Use skin temperature for maintaining temperature that is suitable
specifically for Nexus 7. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use skin temperature for maintaining temperature that is suitable
specifically for A500. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The verbose variant of the atmel,wakeup-method value was lost when patch
that added the property was merged because it conflicted with other patch,
re-add it for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor and enable it in pinmux,
for completeness.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU
temperature reporting and thermal throttling is available on all Tegra30
devices universally.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Like always, the DT branch is sizable. There are numerous additions and
fixes to existing platforms, but also a handful of new ones introduced.
Less than some other releases, but there's been significant work on
cleanups, refactorings and device enabling on existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and 5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs, and
new support for Microsoft Surface Duo (SM8150-based), Huawei Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and NanoPi
R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added
-----BEGIN PGP SIGNATURE-----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=X6PF
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Olof Johansson:
"Like always, the DT branch is sizable. There are numerous additions
and fixes to existing platforms, but also a handful of new ones
introduced. Less than some other releases, but there's been
significant work on cleanups, refactorings and device enabling on
existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the
Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for
rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and
5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc
definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs,
and new support for Microsoft Surface Duo (SM8150-based), Huawei
Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and
NanoPi R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added"
* tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (511 commits)
arm64: dts: rockchip: add basic dts for RK3568 EVB
arm64: dts: rockchip: add core dtsi for RK3568 SoC
arm64: dts: rockchip: add generic pinconfig settings used by most Rockchip socs
ARM: dts: rockchip: add vpu and vdec node for RK322x
ARM: dts: rockchip: add vpu nodes for RK3066 and RK3188
ARM: dts: rockchip: add vpu node for RK3036
arm64: dts: ipq8074: Add QUP6 I2C node
arm64: dts: rockchip: Re-add regulator-always-on for vcc_sdio for rk3399-roc-pc
arm64: dts: rockchip: Re-add regulator-boot-on, regulator-always-on for vdd_gpu on rk3399-roc-pc
arm64: dts: rockchip: add ir-receiver for rk3399-roc-pc
arm64: dts: rockchip: Add USB-C port details for rk3399 Firefly
arm64: dts: rockchip: Sort rk3399 firefly pinmux entries
arm64: dts: rockchip: add infrared receiver node to RK3399 Firefly
arm64: dts: rockchip: add SPDIF node for rk3399-firefly
arm64: dts: rockchip: Add Rotation Property for OGA Panel
arm64: dts: qcom: sc7180: bus votes for eMMC and SD card
arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen
arm64: dts: qcom: sm8250-edo: Enable GPI DMA
arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI
arm64: dts: qcom: sm8250-edo: Enable PCIe
...
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
- Make it clear __swp_entry_to_pte() uses PTE_TYPE_FAULT
- Updates for setting vmalloc size via command line to resolve an issue
with the 8MiB hole not properly being accounted for, and clean up the
code.
- ftrace support for module PLTs
- Spelling fixes
- kbuild updates for removing generated files and pattern rules for
generating files
- Clang/llvm updates
- Change the way the kernel is mapped, placing it in vmalloc space
instead.
- Remove arm_pm_restart from arm and aarch64.
-----BEGIN PGP SIGNATURE-----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=dq60
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM development updates from Russell King:
- Make it clear __swp_entry_to_pte() uses PTE_TYPE_FAULT
- Updates for setting vmalloc size via command line to resolve an issue
with the 8MiB hole not properly being accounted for, and clean up the
code.
- ftrace support for module PLTs
- Spelling fixes
- kbuild updates for removing generated files and pattern rules for
generating files
- Clang/llvm updates
- Change the way the kernel is mapped, placing it in vmalloc space
instead.
- Remove arm_pm_restart from arm and aarch64.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (29 commits)
ARM: 9098/1: ftrace: MODULE_PLT: Fix build problem without DYNAMIC_FTRACE
ARM: 9097/1: mmu: Declare section start/end correctly
ARM: 9096/1: Remove arm_pm_restart()
ARM: 9095/1: ARM64: Remove arm_pm_restart()
ARM: 9094/1: Register with kernel restart handler
ARM: 9093/1: drivers: firmwapsci: Register with kernel restart handler
ARM: 9092/1: xen: Register with kernel restart handler
ARM: 9091/1: Revert "mm: qsd8x50: Fix incorrect permission faults"
ARM: 9090/1: Map the lowmem and kernel separately
ARM: 9089/1: Define kernel physical section start and end
ARM: 9088/1: Split KERNEL_OFFSET from PAGE_OFFSET
ARM: 9087/1: kprobes: test-thumb: fix for LLVM_IAS=1
ARM: 9086/1: syscalls: use pattern rules to generate syscall headers
ARM: 9085/1: remove unneeded abi parameter to syscallnr.sh
ARM: 9084/1: simplify the build rule of mach-types.h
ARM: 9083/1: uncompress: atags_to_fdt: Spelling s/REturn/Return/
ARM: 9082/1: [v2] mark prepare_page_table as __init
ARM: 9079/1: ftrace: Add MODULE_PLTS support
ARM: 9078/1: Add warn suppress parameter to arm_gen_branch_link()
ARM: 9077/1: PLT: Move struct plt_entries definition to header
...
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
that's just a bunch of data so the diffstat reflects that. Looking beyond that
there's just a bunch of updates all around in various clk drivers. Renesas and
NXP (for i.MX) are two SoC vendors that have a lot of patches in here. Overall
the driver changes look to be mostly enabling more clks and non-critical fixes
that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates clkdev to be
the only implementation of clk_get() and clk_put(). That's a good step in the
right direction to migreate eveerything over to the common clk framework. Now
we don't have to worry about clkdev specific details, they're just part of the
clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is implemented in
only one place in the kernel instead of in drivers/clk/clkdev.c and in
architectures that want their own implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif, audio,
parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate()
and improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework
-----BEGIN PGP SIGNATURE-----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=YnCF
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAmDZzHUACgkQCF8+vY7k
4RWjmQ//QSMEAlz/Xv7YmnkheMEbEvMGgRzUK6UIzfbI9sb2ZPx/1dYySVExrPba
Z1WtrH9oEZGX75IwRSBb6Kb0j2k3E1Y9UZzaAAofE4yyrw5sH8oNvhxhAdak+YRC
XaVJq3xulIq/ClsEyaDzZPFfIhZ5Uo/Cz9s4bZMiA8IwZOImnttJmbrw+Og9ly0+
TrvA0MMkO790h+OOnu5Lv1Q2qJZXaVoTIZ+/icDW29WbQdTQnEZ6XOz/Y+4BZFwW
dA49MLdz7BlypV7a3ijIM4ENPrPmmRIf5agKkQ13Z84gNH14Vb8zShDFq2vHwdKC
7qqvZLuCug/GyK7hyPQHOM8b7wN2utNMZCJIcWVob4oZDzHSvLO+wFI4RCI/RBdY
3tOxrH5cd1FJXB5Vi4KtWNk2Ne63UyaJUYSDk9j30LSwNC/EA6+7fc9LeRY2ykNg
rSD8aXMBoHWtxPxBH5O1ljVdbvG4f8Ds6Yb1cjrxvQWIXvzE7TIC2zhRl0o/r6My
1BWOkVVHw0i5/U+PTyQnVK2XYprq0Jp0b9a0ErkJoOtRpd4VW0pFFcDzWN2tlR0h
McIinHAXdeZO6qHbNMyArYcwfTgWP51IWKm5qDQxPtEnrZDQIjbG3GfZZz9wtks/
Moz7vUTbSUaxSqY/Eg+meg1lilU/lyee9O6hhKCDsVQDxaZUKU8=
=VQX8
-----END PGP SIGNATURE-----
Merge tag 'media/v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- V4L2 core control API was split into separate files
- New RC maps: tango and tc-90405
- Hantro driver got support for G2/HEVC decoder
- av7710 is moving to staging, together with some legacy APIs
- several cleanups related to compat_ioctl32 code
- Move the MPEG-2 stateless control type out of staging
- Address several issues with RPM get logic on media drivers
- Lots of cleanups, bug fixes and improvements.
* tag 'media/v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (394 commits)
media: s5p-mfc: Fix display delay control creation
media: mtk-vpu: on suspend, read/write regs only if vpu is running
media: video-mux: Skip dangling endpoints
media: Fix Media Controller API config checks
media: i2c: rdacm20: Re-work ov10635 reset
media: i2c: rdacm20: Check return values
media: i2c: rdacm20: Report camera module name
media: i2c: rdacm20: Enable noise immunity
media: i2c: rdacm20: Embed 'serializer' field
media: i2c: rdacm21: Power up OV10640 before OV490
media: i2c: rdacm21: Fix OV10640 powerup
media: i2c: rdacm21: Add delay after OV490 reset
media: i2c: max9271: Introduce wake_up() function
media: i2c: max9271: Check max9271_write() return
media: i2c: max9286: Rework comments in .bound()
media: i2c: max9286: Define high channel amplitude
media: i2c: max9286: Cache channel amplitude
media: i2c: max9286: Rename reverse_channel_mv
media: i2c: max9286: Adjust parameters indent
media: hantro: add support for Rockchip RK3036
...
Minor devicetree clean-up for omaps for the binding checks:
- Drop unsupported dmas for omap2/3 i2c
- Drop redundant ehrpwm compatible
- Drop am33xx-ecap compatible no longer needed
- Correct node names for ecap
- Drop unsupported interrupts for ecap
- Drop redundant ti,pcf8575
- Correct usage for ti,pindir-d0-out-d1-in
-----BEGIN PGP SIGNATURE-----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=+JIZ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAmDT4+0PHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3TrsP/0eWFe2pXp5QkcFSdnyGMjoKDTB6qikVleTT
CnQK3uX/bZnEH5lEbZFXaovnI4MZjQ5hqJm7YIrQ9sRVVGfpAOqm53xVP+F9Oh2o
8b84HSNV0bYC0Uy56WLlSJPF2AIxrvGr+DNI4+F3R66xTjHMZ+yzW+iHOdzA4HMi
adLkAeob1aVAKmijDq0zM1/hAAp4/vavhudCQbFTxRYnLCppikDE7SOasE1fz6mV
6c2iqnPGCRx6krkYwqfwA+92Ur/6MaIuo1TbRkPn6QWcVqRmIoV5+MqfC/dNDFcC
JRnksSVCrmnAz2+PDJKtN/1Ejo1V/wn992/bmefPoqsJibeVZ/jYh+K4zWTpsSrK
pOKI9FRgStbJwiPHAPndTnBhX0CM9V9BA5oz0M/geU59SxlqNqTZIn+6lqcbue2e
WNL0vqZ+UCVkUowofD17orUhhaq6C+oey3mFhUNxN4wHTNDsLhYr6gn59JL4INlG
yojlOq2X+awYu46Ws7CZ+du08R3C+OUnBgNk/ewBISy17Tdr7YgE/p98svs7XCKi
br50JPsSvdOkC31wunyrklTbux0gbyx2STfx+fqqf7UBs5kgt5uTypamIwLn0r/9
j4DozfW8TBVnd89p9oZzaB9yYvpEXWWQWKzxm+CgvBM9lBp4BwTjs9atlKnl6YF2
VLapKhzB
=ZjIL
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.14/dt-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree binding clean-up for omaps for v5.14
Minor devicetree clean-up for omaps for the binding checks:
- Drop unsupported dmas for omap2/3 i2c
- Drop redundant ehrpwm compatible
- Drop am33xx-ecap compatible no longer needed
- Correct node names for ecap
- Drop unsupported interrupts for ecap
- Drop redundant ti,pcf8575
- Correct usage for ti,pindir-d0-out-d1-in
* tag 'omap-for-v5.14/dt-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x: align ti,pindir-d0-out-d1-in property with dt-shema
ARM: dts: am335x: align ti,pindir-d0-out-d1-in property with dt-shema
ARM: dts: dra7x-evm: Drop "ti,pcf8575"
ARM: dts: am33xx: Drop interrupt property from ecap nodes
ARM: dts: ti: Fix node name for all ecap dt nodes
ARM: dts: ti: Drop usage of ti,am33xx-ecap from DT nodes
ARM: dts: ti: drop usage of redundant compatible
ARM: dts: omap2/3: Drop dmas property from I2C node
Link: https://lore.kernel.org/r/pull-1624002812-396117@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
USB4 is only present in DRA74x variants, and I managed to add it for the
other variants too with the recent legacy platform data removal.
-----BEGIN PGP SIGNATURE-----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=pfkv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zTsh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.13/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix duplicate usb4 regression for dra74 variants
USB4 is only present in DRA74x variants, and I managed to add it for the
other variants too with the recent legacy platform data removal.
* tag 'omap-for-v5.13/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Fix duplicate USB4 target module node
Link: https://lore.kernel.org/r/pull-1623999845-180025@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The VPU and the VDEC IP block of RK322x are the same as RK3399 has and
the drivers can be used as-is.
Add the respective nodes to the device tree.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210527154455.358869-13-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the vpu node to the common rk3xxx.dtsi and only the powerdomain
property to the SoC specific device trees.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210527154455.358869-12-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
s/Hisilicon/HiSilicon/.
It should use capital S, according to the official website
https://www.hisilicon.com/en.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
- Set the fifo-size of uart_A to 128 bytes like the ARM64 counterpart
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmDHDeIACgkQd9zb2sjI
SdGIIRAAvh9vMH7rNZU6NbClOicifzw9vDWbCz2ArreTr6DepIZR1DdCUdcT46X8
mH6/TyN5ZC1t1QPl0bDWzGZIUS9mAkNQRsmY4eXJgXttokzNe7RxE0PSqk5bJeP7
tzZypnk7nSjIj5w9Y/BxhTI6j3BB6OZcD5lI6AvjBN3eBZkTY6yXPnlASwiRUnpj
a46MOVoEI7jpVAAOAq/ATaelFHKYXu/Gg4lp/EhipOk+SRZPmRqRteTRLHmUjRLl
xOBAsee177qz09dVvcdiTOLqSF8MBwYE4H0g7AhpHlQZZz3SUr0B9Wg090n0wS56
FgA/U21W1Yl2B4bSyrAvjzFMhvkEfRmc63gzx3xuOq8s/PW83mGKNQ9UUvqaKWtf
yEbKiaS9l6Dqm//U96ndSf6pGmdOaCVoctOXqASEikxBY12JD/51LnbRyup4qmWK
M4rkRgbT6djyrFhuAEUDVA3ddZBy7lVZBC4SV2OMlOLwZPDiKh/aQwlSX00NnWiW
fAYra0TsI8hnPLO+PwNnNxIIxaEiEizQ2tpGiZdxfC52u9KzfgCst40yDzqLhDPt
MrkHSVQcUvPLZsF0sHIizljozSwGqM1dRyDO41sUtwK0ej+dsuLM+LaheapTxgUe
f8oaaTF6zOOwklaEX/m5mPRjJ/GDZ1mHAuII2St/8/LksXTEkNQ=
=r+Ju
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yNYd
-----END PGP SIGNATURE-----
Merge tag 'amlogic-arm-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM DT changes for v5.14:
- Set the fifo-size of uart_A to 128 bytes like the ARM64 counterpart
* tag 'amlogic-arm-dt-for-v5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson: Set the fifo-size of uart_A to 128 bytes
Link: https://lore.kernel.org/r/2f19a5a1-3ed9-dd11-02f1-7d535cb1c25c@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the definition of both an oscillator at 12Mhz required by the
the watchdog and the watchdog device node.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
This contains various improvements (such as microphone detection and
thermal zones) for some older Tegra devices (such as the Nexus 7 or
the Acer A500).
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmDDjcsTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zodS9D/9DcmPSJlwv21gK3e9HzLxDZDkTaX2Q
UEvqrgIaCsUG9Nby6dzE8A8iqNT1rwev4kh/6qYE1pRQV2NY4/apyUrjGrPAicHH
7vi69ROyOk2PFVEWvhwEpjjioYZIlGsaz4R6Uc3PtwA3lrnUtAtU/98mN/XFRkre
/hs/tohVROqPMGBV2x49BwNC6E3grnFsd/sSgt8SIIaCQmMz84lhsf/iGRXO4BbU
T1FPoLXXpNuAU8rv8vxupir2omgJoEDRp1bQHCEGrLHNS8hz1lNkKJbfYwwJw1rt
DxM781HxlU0a4nYaZtPWy/dRpdPQjm8Vrpwc3psQXBEZqrQVCpkF/bZG+dqIeE6q
zINAcp1JFbKTVdbCr5Q26tITUGxARnk9Xfyz68ieuJXvM2xpEhNECcl77+uELAOy
BHkUD0Ry373RYSk1PD0KIM1HQqmBB4CNh67Gx7NMRZPYd1fdI6O6TAGZeOzLh5OT
UVDjqwB+5NMxF8TMwcWAH58XQR94dWbF6h3/f4WQrMB0yizMUCsbxjciQOhm1V9b
j9qbExP5OIrETzxEYXM+c0tEbwLjMPXmk2I952Bls5rixzb6mY3ueGMEyndhu6Yu
0zQibcmCulggjmzDAQzyxLRLdndDqvDTR4q9ka5xOSbbxRJCh2S5BtlfakeCbTvj
gh8X+rfLrVqD9w==
=JLFw
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.14-rc1
This contains various improvements (such as microphone detection and
thermal zones) for some older Tegra devices (such as the Nexus 7 or
the Acer A500).
* tag 'tegra-for-5.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: ouya: Enable memory frequency thermal throttling using ACTMON
ARM: tegra: nexus7: Enable memory frequency thermal throttling using ACTMON
ARM: tegra: Add cooling cells to ACTMON device-tree node
ARM: tegra: nexus7: Correct 3v3 regulator GPIO of PM269 variant
ARM: tegra: nexus7: Remove monitored-battery property
ARM: tegra: nexus7: Improve thermal zones
ARM: tegra: nexus7: Add i2c-thermtrip node
ARM: tegra: paz00: Add CPU thermal zone
ARM: tegra: wm8903: Fix polarity of headphones-detection GPIO in device-trees
ARM: tegra: Add reg property to Tegra20 EMC table device-tree nodes
ARM: tegra: acer-a500: Bump thermal trips by 10C
ARM: tegra: acer-a500: Specify proper voltage for WiFi SDIO bus
ARM: tegra: acer-a500: Improve microphone detection
Link: https://lore.kernel.org/r/20210611164437.3568059-4-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds DMA, NAND controllers, USB controller and PHY, RPM, L2CC,
thermal sensors and defines thermal zones. It them enables these for the
RB3011.
-----BEGIN PGP SIGNATURE-----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=n/jg
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm DTS updates for v5.14
This adds DMA, NAND controllers, USB controller and PHY, RPM, L2CC,
thermal sensors and defines thermal zones. It them enables these for the
RB3011.
* tag 'qcom-dts-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: Enable NAND + USB for RB3011
ARM: dts: qcom: add L2CC and RPM for IPQ8064
ARM: dts: qcom: Add USB port definitions to ipq806x
ARM: dts: qcom: Add tsens details to ipq806x
ARM: dts: qcom: Add ADM DMA + NAND definitions to ipq806x
Link: https://lore.kernel.org/r/20210614223840.393224-1-bjorn.andersson@linaro.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Failure to properly define "secure-regions" as 64-bit ranges prevents
the two SDX55 boards from booting, so correct this.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAmDH0BobHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3F8wMP/3kOqs8FerhjMYnK1vxq
kPd8O7C/xrrm+hKfbjLLXvNPqYkj+JNEJ2uOcTM0KhCgnk1iupSrUHJmMQ0IqGgr
5qbPMRT1aL059VipLrY9wFPiqpPijO4D8K6/6h60NDYSPpTxaLkvePgrapdsdjlt
wboP4vS627gAC8rvxV6pgOXSqNGxsw1b4F83ytKuNYxZenYZlT0JrGLvFQnezeQE
x96sGMbTnOy7eiGML2zzdjhoWot1b9EcmMlYcrbgwSMLkF2SktMe72KYSmvOQC/y
QhvlmC4+WlGqJW8wKewxmOnzYyZYA5hLxYpMld2sRJQfk0+KmQuC2AYpp4y+DK54
gHYUTsNAMQw20iRDG0+gLuQ8SkviYkTtuIlJNACU0Q46vrc868D4wXbHQ7gtAnO1
RRKMqVOD9AVPeMo4wPK6KD06chuTByJC6dhXPM4ThTLTEUpaZ1cC0DoJcN14+Lx+
mE4GLEl1lMMOWMFmSPDE52cX2di2VuAHvE81/BNHotwzVg2mR4nIBwEBjLp4W7im
3BgRa/m4+ekh21hQ+OXzjXEeeWhRdyQmH/wnx2GvDH/7B1YB1JI1NWczlqwVNqGJ
uQqD/pHLKQogFCbOaXLUgan396Kn4pS3ViEolekwJ4WzebsbpcRsp/tz4x071H1O
A1TSPvlnpB0FAYzQqYIBfEJM
=572G
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-fixes-for-5.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm DTS fixes for v5.13
Failure to properly define "secure-regions" as 64-bit ranges prevents
the two SDX55 boards from booting, so correct this.
* tag 'qcom-dts-fixes-for-5.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: sdx55-telit: Represent secure-regions as 64-bit elements
ARM: dts: qcom: sdx55-t55: Represent secure-regions as 64-bit elements
Link: https://lore.kernel.org/r/20210614215552.391887-1-bjorn.andersson@linaro.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The Ux500 HREF LEDs have not been probing properly for a
while as this was introduce:
ret = of_property_read_u32(np, "color", &led_color);
if (ret)
return ret;
Since the device tree did not define the new invented color
attribute, probe was failing.
Define color attributes for the LEDs so they work again.
Link: https://lore.kernel.org/r/20210613123356.880933-1-linus.walleij@linaro.org
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: stable@vger.kernel.org
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: i.MX6Q DaSheng COM-9XX SBC board, i.MX28 based XEA
board, GE B1x5v2 boards.
- A series from Christoph Niedermaier to correct imx6q-dhcom
descriptions, add device aliases and ethernet VIO regulator.
- Correct Ethernet node name for imx51-digi-connectcore-som and
imx53-ard board to comply DT schema.
- A couple of update on imx6dl-yapp4 board, configuring OLED display
segment offset, and using aliases to set custom MMC device indexes.
- A series from Oleksij Rempel and Robin van der Gracht to update
Protonic boards: imx6dl-prtvt7, imx6dl-plym2m and imx6qdl-vicut1.
- A series from Shengjiu Wang to improve various audio support on NXP
reference boards.
- Rename pinfunc for i.MX25 GPIO_[A-F] pads for consistency.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmDFuRMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4VgAf/Z69ssu3l3ZPrHncXx6bnX7X+Ja0H
NxccV3DBtdaaCBODM9bnJ3HbWA3PFX0azA2q2CdOpjyk7UWeRO/RuZ5GZbdWkZfK
VrlJxX9fPpvJZp6HQS0a4cVHgJZDJ5hSef+ThwE/Yanm0cf+0vOW5M3enR+1j/xD
tsIyno5dj3I0dailhZy5KCChYznWF1DJcJ7spm5AAejXV+iSAX1q29zQ4q6yT/18
9zfuinaz3zrg0eN7qNpU5XziNv0Dbr06VBWM5Tfiio4DL7iM5jePA1LjWrvmH2Sk
NC1Kjke3ahl7illudSHUhtmLwtYh7dpRElf6saZBPMP+OpKF+hiAEog/2w==
=ja0d
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.14:
- New board support: i.MX6Q DaSheng COM-9XX SBC board, i.MX28 based XEA
board, GE B1x5v2 boards.
- A series from Christoph Niedermaier to correct imx6q-dhcom
descriptions, add device aliases and ethernet VIO regulator.
- Correct Ethernet node name for imx51-digi-connectcore-som and
imx53-ard board to comply DT schema.
- A couple of update on imx6dl-yapp4 board, configuring OLED display
segment offset, and using aliases to set custom MMC device indexes.
- A series from Oleksij Rempel and Robin van der Gracht to update
Protonic boards: imx6dl-prtvt7, imx6dl-plym2m and imx6qdl-vicut1.
- A series from Shengjiu Wang to improve various audio support on NXP
reference boards.
- Rename pinfunc for i.MX25 GPIO_[A-F] pads for consistency.
* tag 'imx-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
ARM: dts: imx6: Add GE B1x5v2
ARM: dts: imx6q-dhcom: Add ethernet VIO regulator
ARM: dts: imx6q-dhcom: Add aliases for i2c, serial and rtc
ARM: dts: imx6q-dhcom: Add gpios pinctrl for i2c bus recovery
ARM: dts: imx6q-dhcom: Fix ethernet plugin detection problems
ARM: dts: imx6q-dhcom: Fix ethernet reset time properties
ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node
ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97
ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes
ARM: dts: imx6dl-prtvt7: Enable the VPU
ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards
ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
ARM: dts: imx53-ard: Correct Ethernet node name
ARM: dts: i.MX51: digi-connectcore-som: Correct Ethernet node name
ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value
ARM: dts: imx6: edmqmx6: set phy-mode to RGMII-ID
ARM: dts: imx6qdl-sabresd: Configure the gpio for hp detect
...
Link: https://lore.kernel.org/r/20210613082544.16067-4-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The first UART controller in the "Everything-Else" power domain is
called uart_A. Unlike all other UARTs (which use a 64 byte fifo-size in
hardware) uart_A has a fifo-size of 128 bytes. This UART controller is
typically used for Bluetooth HCI.
The fifo-size of 128 bytes is valid from all SoCs from Meson6 (or
possibly even earlier) all the way up to the latest 64-bit ones.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210604170844.2201229-1-martin.blumenstingl@googlemail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the power controller node and the correspondending qos nodes for
RK322x.
Also add the power-domain property to the nodes that are already
present.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210527154455.358869-10-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the power controller node and the correspondending qos nodes for
RK3036.
Also add the power-domain property to the nodes that are already
present.
Note: Since the regiser offsets of the axi interconnect QoS are missing
in the TRM (RK3036 TRM V1.0), they have been taken from vendor kernel.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210527154455.358869-9-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While the kernel doesn't care so much right now, boot loaders like
u-boot need to refine the node on their side, so to make life easier
for everyone add the labels to the timer nodes on rk3066a.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210612184733.2331-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SL3516 SoC has a crypto offloader IP.
This patch adds it on the gemini SoC Device-tree.
Link: https://lore.kernel.org/r/20210611220501.684997-1-linus.walleij@linaro.org
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
mainly:
- I2S Support for the V3
- Audio Codec Support for the V3s
- DMA support for the V3s
- PWM support for the V3s
- Support for Bluetooth Audio on the pinephone
- Add A10-like timers to the A64 and R40
- New boards: Forlinx OKA40i-C, Forlinx OKA40i-C, NanoPi R1S H5
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYMN5hwAKCRDj7w1vZxhR
xa2sAP0Y4UY9ncxWmuTUMgi4osqscowxGUsCHdfxP+Yk9/IJ8wEAqKA5tfior25d
guy+cgXft/CixRtgv6Go3W55tJpZ6wQ=
=A9Cb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to improve the Allwinner SoCs support,
mainly:
- I2S Support for the V3
- Audio Codec Support for the V3s
- DMA support for the V3s
- PWM support for the V3s
- Support for Bluetooth Audio on the pinephone
- Add A10-like timers to the A64 and R40
- New boards: Forlinx OKA40i-C, Forlinx OKA40i-C, NanoPi R1S H5
* tag 'sunxi-dt-for-5.14-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (29 commits)
ARM: dts: sun8i: v3s: enable emac for zero Dock
arm64: dts: allwinner: pinephone: Set audio card name
ARM: dts: sun8i: r40: Add timer node
ARM: dts: sun8i: V3: add I2S interface to V3 dts
dt-bindings: sound: sun4i-i2s: add Allwinner V3 I2S compatible
ARM: dts: sun8i: V3: add codec analog frontend to V3 dts
ASoC: dt-bindings: sun8i-a23-codec-analog: add compatible for Allwinner V3
ARM: dts: sun8i: v3s: add analog codec and frontend to v3s dts
ARM: dts: sun8i: v3s: add DMA properties to peripherals supporting DMA
ARM: dts: sun8i: v3s: add DMA controller to v3s dts
ARM: dts: sun8i: v3s: add pwm controller to v3s dts
dt-bindings: pwm: allwinner: add v3s pwm compatible
arm64: dts: allwinner: h5: Add NanoPi R1S H5 support
dt-bindings: arm: Add NanoPi R1S H5
arm64: dts: allwinner: pinephone: Add support for Bluetooth audio
arm64: dts: allwinner: a64: Allow multiple DAI links
arm64: dts: allwinner: a64: Add pinmux nodes for AIF2/AIF3
arm64: dts: allwinner: a64: Allow using multiple codec DAIs
ARM: dts: sun8i-a33: Allow using multiple codec DAIs
ASoC: dt-bindings: sun8i-codec: Increase #sound-dai-cells
...
Link: https://lore.kernel.org/r/96cc77ec-139d-4685-8a66-a60964cf39fd.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix for sama5d4 gpio mux
- A trivial fix for DT documentation
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYMNX7gAKCRAfOrpwrNPN
DJa1AQCeS3dhkLRYeDZ56/QLM5fEOc8Udqml4JS2iGX16wJ9hQD9FdBKiXbRUvUV
mq2JQ0C1smb6Ro5KPpHqlpJTtIfxNAE=
=HggT
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 dt for 5.14:
- A fix for sama5d4 gpio mux
- A trivial fix for DT documentation
* tag 'at91-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
dt-bindings: i2c: at91: fix example for scl-gpios
ARM: dts: at91: sama5d4: fix pinctrl muxing
Link: https://lore.kernel.org/r/20210611123446.20510-1-nicolas.ferre@microchip.com
Signed-off-by: Olof Johansson <olof@lixom.net>
