Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_crop.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_audio.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_jpegcomp.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of old drivers still had the experimental tag. Time to remove it.
It concerns the following drivers:
VIDEO_TLV320AIC23B
USB_STKWEBCAM
VIDEO_CX18
VIDEO_CX18_ALSA
VIDEO_ZORAN_AVS6EYES
DVB_USB_AF9005
MEDIA_TUNER_TEA5761
VIDEO_NOON010PC30
This decision was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If start_streaming() fails (e.g. out of memory) the driver needs to
rewind the start procedure. This implies possibly stopping the device
and clearing the buffer queue.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver was expecting to get a valid pixelformat on s_fmt and try_fmt.
This is wrong, since the user may pass a bitmask and expect the driver
to change it, returning a valid (fourcc) pixelformat.
This problem was spotted by v4l2-compliance.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When an urb buffer can't be allocated, the currently allocated
buffer count must be saved so they can properly released.
Moreover, it's sufficient to call stk1160_free_isoc to have
all urb buffers released.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is just a cleaning patch to produce more useful
debug messages.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Plain '-1' is not very good error code. Use more suitable error
code definitions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use .get_if_frequency() as all used tuner drivers
(mt2060/qt1010/mxl5005s) supports it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not good idea to return error for missing callback
handler as whole callback as optional and could be missing
by intentionally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is first step closer to support multiple tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add the toggle bit to the tt3650_rc_query function of the ttusb2
driver.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit da35de640 broke compilation, as it reverted the name of the
usb card free function.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we fail to set up the capture device we go through negative indexes and
badness happens. Add the missing test.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44551
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It needs the e4000 tuner driver.
Signed-off-by: Philipp Dreimann <philipp@dreimann.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not allowed to call usb_clear_halt() after urbs are submitted.
That causes oops sometimes. Move whole streaming_ctrl() logic to
power_ctrl() in order to avoid wrong usb_clear_halt() use. Also,
configuring streaming endpoint in streaming_ctrl() sounds like a
little bit wrong as it is aimed for control stream gate.
Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since ifnum is not used anywhere it is safe to remove it.
This was spotted by Hans's media_tree daily build.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct vb2_queue is allocated through kzalloc as part of a larger struct,
there's no need to clear it.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After qt1010 change that device seems to survive from reset resume.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is workaround / partial fix.
rtl2832u_power_ctrl() and rtl2832u_frontend_attach() needs to
be go through carefully and fix properly. There is clearly
some logical errors when handling power-management ang GPIOs...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stream did not start anymore after stream was stopped once.
Following error can be seen, xhci_hcd
WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
usb_clear_halt for streaming endpoint helps.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver now supports USERPTR, and isn't limited to YUYV and
MJPEG anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to call the image quality adjustment functions in sd_start.
The gspca main driver calls v4l2_ctrl_handler_setup in gspca_init_transfer,
which already applies all image control values.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current white balance temperature default value is 4, which is much too small (possible values are 0-255).
Improve the picture quality by increasing the default value to 55, which is the default value used by the Windows driver.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver uses page 0 register 0xb6 for sharpness adjustment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression from kernel 3.4 which has been introduced with the conversion of the gspca driver to the v4l2 control framework.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) We always re-create the input-urb on resume, so we must also always
destroy it on suspend to avoid leaking it
2) If we're going to do an init_transfer, then that will destroy the urb
before starting the stream (nop if there is none), and (re-)create it
once the stream is started. So there is little use in creating it, if
we're going to do an init_transfer immediately afterward
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_main: init_transfer does not do anything between calling sd_start
(which starts the workqueue) and releasing the usb_lock, so this
synchronization is a nop, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
