The Regulator based PSE controller driver relies on regulator support to
be enabled. If regulator support is disabled, it will still compile
fine, but won't operate correctly.
Hence add a dependency on REGULATOR, to prevent asking the user about
this driver when configuring a kernel without regulator support.
Fixes: 66741b4e94 ("net: pse-pd: add regulator based PSE driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/709caac8873ff2a8b72b92091429be7c1a939959.1664900558.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add generic, regulator based PSE driver to support simple Power Sourcing
Equipment without automatic classification support.
This driver was tested on 10Bast-T1L switch with regulator based PoDL PSE.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add interface to support Power Sourcing Equipment. At current step it
provides generic way to address all variants of PSE devices as defined
in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4
PoDL Power Sourcing Equipment (PSE).
Currently supported and mandatory objects are:
IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus
IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl
This is minimal interface needed to control PSE on each separate
ethernet port but it provides not all mandatory objects specified in
IEEE 802.3-2018.
Since "PoDL PSE" and "PSE" have similar names, but some different values
I decide to not merge them and keep separate naming schema. This should
allow as to be as close to IEEE 802.3 spec as possible and avoid name
conflicts in the future.
This implementation is connected to PHYs instead of MACs because PSE
auto classification can potentially interfere with PHY auto negotiation.
So, may be some extra PHY related initialization will be needed.
With WIP version of ethtools interaction with PSE capable link looks
as following:
$ ip l
...
5: t1l1@eth0: <BROADCAST,MULTICAST> ..
...
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: disabled
PoDL PSE Power Detection Status: disabled
$ ethtool --set-pse t1l1 podl-pse-admin-control enable
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: enabled
PoDL PSE Power Detection Status: delivering power
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This framework was create with intention to provide support for Ethernet PSE
(Power Sourcing Equipment) and PDs (Powered Device).
At current step this patch implements generic PSE support for PoDL (Power over
Data Lines 802.3bu) specification with reserving name space for PD devices as
well.
This framework can be extended to support 802.3af and 802.3at "Power via the
Media Dependent Interface" (or PoE/Power over Ethernet)
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
