The selected 4930G model seemed to keep the subwoofer 'tuba'
function from operating correctly. Removing the existing PCI
ID match made this work again, but it was mapped to 'Side'
instead of to LFE as one would expect.
This attempts to enable all functionality and keep the amount
of available mixer sliders low. Any slider that had no audible
effect on the output audio has been removed, and as such EAPD
is not currently enabled.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These drivers aren't BF52x specific, so don't use bf52x in the names.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Latest ASoC only passes snd_soc_dai to the resume function.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Do not let the SPORT be reconfigured until there are no more active
streams. Then we can let the system reprogram the SPORT state.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to define second copies of mode and format, they're declared
with exactly the same type at the head of the function and there's no
conflict in their use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add basic support for integration with the regulator API to WM8580.
Since the core cannot yet disable biases when the CODEC is idle we
simply request and enable the regulators for the entire time the
driver is active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Seems that nobody recently tried the input on the very first supported
sound card model, RK2. This patch fixes the byte offset to make it
running again.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the use of BUS_ID_SIZE from txx9aclc.c, as BUS_ID_SIZE will be
removed soon later.
Also, use snprintf() instead of sprintf() as a safer operation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct some cut+paste typos from 'tagra' to 'targa'.
Signed-off-by: Sasha Alexandr <brina_keith@ns.sympatico.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
The wm8731 driver has been converted to register using the standard I2C
device registration mechanism so we can now do the registration in the
arch/arm code as normal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support to the sound core to report the proper device name to
userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch mostly follows commit 5998102b90
"ASoC: Refactor WM8731 device registration" to make UDA1380 use standard
device instantiation. Similarly, the I2C device registration temporarily
moves into the magician machine driver before it will find its final
resting place in the board file.
At the same time, platform specific configuration is moved to platform data
and common power/reset GPIO handling moves into the codec driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PCM x-fi native update routine can cause deadlocks when the
trigger(START) is called while the stream is running.
This patch fixes the deadlock by just postponing the pcm period update
to the next possible wake-up. Also it adds the flip of ti->running
flag (just to be sure as now).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM pointer callback sometimes returns invalid positions and this
screws up the hw_ptr updater in PCM core. Especially since now the
jiffies check is optional with xrun_debug, the invalid position is
handled as is, and causes serious sound skips, etc.
This patch simplifies the position-fix strategy in intel8x0 to be more
robust:
- just falls back to the last position if bogus position is detected
- another sanity check for the backward move of the position due to
a race of register update and the base-index update
This patch is applicable also for 2.6.30.
Tested-by: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes yet again the ID for the TTA cards, resulting in a
more reasonable name:
1 [Aureon51MkII ]: USB-Audio - Aureon5.1MkII
TerraTec Aureon5.1MkII at usb-0000:00:03.0-2, full speed
Signed-off-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
Follow-up fix needed since "ASoC: pxa-ssp.c fix clock/frame invert".
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the recent changes to the DAPM power checks it has become important
to explicitly instantiate all widgets but some drivers were forgetting
to do that. Since everything needs to do it add a call to instantiate
them immediately before the card registration - it does no harm when it
is called repeatedly and saves work in drivers.
Tested-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that ASoC subdevices can be regular devices they can have normal
suspend and resume calls from their buses. However, suspending them
individually is not desirable since this can lead to problems such as
pops and clicks from devices being suspended with their signals being
amplified or clocks being stopped suddenly.
This will be resolved by having the normal device model suspend and
resume calls call into ASoC which will suspend the entire card while any
of its components are suspended. At present this is not yet implemented
but in order to aid the transition of drivers to the standard device
model this patch adds API calls for the notifications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be enabled
below 24kHz and not enabled above that so remove the user visible
control for this and do it autonomously in the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be
enabled below 24kHz and not enabled above that so remove the
user visible control for this and do it autonomously in the
driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be
enabled below 24kHz and not enabled above that so remove the
user visible control for this and do it autonomously in the
driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Blackfin submission was done as a patch against a different tree
and contained a duplicate hunk which will cause us to loose track of the
substream pointers when shutting down. Remove one of the duplicated
hunks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spinlock in atc can cause a sleep in lock:
Kernel failure message 1:
BUG: sleeping function called from invalid context at mm/slub.c:1599
in_atomic(): 0, irqs_disabled(): 1, pid: 2537, name: gstreamer-prope
Pid: 2537, comm: gstreamer-prope Tainted: P
2.6.29.4-167.fc11.x86_64 #1
Call Trace:
[<ffffffff8103ff0f>] __might_sleep+0x10b/0x110
[<ffffffff810cd734>] __kmalloc+0x73/0x130
[<ffffffffa0b4b142>] ? daio_rsc_init+0xaa/0x125 [snd_ctxfi]
[<ffffffffa0b4b212>] dao_rsc_init+0x55/0x1c0 [snd_ctxfi]
[<ffffffffa0b4b3d2>] dao_rsc_reinit+0x55/0x5d [snd_ctxfi]
[<ffffffff813abd6c>] ? _spin_lock_irqsave+0x32/0x3b
[<ffffffffa0b454fe>] atc_spdif_out_passthru+0x92/0x136 [snd_ctxfi]
...
Since the lock path is no critical path, it can be gracefully
replaced with a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for Zoom2 board. Zoom2 machine driver
connects both codec DAIs (audio and voice) to omap3
McBSP ports in the following way:
HiFi <-> McBSP2
Voice <-> McBSP3
The zoom2 driver has the following DAPM widgets:
* Ext Mic: MAINMIC, SUBMIC (with bias)
* Ext Spk: HFL, HFR
* Headset Stereophone: HSOL, HSOR
* Headset Mic: HSMIC (with bias)
* Aux In: AUXL, AUXR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (290 commits)
ALSA: pcm - Update document about xrun_debug proc file
ALSA: lx6464es - support standard alsa module parameters
ALSA: snd_usb_caiaq: set mixername
ALSA: hda - add quirk for STAC92xx (SigmaTel STAC9205)
ALSA: use card device as parent for jack input-devices
ALSA: sound/ps3: Correct existing and add missing annotations
ALSA: sound/ps3: Restructure driver source
ALSA: sound/ps3: Fix checkpatch issues
ASoC: Fix lm4857 control
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: usb - Add boot quirk for C-Media 6206 USB Audio
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: emu10k1 - Fix minimum periods for efx playback
...
These are not supported since performance can not be guaranteed
when they are in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The WM8961 is a low power, high quality stereo CODEC designed for
portable digital applications with headphone and stereo class D speaker
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a trivial patch that removes an unnecessary void pointer cast.
Signed-off-by: Chris Sanford <crsanford@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just for the sake of readability, removing extra space
Signed-off-by: Viral Mehta <viral.mehta@einfochips.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* We don't need to write the registers twice, remove the first write.
* DAIFMT_INV switch is duplicated inside DAIFMT_FORMAT switch, move it
out.
(This patch is for Mark's for-2.6.32 branch, I have not checked if the
code is duplicated on current 2.6.30)
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
trivial patch to support the alsa module parameters `index', `id'
and `enable'
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
alsamixer and friends want the mixername to be set. Even though the
driver does not exports a real mixer device, export the name doesn't
harm.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This moves the jack devices from the PCI device into the ALSA card device, which
makes it easier for userspace to find all devices belonging to a specific card
while granting access to logged-in users.
Jack input devices from sound cards can now simply be matched with udev by doing:
SUBSYSTEM="input", SUBSYSTEMS="sound", ...
ls -l /sys/devices/pci0000:00/0000:00:1b.0/sound/card0
controlC0
device -> ../../../0000:00:1b.0
id
input10
input11
input8
input9
number
pcmC0D0c
pcmC0D0p
pcmC0D1p
power
subsystem -> ../../../../../class/sound
uevent
Cc: Lennart Poettering <lennart@0pointer.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort includes, and reorder code so we can kill the forward declarations
No functional changes
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 4eaa9819dc changed semantics of
private_value member of kcontrol. This resulted in inability to control
amplifier and subsequently in very low output volume.
Tested-by: Johannes Schauer <josch@pyneo.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* topic/pcm-jiffies-check:
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: pcm - Fix update of runtime->hw_ptr_interrupt
ALSA: pcm - Fix a typo in hw_ptr update check
ALSA: PCM midlevel: lower jiffies check margin using runtime->delay value
ALSA: PCM midlevel: Do not update hw_ptr_jiffies when hw_ptr is not changed
ALSA: PCM midlevel: introduce mask for xrun_debug() macro
ALSA: PCM midlevel: improve fifo_size handling
* topic/oxygen:
sound: virtuoso: add Xonar Essence ST support
sound: virtuoso: enable HDAV S/PDIF input
sound: virtuoso: add another DX PCI ID
sound: oxygen: reset DMA when stream is closed
* topic/misc:
ALSA: sgio2audio.c: clean up checking
ALSA: burgundy: timeout message is off by one.
ALSA: bt87x - Add a quirk entry for Askey Computer Corp. MagicTView'99
ALSA: parisc/harmony: fix printk format warning
ALSA: keywest: Get rid of useless i2c_device_name() macro
* topic/maya44:
ALSA: ice1724 - Add ESI Maya44 support
ALSA: ice1724 - Allow spec driver to create own routing controls
ALSA: ice1724 - Add PCI postint to reset sequence
ALSA: ice1724 - Clean up definitions of DMA records
ALSA: ice1724 - Check error in set_rate function
* topic/core-id-check:
ALSA: Core - clean up snd_card_set_id* calls and remove possible id collision
ALSA: Fix double locking of card list in snd_card_register()
* topic/asoc: (135 commits)
ASoC: Apostrophe patrol
ASoC: codec tlv320aic23 fix bogus divide by 0 message
ASoC: fix NULL pointer dereference in soc_suspend()
ASoC: Fix build error in twl4030.c
ASoC: SSM2602: assign last substream to the master when shutting down
ASoC: Blackfin: document how anomaly 05000250 is handled
ASoC: Blackfin: set the transfer size according the ac97_frame size
ASoC: SSM2602: remove unsupported sample rates
ASoC: TWL4030: Check the interface format for 4 channel mode
ASoC: TWL4030: Use reg_cache in twl4030_init_chip
ASoC: Initialise dev for the dummy S/PDIF DAI
ASoC: Add dummy S/PDIF codec support
ASoC: correct print specifiers for unsigneds
ASoC: Modify mpc5200 AC97 driver to use V9 of spin_event_timeout()
ASoC: Switch FSL SSI DAI over to symmetric_rates
ASoC: Mark MPC5200 AC97 as BROKEN until PowerPC merge issues are resolved
ASoC: Fabric bindings for STAC9766 on the Efika
ASoC: Support for AC97 on Phytec pmc030 base board.
ASoC: AC97 driver for mpc5200
ASoC: Main rewite of the mpc5200 audio DMA code
...
Currently the PCM resources are allocated only once and ever in prepare
callback, assuming that the PCM parameters are never changed. But it's
not true.
This patch adds the call of atc->pcm_release_resources() at hw_params
and hw_free callbacks to assure that the PCM setup is done correctly
for each h/w parameter changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SRC instances may not exist when PCM pointer callback is called at
the state before initialization is finished. Add the NULL check just
to be sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added use_system_timer module option to force to use the system timer
instead of emu20k1 timer irq for debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added boot quirk for C-Media CM6206 device in snd_usb_audio_probe.
The function snd_usb_cm6206_boot_quirk sets up six internal 16-bit
registers in order to initialize the device. Values for the registers
came from sniffing USB traffic under Windows since only four of the six
are documented in the datasheet for CM106 and some reserved bits were
also being set.
[Minor coding-style fixes by tiwai]
Signed-off-by: Dan Allongo <gongo2k1@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CTUAA should be checked instead of CTHENDRIX. The latter is for 20k2 chip.
Also, fixed the detection of UAA/HENDRIX models by fixing the mask bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up probe routines and model detection routines so that the driver
won't call and check the PCI subsystem id at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added 7.1 support for MSI GX620 and jack quirk.
Reference: kernel bug#13430
http://bugzilla.kernel.org/show_bug.cgi?id=13430
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Assign proper errors when platform resource claims fail.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
EFX playback stream should have periods_min = 2 to avoid the buffer
position overflow (due to restrictions of the pcm-indirect helper).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Clean up Hungarian coding style
- Don't use static variables for I2C information; this unables to use
multiple instances. Now they are stored in struct hw20k2 fields.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They are now only accessed within dapm_power_widgets() so can be local
to that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle gain ramping for PGAs so we can coalesce their power updates too.
This is not ideal since we can't cope properly with gain ramping for
stereo paths but that was the case without coalescing and gain ramping
is relatively infrequently used so the effects are limited.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The more flexible value muxes and named mixers don't need to be sorted
differently from a power management point of view, they are different
only in terms of the control interface and not in terms of seqencing
behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reduce the number of register writes we need to set the power state for
a CODEC by coalescing updates to widgets with the same sequence order and
same register into a single write.
This can be a noticable performance improvement with slow or heavily
contended control buses, such as I2C controllers with a low clock
frequency, and is particularly noticable when resuming. It can also
reduce the noticability of and pops and clicks by ensuring that left
and right channels are powered simultaneously if they are in the same
register.
Currently widgets that have events are not coalesced, including PGAs
which may use the volume ramping control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize the timer update routine to look up wall clock once instead of
checking the position of each stream at each timer update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the remaining unsigned shorts with unsigned ints.
Tested with pcap2 codec (25 bits registers).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch does the following:
(1) Add support for the DM646x machine
(2) Modifications required to introduce the platform driver model to get
platform data for all the machines including dm355 and dm644x.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds driver support for the two instances of McASP on TI's DM646x.
The multichannel audio serial port (McASP) functions as a general-purpose audio
serial port optimized for the needs of multichannel audio application.
(http://www.ti.com/litv/pdf/spruer1b).
There are two instances of McASP on DM646x. The McASP0 module includes up to 4
serializers that can be individually enabled to either transmit or receive
in different modes. The McASP1 module is limited with only 1 pinned-out
serializer that can be enabled to only transmit in DIT mode (neither receiving
in any mode nor transmitting in either Burst or TDM mode is supported).
McASP0 consists of transmit and receive sections that may operate
synchronized, or completely independently with separate master clocks, bit
clocks, and frame syncs, and using different transmit modes with different
bit-stream formats.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce the platform driver model to get platform data for dm355 and dm644x.
Register platform driver and acquire the resources in the probe function Since
the platform specific code had been moved from machine driver to dm<soc>.c
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lump the list walk into a single function, and pull in the power
application too so we can do some further refactoring. Pure code
motion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the past the DAPM power sequencing was done by iterating over the list
of widgets once for each widget type and powering widgets of that type.
Instead of doing that do the sorting at the time we insert the widgets
into the lists of widgets to apply power changes to. This reduces the
amount of computation required for seqencing still further, though the
costs are generally dwarfed by the costs of the register writes
implementing them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 13f040f9e5 made another
regression, the missing update of runtime->hw_ptr_interrupt.
Since this field is only checked in snd_pcmupdate__hw_ptr_interrupt(),
not in snd_pcm_update_hw_ptr(), it must be updated before the hw_ptr
change check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
vfree() does it's own 'NULL' check,so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a typo in the commit 13f040f9e5
ALSA: PCM midlevel: Do not update hw_ptr_jiffies when hw_ptr is not changed
which causes obvious problems with PA.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some code analyzer software mistakenly gives
divide by 0 error messages for these lines.
This patch will end its confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Use static tables instead of assigining each funciton pointer
- Add __devinit* to appropriate places; pcm, mixer and timer cannot be
marked because they are kept in the function table that lives long
- Move create_alsa_devs function out of struct ct_atc to mark it
__devinit
Signed-off-by: Takashi Iwai <tiwai@suse.de>
emu20k1 has a native timer interrupt based on the audio clock, which
is more accurate than the system timer (from the synchronization POV).
This patch adds the code to handle this with multiple streams.
The system timer is still used on emu20k2, and can be used also for
emu20k1 easily by changing USE_SYSTEM_TIMER to 1 in cttimer.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAA-mode check in hwct20k1.c is implemented with the endian-dependent
codes. Fix to be more portable (and readable).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case the initalization of an soc_device failed, there is no codec
associated with it. soc_suspend() will still dereference the pointer
and cause an Ooops when entering the sleep mode.
This happens on our board with a multi-target kernel image when booted
on a machine without audio circuits.
This patch makes the code bail out very early in this special case.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
3 ISA sound drivers lack their __devexit_p() markers, which would
cause build failures when the kernel is built without hotplug support.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the (likely cut-n-paste) error by commit
16a30fbb0d, which causes the error below:
sound/soc/codecs/twl4030.c: In function 'twl4030_read_reg_cache':
sound/soc/codecs/twl4030.c:152: error: 'cache' undeclared (first use in this function)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move locking outside snd_card_set_id_internal() function and rename it
to snd_card_set_id_no_lock() for better function description.
User defined id is just copied to card structure at allocation time.
The real unique id procedure is called in snd_card_register() to
ensure real atomicity.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The introduction of snd_card_set_id() added a lock on the card list
to the old choose_default_id() function when using it to implement
the new API call. This lock is needed to allow us to walk the list
and check to see if our new name is a duplicate. Unfortunately this
causes a lockup when called from snd_card_register() (in cases
where no ID is supplied for the card) since the card list is already
locked there.
Fix this fairly hideously by factoring out the implementation and
using a flag to indicate if the lock should be held. A better fix
would probably be to refactor snd_card_register() to move the
_set_id() outside the locking region but I can't immediately see
anything I can convince myself is safe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes crash when shutting down.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[I am not sure if this is the correct approach as I don't know if any of
this actual hardware or drivers are really hot pluggable.]
Gets rid of these build warnings:
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x5c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_new()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_new().
If .snd_pmac_new is only used by .snd_pmac_probe then
annotate .snd_pmac_new with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x10c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_burgundy_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_burgundy_init().
If .snd_pmac_burgundy_init is only used by .snd_pmac_probe then
annotate .snd_pmac_burgundy_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x164): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_daca_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_daca_init().
If .snd_pmac_daca_init is only used by .snd_pmac_probe then
annotate .snd_pmac_daca_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x1dc): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_tumbler_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_tumbler_init().
If .snd_pmac_tumbler_init is only used by .snd_pmac_probe then
annotate .snd_pmac_tumbler_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x1ec): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_tumbler_post_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_tumbler_post_init().
If .snd_pmac_tumbler_post_init is only used by .snd_pmac_probe then
annotate .snd_pmac_tumbler_post_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x28c): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_awacs_init()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_awacs_init().
If .snd_pmac_awacs_init is only used by .snd_pmac_probe then
annotate .snd_pmac_awacs_init with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x2bc): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_pcm_new()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_pcm_new().
If .snd_pmac_pcm_new is only used by .snd_pmac_probe then
annotate .snd_pmac_pcm_new with a matching annotation.
WARNING: sound/ppc/snd-powermac.o(.devinit.text+0x2f8): Section mismatch in reference from the function .snd_pmac_probe() to the function .init.text:.snd_pmac_attach_beep()
The function __devinit .snd_pmac_probe() references
a function __init .snd_pmac_attach_beep().
If .snd_pmac_attach_beep is only used by .snd_pmac_probe then
annotate .snd_pmac_attach_beep with a matching annotation.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cut'n'paste mistake, whose likely result was nothing at all.
Correct version is "USB_DEVICE", not "USB_DEVICE_VENDOR_SPEC".
Signed-off-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If not passed as module option, provide an own card ID with the newly
introduced snd_set_card_id() call.
This will prevent ALSA from calling choose_default_name() which only
takes the last part of a name containing whitespaces. This for example
caused 'Audio 4 DJ' to be shortened to 'DJ', which was not very
descriptive.
The implementation now takes the short name and removes all whitespaces
from it which is much nicer.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce snd_card_set_id() function to allow lowlevel drivers to set
default identification name for card slot. The function checks also
for identification name collisions and tries to create unique name.
Also, the snd_card_create() function is simplified, because this new
function is used. As bonus, proper name collision checks are evaluated
at the card create time.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The serial number is of no interest in the longname, remove it. This
gives space for the usb path information which is more informative.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, LG R510 is only able to produce sound on headphones, the
internal speakers are not working.
The user tested and confirmed that with model=Dell headphones,
internal speakers and the microphone are working flawlessly.
Tested-by: Serdar Soytetir <tulliana@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a patch against current snapshot that adds:
6 channels support for the MB5 model
Signed-off-by: Kacper Szczesniak <kacper@qwe.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In addition to the operating mode check, also check the
codec's interface format in case of four channel mode.
If the codec is not in TDM (DSP_A) mode, return with error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix issues for 3 generations of HP workstations.
The modest modifications do the following:
1. Change the second MIC from device 3 to device 1
2. Init the "boost" values to "0" by default
From: John Brown <john.brown3@hp.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a half-working quirk for Roland/Edirol M-16DX.
This enables the capture on the device but the playback on it seems still
problematic becuase of lack of sync with the capture clock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirk to provide proper naming of the Terratec Aureon 5.1 MkII
USB card.
Signed-off-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the codec->reg_cache instead of the array directly
in twl4030_init_chip for setting the default values.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of mangling the CONFIG_* variables in the makefiles over and
over, set a few helper variables in Kconfig.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When hardware has large FIFO, it is necessary to lower jiffies margin
by count of queued samples.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some hardware might have bigger FIFOs and DMA pointer value will be updated
in large chunks. Do not update hw_ptr_jiffies and position timestamp when
hw_ptr value was not changed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For debugging purposes, it is better to separate actions.
Bit-values:
1: show bad PCM ring buffer pointer
2: show also stack (to debug kernel latency issues)
4: check pointer against system jiffies
Example:
5: show bad PCM ring buffer pointer and do jiffies check
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the fifo_size assignment to hw->ioctl callback to allow lowlevel
drivers overwrite the default behaviour.
fifo_size is in frames not bytes as specified in asound.h and alsa-lib's
documentation, but most hardware have fixed byte based FIFOs. Introduce
internal SNDRV_PCM_INFO_FIFO_IN_FRAMES.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
