Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
If path_rec_start() returns error, call path_free() only if the path
was newly-created. If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.
The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).
Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status. In that case, don't print an error
message unless multicast debugging is enabled.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a deadlock between child interface creation/deletion and ipoib
start/stop. The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev(). The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.
Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL. We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().
Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.
Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup). This
will cause the system to be a member of the broadcast group when
interface is down. As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost. In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first. When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists. It will not have an AH
either, because of sender-side failover. Therefore, it will not get
an AH when the path is resolved.
The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid. Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace all uses of IPOIB_GID_FMT, IPOIB_GID_RAW_ARG() and IPOIB_GID_ARG()
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a get_rx_csum method. Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_ib_dev_stop() does del_timer_sync(&priv->poll_timer), but if a
P_key for an interface is not found, poll_timer is not initialized, so
this leads to a crash or hang. Fix this by moving where poll_timer is
initialized to ipoib_ib_dev_init(), which is always called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1172>.
Debugged-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, IPoIB is an LLTX driver that uses its own IRQ-disabling
tx_lock. Not only do we want to get rid of LLTX, this actually causes
problems because of the skb_orphan() done with this tx_lock held: some
skb destructors expect to be run with interrupts enabled.
The simplest fix for this is to get rid of the driver-private tx_lock
and stop using LLTX. We kill off priv->tx_lock and use
netif_tx_lock[_bh]() instead; the patch to do this is a tiny bit
tricky because we need to update places that take priv->lock inside
the tx_lock to disable IRQs, rather than relying on tx_lock having
already disabled IRQs.
Also, there are a couple of places where we need to disable BHs to
make sure we have a consistent context to call netif_tx_lock() (since
we no longer can use _irqsave() variants), and we also have to change
ipoib_send_comp_handler() to call drain_tx_cq() through a timer rather
than directly, because ipoib_send_comp_handler() runs in interrupt
context and drain_tx_cq() must run in BH context so it can call
netif_tx_lock().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event. This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL. A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).
Fix this by updating path->ah and freeing old_ah only when the path
record query is successful. This prevents the neighbour AH and that
path AH from getting out of sync.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>
Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop(). We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly. This
works because we only flush the ipoib_workqueue with the RTNL not held.
The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes. This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().
This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device
flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which
is run from the ipoib_workqueue. However, ipoib_stop() (which is run
inside rtnl_lock()) flushes this workqueue, which leads to a deadlock
if the join task is pending.
Fix this by simply not flushing the workqueue from ipoib_stop(). It
turns out that we really don't care about workqueue tasks running
during or after ipoib_stop(), as long as we make sure to flush the
workqueue before unregistering a netdev.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1114>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are users that are running UDP applications that require a large
receive queue size in order to get good performance. To prevent
allocation failures for rx_rings when using non-SRQ mode and large
recv_queue_size (1K or larger), use vmalloc() instead of kcalloc() to
alocate rx_rings.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->sg_list should be set to the sge pointer passed in, not
priv->cm.rx_sge.
Reported-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs,"
which no longer exists. Correct this to talk about the files under
debugfs that are really created.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connected mode is now tested and used by lots of people. No need to
hide it under CONFIG_EXPERIMENTAL.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_sa_path_rec_get() if it fails to help
debug errors.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks. With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput. Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array. Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice. Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use of this lock is required to synchronize changes to the netdvice's
data structs. Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function old new delta
ipoib_mcast_leave 357 319 -38
ipoib_mcast_detach 67 - -67
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code will set the Q_Key for any join of a non-sendonly
multicast group. The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group. Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPOIB_MCAST_STARTED flag is not used at all since commit b3e2749b
("IPoIB: Don't drop multicast sends when they can be queued"), so
remove it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.
The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level. In most cases, SM
failover doesn't cause LID change so traffic won't stop. In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state. In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated. Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device. This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.
Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().
Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow. It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU. This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB. The newly allocated SKB is passed to the stack and the
old SKB is reposted.
When running netperf, UDP small messages, without this pach I get:
UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
14.4.3.178 (14.4.3.178) port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
114688 128 10.00 5142034 0 526.31
114688 10.00 1130489 115.71
With this patch I get both send and receive at ~315 mbps.
The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced. As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs. So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted. Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets. This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):
tx packets
==========
port counter: 1,543,996
ifconfig: 1,581,426
netperf: 5,142,034
rx packets
==========
netperf 1,1304,089
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
