[ Upstream commit 749a401683 ]
The MLX driver was not updating its control virtqueue size at set_vq_num
and instead always initialized to MLX5_CVQ_MAX_ENT (16) at
setup_cvq_vring.
Qemu would try to set the size to 64 by default, however, because the
CVQ size always was initialized to 16, an error would be thrown when
sending >16 control messages (as used-ring entry 17 is initialized to 0).
For example, starting a guest with x-svq=on and then executing the
following command would produce the error below:
# for i in {1..20}; do ifconfig eth0 hw ether XX:xx:XX:xx:XX:XX; done
qemu-system-x86_64: Insufficient written data (0)
[ 435.331223] virtio_net virtio0: Failed to set mac address by vq command.
SIOCSIFHWADDR: Invalid argument
Acked-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <20240216142502.78095-1-jonah.palmer@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Fixes: 5262912ef3 ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f490c492e9 ]
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7db7775ea ]
Commit d3256efd8e ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea80e3ed09 ]
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Link: b40da332df
Fixes: ba37b7caf1 ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b85ef15a ]
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f3082 ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e37ad71b2 ]
Move the setting of the MTK_MAC_MCR register from the end of mac_config
into the phylink mac_finish() method, to keep it as the very last write
that is done during configuration.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: f1b85ef15a ("net: mediatek: mtk_eth_soc: clear MAC_MCR_FORCE_LINK only when MAC is up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ebb41b88 ]
A previous bugfix added a call to kcalloc(), which starting in gcc-14
causes a harmless warning about the argument order:
drivers/soc/fsl/dpio/dpio-service.c: In function 'dpaa2_io_service_enqueue_multiple_desc_fq':
drivers/soc/fsl/dpio/dpio-service.c:526:29: error: 'kcalloc' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
526 | ed = kcalloc(sizeof(struct qbman_eq_desc), 32, GFP_KERNEL);
| ^~~~~~
drivers/soc/fsl/dpio/dpio-service.c:526:29: note: earlier argument should specify number of elements, later size of each element
Since the two are only multiplied, the order does not change the
behavior, so just fix it now to shut up the compiler warning.
Dmity independently came up with the same fix.
Fixes: 5c4a5999b2 ("soc: fsl: dpio: avoid stack usage warning")
Reported-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 367c50f784 ]
Current average steal timer calculation produces volatile and inflated
values. The only user of this value is KVM so far and it uses that to
decide whether or not to yield the vCPU which is seeing steal time.
KVM compares average steal timer to a threshold and if the threshold
is past then it does not allow CPU polling and yields it to host, else
it keeps the CPU by polling.
Since KVM's steal time threshold is very low by default (%10) it most
likely is not effected much by the bloated average steal timer values
because the operating region is pretty small. However there might be
new users in the future who might rely on this number. Fix average
steal timer calculation by changing the formula from:
avg_steal_timer = avg_steal_timer / 2 + steal_timer;
to the following:
avg_steal_timer = (avg_steal_timer + steal_timer) / 2;
This ensures that avg_steal_timer is actually a naive average of steal
timer values. It now closely follows steal timer values but of course
in a smoother manner.
Fixes: 152e9b8676 ("s390/vtime: steal time exponential moving average")
Signed-off-by: Mete Durlu <meted@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e642921dfe ]
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f35c9af45e ]
Later attempts to refault the bo won't happen and the whole
GPU does to lunch. I think Christian's refactoring of this
code out to the driver broke this not very well tested path.
Fixes: 141b15e591 ("drm/nouveau: move io_reserve_lru handling into the driver v5")
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240311072037.287905-1-airlied@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f0974eccb ]
This kind of state is per-syscall, and since we're doing the waiting off
entering the io_uring_enter(2) syscall, there's no way that iowait can
already be set for this case. Simplify it by setting it if we need to,
and always clearing it to 0 when done.
Fixes: 7b72d661f1 ("io_uring: gate iowait schedule on having pending requests")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600556809f ]
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34164202a5 ]
The get_channel_from_mode() function is supposed to return the channel
which matches the mode. But it has a bug where if it doesn't find a
matching channel then it returns the last channel. It should return
NULL instead.
Also remove an unnecessary NULL check on "channel".
Fixes: 2870b52bae ("greybus: lights: add lights implementation")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/379c0cb4-39e0-4293-8a18-c7b1298e5420@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b5a5c00b ]
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 544c42f798 ]
IRQ_DOMAIN is a hidden (not user visible) symbol. Users cannot set
it directly thru "make *config", so drivers should select it instead
of depending on it if they need it.
Relying on it being set for a dependency is risky.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on" for IRQ_DOMAIN to
"select" for RTC_DRV_MT6397.
Fixes: 04d3ba70a3 ("rtc: mt6397: add IRQ domain dependency")
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Eddie Huang <eddie.huang@mediatek.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-rtc@vger.kernel.org
Cc: Marc Zyngier <maz@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Peter Rosin <peda@axentia.se>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240213050258.6167-1-rdunlap@infradead.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af8bbce920 ]
A macro placed at the end of a file with no newline causes an infinite
loop.
[Test Kconfig]
$(info,hello)
\ No newline at end of file
I realized that flex-provided input() returns 0 instead of EOF when it
reaches the end of a file.
Fixes: 104daea149 ("kconfig: reference environment variables directly and remove 'option env='")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27058b95fb ]
Ethernet switch does not have addressable subnodes.
This fixes:
arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dtb: ethernet-switch@0: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/dsa/brcm,sf2.yaml#
Fixes: 527a3ac9bd ("arm64: dts: broadcom: bcm4908: describe internal switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240111115636.12095-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314c2b3992 ]
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ede8c6f47 ]
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6a92f67c ]
The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f87 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
So for sakeness, change to 0x20 (which is SPACE).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 7a99565f87 ("vt: ignore csi sequences with intermediate characters.")
Cc: Martin Hostettler <textshell@uchuujin.de>
Link: https://lore.kernel.org/all/ZaP45QY2WEsDqoxg@neutronstar.dyndns.org/
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c77b35ce66 ]
The sparse tool complains about the remove of the _iomem attribute.
stm32_rproc.c:660:17: warning: cast removes address space '__iomem' of expression
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to addresses pointer,
which are then managed by the remoteproc core as a pointer to a
resource_table structure.
Fixes: 8a471396d2 ("remoteproc: stm32: Move resource table setup to rproc_ops")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20240117135312.3381936-3-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32381bbccb ]
The sparse tool complains about the attribute conversion between
a _iomem void * and a void *:
stm32_rproc.c:122:12: sparse: sparse: incorrect type in assignment (different address spaces) @@ expected void *va @@ got void [noderef] __iomem * @@
stm32_rproc.c:122:12: sparse: expected void *va
stm32_rproc.c:122:12: sparse: got void [noderef] __iomem *
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to virtual addresses pointer,used,
by the remoteproc core.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312150052.HCiNKlqB-lkp@intel.com/
Fixes: 13140de09c ("remoteproc: stm32: add an ST stm32_rproc driver")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20240117135312.3381936-2-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03bd158e15 ]
With CONFIG_ARCH_STM32 making it into arch/arm64, a couple of format
strings no longer work, since they rely on size_t being compatible
with %x, or they print an 'int' using %z:
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_mem_alloc':
drivers/remoteproc/stm32_rproc.c:122:22: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:122:40: note: format string is defined here
122 | dev_dbg(dev, "map memory: %pa+%x\n", &mem->dma, mem->len);
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c:125:30: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:125:65: note: format string is defined here
125 | dev_err(dev, "Unable to map memory region: %pa+%x\n",
| ~^
| |
| unsigned int
| %lx
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_get_loaded_rsc_table':
drivers/remoteproc/stm32_rproc.c:646:30: error: format '%zx' expects argument of type 'size_t', but argument 4 has type 'int' [-Werror=format=]
drivers/remoteproc/stm32_rproc.c:646:66: note: format string is defined here
646 | dev_err(dev, "Unable to map memory region: %pa+%zx\n",
| ~~^
| |
| long unsigned int
| %x
Fix up all three instances to work across architectures, and enable
compile testing for this driver to ensure it builds everywhere.
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Stable-dep-of: 32381bbccb ("remoteproc: stm32: Fix incorrect type in assignment for va")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f53641a6e8 upstream.
The comedi_test devices have a couple of timers (ai_timer and ao_timer)
that can be started to simulate hardware interrupts. Their expiry
functions normally reschedule the timer. The driver code calls either
del_timer_sync() or del_timer() to delete the timers from the queue, but
does not currently prevent the timers from rescheduling themselves so
synchronized deletion may be ineffective.
Add a couple of boolean members (one for each timer: ai_timer_enable and
ao_timer_enable) to the device private data structure to indicate
whether the timers are allowed to reschedule themselves. Set the member
to true when adding the timer to the queue, and to false when deleting
the timer from the queue in the waveform_ai_cancel() and
waveform_ao_cancel() functions.
The del_timer_sync() function is also called from the waveform_detach()
function, but the timer enable members will already be set to false when
that function is called, so no change is needed there.
Fixes: 403fe7f34e ("staging: comedi: comedi_test: fix timer race conditions")
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20240214100747.16203-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0aec3847d0 ]
This reverts commit 57e9d49c54.
This undoes the hiding of .__afsXXXX silly-rename files. The problem with
hiding them is that rm can't then manually delete them.
This also reverts commit 5f7a076466 ("afs: Fix
endless loop in directory parsing") as that's a bugfix for the above.
Fixes: 57e9d49c54 ("afs: Hide silly-rename files from userspace")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Link: https://lists.infradead.org/pipermail/linux-afs/2024-February/008102.html
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/3085695.1710328121@warthog.procyon.org.uk
Reviewed-by: Jeffrey E Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6d721e14 ]
When a file only needs one direct_node, performing the following
operations will cause the file to be unrepairable:
unisoc # ./f2fs_io compress test.apk
unisoc #df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.2M 100% /data
unisoc # ./f2fs_io release_cblocks test.apk
924
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 4.8M 100% /data
unisoc # dd if=/dev/random of=file4 bs=1M count=3
3145728 bytes (3.0 M) copied, 0.025 s, 120 M/s
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
0
This is because the file has only one direct_node. After returning
to -ENOSPC, reserved_blocks += ret will not be executed. As a result,
the reserved_blocks at this time is still 0, which is not the real
number of reserved blocks. Therefore, fsck cannot be set to repair
the file.
After this patch, the fsck flag will be set to fix this problem.
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot then fsck will be executed
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
924
Fixes: c75488fb4d ("f2fs: introduce F2FS_IOC_RESERVE_COMPRESS_BLOCKS")
Signed-off-by: Xiuhong Wang <xiuhong.wang@unisoc.com>
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 698ad1a538 ]
The intent is to check if 'dest' is truncated or not. So, >= should be
used instead of >, because strlcat() returns the length of 'dest' and 'src'
excluding the trailing NULL.
Fixes: 56463e50d1 ("NFS: Use super.c for NFSROOT mount option parsing")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbd7c0088b ]
The driver never sets a default timeout value, therefore it is
initialized to zero. When CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is
enabled, the watchdog is started during probe. The kernel is supposed to
automatically ping the watchdog from this point until userspace takes
over, but this does not happen if the configured timeout is zero. A zero
timeout causes watchdog_need_worker() to return false, so the heartbeat
worker does not run and the system therefore resets soon after the
driver is probed.
This patch fixes this by setting an arbitrary non-zero default timeout.
The default could be read from the hardware instead, but I didn't see
any reason to add this complexity.
This has been tested on an STM32F746.
Fixes: 85fdc63fe2 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240228182723.12855-1-ben.wolsieffer@hefring.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcac8bff90 ]
Switch order of operations to avoid creating a short XDR buffer:
e.g., buflen = 12, old xdrlen = 12, new xdrlen = 20.
Having a short XDR buffer leads to lxa_maxcount be a few bytes
less than what is needed to retrieve the whole list when using
a buflen as returned by a call with size = 0:
buflen = listxattr(path, NULL, 0);
buf = malloc(buflen);
buflen = listxattr(path, buf, buflen);
For a file with one attribute (name = '123456'), the first call
with size = 0 will return buflen = 12 ('user.123456\x00').
The second call with size = 12, sends LISTXATTRS with
lxa_maxcount = 12 + 8 (cookie) + 4 (array count) = 24. The
XDR buffer needs 8 (cookie) + 4 (array count) + 4 (name count)
+ 6 (name len) + 2 (padding) + 4 (eof) = 28 which is 4 bytes
shorter than the lxa_maxcount provided in the call.
Fixes: 04a5da690e ("NFSv4.2: define limits and sizes for user xattr handling")
Signed-off-by: Jorge Mora <mora@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 251a658bbf ]
A call to listxattr() with a buffer size = 0 returns the actual
size of the buffer needed for a subsequent call. When size > 0,
nfs4_listxattr() does not return an error because either
generic_listxattr() or nfs4_listxattr_nfs4_label() consumes
exactly all the bytes then size is 0 when calling
nfs4_listxattr_nfs4_user() which then triggers the following
kernel BUG:
[ 99.403778] kernel BUG at mm/usercopy.c:102!
[ 99.404063] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
[ 99.408463] CPU: 0 PID: 3310 Comm: python3 Not tainted 6.6.0-61.fc40.aarch64 #1
[ 99.415827] Call trace:
[ 99.415985] usercopy_abort+0x70/0xa0
[ 99.416227] __check_heap_object+0x134/0x158
[ 99.416505] check_heap_object+0x150/0x188
[ 99.416696] __check_object_size.part.0+0x78/0x168
[ 99.416886] __check_object_size+0x28/0x40
[ 99.417078] listxattr+0x8c/0x120
[ 99.417252] path_listxattr+0x78/0xe0
[ 99.417476] __arm64_sys_listxattr+0x28/0x40
[ 99.417723] invoke_syscall+0x78/0x100
[ 99.417929] el0_svc_common.constprop.0+0x48/0xf0
[ 99.418186] do_el0_svc+0x24/0x38
[ 99.418376] el0_svc+0x3c/0x110
[ 99.418554] el0t_64_sync_handler+0x120/0x130
[ 99.418788] el0t_64_sync+0x194/0x198
[ 99.418994] Code: aa0003e3 d000a3e0 91310000 97f49bdb (d4210000)
Issue is reproduced when generic_listxattr() returns 'system.nfs4_acl',
thus calling lisxattr() with size = 16 will trigger the bug.
Add check on nfs4_listxattr() to return ERANGE error when it is
called with size > 0 and the return value is greater than size.
Fixes: 012a211abd ("NFSv4.2: hook in the user extended attribute handlers")
Signed-off-by: Jorge Mora <mora@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6f4de70f7 ]
The intent is to check if the strings' are truncated or not. So, >= should
be used instead of >, because strlcat() and snprintf() return the length of
the output, excluding the trailing NULL.
Fixes: a02d692611 ("SUNRPC: Provide functions for managing universal addresses")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69600231f ]
Some callback functions used here take a boolean argument, others take a
status argument. This breaks KCFI type checking, so clang now warns about
the function pointer cast:
drivers/scsi/bfa/bfad_bsg.c:2138:29: error: cast from 'void (*)(void *, enum bfa_status)' to 'bfa_cb_cbfn_t' (aka 'void (*)(void *, enum bfa_boolean)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Assuming the code is actually correct here and the callers always match the
argument types of the callee, rework this to replace the explicit cast with
a union of the two pointer types. This does not change the behavior of the
code, so if something is actually broken here, a larger rework may be
necessary.
Fixes: 37ea0558b8 ("[SCSI] bfa: Added support to collect and reset fcport stats")
Fixes: 3ec4f2c8bf ("[SCSI] bfa: Added support to configure QOS and collect stats.")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240222124433.2046570-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a7b7f575a ]
strnlen() may return 0 (e.g. for "\0\n" string), it's better to
check the result of strnlen() before using 'len - 1' expression
for the 'buf' array index.
Detected using the static analysis tool - Svace.
Fixes: dc3b66a0ce ("RDMA/rtrs-clt: Add a minimum latency multipath policy")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Link: https://lore.kernel.org/r/20240221113204.147478-1-aleksei.kodanev@bell-sw.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a8bccd8b2 ]
The mad_client will be initialized in enable_device_and_get(), while the
devices_rwsem will be downgraded to a read semaphore. There is a window
that leads to the failed initialization for cm_client, since it can not
get matched mad port from ib_mad_port_list, and the matched mad port will
be added to the list after that.
mad_client | cm_client
------------------|--------------------------------------------------------
ib_register_device|
enable_device_and_get
down_write(&devices_rwsem)
xa_set_mark(&devices, DEVICE_REGISTERED)
downgrade_write(&devices_rwsem)
|
|ib_cm_init
|ib_register_client(&cm_client)
|down_read(&devices_rwsem)
|xa_for_each_marked (&devices, DEVICE_REGISTERED)
|add_client_context
|cm_add_one
|ib_register_mad_agent
|ib_get_mad_port
|__ib_get_mad_port
|list_for_each_entry(entry, &ib_mad_port_list, port_list)
|return NULL
|up_read(&devices_rwsem)
|
add_client_context|
ib_mad_init_device|
ib_mad_port_open |
list_add_tail(&port_priv->port_list, &ib_mad_port_list)
up_read(&devices_rwsem)
|
Fix it by using down_write(&devices_rwsem) in ib_register_client().
Fixes: d0899892ed ("RDMA/device: Provide APIs from the core code to help unregistration")
Link: https://lore.kernel.org/r/20240203035313.98991-1-lishifeng@sangfor.com.cn
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f3dbcb563 ]
csiostor uses function pointer casts to keep the csio_ln_ev state machine
hidden, but this causes warnings about control flow integrity (KCFI)
violations in clang-16 and higher:
drivers/scsi/csiostor/csio_lnode.c:1098:33: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1098 | return (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1369:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1369 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_uninit)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1373:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1373 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_ready)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_lnode.c:1377:29: error: cast from 'void (*)(struct csio_lnode *, enum csio_ln_ev)' to 'csio_sm_state_t' (aka 'void (*)(void *, unsigned int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1377 | if (csio_get_state(ln) == ((csio_sm_state_t)csio_lns_offline)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Move the enum into a shared header so the correct types can be used without
the need for casts.
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213100518.457623-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8fbaa533 ]
Compressed cluster may not be released due to we can fail in
release_compress_blocks(), fix to handle reserved compressed
cluster correctly in reserve_compress_blocks().
Fixes: 4c8ff7095b ("f2fs: support data compression")
Signed-off-by: Sheng Yong <shengyong@oppo.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd244524c2 ]
When we overwrite compressed cluster w/ normal cluster, we should
not unlock cp_rwsem during f2fs_write_raw_pages(), otherwise data
will be corrupted if partial blocks were persisted before CP & SPOR,
due to cluster metadata wasn't updated atomically.
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eae077e6e ]
This patch tries to use bitfield in struct f2fs_io_info to improve
memory usage.
struct f2fs_io_info {
...
unsigned int need_lock:8; /* indicate we need to lock cp_rwsem */
unsigned int version:8; /* version of the node */
unsigned int submitted:1; /* indicate IO submission */
unsigned int in_list:1; /* indicate fio is in io_list */
unsigned int is_por:1; /* indicate IO is from recovery or not */
unsigned int retry:1; /* need to reallocate block address */
unsigned int encrypted:1; /* indicate file is encrypted */
unsigned int post_read:1; /* require post read */
...
};
After this patch, size of struct f2fs_io_info reduces from 136 to 120.
[Nathan: fix a compile warning (single-bit-bitfield-constant-conversion)]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: fd244524c2 ("f2fs: compress: fix to cover normal cluster write with cp_rwsem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d5b9d8156 ]
After commit e3b49ea368 ("f2fs: invalidate META_MAPPING before
IPU/DIO write"), invalidate_mapping_pages() will be called to
avoid race condition in between IPU/DIO and readahead for GC.
However, readahead flow is only used for post_read required inode,
so this patch adds check condition to avoids unnecessary page cache
invalidating for non-post_read inode.
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: fd244524c2 ("f2fs: compress: fix to cover normal cluster write with cp_rwsem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ca06872e ]
Quoted from commit e3b49ea368 ("f2fs: invalidate META_MAPPING before
IPU/DIO write")
"
Encrypted pages during GC are read and cached in META_MAPPING.
However, due to cached pages in META_MAPPING, there is an issue where
newly written pages are lost by IPU or DIO writes.
Thread A - f2fs_gc() Thread B
/* phase 3 */
down_write(i_gc_rwsem)
ra_data_block() ---- (a)
up_write(i_gc_rwsem)
f2fs_direct_IO() :
- down_read(i_gc_rwsem)
- __blockdev_direct_io()
- get_data_block_dio_write()
- f2fs_dio_submit_bio() ---- (b)
- up_read(i_gc_rwsem)
/* phase 4 */
down_write(i_gc_rwsem)
move_data_block() ---- (c)
up_write(i_gc_rwsem)
(a) In phase 3 of f2fs_gc(), up-to-date page is read from storage and
cached in META_MAPPING.
(b) In thread B, writing new data by IPU or DIO write on same blkaddr as
read in (a). cached page in META_MAPPING become out-dated.
(c) In phase 4 of f2fs_gc(), out-dated page in META_MAPPING is copied to
new blkaddr. In conclusion, the newly written data in (b) is lost.
To address this issue, invalidating pages in META_MAPPING before IPU or
DIO write.
"
In previous commit, we missed to cover extent cache hit case, and passed
wrong value for parameter @end of invalidate_mapping_pages(), fix both
issues.
Fixes: 6aa58d8ad2 ("f2fs: readahead encrypted block during GC")
Fixes: e3b49ea368 ("f2fs: invalidate META_MAPPING before IPU/DIO write")
Cc: Hyeong-Jun Kim <hj514.kim@samsung.com>
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: fd244524c2 ("f2fs: compress: fix to cover normal cluster write with cp_rwsem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3b49ea368 ]
Encrypted pages during GC are read and cached in META_MAPPING.
However, due to cached pages in META_MAPPING, there is an issue where
newly written pages are lost by IPU or DIO writes.
Thread A - f2fs_gc() Thread B
/* phase 3 */
down_write(i_gc_rwsem)
ra_data_block() ---- (a)
up_write(i_gc_rwsem)
f2fs_direct_IO() :
- down_read(i_gc_rwsem)
- __blockdev_direct_io()
- get_data_block_dio_write()
- f2fs_dio_submit_bio() ---- (b)
- up_read(i_gc_rwsem)
/* phase 4 */
down_write(i_gc_rwsem)
move_data_block() ---- (c)
up_write(i_gc_rwsem)
(a) In phase 3 of f2fs_gc(), up-to-date page is read from storage and
cached in META_MAPPING.
(b) In thread B, writing new data by IPU or DIO write on same blkaddr as
read in (a). cached page in META_MAPPING become out-dated.
(c) In phase 4 of f2fs_gc(), out-dated page in META_MAPPING is copied to
new blkaddr. In conclusion, the newly written data in (b) is lost.
To address this issue, invalidating pages in META_MAPPING before IPU or
DIO write.
Fixes: 6aa58d8ad2 ("f2fs: readahead encrypted block during GC")
Signed-off-by: Hyeong-Jun Kim <hj514.kim@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: fd244524c2 ("f2fs: compress: fix to cover normal cluster write with cp_rwsem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71f2c82062 ]
Commit 3c62be17d4 ("f2fs: support multiple devices") missed
to support direct IO for multiple device feature, this patch
adds to support the missing part of multidevice feature.
In addition, for multiple device image, we should be aware of
any issued direct write IO rather than just buffered write IO,
so that fsync and syncfs can issue a preflush command to the
device where direct write IO goes, to persist user data for
posix compliant.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: fd244524c2 ("f2fs: compress: fix to cover normal cluster write with cp_rwsem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21a8870c9 ]
Upon rare occasions, KASAN reports a use-after-free Write
in srpt_refresh_port().
This seems to be because an event handler is registered before the
srpt device is fully setup and a race condition upon error may leave a
partially setup event handler in place.
Instead, only register the event handler after srpt device initialization
is complete.
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Link: https://lore.kernel.org/r/20240202091549.991784-2-william.kucharski@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a39d51ff1f ]
If a usb audio device sets more bits than the amount of channels
it could write outside of the map array.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Fixes: 04324ccc75 ("ALSA: usb-audio: add channel map support")
Message-ID: <20240313081509.9801-1-johan.carlsson@teenage.engineering>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c062166995 ]
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
- https://bugzilla.kernel.org/show_bug.cgi?id=189331
- https://bugzilla.kernel.org/show_bug.cgi?id=216632
- https://bugzilla.kernel.org/show_bug.cgi?id=216311
- https://bugzilla.kernel.org/show_bug.cgi?id=213507
Signed-off-by: Athaariq Ardhiansyah <foss@athaariq.my.id>
Message-ID: <20240310140249.3695-1-foss@athaariq.my.id>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7938e9ce39 ]
The kmalloc() in zynq_clk_setup() will return null if the
physical memory has run out. As a result, if we use snprintf()
to write data to the null address, the null pointer dereference
bug will happen.
This patch uses a stack variable to replace the kmalloc().
Fixes: 0ee52b157b ("clk: zynq: Add clock controller driver")
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20240301084437.16084-1-duoming@zju.edu.cn
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97fe4901e ]
It is possible for clk_core_get to dereference a NULL in the following
sequence:
clk_core_get()
of_clk_get_hw_from_clkspec()
__of_clk_get_hw_from_provider()
__clk_get_hw()
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL.
Fixes: dde4eff47c ("clk: Look for parents with clkdev based clk_lookups")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240302-linux-next-24-03-01-simple-clock-fixes-v1-1-25f348a5982b@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
