Improve gxl-s905x-khadas-vim wifi performance
* change freq from 60Mhz to 100Mhz
100Mhz works well same as in meson-khadas-vim3.dtsi
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210622044334.769791-1-art@khadas.com
The NanoPi K2 has a AP6212 WiFi+BT combo module. The WiFi portion is
already enabled. The BT part is connected via UART and I2S.
Enable the UART and add a device node describing the Bluetooth portion
of the module.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210712135919.32059-1-wens@kernel.org
While there is no publicly available schematic of this board, it's not
hard to determine voltage of GPIO port C, D and G (only ones which can
be set).
Port C and G are used for MMC/SDIO communication, so they use 1.8 V
power supply. It's not clear if port D is even used, but if it is, it's
pretty safe to assume it uses 3.3 V power supply. Value read from PIO
Group Withstand Voltage Mode Select register from within pre-installed
Android agrees with that assesment.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210722161220.51181-3-jernej.skrabec@gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmD95yIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqp0H/j/xHL20EHaUJOaV
iJjnfGyjtnkLC5FCoV/q/v9sFuSW2p4W1nyF8/eIgVKObef94Mg4/xxaHQrWIM56
cbzK9aIcD9InAuImJ6lju4fqjNmFrt2x7mhfzjPKqmhfINfZ5CohpLFN5XdOwzYC
l+ZgmUUl7GLDAND2M6rtkc7AOk4qTyAySDvvPFELE/uNgV4EKaENSIWofHhEzW5v
Yk+4agawaFTfa6H9+uMVYZBOcEKwheQ0E2tcOJvHJT8Mwm8MFoC/B7fLY5zxIdN2
7A7r/7qbSQmSDSjOgwKS4ZOjom0xGSD+V+596SzET6jkbahR2HJ/mrFvmD7GNEoW
OWJPjzI=
=vzIM
-----END PGP SIGNATURE-----
Backmerge tag 'v5.14-rc3' into drm-next
Linux 5.14-rc3
Daniel said we should pull the nouveau fix from fixes in here, probably
a good plan.
Signed-off-by: Dave Airlie <airlied@redhat.com>
FlexCAN on i.MX8MP is not derived from i.MX6Q, instead reuses from
i.MX8QM with extra ECC added and default is enabled, so that the FlexCAN
would be put into freeze mode without FLEXCAN_QUIRK_DISABLE_MECR quirk.
This patch removes "fsl,imx6q-flexcan" fallback compatible string since
it's not compatible with the i.MX6Q.
Link: https://lore.kernel.org/r/20210719073437.32078-1-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here are some USB fixes for 5.14-rc3 to resolve a bunch of tiny problems
reported. Included in here are:
- dtsi revert to resolve a problem which broke android systems
that relied on the dts name to find the USB controller device.
People are still working out the "real" solution for this, but
for now the revert is needed.
- core USB fix for pipe calculation found by syzbot
- typec fixes
- gadget driver fixes
- new usb-serial device ids
- new USB quirks
- xhci fixes
- usb hub fixes for power management issues reported
- other tiny fixes
All have been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYPrXzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymtAQCeLCwOQUwwi3b/GIHW9Ik92eAB2C8AoNf1GZW3
NBb8mwFi7bZgANICyG7v
=65r/
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 5.14-rc3 to resolve a bunch of tiny
problems reported. Included in here are:
- dtsi revert to resolve a problem which broke android systems that
relied on the dts name to find the USB controller device.
People are still working out the "real" solution for this, but for
now the revert is needed.
- core USB fix for pipe calculation found by syzbot
- typec fixes
- gadget driver fixes
- new usb-serial device ids
- new USB quirks
- xhci fixes
- usb hub fixes for power management issues reported
- other tiny fixes
All have been in linux-next with no reported problems"
* tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
Revert "USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem"
usb: cdc-wdm: fix build error when CONFIG_WWAN_CORE is not set
Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"
usb: dwc2: gadget: Fix sending zero length packet in DDMA mode.
usb: dwc2: Skip clock gating on Samsung SoCs
usb: renesas_usbhs: Fix superfluous irqs happen after usb_pkt_pop()
usb: dwc2: gadget: Fix GOUTNAK flow for Slave mode.
usb: phy: Fix page fault from usb_phy_uevent
usb: xhci: avoid renesas_usb_fw.mem when it's unusable
usb: gadget: u_serial: remove WARN_ON on null port
usb: dwc3: avoid NULL access of usb_gadget_driver
usb: max-3421: Prevent corruption of freed memory
usb: gadget: Fix Unbalanced pm_runtime_enable in tegra_xudc_probe
MAINTAINERS: repair reference in USB IP DRIVER FOR HISILICON KIRIN 970
usb: typec: stusb160x: Don't block probing of consumer of "connector" nodes
usb: typec: stusb160x: register role switch before interrupt registration
USB: usb-storage: Add LaCie Rugged USB3-FW to IGNORE_UAS
usb: ehci: Prevent missed ehci interrupts with edge-triggered MSI
usb: hub: Disable USB 3 device initiated lpm if exit latency is too high
...
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a7 ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Change all 10G port modes in Armada family device trees from
10gbase-kr to 10gbase-r
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Marvell reference platform CN9130-CRB is a small form factor
board in a metal case. The platform is based on CN9130 SoC with
addition of 8 Gigabit ports SOHO Ethernet switch.
The reference platform features the following:
* Up to 4 CPU cores ARMv8 Cortex-A72 CPU
* CPU core operating speed of up to 2.2GHz
* DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz.
* 1x eMMC 8GB device
* 1x uSD card 4 bits port on CP
* 1x 128MB SPI NOR flash memory
* 1x USB 3.0 Host port (Type A)
* 1x SATA Gen3 via M.2
* 1x USB 3.0 via M.2
* 1x SIM card slot
* 1x 1G Ethernet port via RGMII
* 1x 10G switch port over SFP+ connector
* 8x 1G ports through 88E6393X switch via XFI
* 1x 2.5G/1G/100M/10M port via HS_SGMII
* 1x PCI Express (PCIe)x1 Gen 3.0
* 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2
* JTAG port
The CRB board uses MCP23017 i2c pin controller that drives the
onboard eMMC abd USB 3,0 port power lines.
The following configuration should be enabled for this controller
support:
CONFIG_PINCTRL_MCP23S08=y
The plaform supports two HW configurations - "A" and "B"
CN9130-CRB-A
* AP-MPP configuration: SDIO, UART
* CP0 Serdes configuration:
* Lane0-3: NVMe (PCIe x4)
* Lane4: XFI
* Lane5: HS_SGMII
2. CN9130-CRB-B
* AP-MPP configuration: SDIO, UART
* CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI
* CP0 Serdes configuration:
* Lane0: PCIe x1
* Lane1: USB3_0 x1
* Lane2: SATA x1
* Lane3: USB3_1 x1
* Lane4: XFI
* Lane5: HS_SGMII
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch enables eth0 10G interface on CN9130-DB paltforms and
eth0 10G and eth3 10G interfaces on CN9131-DB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The CN913x DB with topology B is similar to a regular setup (A)
boards, but uses NAND flash as a boot device, while topology A
boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they
cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the
CP0 NAND controller enabled and CP0 SPI1 disabled.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
1) Fix type of bind option flag in af_xdp, from Baruch Siach.
2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao.
3) PM refcnt imbakance in r8152, from Takashi Iwai.
4) Sign extension ug in liquidio, from Colin Ian King.
5) Mising range check in s390 bpf jit, from Colin Ian King.
6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan.
7) Fix skb page recycling race, from Ilias Apalodimas.
8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin.
9) netrom timer sk refcnt issues, from Nguyen Dinh Phi.
10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric
Dumazet.
11) act_skbmod should only operate on ethernet packets, from Peilin Ye.
12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo
Abeni.
13) Fix sparx5 dependencies, from Yajun Deng.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
dpaa2-switch: seed the buffer pool after allocating the swp
net: sched: cls_api: Fix the the wrong parameter
net: sparx5: fix unmet dependencies warning
net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
net: dsa: ensure linearized SKBs in case of tail taggers
ravb: Remove extra TAB
ravb: Fix a typo in comment
net: dsa: sja1105: make VID 4095 a bridge VLAN too
tcp: disable TFO blackhole logic by default
sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set
net: ixp46x: fix ptp build failure
ibmvnic: Remove the proper scrq flush
selftests: net: add ESP-in-UDP PMTU test
udp: check encap socket in __udp_lib_err
sctp: update active_key for asoc when old key is being replaced
r8169: Avoid duplicate sysfs entry creation error
ixgbe: Fix packet corruption due to missing DMA sync
Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"
ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions
fsl/fman: Add fibre support
...
This reverts commit eb9b7bfd59 as it
breaks working userspace implementations (i.e. Android systems)
The device node name here is part of configfs, so it is a user-visable
api that can not be changed.
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/CALAqxLX_FNvFndEDWtGbFPjSzuAbfqxQE07diBJFZtftwEJX5A@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
-----BEGIN PGP SIGNATURE-----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=x8Eo
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
This patch changs interrupt order which found by dtbs_check.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:0: 'macirq' was expected
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:1: 'eth_wake_irq' was expected
According to Documentation/devicetree/bindings/net/snps,dwmac.yaml, we
should list interrupt in it's order.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SC7280 SoC supports a 4-Silver/3-Gold/1-Gold+ configuration and hence
the cpu7 node should point to cpufreq domain 2 instead.
Fixes: 7dbd121a2c ("arm64: dts: qcom: sc7280: Add cpufreq hw node")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1626800953-613-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Define the reserved memory space used for IPA firmware for the
Qualcomm SC7180 SoC.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPA-related nodes and definitions to "sc7280.dtsi", including
the reserved memory area used for AP-based IPA firmware loading.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SA8155p adp board has two USB A-type receptacles called
USB-portB and USB-portC respectively.
While USB-portB is a USB High-Speed connector/interface, the
USB-portC one is a USB 3.1 Super-Speed connector/interface.
Also the USB-portB is used as the USB emergency
download port (for image download purposes).
Enable both the ports on the board in USB Host mode (since all
the USB interfaces are brought out to USB Type A
connectors).
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210627114616.717101-4-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Nodes should be sorted by address, so move the dc_noc and gem_noc nodes
to their correct place.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210627114616.717101-3-bhupesh.sharma@linaro.org
[bjorn: Adjusted order slightly more]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The dwc3 usb nodes in several arm64 qcom dts are currently named
differently, somewhere as 'usb@<addr>' and somewhere as 'dwc3@<addr>',
leading to some confusion when one sees the entries in sysfs or
dmesg:
[ 1.943482] dwc3 a600000.usb: Adding to iommu group 1
[ 2.266127] dwc3 a800000.dwc3: Adding to iommu group 2
Name the usb nodes as 'usb@<addr>' for consistency, which is
the correct convention as per the 'snps,dwc3' dt-binding as
well (see [1]).
[1]. Documentation/devicetree/bindings/usb/snps,dwc3.yaml
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210627114616.717101-2-bhupesh.sharma@linaro.org
[bjorn: Extended to also fix ipq6018]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for UFS ICE (Qualcomm Inline Crypto Engine) in
sm8150 SoC dts.
I tested this on SA8155p-adp board, which is a publicly
available development board that uses the sa8155p Qualcomm
Snapdragon SoC. SA8155p platform is similar to the SM8150,
so use this as base for now.
I tested the UFS ICE feature using 'fscrypt' test utility.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Eric Biggers <ebiggers@google.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210706133814.621536-1-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
cont_splash_mem has different memory mapping than generic from msm8994.dtsi:
[ 0.000000] cma: Found cont_splash_mem@0, memory base 0x0000000003400000, size 12 MiB, limit 0xffffffffffffffff
[ 0.000000] cma: CMA: reserved 12 MiB at 0x0000000003400000 for cont_splash_mem
This fixes boot.
Fixes: 976d321f32 ("arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20210713185734.380-3-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bullhead firmware obviously doesn't support PSCI as it fails to boot
with this definition.
Fixes: 329e16d5f8 ("arm64: dts: qcom: msm8992: Add PSCI support.")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Link: https://lore.kernel.org/r/20210713185734.380-2-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Set audu wakeup delay to 80 ms for fixing pop noise during capture begin.
Fixes: ba5f9b5d7f ("arm64: dts: qcom: sc7180: Add wakeup delay for adau codec")
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210708090810.174767-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has an InvenSense MPU-6880 supported by the
inv_mpu6050 driver in Linux. Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has a notification LED connected to an Awinic
AW2013 controller, add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has a FocalTech touchscreen. The exact model is
not mentioned anywhere, but it works just fine with the mainline
edt-ft5x06 driver when using the "edt,edt-ft5506" compatible.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 is a MSM8916 smartphone that was made by Wingtech
(codename: wt88047). It's fairly similar to the other MSM8916 devices.
The device tree contains initial support for the Xiaomi Redmi 2 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
Note that the Xiaomi Redmi 2 is available in variants with different
names (e.g. Redmi 2 Prime, Redmi 2 Pro, ...). As far as I know the main
difference between those is the amount of RAM and supported LTE bands.
This difference is automatically handled by bootloader/modem firmware
so there is no need for separate device trees.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add OPP tables to scale DDR and L3 with CPUs for SM8150 SoCs.
This gives a significant performance boost for cpu-ddr loads.
Below is the results for mbw benchmark with and without the opp tables.
/mbw 1500
Without l3/ddr scaling With l3 ddr/scaling
MEMCPY(MiB/s) 3574 10448
DUMB(MiB/s) 3500 11721
MCBLOCK(MiB/s) 8976 23595
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20210714182610.92972-1-thara.gopinath@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch changs interrupt order which found by dtbs_check.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:0: 'macirq' was expected
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:1: 'eth_wake_irq' was expected
According to Documentation/devicetree/bindings/net/snps,dwmac.yaml, we
should list interrupt in it's order.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WSA881x powerdown pin is connected to GPIO1, GPIO2 not GPIO2 and GPIO3,
so correct this. This was working so far due to a shift bug in gpio driver,
however once that is fixed this will stop working, so fix this!
For some reason we forgot to add this dts change in last merge cycle so
currently audio is broken in 5.13 as the gpio driver fix already landed
in 5.13.
Reported-by: Shawn Guo <shawnguo@kernel.org>
Fixes: 45021d35fc ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210706083523.10601-1-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "max-clock" and "min-vrefresh" properties fail to validate with
commit cfe34bb7a7 ("dt-bindings: drm: bridge: adi,adv7511.txt:
convert to yaml"). Drop them, as they are parts of an out-of-tree
workaround that is not needed upstream.
Fixes: bcf3003438 ("arm64: dts: renesas: r8a77995: draak: Enable HDMI display output")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/975b6686bc423421b147d367fe7fb9a0db99c5af.1625134398.git.geert+renesas@glider.be
The IN3R is connected to an analog microphone, and it needs the
micbias enabled in order to power the analog microphone.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210630175935.189454-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the Hardware User's Manual, automatic transmission for PMIC
control (DVFS) is not available" on the R-Car E3 SoC. Experiments
showed this really means that support for automatic DVFS is not present,
while the IIC automatic transmission feature itself is still available,
albeit not super useful.
Hence there is no longer a reason not to declare compatibility with the
R-Car Gen3-specific and generic versions. Accordingly, extend the reg
property to cover the automatic transmission registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7b68629350213ca8d37286a6ae6e1966f9958bb8.1624013699.git.geert+renesas@glider.be
According to the Hardware User's Manual, automatic transmission for PMIC
control (DVFS) is not available" on the RZ/G2E SoC. This really means
that support for automatic DVFS is not present, while the IIC automatic
transmission feature itself is still available, albeit not super useful.
Hence there is no longer a reason not to declare compatibility with the
R-Car Gen3-specific and generic versions. Accordingly, extend the reg
property to cover the automatic transmission registers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d222c2faa63f95d672efa07e55e8d01bddd17e65.1624013699.git.geert+renesas@glider.be
Move the parts related to the fourth USB2 interface on Salvator-XS
boards to salvator-xs.dtsi, to avoid future duplication of board
descriptions.
As this interface is not present on all SoCs that can be found on
Salvator-X(S), but only on R-Car H3 ES2.0+, its descriptions are
protected by the preprocessor symbol SOC_HAS_USB2_CH3, defined in
r8a77951.dtsi, and undefined in r8a77950.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/411df1adfd64ee82e5a0d1603df85d657fd4f8c0.1623087028.git.geert+renesas@glider.be
Move the common parts related to the third USB2 interface on
Salvator-X(S) boards to salvator-common.dtsi, to reduce current and
avoid future duplication of board descriptions.
As this interface is not present on all SoCs that can be found on
Salvator-X(S), but only on R-Car H3, its descriptions are protected by
the preprocessor symbol SOC_HAS_USB2_CH2, defined in r8a77951.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/ebc434502fc899b1f9d9640f560c3eaab6bb0927.1623087028.git.geert+renesas@glider.be
Move the common parts related to the SATA interface on Salvator-X(S)
boards to salvator-common.dtsi and salvator-xs.dtsi, to reduce current
and avoid future duplication of board descriptions.
As this interface is not present on all SoCs that can be found on
Salvator-X(S), but only on R-Car H3 and M3-N, its descriptions are
protected by the preprocessor symbol SOC_HAS_SATA, defined in
r8a77951.dtsi and r8a77965.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/87f91290ec7b523aa508e920a169ecaddccc9144.1623087028.git.geert+renesas@glider.be
Move the common parts related to the second HDMI interface on
Salvator-X(S) boards to salvator-common.dtsi, to reduce current and
avoid future duplication of board descriptions.
As this interface is not present on all SoCs that can be found on
Salvator-X(S), but only on R-Car H3, its description are protected by
the preprocessor symbol SOC_HAS_HDMI1, defined in r8a77951.dtsi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/a1d9dcd481d36e5b6e78934e587f6391022030b5.1623087028.git.geert+renesas@glider.be
As of commit c7289b1c8a ("arm64: tegra: Enable SMMU support on
Tegra194"), SMMU support is enabled system-wide on Tegra194. However,
there was a bit of overlap between the SMMU enablement and the PCIe
support addition, so the PCIe device tree nodes are missing the iommus
and interconnects properties. This in turn leads to SMMU faults for
these devices, since by default the ARM SMMU will fault.
Add the iommus and interconnects properties to all the PCIe device
tree nodes to restore their functionality.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This contains two late fixes for Tegra194 device tree files to restore
USB and audio functionality after enabling system-wide IOMMU support.
-----BEGIN PGP SIGNATURE-----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=Tf9G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmDx8qQACgkQmmx57+YA
GNksVA/5AWQ3YeujrzClQHZ9LcWrgK2E8smm0MMS3y9bHUWWx4pXzmm8Z6iUQC61
XL/alTK1Eum+G+hQv12YgbwXc0BAta4clhHc0kOBTEsjUecZy6hk/NqrCC2NQ8Jo
ZUWeHWvbU6+3wlQdb4gFLeMgNRA/vUiHCXdHFC1buh7vUVIxL359QAv6B3AKK5Qk
VFAggSJe+zQEXSKAVlpZa37OPBq/mnkIcjK5ckUJjLA79kw+HMcA6/W5m3P6yJgm
A9YwGgDj360YbEk8R6BG7zDnqYRLk8Fa/9PX54u+n6bdZxTcKEFXQynkTplrstab
jbs3ZLpHUDkSye6Sq3e2W+0nInKOkm//3XUH0ew5wzmAYB3QVDF7cdfs0qxl1wES
kDEXhS4Uy39vImMoq0BeDbH53IAWywtI0aduu7+pphiYDRzoxNkbGaHawMxRcNgp
9Q6qwF+RG9SS0QDnucdRS108S9pjxcLr663blF0njJuZWfR4qNX5uG72fq99i/5n
EIN4VQPCHMvojGCXH6wFhnhEaMjeLVohika49QX/O4Mwu40ma8F4b57xwGgOPyxP
5H8yX0evulfGeZ/d9o8hR2Ztexp4wPnrN6rxUCZo2VKoCSJHBmm7uclsrFE5qxgX
eS6xU8PGSg8KBiq3Q4tOS5wjRLGKZjtn0E2EXwcmM2MfPP855+Q=
=aeU2
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc1
This contains two late fixes for Tegra194 device tree files to restore
USB and audio functionality after enabling system-wide IOMMU support.
* tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for USB on Tegra194
arm64: tegra: Enable audio IOMMU support on Tegra194
Link: https://lore.kernel.org/r/20210709150220.2543875-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add CPU caches information to its dt nodes so that the same is available
to userspace via sysfs. This SoC has 48/32 KB I/D cache for each A57
cores with 2MB L2 cache. And 32/32 KB I/D cache for each A53 cores with
256KB L2 cache.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210622130551.67446-2-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add CPU caches information to its dt nodes so that the same is available
to userspace via sysfs. This SoC has 48/32 KB I/D cache
for each cores and 2MB of L2 cache.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210622130551.67446-1-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This adds a basic devicetree for the MNT Reform2 DIY laptop. Not all
of the board periperals are enabled yet, as some of them still require
kernel patches to work properly. The nodes for those peripherals will
be added as soon as the required patches are upstream.
The following has been tested to work:
- UART console
- SD card
- eMMC
- Gigabit Ethernet
- USB (internal Keyboard, Mouse, external ports)
- M.2 PCIe port
Co-developed-by: Lukas F. Hartmann <lukas@mntre.com>
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the description of the Nitrogen8 System on Module. The module
is quite simple with only a few (almost) fixed regulators and a eMMC
on-board.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like always, the DT branch is sizable. There are numerous additions and
fixes to existing platforms, but also a handful of new ones introduced.
Less than some other releases, but there's been significant work on
cleanups, refactorings and device enabling on existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and 5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs, and
new support for Microsoft Surface Duo (SM8150-based), Huawei Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and NanoPi
R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added
-----BEGIN PGP SIGNATURE-----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=X6PF
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Olof Johansson:
"Like always, the DT branch is sizable. There are numerous additions
and fixes to existing platforms, but also a handful of new ones
introduced. Less than some other releases, but there's been
significant work on cleanups, refactorings and device enabling on
existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the
Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for
rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and
5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc
definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs,
and new support for Microsoft Surface Duo (SM8150-based), Huawei
Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and
NanoPi R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added"
* tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (511 commits)
arm64: dts: rockchip: add basic dts for RK3568 EVB
arm64: dts: rockchip: add core dtsi for RK3568 SoC
arm64: dts: rockchip: add generic pinconfig settings used by most Rockchip socs
ARM: dts: rockchip: add vpu and vdec node for RK322x
ARM: dts: rockchip: add vpu nodes for RK3066 and RK3188
ARM: dts: rockchip: add vpu node for RK3036
arm64: dts: ipq8074: Add QUP6 I2C node
arm64: dts: rockchip: Re-add regulator-always-on for vcc_sdio for rk3399-roc-pc
arm64: dts: rockchip: Re-add regulator-boot-on, regulator-always-on for vdd_gpu on rk3399-roc-pc
arm64: dts: rockchip: add ir-receiver for rk3399-roc-pc
arm64: dts: rockchip: Add USB-C port details for rk3399 Firefly
arm64: dts: rockchip: Sort rk3399 firefly pinmux entries
arm64: dts: rockchip: add infrared receiver node to RK3399 Firefly
arm64: dts: rockchip: add SPDIF node for rk3399-firefly
arm64: dts: rockchip: Add Rotation Property for OGA Panel
arm64: dts: qcom: sc7180: bus votes for eMMC and SD card
arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen
arm64: dts: qcom: sm8250-edo: Enable GPI DMA
arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI
arm64: dts: qcom: sm8250-edo: Enable PCIe
...
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
As of commit c7289b1c8a ("arm64: tegra: Enable SMMU support on
Tegra194"), SMMU support is enabled system-wide on Tegra194. However,
there was a bit of overlap between the SMMU enablement and the USB
support addition, so the USB device tree nodes are missing the iommus
and interconnects properties. This in turn leads to SMMU faults for
these devices, since by default the ARM SMMU will fault.
Add the iommus and interconnects properties to the XUSB and XUDC device
tree nodes to restore their functionality.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add iommus and interconnects properties to the sound device tree node on
Tegra194. This ensures that the correct SID is used for translation of
physical to I/O virtual addresses and that the path to system memory is
properly described, which in turn can impact the range of memory that
the device can address.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Including:
- SMMU Updates from Will Deacon:
- SMMUv3: Support stalling faults for platform devices
- SMMUv3: Decrease defaults sizes for the event and PRI queues
- SMMUv2: Support for a new '->probe_finalize' hook, needed by Nvidia
- SMMUv2: Even more Qualcomm compatible strings
- SMMUv2: Avoid Adreno TTBR1 quirk for DB820C platform
- Intel VT-d updates from Lu Baolu:
- Convert Intel IOMMU to use sva_lib helpers in iommu core
- ftrace and debugfs supports for page fault handling
- Support asynchronous nested capabilities
- Various misc cleanups
- Support for new VIOT ACPI table to make the VirtIO IOMMU:
available on x86
- Add the amd_iommu=force_enable command line option to
enable the IOMMU on platforms where they are known to cause
problems
- Support for version 2 of the Rockchip IOMMU
- Various smaller fixes, cleanups and refactorings
-----BEGIN PGP SIGNATURE-----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=IxNB
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- SMMU Updates from Will Deacon:
- SMMUv3:
- Support stalling faults for platform devices
- Decrease defaults sizes for the event and PRI queues
- SMMUv2:
- Support for a new '->probe_finalize' hook, needed by Nvidia
- Even more Qualcomm compatible strings
- Avoid Adreno TTBR1 quirk for DB820C platform
- Intel VT-d updates from Lu Baolu:
- Convert Intel IOMMU to use sva_lib helpers in iommu core
- ftrace and debugfs supports for page fault handling
- Support asynchronous nested capabilities
- Various misc cleanups
- Support for new VIOT ACPI table to make the VirtIO IOMMU
available on x86
- Add the amd_iommu=force_enable command line option to enable
the IOMMU on platforms where they are known to cause problems
- Support for version 2 of the Rockchip IOMMU
- Various smaller fixes, cleanups and refactorings
* tag 'iommu-updates-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (66 commits)
iommu/virtio: Enable x86 support
iommu/dma: Pass address limit rather than size to iommu_setup_dma_ops()
ACPI: Add driver for the VIOT table
ACPI: Move IOMMU setup code out of IORT
ACPI: arm64: Move DMA setup operations out of IORT
iommu/vt-d: Fix dereference of pointer info before it is null checked
iommu: Update "iommu.strict" documentation
iommu/arm-smmu: Check smmu->impl pointer before dereferencing
iommu/arm-smmu-v3: Remove unnecessary oom message
iommu/arm-smmu: Fix arm_smmu_device refcount leak in address translation
iommu/arm-smmu: Fix arm_smmu_device refcount leak when arm_smmu_rpm_get fails
iommu/vt-d: Fix linker error on 32-bit
iommu/vt-d: No need to typecast
iommu/vt-d: Define counter explicitly as unsigned int
iommu/vt-d: Remove unnecessary braces
iommu/vt-d: Removed unused iommu_count in dmar domain
iommu/vt-d: Use bitfields for DMAR capabilities
iommu/vt-d: Use DEVICE_ATTR_RO macro
iommu/vt-d: Fix out-bounds-warning in intel/svm.c
iommu/vt-d: Add PRQ handling latency sampling
...
UART1 (standard variant with DT node name 'uart0') has register space
0x12000-0x12018 and not whole size 0x200. So fix also this in example.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: c737abc193 ("arm64: dts: marvell: Fix A37xx UART0 register size")
Link: https://lore.kernel.org/r/20210624224909.6350-6-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This provides the configuration for the currently available evaluation
boards PCB134 and PCB135.
The series depends on the following series currently on its way
into the kernel:
- Sparx5 Reset Driver
Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a series of refactorings and additions to the SM8150 and SM8250
platform definitions, this adds new devicetree definitions for Sony
Xperia 1, 5, 1II and 5II.
It defines the Qualcomm SA8155p automotive platform as a derrivative of
SM8150 and introduces the Automotive Deveopment Platform board.
Lastly ipq8074 gains the definiton of an additiona I2C master and the
SDHCI bus votes for sc7180 are tweaked.
-----BEGIN PGP SIGNATURE-----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=5AxZ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=e35Z
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Additional Qualcomm ARM64 DT updates for v5.14
After a series of refactorings and additions to the SM8150 and SM8250
platform definitions, this adds new devicetree definitions for Sony
Xperia 1, 5, 1II and 5II.
It defines the Qualcomm SA8155p automotive platform as a derrivative of
SM8150 and introduces the Automotive Deveopment Platform board.
Lastly ipq8074 gains the definiton of an additiona I2C master and the
SDHCI bus votes for sc7180 are tweaked.
* tag 'qcom-arm64-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (25 commits)
arm64: dts: ipq8074: Add QUP6 I2C node
arm64: dts: qcom: sc7180: bus votes for eMMC and SD card
arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen
arm64: dts: qcom: sm8250-edo: Enable GPI DMA
arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI
arm64: dts: qcom: sm8250-edo: Enable PCIe
arm64: dts: qcom: sm8250: Commonize PCIe pins
arm64: dts: qcom: sm8250-edo: Add hardware keys
arm64: dts: qcom: sa8155p-adp: Add base dts file
arm64: dts: qcom: pmm8155au_2: Add base dts file
arm64: dts: qcom: pmm8155au_1: Add base dts file
arm64: dts: qcom: sm8250-edo: Fix up double "pinctrl-1"
arm64: dts: qcom: sm8[12]50-pm8150: Move RESIN to pm8150 dtsi
arm64: dts: qcom: sm8250: Add support for SONY Xperia 1 II / 5 II (Edo platform)
arm64: dts: qcom: sm8250: Move gpio.h inclusion to SoC DTSI
arm64: dts: qcom: sm8250: Add SDHCI2 sleep mode pinctrl
arm64: dts: qcom: sm8150: Add support for SONY Xperia 1 / 5 (Kumano platform)
arm64: dts: qcom: sm8150: Disable Adreno and modem by default
arm64: dts: qcom: sm8250: Disable Adreno and Venus by default
arm64: dts: qcom: sm8250: Add GPI DMA nodes
...
Link: https://lore.kernel.org/r/20210621164946.942956-1-bjorn.andersson@linaro.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Display rotation and audio codec for the Odroid Go Advance;
IR, spdif and usb-c support for rk3399-firefly;
USB support for rk3308 and some rk3328 boards and setting
the PCIe link speed to actually only supported speed on rk3399.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmDO/cEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdge1jB/9YUxCy4YUpdu6Cd1xMSekFi9fk5fHb/KF/
OboLWvgany7SW0zAGV6XgFxIZKczVx5kQwq1Sf0seiI5u7RL2Fir5VRh9Uu6qK0l
i8saw+hThXWu4Bg3xiKo8eIG76apHAH9eWuSuRx9hJjb6PgOym5Fh2IOcdUyx7JB
g3TqUGk/Ai+TR55ySPB6f/TJQO0PFNMmzrJO0QYnO70TWFRYKsmsnLCEfAPpzcr0
1NBbvLF+mtvNOlTlANUDAr4XcqrMJgGI7b4s3i0c8Dt5ani6QoJKuwZvnKbG7Tm5
zOgiHnDfNcHMacTeJKwDUKc/zF+Dvt+fflsfk1thb+tFHbuEXIQT
=H1p3
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=qhsN
-----END PGP SIGNATURE-----
Merge tag 'v5.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot of dt-yaml related fixes; PCIe, USB and pwm-fans for Helios64;
Display rotation and audio codec for the Odroid Go Advance;
IR, spdif and usb-c support for rk3399-firefly;
USB support for rk3308 and some rk3328 boards and setting
the PCIe link speed to actually only supported speed on rk3399.
* tag 'v5.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (30 commits)
arm64: dts: rockchip: Re-add regulator-always-on for vcc_sdio for rk3399-roc-pc
arm64: dts: rockchip: Re-add regulator-boot-on, regulator-always-on for vdd_gpu on rk3399-roc-pc
arm64: dts: rockchip: add ir-receiver for rk3399-roc-pc
arm64: dts: rockchip: Add USB-C port details for rk3399 Firefly
arm64: dts: rockchip: Sort rk3399 firefly pinmux entries
arm64: dts: rockchip: add infrared receiver node to RK3399 Firefly
arm64: dts: rockchip: add SPDIF node for rk3399-firefly
arm64: dts: rockchip: Add Rotation Property for OGA Panel
arm64: dts: rockchip: Add support for USB on helios64
arm64: dts: rockchip: add USB support to rk3308.dtsi
arm64: dts: rockchip: rename nodename for phy-rockchip-inno-usb2
arm64: dts: rockchip: add rk817 codec to Odroid Go
arm64: dts: rename grf-gpio nodename in rk3328.dtsi
arm64: dts: rockchip: Add support for PCIe on helios64
arm64: dts: rockchip: Add support for two PWM fans on helios64
arm64: dts: rockchip: fix regulator-gpio states array
arm64: dts: rockchip: add #power-domain-cells to power domain nodes
arm64: dts: rockchip: Fix power-controller node names for rk3399
arm64: dts: rockchip: Fix power-controller node names for rk3328
arm64: dts: rockchip: Fix power-controller node names for px30
...
Link: https://lore.kernel.org/r/2796982.e9J7NaK4W3@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
on Armada 3700:
Move turris-mox-rwtm firmware node to a more generic place
on AP807:
Make SD/MMC controller still usbale with older kernel
CP11x:
update comphy references
cn9130:
Improve NAND partitioning scheme for cn9130-db
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCYM8AuAAKCRALBhiOFHI7
1WiaAJ9bSDRCWpkWEnJS/i867xL2QHrDMACgjJlDVRyyuBbqC8ltQGTZSYAHxuk=
=qTZO
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=fpYE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.14 (part 1)
on Armada 3700:
Move turris-mox-rwtm firmware node to a more generic place
on AP807:
Make SD/MMC controller still usbale with older kernel
CP11x:
update comphy references
cn9130:
Improve NAND partitioning scheme for cn9130-db
* tag 'mvebu-dt64-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
Documentation/bindings: phy: update references to cp11x
arm64: dts: ensure backward compatibility of the AP807 Xenon
arm64: dts: marvell: armada-37xx: move firmware node to generic dtsi file
Link: https://lore.kernel.org/r/878s3429zi.fsf@BL-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
RK3568 is a high-performance and low power quad-core application processor
designed for personal mobile internet device and AIoT equipment. This patch
add basic core dtsi file for it.
We use scmi_clk for cortex-a55 instead of standard ARMCLK, so that
kernel/uboot/rtos can change cpu clk with the same code in ATF, and we will
enalbe a special high-performance PLL when high frequency is required. The
smci_clk code is in ATF, and clkid for cpu is 0, as below:
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a55";
reg = <0x0 0x0>;
clocks = <&scmi_clk 0>;
};
Signed-off-by: Liang Chen <cl@rock-chips.com>
Link: https://lore.kernel.org/r/20210622020517.13100-4-cl@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pinconfig settings for Rockchip SoCs are pretty similar on all socs,
so move them to a shared dtsi to be included, instead of redefining them
for each soc.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Link: https://lore.kernel.org/r/20210622020517.13100-3-cl@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add node to support the QUP6 I2C controller inside
of IPQ8074.
It is exactly the same as QUP2 and QUP3 controllers.
Some routers like Xiaomi AX9000 and Netgear RBK850
use this bus.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20210619162751.2336974-1-robimarko@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Re-add the regulator-always-on property for vcc_sdio which supplies sdmmc,
since it gets disabled during reboot now and the bootrom expects it to be
enabled when booting from SD card. This makes rebooting impossible in that
case and requires a hard reset to boot again.
Fixes: 04a0077fdb ("arm64: dts: rockchip: Remove always-on properties from regulator nodes on rk3399-roc-pc.")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210619121306.7740-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This might be a limitation of either the current panfrost driver
devfreq implementation or how the gpu is implemented in RK3399 SoC.
The gpu regulator must never get disabled or the registers get
(randomly?) inaccessable by the driver. (see all other RK3399 boards)
Fixes: ec7d731d81 ("arm64: dts: rockchip: Add node for gpu on rk3399-roc-pc")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210619121446.7802-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Like some other RK3399 boards RK3399-ROC-PC has an ir receiver
connected to pwm3 which can be used as gpio-ir-receiver.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210619121642.7892-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enabling the hardware thankfully comes down to a simple status = "okay".
We assume that the firmware is provided by the Linux distribution, as it's
signed and needs to come from the stock Android.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616122708.144770-4-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commonize PCIe pins, as the configuration is SoC-common
and doesn't change (or at least doesn't change much) between
boards.
While at it, remove "output-low" from the RB5 board, as it's
not necessary - we already explicitly pull the perst pin low.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616122708.144770-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Volume Down, GAssist (pdx206 only) and camera keys live on PMIC pins,
with the latter kind being broken for now.. Add these and PON-connected
Volume Up & PWR.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616122708.144770-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add base DTS file for SA8155p Automotive Development Platform.
It enables boot to console, adds tlmm reserved range and ufs flash.
It also includes pmic file.
SA8155p-adp board is based on sa8155p Qualcomm Snapdragon SoC.
SA8155p platform is similar to the SM8150, so use this as base
for now.
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210617054548.353293-6-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Two carveout reserved memory nodes each have been added for each of the
R5F remote processor devices within the MAIN domain on the TI AM642 EVM
and SK boards. These nodes are assigned to the respective rproc device
nodes as well. The first region will be used as the DMA pool for the rproc
devices, and the second region will furnish the static carveout regions
for the firmware memory.
An additional reserved memory node is also added to reserve a portion of
the DDR memory to be used for performing inter-processor communication
between all the remote processors running RTOS or baremetal firmwares.
8 MB of memory is reserved for this purpose, and this accounts for all
the vrings and vring buffers between all the possible pairs of remote
processors.
The current carveout addresses and sizes are defined statically for each
rproc device. The R5F processors do not have an MMU, and as such require
the exact memory used by the firmwares to be set-aside. The firmware
images do not require any RSC_CARVEOUT entries in their resource tables
to allocate the memory for firmware memory segments.
NOTE:
1. The R5F1 carveouts are needed only if the R5F cluster is running in
Split (non Single-CPU) mode. The reserved memory nodes can be disabled
later on if there is no use-case defined to use the corresponding
remote processor.
2. The AM64x SoCs do not have any DSPs and one less R5F cluster compared
to J721E SoCs. So, while the carveout memories reserved for the R5F
clusters present on the SoC match to those on J721E, the overall
memory map reserved for firmwares is quite different. The number of
R5F clusters on AM64x SoCs are same as on J7200 SoCs, but the AM64x
SoCs also have an additional M4F core, so the RTOS IPC memory region
is 1 MB higher than on J7200 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210615195718.15898-4-s-anna@ti.com
Add the required 'mboxes' property to all the R5F processors for the
TI AM642 EVM and SK boards. The mailboxes and some shared memory are
required for running the Remote Processor Messaging (RPMsg) stack
between the host processor and each of the R5Fs.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Note that any R5F Core1 resources are needed and used only when that
R5F cluster is configured for Split-mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210615195718.15898-3-s-anna@ti.com
The AM64x SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. Both the R5F clusters are present within the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a new "Single-CPU" mode
or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
The mode is restricted to "Single-CPU" on some devices with the
appropriate eFuse bit set, but the most common devices support both
modes. These subsystems have 64 KB each Tightly-Coupled Memory (TCM)
internal memories for each core split between two banks - ATCM and
BTCM (further interleaved into two banks). The TCMs of both Cores
are combined in Single-CPU mode to provide a larger 128 KB of memory.
The other notable difference is that the TCMs are spaced 1 MB apart
on these SoCs unlike the existing SoCs.
Add the DT nodes for both these MAIN domain R5F cluster/subsystems,
the two R5F cores are added as child nodes to each of the corresponding
R5F cluster node. Both the clusters are configured to run in Split mode
by default, with the ATCMs enabled to allow the R5 cores to execute
code from DDR with boot-strapping code from ATCM. The inter-processor
communication between the main A72 cores and these processors is
achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
MAIN R5FSS0 Core0: am64-main-r5f0_0-fw (both in Single-CPU & Split modes)
MAIN R5FSS0 Core1: am64-main-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS1 Core0: am64-main-r5f1_0-fw (both in Single-CPU & Split modes)
MAIN R5FSS1 Core1: am64-main-r5f1_1-fw (needed only in Split mode)
NOTE:
A R5FSS cluster can be configured in "Single-CPU" mode by using a
value of 2 for the "ti,cluster-mode" property. Value of 1 is not
permitted (fails the dtbs_check).
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210615195718.15898-2-s-anna@ti.com
When bringing the SDC pins back to edo.dtsi I managed to define
and overwrite pinctrl-1 instead of defining pinctrl-0 and 1. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616161536.206044-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Eliminate 1MB gap between Linux and filesystem partitions.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
A recent switch to a dedicated AP807 compatible string for the Xenon
SD/MMC controller result in the driver not being probed when
using updated device tree with the older kernel revisions.
It may also be problematic for other OSs/firmware that use
Linux device tree sources as a reference. Resolve the problem
with backward compatibility by restoring a previous compatible
string as secondary one.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Move the turris-mox-rwtm firmware node from Turris MOX' device tree into
the generic armada-37xx.dtsi file and use the generic compatible string
'marvell,armada-3700-rwtm-firmware' instead of the current one.
Turris MOX DTS file contains also old compatible string for backward
compatibility.
The Turris MOX rWTM firmware can be used on any Armada 37xx device,
giving them access to the rWTM hardware random number generator, which
is otherwise unavailable.
This change allows Linux to load the turris-mox-rwtm.ko module on these
boards.
Tested on ESPRESSObin v5 with both default Marvell WTMI firmware and
CZ.NIC's firmware. With default WTMI firmware the turris-mox-rwtm fails
to probe, while with CZ.NIC's firmware it registers the HW random number
generator.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
s/Hisilicon/HiSilicon/.
It should use capital S, according to the official website
https://www.hisilicon.com/en.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Due to a limitation for USB DFU boot mode, SPL load address has to be less
than or equal to 0x70001000. So, load address of SPL and TF-A have been
moved to 0x70000000 and 0x701c0000 respectively, in U-Boot version 2021.10.
Therefore, update TF-A's location in the device tree node.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210616171224.24635-4-a-govindraju@ti.com
The final 128KB in SRAM is reserved by default for DMSC-lite code and
secure proxy communication buffer. The memory region used for DMSC-lite
code can be optionally freed up by secure firmware API[1]. However, the
buffer for secure proxy communication is not configurable. This default
hardware configuration is unique for AM64.
Therefore, indicate the area reserved for DMSC-lite code and secure proxy
communication buffer in the oc_sram device tree node.
[1] - http://downloads.ti.com/tisci/esd/latest/6_topic_user_guides/security_handover.html#triggering-security-handover
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210616171224.24635-3-a-govindraju@ti.com
It's not worth duplicating the same node over and over and over and over again,
so let's keep the common bits in the pm8150 DTSI, making only changing the
status and keycode necessary.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613124822.124039-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for SONY Xperia 1 II and 5 II smartphones (read one/five mark two).
They are based on the Qualcomm SM8250 chipset and both feature 5G modems. There
also exists a third Edo board, namely the Xperia PRO (PDX204), but it's $2500
and no developers have obtained it so far (to my knowledge).
The devices are affected by a scary UFS behaviour where sending a certain UFS
command (which is worked around on downstream) renders the device unbootable,
by effectively erasing the bootloader. Therefore UFS AND UFSPHY are strictly
disabled for now.
Downstream workaround:
2e7a9ee1c9
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616002321.74155-4-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Almost any board that boots and has a way to interact with it
(say for the rare cases of just-pstore or let's-rely-on-bootloader-setup)
needs to set some GPIOs, so it makes no sense to include gpio.h separately
each time. Hence move it to SoC DTSI.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616002321.74155-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add required pins for SDHCI2, so that the interface can work reliably.
This commit adds sleep_state setup to the SoC DTSI, as it is common for
all boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210616002321.74155-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for SONY Xperia 1 and 5 smartphones, both based on the
Qualcomm SM8150 chipset. There also exist 5G-capable versions of these
devices, but they weren't sold much (if at all) outside Japan.
The devices are affected by a scary UFS behaviour where sending a certain UFS
command (which is worked around on downstream) renders the device unbootable,
by effectively erasing the bootloader. Therefore UFS AND UFSPHY are strictly
disabled for now.
Downstream workaround:
2e7a9ee1c9
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> (On Bahamut)
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210611203301.101067-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Not enabling modem back on the HDK, as it uses a sa8150.
Also fixed a sorting mistake in both boards' dt while at it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210611203301.101067-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210612192358.62602-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the aforementioned properties in the SoC DTSI so that everybody doesn't
have to copy that into their device DTs, effectively reducing code
duplication.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613114356.82358-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DPU/MDSS is borderline useless without MDP, so disabling
both of them makes little sense. With this change, enabling
mdss will be enough.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613110635.46537-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Contains changes to consolidate audio card names, adds audio support on
Jetson Xavier NX and enables SMMU on Tegra194.
-----BEGIN PGP SIGNATURE-----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=A6hi
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.14-rc1
Contains changes to consolidate audio card names, adds audio support on
Jetson Xavier NX and enables SMMU on Tegra194.
* tag 'tegra-for-5.14-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support on Tegra194
arm64: tegra: Hook up memory controller to SMMU on Tegra186
arm64: tegra: Use correct compatible string for Tegra186 SMMU
arm64: tegra: Audio graph sound card for Jetson Xavier NX
arm64: tegra: Consolidate audio card names
arm64: tegra: Add PMU node for Tegra194
Link: https://lore.kernel.org/r/20210611164437.3568059-6-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add DT support for Toshiba Visconti5 PWM driver
-----BEGIN PGP SIGNATURE-----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=1GK5
-----END PGP SIGNATURE-----
Merge tag 'visconti-arm-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti into arm/dt
Visconti device tree updates for 5.14
- Add DT support for Toshiba Visconti5 PWM driver
* tag 'visconti-arm-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti:
arm64: dts: visconti: Add PWM support for TMPV7708 SoC
Link: https://lore.kernel.org/r/20210614234654.2u3xetnn5rwhymwz@toshiba.co.jp
Signed-off-by: Olof Johansson <olof@lixom.net>
MSM8916 gains new support for Huawei Ascend G7, with NFC, sensors and
touchscreen. The Samsung Galaxy A3/A5 gains battery support, touch keys,
NFC.
MSM8996 received more cleanup and refactoring, preparing for upcoming
new devices. Note worthy is the long pending enablement of CPUfreq.
SC7180 continues to stabilize, with a range of small fixes for various
bits and pieces, and new revisions for the CoachZ and pompom devices.
SC7280 continues to grow, with more clock controllers, thermal sensors,
thermal zones, CPUfreq and interconnect providers.
Xiaomi Poco F1 gaines audio support and the OnePlus 6/6T gaines IPA
support.
SM8350 gains some cleanups and the IPA device is enabled.
Initial support for the Microsoft Surface Duo, based on SM8150, is
added.
IPQ8074 gained support for the HK10 board.
-----BEGIN PGP SIGNATURE-----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=Pj6c
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.14
MSM8916 gains new support for Huawei Ascend G7, with NFC, sensors and
touchscreen. The Samsung Galaxy A3/A5 gains battery support, touch keys,
NFC.
MSM8996 received more cleanup and refactoring, preparing for upcoming
new devices. Note worthy is the long pending enablement of CPUfreq.
SC7180 continues to stabilize, with a range of small fixes for various
bits and pieces, and new revisions for the CoachZ and pompom devices.
SC7280 continues to grow, with more clock controllers, thermal sensors,
thermal zones, CPUfreq and interconnect providers.
Xiaomi Poco F1 gaines audio support and the OnePlus 6/6T gaines IPA
support.
SM8350 gains some cleanups and the IPA device is enabled.
Initial support for the Microsoft Surface Duo, based on SM8150, is
added.
IPQ8074 gained support for the HK10 board.
* tag 'qcom-arm64-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (85 commits)
arm64: dts: qcom: sc7180: Add xo clock for eMMC and Sd card
arm64: dts: sc7280: Add interconnect provider DT nodes
arm64: dts: qcom: msm8916-huawei-g7: Add NFC
arm64: dts: qcom: msm8916-huawei-g7: Add display regulator
arm64: dts: qcom: msm8916-huawei-g7: Add sensors
arm64: dts: qcom: msm8916-huawei-g7: Add touchscreen
arm64: dts: qcom: msm8916: Add device tree for Huawei Ascend G7
arm64: dts: qcom: sc7180-trogdor: Update flash freq to match reality
arm64: dts: qcom: sc7180: Add wakeup delay for adau codec
arm64: dts: qcom: sdm845: Remove cros-pd-update on Cheza
arm64: dts: qcom: sc7180: Remove cros-pd-update on Trogdor
arm64: dts: qcom: sc7180: Disable PON on Trogdor
arm64: dts: qcom: sc7180: Modify SPI_CLK voltage level for trogdor
arm64: dts: qcom: add initial device-tree for Microsoft Surface Duo
arm64: dts: qcom: sdm845-mtp: enable IPA
arm64: dts: qcom: sc7180: SD-card GPIO pin set bias-pull up
arm64: dts: qcom: sc7180: Move sdc pinconf to board specific DT files
arm64: dts: qcom: msm8916-samsung-a2015: Add NFC
arm64: dts: qcom: msm8916-samsung-a2015: Add rt5033 battery
arm64: dts: qcom: msm8916-samsung-a5u: Add touch key regulator
...
Link: https://lore.kernel.org/r/20210614223712.393096-1-bjorn.andersson@linaro.org
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: i.MX8MM Gateworks GW7901 board.
- Add SPBA bus description for i.MX8MN and i.MX8MM.
- A series of update on imx8mq-nitrogen board to add USB OTG/Host and
LT8912 MIPI-DSI to HDMI support.
- Correct enet clock description for i.MX8 Connection Subsystem.
- A couple of patches from Heiko Schocher to add FlexSPI device for
i.MX8MP SoC and enable SPI NOR Flash support on imx8mp-phycore-som.
- Remove the reference to audio IPG clock on i.MX8MP.
- Enable EQOS Ethernet and PMIC device support for imx8mp-evk.
- Disable USB over-current on imx8mm-evk and imx8mn-evk.
- Add dma-ranges description for i.MX8MM and i.MX8MN SoC.
- Add PCIe clock description for i.MX8MQ SoC.
- Enable PCIe support on freeway board.
- Enable OPTEE support on ls1028a-rdb board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmDFvn4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5v7Qf/QbcMDnuc3phG9SvVY2HYRhJwQqr+
Fj6bXtPZAtk6knPjdhuxhtbLqDbZoDaJGOYaZE2itJpSfMIRZHgk5gb+fz4caZvC
ZS4nefLmjAlyctlVaDpDwUGQVis+7BfwnsY7HVqbbqJDXjC0bNL0iQvcvIKjDDdg
aXirBcpZvRtdkXvXG2QdUZJmTjnLnDKe9oM6AP6Ernami5n3yX7VT9AyJfKQoEra
9A6Y+sGol65W8S2qVcpPxWfSSoiRHSKKuSlOHpeRaIALRCz0WgyIvvB1NsY1lTBt
VkhLq5ySI+AnHJwvBUn6R10cV8Lx4rUOi3Q4EtH/Sg7dtiK+UKKa2YmTxg==
=seFj
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree chagnes for 5.14:
- New board support: i.MX8MM Gateworks GW7901 board.
- Add SPBA bus description for i.MX8MN and i.MX8MM.
- A series of update on imx8mq-nitrogen board to add USB OTG/Host and
LT8912 MIPI-DSI to HDMI support.
- Correct enet clock description for i.MX8 Connection Subsystem.
- A couple of patches from Heiko Schocher to add FlexSPI device for
i.MX8MP SoC and enable SPI NOR Flash support on imx8mp-phycore-som.
- Remove the reference to audio IPG clock on i.MX8MP.
- Enable EQOS Ethernet and PMIC device support for imx8mp-evk.
- Disable USB over-current on imx8mm-evk and imx8mn-evk.
- Add dma-ranges description for i.MX8MM and i.MX8MN SoC.
- Add PCIe clock description for i.MX8MQ SoC.
- Enable PCIe support on freeway board.
- Enable OPTEE support on ls1028a-rdb board.
* tag 'imx-dt64-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
arm64: dts: imx8mn-evk: disable over current for usb
arm64: dts: imx8mm-evk: disable over current for usb1
arm64: dts: freescale: Separate each group of data in the property 'reg'
arm64: dts: imx8: conn: fix enet clock setting
arm64: dts: imx8mq: assign PCIe clocks
arm64: dts: imx8mn: specify dma-ranges
arm64: dts: imx8mm: specify dma-ranges
arm64: dts: fsl-ls1028a: Correct ECAM PCIE window ranges
arm64: dts: imx8mn-beacon-som: Assign PMIC clock
arm64: dts: ls208xa: remove bus-num from dspi node
arm64: dts: ls1012a: enable PCIe on freeway board
arm64: dts: imx8mp-evk: enable EQOS ethernet
arm64: dts: imx8mp: Remove the reference to audio ipg clock on imx8mp
arm64: dts: imx8mq-evk: add one regulator used to power up pcie phy
arm64: dts: imx8mm: Add spba1 and spba2 buses
arm64: dts: imx8mn: Add spba1 bus
arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI
arm64: dts: imx8mq-nitrogen: add USB HOST support
arm64: dts: imx8mq-nitrogen: add USB OTG support
arm64: dts: imx8mp-phycore-som: enable spi nor
...
Link: https://lore.kernel.org/r/20210613082544.16067-5-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The calculations for the DLL register values are based on the clock rate
of the reference clock. Provide the reference clock in the definition of
the two SDHCI controllers to not rely on the default values.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Link: https://lore.kernel.org/r/1623309107-27833-1-git-send-email-sbhanu@codeaurora.org
[bjorn: Rewrote commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
8250_omap compatible UART IPs on all SoCs have registers aligned at 4
byte address boundary and constant byte addressability. Thus there is no
need for reg-io-width or reg-shift DT properties. These properties are
not used by 8250_omap driver nor documented as part of binding document.
Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210607134558.23704-1-vigneshr@ti.com
ti,pindir-d0-out-d1-in property is expected to be of type boolean.
Therefore, fix the property accordingly.
Fixes: 4fb6c04683 ("arm64: dts: ti: k3-am642-evm: Add support for SPI EEPROM")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210608051414.14873-3-a-govindraju@ti.com
The current device tree CPSW3g node adds non-zero "mac-address" property to
the ports, which prevents random MAC address assignment to network devices
if bootloader failed to update DT. This may cause more then one host to
have the same MAC in the network.
mac-address = [00 00 de ad be ef];
mac-address = [00 01 de ad be ef];
In addition, there is one MAC address available in eFuse registers which
can be used for default port 1.
Hence, fix ports MAC properties by:
- resetting "mac-address" property to 0
- adding ti,syscon-efuse = <&main_conf 0x200> to Port 1
Fixes: 3753b12877 ("arm64: dts: ti: k3-am64-main: Add CPSW DT node")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210608184940.25934-1-grygorii.strashko@ti.com
Drop the hub_5v regulator which controls the HUB Reset line with GPIOH_4 which
is already controlled by a GPIO HOG.
Until we can properly describe how to control USB HUBs reset lines, keeping
the GPIO HOG is an acceptable solution we use on multiple boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-8-narmstrong@baylibre.com
Add a node for the XT25F128B SPI-NOR flash to make it accessible
from Linux.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-7-narmstrong@baylibre.com
As described in the HC4 schematics, GPIOH_8 controls the USB 5V and 12V
regulators used to power the SATA drives.
And is set as Open Drain since this GPIO doesn't support Push-Pull.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-6-narmstrong@baylibre.com
As described in the HC4 schematics, only the USB port B is used,
port A is left unconnected. Thus disable PHY0 and remove it from PHYs list.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-5-narmstrong@baylibre.com
As described in the Odroid-C4 & Odroid-HC4 schematics, the 5V regulator is controlled
by GPIOH_8 and in Open Drain since this GPIO doesn't support Push-Pull.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-4-narmstrong@baylibre.com
According to Odroid-C4 & HC4 Schematics, the TF_3V3N_1V8_EN can be in Hi-Z for 3v3,
and since it's the default GPIOAO_6 mode at reset, let switch this GPIO as Open-Source
to drive for 1, and input for 0.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-3-narmstrong@baylibre.com
As described in the schematics of Odroid-C4 and Odroid-HC4, the TF_IO regulator
is enabled by the GPIOE_2 GPIO and gets it's supply from VCC_5V.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210607065435.577334-2-narmstrong@baylibre.com
There are 3 additional patches pending that handle the backward
compatiblity inside the PCI subsystem, but the address ranges
should be fixed anyway.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmDD4CsQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSjiB/4j2bmuvwwsB7ZRQjtjpmFNl+eGCeiXZTPL
ex8TEOMsG7ra+xMDF5ElbfLi8PnHu3VIZxCRLbU3r/15NRHY/Z34P59TDsW8WeQS
eVaSa87JlWxFL2JH/CSDGgPSY3jG33kk0cCf4a+FXFjMkaSNAUaXwpvCBio0MQG1
T5QnqEpV91Iej/BMXqyljst2LZNlYsN+vT4BGv4uaqUb6EPSOTSm1xJ60kbPPvE6
ylaqP/tUfL3u8hC1u0vrc2MWZh+Y/0EPyHvmLBEkTvOROTNOdNGiGvTfs5Gce2eu
Bzyzkn4Cp8d/UioGCpyKeXwcBYe47UlM1J28GTXUY3D+TKrjGhKy
=SSkm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fix PCIe address ranges that are affected by recent PCI changes.
There are 3 additional patches pending that handle the backward
compatiblity inside the PCI subsystem, but the address ranges
should be fixed anyway.
* tag 'v5.13-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
Link: https://lore.kernel.org/r/3405741.0S5aU1g85B@diego
Signed-off-by: Olof Johansson <olof@lixom.net>
mainly:
- I2S Support for the V3
- Audio Codec Support for the V3s
- DMA support for the V3s
- PWM support for the V3s
- Support for Bluetooth Audio on the pinephone
- Add A10-like timers to the A64 and R40
- New boards: Forlinx OKA40i-C, Forlinx OKA40i-C, NanoPi R1S H5
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYMN5hwAKCRDj7w1vZxhR
xa2sAP0Y4UY9ncxWmuTUMgi4osqscowxGUsCHdfxP+Yk9/IJ8wEAqKA5tfior25d
guy+cgXft/CixRtgv6Go3W55tJpZ6wQ=
=A9Cb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to improve the Allwinner SoCs support,
mainly:
- I2S Support for the V3
- Audio Codec Support for the V3s
- DMA support for the V3s
- PWM support for the V3s
- Support for Bluetooth Audio on the pinephone
- Add A10-like timers to the A64 and R40
- New boards: Forlinx OKA40i-C, Forlinx OKA40i-C, NanoPi R1S H5
* tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (29 commits)
ARM: dts: sun8i: v3s: enable emac for zero Dock
arm64: dts: allwinner: pinephone: Set audio card name
ARM: dts: sun8i: r40: Add timer node
ARM: dts: sun8i: V3: add I2S interface to V3 dts
dt-bindings: sound: sun4i-i2s: add Allwinner V3 I2S compatible
ARM: dts: sun8i: V3: add codec analog frontend to V3 dts
ASoC: dt-bindings: sun8i-a23-codec-analog: add compatible for Allwinner V3
ARM: dts: sun8i: v3s: add analog codec and frontend to v3s dts
ARM: dts: sun8i: v3s: add DMA properties to peripherals supporting DMA
ARM: dts: sun8i: v3s: add DMA controller to v3s dts
ARM: dts: sun8i: v3s: add pwm controller to v3s dts
dt-bindings: pwm: allwinner: add v3s pwm compatible
arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
dt-bindings: arm: Add NanoPi R1S H5
arm64: dts: allwinner: pinephone: Add support for Bluetooth audio
arm64: dts: allwinner: a64: Allow multiple DAI links
arm64: dts: allwinner: a64: Add pinmux nodes for AIF2/AIF3
arm64: dts: allwinner: a64: Allow using multiple codec DAIs
ARM: dts: sun8i-a33: Allow using multiple codec DAIs
ASoC: dt-bindings: sun8i-codec: Increase #sound-dai-cells
...
Link: https://lore.kernel.org/r/96cc77ec-139d-4685-8a66-a60964cf39fd.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
Just a single fix to use standard and generic nodes names for SCMI
power domain controller and clock controller devicetree nodes.
-----BEGIN PGP SIGNATURE-----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=36FY
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno fix for v5.14
Just a single fix to use standard and generic nodes names for SCMI
power domain controller and clock controller devicetree nodes.
* tag 'juno-fix-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Update SCPI nodes as per the YAML schema
Link: https://lore.kernel.org/r/20210611075805.2813712-1-sudeep.holla@arm.com
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Zhen fixes the Broadcom stingray serial node unit names to fix a DT
binding warning
-----BEGIN PGP SIGNATURE-----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=6wtT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.14/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs changes for 5.14,
please pull the following:
- Zhen fixes the Broadcom stingray serial node unit names to fix a DT
binding warning
* tag 'arm-soc/for-5.14/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: normalize the node name of the UART devices
Link: https://lore.kernel.org/r/20210610194836.309869-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.14, please pull the following:
- Rafal updates the BCM5301x, HR2, BCM63xx, BCM5301x, NSP and Cygnus DTS
files to resolve a number of DT binding check warnings pertaining to
NAND, pinmux, clocks, SPI
- Stefan provides a fix for an increase in the DWC2 controller's RX FIFO
causing regressions on the Raspberry Pi 4B
- Mateusz adds a BCM2711 specific VEC compatible string to allow keying
off that variant properly
- Stefan adds support for the Raspberry Pi 400 by doing some DTS/DTSI
re-organization work and finally adding the DTS file proper
-----BEGIN PGP SIGNATURE-----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=ZmMv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.14/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.14, please pull the following:
- Rafal updates the BCM5301x, HR2, BCM63xx, BCM5301x, NSP and Cygnus DTS
files to resolve a number of DT binding check warnings pertaining to
NAND, pinmux, clocks, SPI
- Stefan provides a fix for an increase in the DWC2 controller's RX FIFO
causing regressions on the Raspberry Pi 4B
- Mateusz adds a BCM2711 specific VEC compatible string to allow keying
off that variant properly
- Stefan adds support for the Raspberry Pi 400 by doing some DTS/DTSI
re-organization work and finally adding the DTS file proper
* tag 'arm-soc/for-5.14/devicetree' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: Add reference to RPi 400
ARM: dts: Add Raspberry Pi 400 support
ARM: dts: bcm283x: Fix up GPIO LED node names
dt-bindings: arm: bcm2835: Add Raspberry Pi 400 to DT schema
ARM: dts: Move BCM2711 RPi specific into separate dtsi
ARM: dts: bcm283x: Fix up MMC node names
ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible
Revert "ARM: dts: bcm283x: increase dwc2's RX FIFO size"
ARM: dts: BCM5301X: Fixup SPI binding
dt-bindings: clock: brcm, iproc-clocks: convert to the json-schema
ARM: dts: BCM5301X: Fix pinmux subnodes names
ARM: dts: Hurricane 2: Fix NAND nodes names
ARM: dts: BCM63xx: Fix NAND nodes names
ARM: NSP: dts: fix NAND nodes names
ARM: Cygnus: dts: fix NAND nodes names
ARM: brcmstb: dts: fix NAND nodes names
ARM: dts: BCM5301X: Fix NAND nodes names
Link: https://lore.kernel.org/r/20210610194836.309869-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
imx8mn evk board usb port does not support over current detection,
so disable it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm evk board usb1 port does not support over current detection,
so disable it.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not write the 'reg' of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported by reg.yaml.
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml:
soc: pcie@3400000:reg:0: \
[0, 54525952, 0, 1048576, 64, 0, 0, 8192] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
enet_clk_ref actually is sourced from internal gpr clocks
which needs a default rate. Also update enet lpcg clock
output names to be more straightforward.
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DMA addressing capabilities on i.MX8MN are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DMA addressing capabilities on i.MX8MM are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently all PCIE windows point to bus address 0x0, which does not match
the values obtained from hardware during EA.
Replace those values with CPU addresses, since in reality we
have a 1:1 mapping between the two.
Signed-off-by: Kornel Duleba <mindal@semihalf.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c3 ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1012a-freeway board contains a M.2 2230 slot. Update the status of
pcei1 node to okay so that the pcie controller can be probed.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MP, there is no audio ipg clock, so remove the wrong reference
to this clock in dts file.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MM reference manual shows there are two spba busses.
SPBA1 handles much of the serial interfaces, and SPBA2 covers much
of the audio.
Add both of them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MN has an SPBA bus which covers much of the audio, but
there is a second SPBA bus which covers many of the serial interfaces
like SPI and UARTs currently missing from the device tree. The reference
manual calls the bus handling the audio peripherals SPBA2, and the bus
handling the serial peripherals is called SPBA1.
Rename the existing spba bus to spba2 and add spba1.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support of the lt8912b in the DTB.
This adds the support of the DB_DSIHD daugther board from
Boundary Devices.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the description for the USB host port.
This port is linked to a resettable USB HUB so handle
this reset signal with a GPIO hog.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the description for the USB OTG port.
The OTG port uses a dedicated regulator for vbus.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PCIe host bridge on RK3399 advertises a single 64-bit memory
address range even though it lies entirely below 4GB.
Previously the OF PCI range parser treated 64-bit ranges more
leniently (i.e., as 32-bit), but since commit 9d57e61bf7 ("of/pci:
Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")
the code takes a stricter view and treats the ranges as advertised in
the device tree (i.e, as 64-bit).
The change in behaviour causes failure when allocating bus addresses
to devices connected behind a PCI-to-PCI bridge that require
non-prefetchable memory ranges. The allocation failure was observed
for certain Samsung NVMe drives connected to RockPro64 boards.
Update the host bridge window attributes to treat it as 32-bit address
memory. This fixes the allocation failure observed since commit
9d57e61bf7.
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/7a1e2ebc-f7d8-8431-d844-41a9c36a8911@arm.com
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20210607112856.3499682-5-punitagrawal@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Putting the panel under the bridge chip (under the aux-bus node)
allows the panel driver to get access to the DP AUX bus, enabling all
sorts of fabulous new features.
While we're at this, get rid of a level of hierarchy for the panel
node. It doesn't need "ports / port" and can just have a "port" child.
For Linux, this patch has a hard requirement on the patches adding DP
AUX bus support to the ti-sn65dsi86 bridge chip driver. See the patch
("drm/bridge: ti-sn65dsi86: Add support for the DP AUX bus").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210611101711.v10.11.Ibdb7735fb1844561b902252215a69526a14f9abd@changeid
Add the device tree node for the dual-SMMU found on Tegra194 and hook up
peripherals such as host1x, BPMP, HDA, SDMMC, EQOS and VIC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the memory controller needs to be programmed in
coordination with any of the ARM SMMU instances to configure the stream
ID used for each memory client.
To support this, add a phandle reference to the memory controller to the
SMMU device tree node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SMMU found on Tegra186 requires interoperation with the memory
controller in order to program stream ID overrides. The generic ARM SMMU
500 compatible is therefore inaccurate. Replace it with a more correct,
SoC-specific compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the DT nodes for the network-on-chip interconnect buses found
on sc7280-based platforms.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-4-git-send-email-okukatla@codeaurora.org
[bjorn: Sorted nodes and dropped include]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 supports NFC using the NXP PN547, which is
supported by the nxp-nci-i2c driver in mainline. It seems to detect
NFC tags using "nfctool" just fine, although it seems like there
are not really any useful applications making use of the Linux NFC
subsystem. :(
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The display on the Huawei Ascend G7 is supplied by a TI TPS65132
regulator. The panel needs a driver in mainline first, but the
TPS65132 is already supported in mainline by the tps65132 driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 has a Synaptics "C199HW-006" touchscreen,
supplied by pm8916_l17 and pm8916_l16. Add it to the device tree
and reduce the maximum allowed voltage for pm8916_l16 to 1.8V since
we really should not use more for an I/O supply.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916.
It's fairly similar to the other MSM8916 devices, the only notable
exception are the "cd-gpios" for detecting if a SD card was inserted:
It looks like Huawei forgot to re-route this to gpio38, so the correct
GPIO seems to be gpio56 on this device.
Note: The original firmware from Huawei can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei
forgot to set up (firmware) secure boot for some reason.
Also note that Huawei no longer provides bootloader unlock codes.
This can be bypassed by patching the bootloader from a custom HYP firmware,
making it think the bootloader is unlocked. I use a modified version of
qhypstub [1], that patches a single instruction in the Huawei bootloader.
The device tree contains initial support for the Huawei Ascend G7 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Notification LED (combination of 3 GPIO LEDs)
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
[1]: https://github.com/msm8916-mainline/qhypstub
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This spi flash part is actually being clocked at 37.5MHz, not 25MHz,
because of the way the clk driver is rounding up the rate that is
requested to the nearest supported frequency. Let's update the frequency
here, and remove the TODO because this is the fastest frequency we're
going to be able to use here.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210519054030.3217704-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-2-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the PON module on Trogdor devices. Instead the reboot
reason is sort of stored in the 'eventlog' and the bootloader figures
out if the boot is abnormal and records that there. Disable the PON node
and then drop the power key disabling because that's a child node that
will no longer be enabled if the PON node is disabled.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601184417.3020834-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add initial DTSI for RZ/G2{L,LC} SoC's.
File structure:
r9a07g044.dtsi => RZ/G2L family SoC common parts
r9a07g044l1.dtsi => RZ/G2L R9A07G044L1 SoC specific parts
r9a07g044l2.dtsi => RZ/G2L R9A07G044L2 SoC specific parts
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Although the schematics of Pine A64-LTS and SoPine Baseboard shows both
the RX and TX internal delay are enabled, they're using the same broken
RTL8211E chip batch with Pine A64+, so they should use TXID instead, not
ID.
In addition, by checking the real components soldered on both a SoPine
Baseboard and a Pine A64-LTS, RX delay is not enabled (GR69 soldered and
GR70 NC) despite the schematics says it's enabled. It's a common
situation for Pine64 boards that the NC information on schematics is not
the same with the board.
So the RGMII delay mode should be TXID on these boards.
Fixes: c2b111e59a ("arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210609083843.463750-1-icenowy@aosc.io
Add a basic GPU node for mt8183, as well as OPP table.
Note that with the current panfrost driver, devfreq is not
actually functional, as the we do not have platform-specific
support for >1 supplies. Also, we are missing code to handle
frequency change, as the GPU frequency needs to be switched
away to a stable 26Mhz clock during the transition.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210521200038.v14.1.I9f45f5c1f975422d58b5904d11546349e9ccdc94@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located
on PCB board to correlate the temperature of the case (Tskin).
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
AuxIn = Vsense * 4096 / 1500
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210604093755.13288-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a 'cbas' device node for supporting tablet mode switch in
kukui devices.
Kukui platforms with detacheable base have an additional input
device under cros-ec, which reports SW_TABLET_MODE regarding
its base state (e.g. base flipped or detached).
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210609032554.2443675-1-ikjn@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds a reference to the dts of the Raspberry Pi 400,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/1622981777-5023-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
AM642-SK has no PCIe slot. Disable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-6-kishon@ti.com
AM642 EVM has a x4 lane PCIe connector. Enable PCIe in RC mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-4-kishon@ti.com
AM64 has one PCIe instance which can be configured in either
host mode (RC) or device mode (EP). Add PCIe DT node for host
mode and device mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-3-kishon@ti.com
AM64 has one SERDES 10G instance. Add SERDES DT node for it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-2-kishon@ti.com
Commit 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board:
Configure the PCIe instances") and
commit 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed
support for USB0") added PHY DT nodes with node name as "link"
However nodes with #phy-cells should be named 'phy' as discussed in [1].
Re-name subnodes of serdes in J721E to 'phy'.
[1] -> http://lore.kernel.org/r/20200909203631.GA3026331@bogus
Fixes: 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board: Configure the PCIe instances")
Fixes: 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-5-kishon@ti.com
Use external clock for all the SERDES used by PCIe controller. This will
make the same clock used by the local SERDES as well as the clock
provided to the PCIe connector.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-4-kishon@ti.com
Add #clock-cells property to serdes DT node since the serdes is also now
modeled as a clock provider and include the input clocks "pll0_refclk"
and "pll1_refclk" which are parents to the clocks modeled by serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-3-kishon@ti.com
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe6 ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
Enable support for audio-graph based sound card on Jetson Xavier NX.
Following I/O interfaces are enabled.
- I2S3 and I2S5
- DMIC1, DMIC2 and DMIC4
- DSPK1 and DSPK2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This enables the adreno-specific SMMU path that sets HUPCF so
(user-managed) page faults don't wedge the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-2-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
The ICSSGs on K3 J721E SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-j721e-main.dtsi
file by default, and disabled in the existing J721E board dts
file. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-3-s-anna@ti.com
The ICSSGs on K3 AM65x SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-am65-main.dtsi
file by default, and disabled in the existing AM65 board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[s-anna@ti.com: move the disabled status to board dts files]
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-2-s-anna@ti.com
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
the common iot2050 device tree file.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210529033749.6250-1-a-govindraju@ti.com
"make dtbs_check":
arm64/boot/dts/renesas/r8a779a0-falcon.dt.yaml: interrupt-controller@f1000000: 'power-domains' does not match any of the regexes: '^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$', '^gic-its@', '^interrupt-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Remove the "power-domains" property, as the GIC on R-Car V3U is
always-on, and not part of a clock domain.
Fixes: 834c310f54 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/a9ae5cbc7c586bf2c6b18ddc665ad7051bd1d206.1622560236.git.geert+renesas@glider.be
Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210603122923.1919624-1-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some SC7180 based boards do not have external pull-up for cd-gpio.
Set this pin to internal pull-up for sleep config to avoid frequent
regulator toggle events.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.2.I52f30ddfe62041b7e6c3c362f0ad8f695ac28224@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have a Samsung S3FWRN5 NFC chip that
works quite well with the s3fwrn5 driver in the Linux NFC subsystem.
The clock setup for the NFC chip is a bit special (although this
seems to be a common approach used for Qualcomm devices with NFC):
The NFC chip has an output GPIO that is asserted whenever the clock
is needed to function properly. On the A3/A5 this is wired up to
PM8916 GPIO2, which is then configured with a special function
(NFC_CLK_REQ or BB_CLK2_REQ).
Enabling the rpmcc RPM_SMD_BB_CLK2_PIN clock will then instruct
PM8916 to automatically enable the clock whenever the NFC chip
requests it. The advantage is that the clock is only enabled when
needed and we don't need to manage it ourselves from the NFC driver.
Note that for some reason Samsung decided to connect the I2C pins
to GPIOs where no hardware I2C bus is available, so we need to
fall back to software bit-banging with i2c-gpio.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 use a Richtek RT5033 PMIC as battery
fuel gauge, charger, flash LED and for some regulators. For now,
only add the fuel gauge/battery device to the device tree,
so we can check the remaining battery percentage.
The other RT5033 drivers need some more work first before
they can be used properly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On the Samsung Galaxy A5 the touch key is supplied by a single fixed
regulator (enabled via GPIO 97) that supplies both MCU and LED.
Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The touch key MCU and LED is supplied by two separate fixed regulators
that can be enabled through GPIO 86 and 60. Add them to the device tree.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
[stephan: extend commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have two capacitive touch keys,
connected to an ABOV MCU. It implements the same interface as
implemented by the tm2-touchkey driver and works just fine with
the coreriver,tc360-touchkey compatible. It's probably actually some
Samsung-specific interface that they implement with different MCUs.
Note that for some reason Samsung decided to connect this to GPIOs
where no hardware I2C bus is available, so we need to fall back
to software bit-banging using i2c-gpio.
The vdd/vcc-supply is board-specific and will be added separately
for a3u/a5u.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a thermal zone for the pm6150 on-die temperature. The system should
try to shut down orderly when the temperature reaches the critical trip
point at 115°C, otherwise the PMIC will perform a HW power off at 145°C.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210603081215.v2.1.Id4510e9e4baaa3f6c9fdd5cdf4d8606e63c262e3@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
-----BEGIN PGP SIGNATURE-----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=veTm
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/fixes
Devicetree fixes for TI K3 platforms for v5.13 merge window:
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
* tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
arm64: dts: ti: k3-am65|j721e|am64: Map the dma / navigator subsystem via explicit ranges
arm64: dts: ti: k3-*: Rename the TI-SCI node
arm64: dts: ti: k3-am65-wakeup: Drop un-necessary properties from dmsc node
arm64: dts: ti: k3-am65-wakeup: Add debug region to TI-SCI node
arm64: dts: ti: k3-*: Rename the TI-SCI clocks node name
arm64: dts: ti: j7200-main: Mark Main NAVSS as dma-coherent
arm64: dts: ti: k3-am654-base-board: remove ov5640
Link: https://lore.kernel.org/r/20210518115634.467vgpbzplal5kou@obituary
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmCu8p4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7k+Qf9Ek/atJBjaaVzhbGFQ8HRnDOk4U5J
dR0GbXKSN1zXjDLSBOBRyNcVn2T6lp4LwwYoleC2qG6MNoe6+y7fk1oRdvjkGjRO
ZYfZT/JJl187IN6JsxR8VhRmmcI5/C3bihMbpKoLdHcPGbwC4relfSy99Io94Xfk
CVn3PTxBA4KfoDq/+EiA9HkQ/HwQh/y7KD5yVd6OtLkt9awT1hYW1ttVefp95nAK
5+zTm0Z14U8aGm+wo8jywvSyeXiuMeWDUrweo05XcaHWfcv3T0Wni7tgS2pluxqa
lCMsNQBsZDTk6fUWxqPjjAEl6ks8N1H9L7YIGpq1dOCSYFUqI3jCmkhrFQ==
=5vQk
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.13:
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
* tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
ARM: dts: imx6q-dhcom: Add PU,VDD1P1,VDD2P5 regulators
ARM: dts: imx6dl-yapp4: Fix RGMII connection to QCA8334 switch
Link: https://lore.kernel.org/r/20210527011758.GD8194@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
The Rockchip RK3308 features an integrated USB 2.0 phy, an USB OTG
controller and OHCI/EHCI interfaces.
This patch adds all of those to the RK3308 dtsi and thereby enables USB
support on the RK3308.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pattern: "^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$"
in phy-provider.yaml has required "#phy-cells" for phy nodes.
The "phy-cells" in rockchip-inno-usb2 nodes are located in subnodes.
Rename the nodename to pattern "usb2phy@[0-9a-f]+$" to prevent
notifications.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the new rk817 codec driver to the Odroid Go Advance.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20210519203754.27184-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We don't need to register smi_common as syscon. Also add required
property power-domains for this node.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601040014.2970805-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Adds label for MI2S secondary block to allow follower projects to override
for the four speaker support which uses I2S SD1 line on gpio52 pin.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20210601022117.4071117-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The first UART controller in "Everything-Else" power domain, usually used
for Bluetooth HCI has 128bytes FIFO depth.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-4-narmstrong@baylibre.com
The sc7280 IDP board is also called senor in the Chrome OS builds.
Add the "google,senor" compatible so coreboot/depthcharge knows what
device tree blob to pick
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1619674827-26650-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210514113430.1.Ic2d032cd80424af229bb95e2c67dd4de1a70cb0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the video, gpu, display, lpass clock controller
device nodes for SC7280 SoC.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1618020280-5470-3-git-send-email-tdas@codeaurora.org
[bjorn: Dropped includes, as they are not present in v5.13-rc1]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ADC and thermal monitor configuration for skin temperature,
plus a thermal zone that monitors the skin temperature and uses
the big cores as cooling devices.
CoachZ rev1 is stuffed with an incompatible thermistor for the
skin temperature, disable the thermal zone for rev1 to avoid
the use of bogus temperature values.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210414111007.v1.1.I1a438604a79025307f177347d45815987b105cb5@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per Dmitry Baryshkov [1]:
a) The 2nd "reg" should be 0x3c because "Offset 0x38 is
USB3_DP_COM_REVISION_ID3 (not used by the current driver though)."
b) The 3rd "reg" "is a serdes region and qmp_v3_dp_serdes_tbl contains
registers 0x148 and 0x154."
I think because the 3rd "reg" is a serdes region we should just use
the same size as the 1st "reg"?
[1] https://lore.kernel.org/r/ee5695bb-a603-0dd5-7a7f-695e919b1af1@linaro.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Fixes: 58fd7ae621 ("arm64: dts: qcom: sc7180: Update dts for DP phy inside QMP phy")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210315103836.1.I9a97120319d43b42353aeac4d348624d60687df7@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use sm8250 compatibles instead of sdm845 compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
