Instead of using a mix of -EOPNOTSUPP and -ENOTSUPP, use the more
standard -EINVAL to signal that the specified polarity value was
invalid.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
A single blank line is enough to separate logical code blocks.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Using gotos for conditional code complicates this code significantly.
Convert the code to simple conditional blocks to increase readability.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Intel Lightning Mountain(LGM) SoC contains a PWM fan controller. This
PWM controller does not have any other consumer, it is a dedicated PWM
controller for fan attached to the system. Add driver for this PWM fan
controller.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Introduce driver for Synopsys DesignWare PWM Controller used on Intel
Elkhart Lake.
Initial implementation is done by Felipe Balbi while he was working at
Intel with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The MediaTek PWM IP can sometimes use the 26 MHz source clock to
generate the PWM signal, but the driver currently assumes that we always
use the PWM bus clock to generate the PWM signal.
This commit modifies the PWM driver in order to force the PWM IP to
always use the bus clock as source clock.
I do not have the datasheet of all the MediaTek SoC, so I don't know if
the register to choose the source clock is present in all the SoCs or
only in subset. As a consequence I made this change optional by using a
platform data paremeter to says whether this register is supported or
not. On all the SoCs I don't have the datasheet (MT2712, MT7622, MT7623,
MT7628, MT7629) I kept the behavior to be the same as before this
change.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When there are other PWM controllers enabled along with pwm-lp3943,
pwm-lp3942 is failing to probe with -EEXIST error. This is because
other PWM controllers are probed first and assigned PWM base 0 and
pwm-lp3943 is requesting for 0 again.
In order to avoid this, assign the chip base with -1, so that it is
dynamically allocated.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add sama5d2 support. The sama5d2 has a new clock input, its gclk. Index 0
of the clock selector is the gclk instead of the peripheral clock divided
by 2.
For now, the gclk is not used because the peripheral clock divided by 8
already gives a 9.6ns resolution which is enough for most use cases.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM is now a subnode of the used TCB. This is cleaner and it mainly
allows to stop wasting TCB channels when only 2 or 4 PWMs are used.
This also removes the atmel_tclib dependency
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The devm_clk_get() may return -EPROBE_DEFER which is not handled properly
by TI EHRPWM driver and causes unnecessary boot log messages.
Hence, add proper deferred probe handling with new dev_err_probe() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As the comment above the code setting the DPM_FLAG_NO_DIRECT_COMPLETE
flag explains:
/*
* On Cherry Trail devices the GFX0._PS0 AML checks if the controller
* is on and if it is not on it turns it on and restores what it
* believes is the correct state to the PWM controller.
* Because of this we must disallow direct-complete, which keeps the
* controller (runtime)suspended, on resume to avoid 2 issues:
* 1. The controller getting turned on without the linux-pm code
* knowing about this. On devices where the controller is unused
* this causes it to stay on during the next suspend causing high
* battery drain (because S0i3 is not reached)
* 2. The state restoring code unexpectedly messing with the controller
*/
The pm-core must not skip resume to avoid the GFX0._PS0 AML code messing
with the PWM controller behind our back. But leaving the controller
runtime-suspended (skipping runtime-resume + normal-suspend) during
suspend is fine. Set the DPM_FLAG_SMART_SUSPEND flag to allow this.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
ACPI LPSS devices use direct-complete style suspend/resume handling by
default. We set the DPM_FLAG_SMART_PREPARE and define a prepare handler
to disable this on Cherry Trail devices.
Clean this up a bit by setting the DPM_FLAG_NO_DIRECT_COMPLETE flag for
Cherry Trail devices, instead of defining a prepare handler.
While at it also improve the comment explaining why this is necessary.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_lpss_is_updating() does a sanity check which should never fail.
If the check does actually fail that is worth logging an error,
especially since this means that we will skip making the requested
changes to the PWM settings.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ab8500 driver is the last one which doesn't (explicitly) use dynamic
allocation of the pwm id. Looking through the kernel sources I didn't
find a place that relies on this id. And with the device probed from
device tree pdev->id is -1 anyhow; making this explicit looks
beneficial, too.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwmchip_add() doesn't emit an error message, so add one in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use devm_platform_ioremap_resource() to simplify code. While at it, also
declare the "i" and "ret" variables on the same line since they are of
the same type.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
