko
delta:
-10029 iwlcore.ko
8560 iwlagn.ko
227 iwl3945.ko
so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All drivers share the same implementation, so
there's no need to call this via a function
pointer nor to export it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
