We need to set left/right control for the speaker amp to get stereo
output on speaker.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec is in slave mode, ASRC can suppress noise for asynchronous
MCLK and LRCLK or special I2S format. This patch defines an API to select
the clock source for specified filters. And the codec driver will turn on ASRC
for these filters if ASRC is selected as their clock source.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous definition of registers 0x84 and 0x85 doesn't match the datasheet.
So this patch removes the wrong definition and writes a new one for the two
registers.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
System clock is necessary for rt5670 JD function. We assume system
clock source will be set in machine driver. So there are two things
left we should do in codec driver.
1. Set sysclk to codec internal clock in probe since machine driver
may not do that before JD function is registered.
2. Power up PLL once sysclk source is switched to PLL.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds runtime PM support on rt5670 codec.
Signed-off-by: Lin Mengdong <mengdong.lin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set specific data according to dmi data.
Signed-off-by: Jin, Yao <yao.jin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we will configure dmic related pin definition if pdata.dmic_en
is true. However, there is no disable option in the enum. So, any dmic is
used, all 3 dmic related pins will be configured. It may cause unexpected
pin definition. This patch adds a disable item for each dmic enum and
take it as default. So the driver will not set the pin configuration if
we don't set dmicx_data_pin in platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU08iuAAoJECTWi3JdVIfQ9cUH/1ZNkoS67zEj/wsvcS+co/Dp
hInq7mAwO/usFfFWMzb68Lofc4g5yTGE+vtTAhggmzMGuqjXEMCAS/tO85EoA65d
2f0YNw7gEhUyp0oYPe5tS3I0F8O7ES+u27PwmM8sGO0KdCc9qrb3ppZN3BkEcr2U
akg854atOcKwBvGRLNSyj79WPkjNyMcM/kWkJCEHFLysu8rSilZ+UaekH+CUw02E
hstLM+PlM0LE/9rKmQvRyx6cnVqKqPWxalG0mCtBwpdHLYMn4yDFc3nn71lMn3oQ
/TIcHSfDCRgx3VVW8daBjNHqLgfg4XCcZ5W646zrpyyrlXRCCPJT8N0SY9jZUU4=
=ScU7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-ac97-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: AC'97 fixes
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
Another one liner that arrived after the earlier pull request. There's
a trivial conflict with my -next branch, I'll send a pull request with
that resolution and some other new stuff before Monday.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU09ESAAoJECTWi3JdVIfQZ+oH/10mjezNacUT0hFqZsNTQyFq
bG1pnU/szkZeMaP0Y1/fHawwgafOcGOPCU6DYDiN7KnNLdCdMW9slxSyZhigD+kV
G/eopUu0hPQOvlqq+ODGQ3eJ92kBefXzv5v4ophnqeaCdJm+uZbWqvPykVDp8Tqq
Og7R7AXX9BncCvLCiwhl9KCfKu61DViuCMLWNSbOkoZcRReMeRny0dXLG9WXWx3U
db72KflC4TZ5i8miKXAqTW/HHLhT8AL+v+B/3I8h/cDCRY6MvkU2qYE01Yvboull
RJMNuANKgMCVkEnp9izVzGXT/cUTCF6YCQSaPbUkSDWhbTOwirgF7BJBRir1xdM=
=vv5N
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-intel-v3.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix for Intel firmware name
Another one liner that arrived after the earlier pull request. There's
a trivial conflict with my -next branch, I'll send a pull request with
that resolution and some other new stuff before Monday.
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When SCC work in DSP A mode, the data outputs/inputs are shift out on
falling edge, the frame sync are sample on the rising edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.
The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
According to the I2S specification information as following:
- WS = 0, channel 1 (left)
- WS = 1, channel 2 (right)
So, the start event should be TF/RF falling edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In some cases it is necessary to before additional operations after the
device has been initialized and before the device is registered. This can
for example be resetting the device.
This patch introduces a new function snd_soc_alloc_ac97_codec() which is
similar to snd_soc_new_ac97_codec() except that it does not register the
device. Any users of snd_soc_alloc_ac97_codec() are responsible for calling
device_add() manually.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e512e001da ("ASoC: simple-card: Fix the reference count of device nodes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not send IPC stream commands to FW when the stream is
NULL, dereference the NULL pointer may also occur without precheck.
Here add NULL pointer checks for these stream APIs.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The probe routine was disabling the clock even
if the system was configured successfully. Add
a return statement to leave clocks enabled.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of block allocator, ba->offset, should not be changed during
fixed address allocating, for the caller may treat it as the offset of
allocated memory and use it. In the case that we allocate more than 1
blocks, we should make sure this offset is correct.
Here introduces a temp allocator for the later continuous allocating.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ts3a227e does not trigger interrupt to report jack status when system
boots from warm reset because ts3a227e's power remains on during warm reset.
Read jack status at probe to get current jack status.
Note that if system boots from EC reset, then this issue will not
happen.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The xDC field should have 5 bit width according to Reference Manual.
Thus this patch fixes it.
Signed-off-by: Aurelien BOUIN <a_bouin@yahoo.fr>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since RK3288 DMAC's burst length only support max to 4, here
set maxburst of playback and capture dma data to 4.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to description about "Transmit Data Level",
This bit field controls the level at which a DMA request
is made by the transmit logic.
It is equal to the watermark level.
That is, the dma_tx_req signal is generated when the number
of valid data entries in the TXFIFO
(TXFIFO0 if CSR=00
TXFIFO1 if CSR=01
TXFIFO2 if CSR=10
TXFIFO3 if CSR=11)
is equal to or below this field value.
Different to receive data level, transmit data level does not need
to "-1".
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
