The control handler is leaked in some probe-time error paths, as well as
in the remove path. Fix it.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The power-up GMSL link configuration is controlled by the HIM and BWS
pins, whose state is reflected in register 0x1c. Print the detected
power-up config in a debug message to help debugging.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
GMSL can transport three synchronization signals: VSync, HSync and Data
Enable. The MAX9286 can select either HS or DE as a line valid signal.
Not all serializers (and transmission formats) support the DE signal.
The MAX9271, used by the RDACM20 and RDACM21 cameras, doesn't document
DE support. Nonetheless, the max9286 driver selects the DE signal as
line valid in register 0x0c (by not setting the DESEL bit). It's not
clear why this works. As HS is a more common line valid qualifier, set
the DESEL bit by default. This is needed to support the onsemi MARS
cameras.
If a camera requires usage of the DE signal in the future, this will
need to be made configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org> # On Eagle V3M with RDACM20
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GMSL serial data bus width is normally selected through the BWS pin.
On some systems, the pin may not be wired to the correct value. Support
overriding the bus width by software, using the value specified in the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Read the maxim,i2c-clock-frequency DT property that specifies the speed
of the remote I2C bus, and configure the MAX9286 accordingly. The remote
serializers must all have a matching configuration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for 12-bit raw bayer formats to the driver, configuring the
GMSL format accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286_DATATYPE_RAW11 value is used to configure the MAX9286 for
11-bit or 12-bit input data. While 11-bit data is supported on the GMSL
side, CSI-2 doesn't have a RAW11 format. 11-bit data is transferred over
CSI-2 as RAW12. Rename the macro accordingly to avoid confusion.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286 can generate a framesync signal to synchronize the cameras,
using an internal timer. Support this mode of operation and configure it
through the .s_frameinterval() operation. If the frame interval is not
0, framesync is switched to manual mode with the specified interval,
otherwise automatic mode is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow users to use one PoC regulator per port, instead of a global
regulator.
The properties '^port[0-3]-poc-supply$' in the DT node are used to
indicate the regulators for individual ports.
Signed-off-by: Thomas Nizan <tnizan@witekio.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The MAX9286 has sink pads, so it should implement .link_validate(). Do
so.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The 'maxim,gpio-poc' property is used when the remote camera
power-over-coax is controlled by one of the MAX9286 gpio lines,
to instruct the driver about which line to use and what the line
polarity is.
Add to the max9286 driver support for parsing the newly introduced
property and use it if available in place of the usual supply, as it is
not possible to establish one as consumer of the max9286 gpio
controller.
If the new property is present, no gpio controller is registered and
'poc-supply' is ignored.
In order to maximize code re-use, break out the max9286 gpio handling
function so that they can be used by the gpio controller through the
gpio-consumer API, or directly by the driver code.
Wrap the power up and power down routines to their own function to
be able to use either the gpio line directly or the supply. This will
make it easier to control the remote camera power at run time.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the dev_err_probe() helper, instead of open-coding the same
operation. While at it retrieve the error once and use it from
'ret' instead of retrieving it twice.
Link: https://lore.kernel.org/linux-media/20211208121756.3051565-1-niklas.soderlund+renesas@ragnatech.se
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas S\xF6derlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename V4L2 async notifier functions, replacing "notifier" with "nf" and
removing "_subdev" at the end of the function names adding subdevs as you
can only add subdevs to a notifier. Also wrap and otherwise clean up long
lines.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (imx7)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rephrase a comment in .bound() callback to make it clear we register
a subdev notifier and remove a redundant comment about disabling i2c
auto-ack.
No functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Provide a macro to define the reverse channel amplitude to
be used to compensate the remote serializer noise immunity.
While at it, update a comment.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cache the current channel amplitude in a driver variable
to skip updating it if the newly requested value is the same
as the currently configured one.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the reverse_channel_mv variable to init_rev_chan_mv as
the next patch will cache the reverse channel amplitude in
a new driver variable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adjust the initial reverse channel amplitude parsing from
firmware interface the 'maxim,reverse-channel-microvolt'
property.
This change is required for both rdacm20 and rdacm21 camera
modules to be correctly probed when used in combination with
the max9286 deserializer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instrument the function that configures the reverse channel with a
programmable amplitude value.
This change serves to prepare to adjust the reverse channel amplitude
depending on the remote end high-threshold configuration.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break out the reverse channel setup configuration procedure to its own
function.
This change prepares for configuring the reverse channel conditionally
to the remote side high threshold configuration.
No functional changes intended.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesasa@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the max9286 driver embeds it in the max9286_source
structure. This causes memory corruption when the notifier is destroyed
at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally. A new max9286_asd structure is introduced, to store a
pointer to the corresonding max9286_source that needs to be accessed
from bound and unbind callbacks. There's no need to take an extra
explicit reference to the fwnode anymore as
v4l2_async_notifier_add_fwnode_subdev() does so internally.
While at it, use %u instead of %d to print the unsigned index in the
error message from the v4l2_async_notifier_add_fwnode_subdev() error
path.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the error return from the call to max9286_read is masked
with 0xf0 so the following check for a negative error return is
never true. Fix this by checking for an error first, then masking
the return value for subsequent conflink_mask checking.
Addresses-Coverity: ("Logically dead code")
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 is a 4-channel GMSL deserializer with coax or STP input and
CSI-2 output. The device supports multicamera streaming applications,
and features the ability to synchronise the attached cameras.
CSI-2 output can be configured with 1 to 4 lanes, and a control channel
is supported over I2C, which implements an I2C mux to facilitate
communications with connected cameras across the reverse control
channel.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
