Improve reliability of the mailbox communication and remove
its potential flaws that may lead to the undefined or faulty behavior.
Recently some users reported issues on ESX with 10G Intel NICs which were
found to be caused by incorrect implementation of the PF-VF mailbox
communication.
Technical investigation highlighted areas to improve in the communication
between PF or VF that wants to send the message (sender) and the other
part which receives the message (receiver):
- Locking the mailbox when the sender wants to send a message
- Releasing the mailbox when the communication ends
- Returning the result of the mailbox message execution
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add legacy suffix to mailbox functions which should be backwards compatible
with older PF drivers. Communication during API negotiation always has to
be done using the earlier implementation.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new handling for error codes:
IXGBE_ERR_CONFIG - ixgbe_mbx_operations is not correctly set
IXGBE_ERR_TIMEOUT - mailbox operation, e.g. poll for message, timeout
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is name similarity within IXGBE_VT_MSGTYPE_ACK and
PFMAILBOX.ACK / VFMAILBOX.ACK. MSGTYPE macros are renamed to SUCCESS and
FAILURE because they are not specified in datasheet and now will be
easily distinguishable.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Properly reconfigure VF VSIs after VF request ADQ.
Created new function to update queue mapping and queue pairs per TC
with AQ update VSI. This sets proper RSS size on NIC.
VFs num_queue_pairs should not be changed during setup of queue maps.
Previously, VF main VSI in ADQ had configured too many queues and had
wrong RSS size, which lead to packets not being consumed and drops in
connectivity.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the i40e_vsi_setup_queue_map is basing the count of queues in
TCs on a VSI's alloc_queue_pairs member which is not changed throughout
any user's action (for example via ethtool's set_channels callback).
This implies that vsi->tc_config.tc_info[n].qcount value that is given
to the kernel via netdev_set_tc_queue() that notifies about the count of
queues per particular traffic class is constant even if user has changed
the total count of queues.
This in turn caused the kernel warning after setting the queue count to
the lower value than the initial one:
$ ethtool -l ens801f0
Channel parameters for ens801f0:
Pre-set maximums:
RX: 0
TX: 0
Other: 1
Combined: 64
Current hardware settings:
RX: 0
TX: 0
Other: 1
Combined: 64
$ ethtool -L ens801f0 combined 40
[dmesg]
Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!
Reason was that vsi->alloc_queue_pairs stayed at 64 value which was used
to set the qcount on TC0 (by default only TC0 exists so all of the
existing queues are assigned to TC0). we update the offset/qcount via
netdev_set_tc_queue() back to the old value but then the
netif_set_real_num_tx_queues() is using the vsi->num_queue_pairs as a
value which got set to 40.
Fix it by using vsi->req_queue_pairs as a queue count that will be
distributed across TCs. Do it only for non-zero values, which implies
that user actually requested the new count of queues.
For VSIs other than main, stay with the vsi->alloc_queue_pairs as we
only allow manipulating the queue count on main VSI.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Co-developed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the reason of null pointer dereference in sync VSI filters.
Added new I40E_VSI_RELEASING flag to signalize deleting and releasing
of VSI resources to sync this thread with sync filters subtask.
Without this patch it is possible to start update the VSI filter list
after VSI is removed, that's causing a kernel oops.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting VLAN port increasing RX queue max_pkt_size
by 4 bytes to take VLAN tag into account.
Trigger the VF reset when setting port VLAN for
VF to renegotiate its capabilities and reinitialize.
Fixes: ba4e003d29 ("i40e: don't hold spinlock while resetting VF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eric Dumazet says:
====================
net: make dev_watchdog() less intrusive
dev_watchdog() is used on many NIC to periodically monitor TX queues
to detect hangs.
Problem is : It stops all queues, then check them, then 'unfreeze' them.
Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.
With many TX queues, this is becoming more visible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for stopping all TX queues from dev_watchdog()
Not only this stops feeding the NIC, it also migrates all qdiscs
to be serviced on the cpu calling netif_tx_unlock(), causing
a potential latency artifact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are not fast path, there is no point in inlining them.
Also provide netif_freeze_queues()/netif_unfreeze_queues()
so that we can use them from dev_watchdog() in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In following patches, dev_watchdog() will no longer stop all queues.
It will read queue->trans_start locklessly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_timeout_show() assumed dev_watchdog() would stop all
the queues, to fetch queue->trans_timeout under protection
of the queue->_xmit_lock.
As we want to no longer disrupt transmits, we use an
atomic_long_t instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: david decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the values of EVENT_* constants from bit masks to bit numbers as
accepted by {clear,set,test}_bit() functions.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net_hdr_to_skb does not set the skb's gso_size and gso_type
correctly for UFO packets received via virtio-net that are a little over
the GSO size. This can lead to problems elsewhere in the networking
stack, e.g. ovs_vport_send dropping over-sized packets if gso_size is
not set.
This is due to the comparison
if (skb->len - p_off > gso_size)
not properly accounting for the transport layer header.
p_off includes the size of the transport layer header (thlen), so
skb->len - p_off is the size of the TCP/UDP payload.
gso_size is read from the virtio-net header. For UFO, fragmentation
happens at the IP level so does not need to include the UDP header.
Hence the calculation could be comparing a TCP/UDP payload length with
an IP payload length, causing legitimate virtio-net packets to have
lack gso_type/gso_size information.
Example: a UDP packet with payload size 1473 has IP payload size 1481.
If the guest used UFO, it is not fragmented and the virtio-net header's
flags indicate that it is a GSO frame (VIRTIO_NET_HDR_GSO_UDP), with
gso_size = 1480 for an MTU of 1500. skb->len will be 1515 and p_off
will be 42, so skb->len - p_off = 1473. Hence the comparison fails, and
shinfo->gso_size and gso_type are not set as they should be.
Instead, add the UDP header length before comparing to gso_size when
using UFO. In this way, it is the size of the IP payload that is
compared to gso_size.
Fixes: 6dd912f826 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it.
Fixes: 7472dd9f64 ("staging: fsl-dpaa2/eth: Move print message")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.
Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the used PHYs also support hardware timestamping, all configuration requests
should be forwared to the PHYs instead of being processed by the MAC driver
itself.
This enables PHY timestamping in combination with the cpsw driver.
Tested with an am335x based board with two DP83640 PHYs connected to the cpsw
switch.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update net_failover documentation with missing and incomplete
details to get a proper working setup.
Signed-off-by: Vasudev Kamath <vasudev@copyninja.info>
Reviewed-by: Krishna Kumar <krikku@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cross-reference for the handbooks section works. However, it is
meant to describe the path inside the Kernel's doc where the section
is, but there's an space instead of a dash, plus it lacks the .rst at
the end, which makes:
./scripts/documentation-file-ref-check
to complain.
Fixes: 604370e106 ("Documentation/process: Add maintainer handbooks section")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The file name: accounting/delay-accounting.rst
should be, instead: Documentation/accounting/delay-accounting.rst.
Also, there's no need to use doc:`foo`, as automarkup.py will
automatically handle plain text mentions to Documentation/
files.
So, update its cross-reference accordingly.
Fixes: fcb5017045 ("delayacct: Document task_delayacct sysctl")
Fixes: c3123552aa ("docs: accounting: convert to ReST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Russell King says:
====================
net: ocelot_net: phylink validate implementation updates
This series converts ocelot_net to fill in the supported_interfaces
member of phylink_config, cleans up the validate() implementation,
and then converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_net has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy interface mode bitmap for the MSCC Ocelot driver with
the interface modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: mtk_eth_soc: phylink validate implementation updates
This series converts mtk_eth_soc to fill in the supported_interfaces
member of phylink_config, cleans up the validate() implementation, and
then converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mtk_eth_soc has no special behaviour in its validation implementation,
so can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a better method to select SFP interface modes, we
no longer need to use phylink_helper_basex_speed() in a driver's
validation function, and we can also get rid of our hack to indicate
both 1000base-X and 2500base-X if the comphy is present to make that
work. Remove this hack and use of phylink_helper_basex_speed().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy interface mode bitmap for the Mediatek driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: sparx5: phylink validate implementation updates
This series converts sparx5 to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparx5 has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparx5_phylink_validate() no longer needs to check for
PHY_INTERFACE_MODE_NA as phylink will walk the supported interface
types to discover the link mode capabilities. Neither is it necessary
to check the device capabilities as we will not be called for
unsupported interface modes. Remove these checks.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Microchip Sparx5 driver
with interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: enetc: phylink validate implementation updates
This series converts enetc to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc has no special behaviour in its validation implementation, so can
be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Freescale enetc driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: xilinx: phylink validate implementation updates
This series converts axienet to fill in the supported_interfaces member
of phylink_config, cleans up the validate() implementation, and then
converts to phylink_generic_validate().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Xilinx axienet driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates for mlx5 driver:
1) Support ethtool cq mode
2) Static allocation of mod header object for the common case
3) TC support for when local and remote VTEPs are in the same
4) Create E-Switch QoS objects on demand to save on resources
5) Minor code improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmGUhbkACgkQSD+KveBX
+j4qdgf/d6XXNJkcvUSBaUAuPYcO9BjqFDU/UeKycWG2sgcKN0kZ3xv0LhM/I4Bo
jBeXp273BslLd5E0eJeeLCmN91TlsHk9ClNoyM7BwnIfylBQZch1GVQWznsnbcM8
z7isCGXYBBYUpmdvt5PNpNmdk3q/e5P9ZoM8UDGWVZsREedI5efrA4bYY8LkM/BE
KRv+ok4JoLSfG6oi2qsW0dmrKEBAfWNZw6xJT87CjCljwk1d+3jQQE/t7kRqMMRD
hLDbBGa26ZANTQPQWRPQCt/HQFu2N57jSEKaSPKdPM3AGstx5DwdmyvPGkZyZTor
YGZiPARvSgfCOPCfa7oJ7xEZj18gBA==
=iQhD
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-11-16
Updates for mlx5 driver:
1) Support ethtool cq mode
2) Static allocation of mod header object for the common case
3) TC support for when local and remote VTEPs are in the same
4) Create E-Switch QoS objects on demand to save on resources
5) Minor code improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmGUEocACgkQSD+KveBX
+j6ynwf/UKQ4I+ZexNfgDmINn4qNgGjnOOq8EfaPPBUzUODObmgPHV7fPT8ADX3b
sLx7CgVGRHnk36XqDhptYrIDEtbfa26epRvr3PGU4FcUmz+PoJprQtWBK2B5PDiT
nwSmxerEauiji7LxlXx9YmtfpnbeHDFanjJyYbVnuZkqREMP7S/B73KLFnW7WEyU
EyEKu+oahGx3C4CiF7Fg20w9mP2fujC7pw+og+g6T9dDiF/ynTCf1KZMXq1EwA1M
+/GS37Lm4VEoCrumiF6HGYmr9gRIFhMXBTaTRYzuz/d7FPxFrtF/88IF0xfmFmLr
7SNBWjmNnjnCaXNIlY1IbyHh9/P83Q==
=a7ES
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2021-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2021-11-16
Please pull this mlx5 fixes series, or let me know in case of any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
When calling setattr_prepare() to determine the validity of the attributes the
ia_{g,u}id fields contain the value that will be written to inode->i_{g,u}id.
When the {g,u}id attribute of the file isn't altered and the caller's fs{g,u}id
matches the current {g,u}id attribute the attribute change is allowed.
The value in ia_{g,u}id does already account for idmapped mounts and will have
taken the relevant idmapping into account. So in order to verify that the
{g,u}id attribute isn't changed we simple need to compare the ia_{g,u}id value
against the inode's i_{g,u}id value.
This only has any meaning for idmapped mounts as idmapping helpers are
idempotent without them. And for idmapped mounts this really only has a meaning
when circular idmappings are used, i.e. mappings where e.g. id 1000 is mapped
to id 1001 and id 1001 is mapped to id 1000. Such ciruclar mappings can e.g. be
useful when sharing the same home directory between multiple users at the same
time.
As an example consider a directory with two files: /source/file1 owned by
{g,u}id 1000 and /source/file2 owned by {g,u}id 1001. Assume we create an
idmapped mount at /target with an idmapping that maps files owned by {g,u}id
1000 to being owned by {g,u}id 1001 and files owned by {g,u}id 1001 to being
owned by {g,u}id 1000. In effect, the idmapped mount at /target switches the
ownership of /source/file1 and source/file2, i.e. /target/file1 will be owned
by {g,u}id 1001 and /target/file2 will be owned by {g,u}id 1000.
This means that a user with fs{g,u}id 1000 must be allowed to setattr
/target/file2 from {g,u}id 1000 to {g,u}id 1000. Similar, a user with fs{g,u}id
1001 must be allowed to setattr /target/file1 from {g,u}id 1001 to {g,u}id
1001. Conversely, a user with fs{g,u}id 1000 must fail to setattr /target/file1
from {g,u}id 1001 to {g,u}id 1000. And a user with fs{g,u}id 1001 must fail to
setattr /target/file2 from {g,u}id 1000 to {g,u}id 1000. Both cases must fail
with EPERM for non-capable callers.
Before this patch we could end up denying legitimate attribute changes and
allowing invalid attribute changes when circular mappings are used. To even get
into this situation the caller must've been privileged both to create that
mapping and to create that idmapped mount.
This hasn't been seen in the wild anywhere but came up when expanding the
testsuite during work on a series of hardening patches. All idmapped fstests
pass without any regressions and we add new tests to verify the behavior of
circular mappings.
Link: https://lore.kernel.org/r/20211109145713.1868404-1-brauner@kernel.org
Fixes: 2f221d6f7b ("attr: handle idmapped mounts")
Cc: Seth Forshee <seth.forshee@digitalocean.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
CC: linux-fsdevel@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Seth Forshee <sforshee@digitalocean.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Don't create eswitch QoS (root TSAR) on switch mode change. Create it on
first child TSAR object creation - vport or rate group. Keep track
root TSAR references and release root TSAR with last object deletion.
No need to check for QoS is enabled when installing tc matchall filter.
Remove related helper function due to no users of it.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
