This is not something we can do a workaround. It is clearly an error
and we should notify the user that it is an error.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently we only expose to the user the ID of the first available
user interrupt. To make user interrupts allocation truly dynamic, we
need to also expose the number of user interrupts.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add a missing error check in the sysfs show function for max_power.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of soft reset failure, hard reset should be initiated, but
reset flags were not set to enable it, which caused another soft reset
followed by another failure.
Updated reset flags to enable hard reset flow in case of soft reset
failure.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add a missing error check in the sysfs show functions for
clk_max_freq_mhz and clk_cur_freq_mhz_show.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If reading PLL info from F/W fails, the PLL info is not set in the
"result" variable, and hence shouldn't be copied to the caller's array.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Freeing phys_pg_pack includes calling to scrubbing functions of the
device's memory, taking locks and possibly even calling reset.
This is not something that should be done while holding a device-wide
spinlock.
Therefore, save the relevant objects on a local linked-list and after
releasing the spinlock, traverse that list and free the phys_pg_pack
objects.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to support several device MMU blocks with different
architectures (e.g. different HOP table size) we need to move to
per-MMU properties rather than keeping those properties as ASIC
properties.
Refactoring the code to use "per-MMU proprties" is a major effort.
To start making the transition towards this goal but still support
taking the properties from ASIC properties (for code that currently
uses them) this patch copies some of the properties to the "per-MMU"
properties and later, when implementing the per-MMU properties, we
would be able to delete the MMU props from the ASIC props.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In future ASICs, there is no kernel TDR for new workloads that are
submitted directly from user-space to the device.
Therefore, the driver can NEVER know that a workload has timed-out.
So, when the user asks us to wait for interrupt on the workload's
completion, and the wait has timed-out, it doesn't mean the workload
has timed-out. It only means the wait has timed-out, which is NOT an
error from driver's perspective.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Adds new sysfs entry to display firmware os version
/sys/class/habanalabs/hl<n>/fw_os_ver
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We have a common function that wraps the call to the MMU cache
invalidation function, which is ASIC-specific. The wrapper checks
the return value and prints error if necessary. For consistency, try
to use the wrapper when possible.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
infineon version is only applicable to GOYA and GAUDI. For later
ASICs, we display the Voltage Regulator Monitor f/w version.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In this attribute group we are only adding clocks. This is in
preparation for adding a device specific attribute group which is
not related to clocks.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Setting PLL profile is the same for all ASICs, except for GOYA.
However, because this function is never called from common code, there
is no need to have an asic-specific callback function.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For better maintainability, try to concentrate all the common functions
that communicate with the f/w in firmware_if.c
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The two remaining functions in this file belong to firmware_if.c,
as they communicate with the firmware.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Retrieving the clock from the f/w is done exactly the same in ALL our
ASICs. Therefore, no real justification for doing it as an
ASIC-specific function.
The only thing is we need to check if we are running on simulator,
which doesn't require ASIC-specific callback.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Move common sysfs store/show functions to sysfs.c file for
consistency.
This is part of a patch-set to remove hwmgr.c
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some MMU functions can be used by different versions of our MMUs, so
move them to be common.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Now that clock gating is permanently disabled in GAUDI, no need for
the ASIC functions of setting and disabling clock gating, as this
was a unique scenario in GAUDI.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Due to the need of SynapseAI to configure all TPC engines from a single
QMAN, the driver must disable CGM and never allow the user to enable
it. Otherwise, the configuration of the TPC engines will fail.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This patch fixes what seems to be copy paste error.
We will have a memory leak if the host-resident shadow is NULL (which
will likely happen as the DR and HR are not dependent).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As part of handling of the multi-CS wait ioctl, hl_cs_poll_fences() is
called in a "while (true)" loop. This function can fail, but the
checking of its return value was missed.
Add this check and exit the loop in case of a failure.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During the hardware start sequence, do not overwrite the driver state
and do not proceed with the initialization sequence if the state
was changed while the driver was waiting for the start interrupt.
This can happen if the driver's removal/stop procedure was triggered
from the parent level while the driver is waiting for the start
interrupt. This may lead to stray the reset work or the timer
after driver were removed.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20220215080438.264876-4-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid link reset in DISABLED and POWERING_DOWN state
if read error is occurred - let shutdown flow finish.
In any state exit interrupt handler if read error occurred.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20220215080438.264876-3-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid lingering reset thread on driver shutdown.
If the firmware is down during a shutdown flow
do not initiate the link reset, simply disconnect
all clients and let shutdown flow finish
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20220215080438.264876-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a quirk to disable MEI interface on Intel PCH Ignition (IGN)
as the IGN firmware doesn't support the protocol.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20220215080438.264876-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rts522a, rts5228, rts5261
add extra init flow for rtd3
add more power_down setting for avoid being woken up
by plugging or unplugging card when system in S3
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/dace32f573a445908fec0a10482c394c@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memcpy() runtime defenses are still not landed, so test with
strncpy() for now.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220216202548.2093883-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On s390 allyesconfig, there is this build error
rtsx_pcr.c:1084:13: error: 'rtsx_pm_power_saving'
defined but not used
1084 | static void rtsx_pm_power_saving(struct rtsx_pcr *pcr)
| ^~~~~~~~~~~~~~~~~~~~
rtsx_pm_power_saving() is only used by rtsx_pci_runtime_idle()
which is conditional on CONFIG_PM. So conditionally build
rtsx_pm_power_saving() and the similar
rtsx_comm_pm_power_saving() and rtsx_enable_aspm().
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220213171907.2786442-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace "struct list_head head = LIST_HEAD_INIT(head)" with
"LIST_HEAD(head)" to simplify the code.
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220209032421.37725-1-cai.huoqing@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in this particular case (*) it would not be an issue,
the pattern itself is bad and error prone in case somebody
blindly copies to their code.
Don't cast parameter to unsigned long pointer in the bit
operations. Note, new compilers might warn on this line for
potential outbound access.
*) it seems a dead code, so remove it all for good
Fixes: 13d19498b0 ("GRU Driver: driver internal header files")
Acked-by: Dimitri Sivanich <sivanich@hpe.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220214153958.9721-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'err_remove_vmci_dev_g' error label is not at the right place.
This could lead to un-released resource.
There is also a missing label. If pci_alloc_irq_vectors() fails, the
previous vmci_event_subscribe() call must be undone.
Acked-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/959218ce3b135197946d85cd9453551cd04fa5da.1645734041.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Add WRITE_OPD to check that you can't modify function
descriptors.
Gives the following result when function descriptors are
not protected:
lkdtm: Performing direct entry WRITE_OPD
lkdtm: attempting bad 16 bytes write at c00000000269b358
lkdtm: FAIL: survived bad write
lkdtm: do_nothing was hijacked!
Looks like a standard compiler barrier() is not enough to force
GCC to use the modified function descriptor. Had to add a fake empty
inline assembly to force GCC to reload the function descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7eeba50d16a35e9d799820e43304150225f20197.1644928018.git.christophe.leroy@csgroup.eu
execute_location() and execute_user_location() intent
to copy do_nothing() text and execute it at a new location.
However, at the time being it doesn't copy do_nothing() function
but do_nothing() function descriptor which still points to the
original text. So at the end it still executes do_nothing() at
its original location allthough using a copied function descriptor.
So, fix that by really copying do_nothing() text and build a new
function descriptor by copying do_nothing() function descriptor and
updating the target address with the new location.
Also fix the displayed addresses by dereferencing do_nothing()
function descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4055839683d8d643cd99be121f4767c7c611b970.1644928018.git.christophe.leroy@csgroup.eu
WRITE_KERN is supposed to overwrite some kernel text, namely
do_overwritten() function.
But at the time being it overwrites do_overwritten() function
descriptor, not function text.
Fix it by dereferencing the function descriptor to obtain
function text pointer. Export dereference_function_descriptor()
for when LKDTM is built as a module.
And make do_overwritten() noinline so that it is really
do_overwritten() which is called by lkdtm_WRITE_KERN().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/31e58eaffb5bc51c07d8d4891d1982100ade8cfc.1644928018.git.christophe.leroy@csgroup.eu
LKDTM tests display that the run do_nothing() at a given
address, but in reality do_nothing() is inlined into the
caller.
Force it out of line so that it really runs text at the
displayed address.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a5dcf4d2088e6aca47ab3b4c6d5c0f7fa064e25a.1644928018.git.christophe.leroy@csgroup.eu
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into char-misc-next
We need the char/misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Backmerge tag 'v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Daniel asked for this for some intel deps, so let's do it now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the DMA based receive operation instead of the ioread8_rep
based datagram receive when DMA datagrams are supported.
In the receive operation, configure the header to point to the
page aligned VMCI_MAX_DG_SIZE part of the receive buffer
using s/g configuration for the header. This ensures that the
existing dispatch routine can be used with little modification.
Initiate the receive by writing the lower 32 bit of the buffer
to the VMCI_DATA_IN_LOW_ADDR register, and wait for the busy
flag to be changed by the device using a wait queue.
The existing dispatch routine for received datagrams is reused
for the DMA datagrams with a few modifications:
- the receive buffer is always the maximum size for DMA datagrams
(IO ports would try with a shorter buffer first to reduce
overhead of the ioread8_rep operation).
- for DMA datagrams, datagrams are provided contiguous in the
buffer as opposed to IO port datagrams, where they can start
on any page boundary
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-9-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DMA based send operation from the transmit buffer instead of the
iowrite8_rep based datagram send when DMA datagrams are supported.
The outgoing datagram is sent as inline data in the VMCI transmit
buffer. Once the header has been configured, the send is initiated
by writing the lower 32 bit of the buffer base address to the
VMCI_DATA_OUT_LOW_ADDR register. Only then will the device process
the header and the datagram itself. Following that, the driver busy
waits (it isn't possible to sleep on the send path) for the header
busy flag to change - indicating that the send is complete.
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-8-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DMA datagrams are used, allocate send and receive buffers
in coherent DMA memory.
This is done in preparation for the send and receive datagram
operations, where the buffers are used for the exchange of data
between driver and device.
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-7-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tell the device the page size used by the OS.
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-5-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detect the VMCI DMA datagram capability, and if present, ack it
to the device.
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-4-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detect the support for MMIO access through examination of the length
of the region requested in BAR1. If it is 256KB, the VMCI device
supports MMIO access to registers.
If MMIO access is supported, map the area of the region used for
MMIO access (64KB size at offset 128KB).
Add wrapper functions for accessing 32 bit register accesses through
either MMIO or IO ports based on device configuration.
Sending and receiving datagrams through iowrite8_rep/ioread8_rep is
left unchanged for now, and will be addressed in a later change.
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20220207102725.2742-3-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A successful ida_simple_get() should be balanced by a corresponding
ida_simple_remove().
Add the missing call in the error handling path of the probe.
While at it, switch to ida_alloc()/ida_free() instead to
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Fixes: 4f556bc04e ("misc: cardreader: add new Alcor Micro Cardreader PCI driver")
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/918a9875b7f67b7f8f123c4446452603422e8c5e.1644136776.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename struct dma_buf_map to struct iosys_map and corresponding APIs.
Over time dma-buf-map grew up to more functionality than the one used by
dma-buf: in fact it's just a shim layer to abstract system memory, that
can be accessed via regular load and store, from IO memory that needs to
be acessed via arch helpers.
The idea is to extend this API so it can fulfill other needs, internal
to a single driver. Example: in the i915 driver it's desired to share
the implementation for integrated graphics, which uses mostly system
memory, with discrete graphics, which may need to access IO memory.
The conversion was mostly done with the following semantic patch:
@r1@
@@
- struct dma_buf_map
+ struct iosys_map
@r2@
@@
(
- DMA_BUF_MAP_INIT_VADDR
+ IOSYS_MAP_INIT_VADDR
|
- dma_buf_map_set_vaddr
+ iosys_map_set_vaddr
|
- dma_buf_map_set_vaddr_iomem
+ iosys_map_set_vaddr_iomem
|
- dma_buf_map_is_equal
+ iosys_map_is_equal
|
- dma_buf_map_is_null
+ iosys_map_is_null
|
- dma_buf_map_is_set
+ iosys_map_is_set
|
- dma_buf_map_clear
+ iosys_map_clear
|
- dma_buf_map_memcpy_to
+ iosys_map_memcpy_to
|
- dma_buf_map_incr
+ iosys_map_incr
)
@@
@@
- #include <linux/dma-buf-map.h>
+ #include <linux/iosys-map.h>
Then some files had their includes adjusted and some comments were
update to remove mentions to dma-buf-map.
Since this is not specific to dma-buf anymore, move the documentation to
the "Bus-Independent Device Accesses" section.
v2:
- Squash patches
v3:
- Fix wrong removal of dma-buf.h from MAINTAINERS
- Move documentation from dma-buf.rst to device-io.rst
v4:
- Change documentation title and level
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204170541.829227-1-lucas.demarchi@intel.com
Open Profile for DICE is an open protocol for measured boot compatible
with the Trusted Computing Group's Device Identifier Composition
Engine (DICE) specification. The generated Compound Device Identifier
(CDI) certificates represent the hardware/software combination measured
by DICE, and can be used for remote attestation and sealing.
Add a driver that exposes reserved memory regions populated by firmware
with DICE CDIs and exposes them to userspace via a character device.
Userspace obtains the memory region's size from read() and calls mmap()
to create a mapping of the memory region in its address space. The
mapping is not allowed to be write+shared, giving userspace a guarantee
that the data were not overwritten by another process.
Userspace can also call write(), which triggers a wipe of the DICE data
by the driver. Because both the kernel and userspace mappings use
write-combine semantics, all clients observe the memory as zeroed after
the syscall has returned.
Cc: Andrew Scull <ascull@google.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20220126231237.529308-3-dbrazdil@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit effa453168 ("i2c: i801: Don't silently correct invalid transfer
size") revealed that ee1004_eeprom_read() did not properly limit how
many bytes to read at once.
In particular, i2c_smbus_read_i2c_block_data_or_emulated() takes the
length to read as an u8. If count == 256 after taking into account the
offset and page boundary, the cast to u8 overflows. And this is common
when user space tries to read the entire EEPROM at once.
To fix it, limit each read to I2C_SMBUS_BLOCK_MAX (32) bytes, already
the maximum length i2c_smbus_read_i2c_block_data_or_emulated() allows.
Fixes: effa453168 ("i2c: i801: Don't silently correct invalid transfer size")
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20220203165024.47767-1-jonas@protocubo.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the copy back to userland fails for the FASTRPC_IOCTL_ALLOC_DMA_BUFF
ioctl(), we shouldn't assume that 'buf->dmabuf' is still valid. In fact,
dma_buf_fd() called fd_install() before, i.e. "consumed" one reference,
leaving us with none.
Calling dma_buf_put() will therefore put a reference we no longer own,
leading to a valid file descritor table entry for an already released
'file' object which is a straight use-after-free.
Simply avoid calling dma_buf_put() and rely on the process exit code to
do the necessary cleanup, if needed, i.e. if the file descriptor is
still valid.
Fixes: 6cffd79504 ("misc: fastrpc: Add support for dmabuf exporter")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20220127130218.809261-1-minipli@grsecurity.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into char-misc-next
We need the char/misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Use cancel_delayed_work_sync to ensure there's no race with
carddet_work.
- Remove device_wakeup_disable to save some CPU cycles. If the device
really has ACPI _DSW then the wakeup should be disabled in probe
routine.
- Remove fetch_vendor_settings from runtime resume routine, since they
are already saved in "struct rtsx_pcr".
- Move variable assignments to the top of the functions.
Cc: Ricky WU <ricky_wu@realtek.com>
Tested-by: Ricky WU <ricky_wu@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220125055010.1866563-3-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5b4258f672 ("misc: rtsx: rts5249 support runtime PM")
uses "rtd3_work" and "idle_work" to manage it's own runtime PM state
machine.
When its child device, rtsx_pci_sdmmc, uses runtime PM refcount
correctly, all the additional works can be managed by generic runtime PM
helpers.
So consolidate "idle_work" and "rtd3_work" into generic runtime idle
callback and runtime suspend callback, respectively.
Fixes: 5b4258f672 ("misc: rtsx: rts5249 support runtime PM")
Cc: Ricky WU <ricky_wu@realtek.com>
Tested-by: Ricky WU <ricky_wu@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220125055010.1866563-2-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
While at it, include directly <linux/dma-mapping.h> instead on relying on
indirect inclusion.
[1]: https://lkml.org/lkml/2021/6/7/398
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/67ddcec656194153830684e6ff4513114e8859d6.1641624544.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The at25 driver regressed in v5.17-rc1 due to a broken conflict
resolution: the allocation of the object was accidentally removed. Restore
it.
This was found when building under CONFIG_FORTIFY_SOURCE=y and
-Warray-bounds, which complained about strncpy() being used against an
empty object:
In function 'strncpy',
inlined from 'at25_fw_to_chip.constprop' at drivers/misc/eeprom/at25.c:312:2:
./include/linux/fortify-string.h:48:33: warning: '__builtin_strncpy' offset [0, 9] is out of the bounds [0, 0] [-Warray-bounds]
48 | #define __underlying_strncpy __builtin_strncpy
| ^
./include/linux/fortify-string.h:59:16: note: in expansion of macro '__underlying_strncpy'
59 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
In function 'strncpy',
inlined from 'at25_fram_to_chip' at drivers/misc/eeprom/at25.c:373:2,
inlined from 'at25_probe' at drivers/misc/eeprom/at25.c:453:10:
./include/linux/fortify-string.h:48:33: warning: '__builtin_strncpy' offset [0, 9] is out of the bounds [0, 0] [-Warray-bounds]
48 | #define __underlying_strncpy __builtin_strncpy
| ^
./include/linux/fortify-string.h:59:16: note: in expansion of macro '__underlying_strncpy'
59 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/lkml/CAHp75VdqK7h63fz-cPaQ2MGaVdaR2f1Fb5kKCZidUG3RwLsAVA@mail.gmail.com/
Fixes: af40d16042 ("Merge v5.15-rc5 into char-misc-next")
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220118182003.3385019-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Here is the large set of char, misc, and other "small" driver subsystem
changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the full
details.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYeGNAQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoVgCg1CPjMu8/SDj3Sm3a1UMQJn9jnl8AnjQcEp3z
hMr9mISG4r6g4PvjrJBj
=9May
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char, misc, and other "small" driver
subsystem changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the
full details.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
counter: 104-quad-8: Fix use-after-free by quad8_irq_handler
dt-bindings: mux: Document mux-states property
dt-bindings: ti-serdes-mux: Add defines for J721S2 SoC
counter: remove old and now unused registration API
counter: ti-eqep: Convert to new counter registration
counter: stm32-lptimer-cnt: Convert to new counter registration
counter: stm32-timer-cnt: Convert to new counter registration
counter: microchip-tcb-capture: Convert to new counter registration
counter: ftm-quaddec: Convert to new counter registration
counter: intel-qep: Convert to new counter registration
counter: interrupt-cnt: Convert to new counter registration
counter: 104-quad-8: Convert to new counter registration
counter: Update documentation for new counter registration functions
counter: Provide alternative counter registration functions
counter: stm32-timer-cnt: Convert to counter_priv() wrapper
counter: stm32-lptimer-cnt: Convert to counter_priv() wrapper
counter: ti-eqep: Convert to counter_priv() wrapper
counter: ftm-quaddec: Convert to counter_priv() wrapper
counter: intel-qep: Convert to counter_priv() wrapper
counter: microchip-tcb-capture: Convert to counter_priv() wrapper
...
- Optimise radix KVM guest entry/exit by 2x on Power9/Power10.
- Allow firmware to tell us whether to disable the entry and uaccess flushes on Power10
or later CPUs.
- Add BPF_PROBE_MEM support for 32 and 64-bit BPF jits.
- Several fixes and improvements to our hard lockup watchdog.
- Activate HAVE_DYNAMIC_FTRACE_WITH_REGS on 32-bit.
- Allow building the 64-bit Book3S kernel without hash MMU support, ie. Radix only.
- Add KUAP (SMAP) support for 40x, 44x, 8xx, Book3E (64-bit).
- Add new encodings for perf_mem_data_src.mem_hops field, and use them on Power10.
- A series of small performance improvements to 64-bit interrupt entry.
- Several commits fixing issues when building with the clang integrated assembler.
- Many other small features and fixes.
Thanks to: Alan Modra, Alexey Kardashevskiy, Ammar Faizi, Anders Roxell, Arnd Bergmann,
Athira Rajeev, Cédric Le Goater, Christophe JAILLET, Christophe Leroy, Christoph Hellwig,
Daniel Axtens, David Yang, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Guo Ren,
Hari Bathini, Jason Wang, Joel Stanley, Julia Lawall, Kajol Jain, Kees Cook, Laurent
Dufour, Madhavan Srinivasan, Mark Brown, Minghao Chi, Nageswara R Sastry, Naresh Kamboju,
Nathan Chancellor, Nathan Lynch, Nicholas Piggin, Nick Child, Oliver O'Halloran, Peiwei
Hu, Randy Dunlap, Ravi Bangoria, Rob Herring, Russell Currey, Sachin Sant, Sean
Christopherson, Segher Boessenkool, Thadeu Lima de Souza Cascardo, Tyrel Datwyler, Xiang
wangx, Yang Guang.
-----BEGIN PGP SIGNATURE-----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=BxhQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Optimise radix KVM guest entry/exit by 2x on Power9/Power10.
- Allow firmware to tell us whether to disable the entry and uaccess
flushes on Power10 or later CPUs.
- Add BPF_PROBE_MEM support for 32 and 64-bit BPF jits.
- Several fixes and improvements to our hard lockup watchdog.
- Activate HAVE_DYNAMIC_FTRACE_WITH_REGS on 32-bit.
- Allow building the 64-bit Book3S kernel without hash MMU support, ie.
Radix only.
- Add KUAP (SMAP) support for 40x, 44x, 8xx, Book3E (64-bit).
- Add new encodings for perf_mem_data_src.mem_hops field, and use them
on Power10.
- A series of small performance improvements to 64-bit interrupt entry.
- Several commits fixing issues when building with the clang integrated
assembler.
- Many other small features and fixes.
Thanks to Alan Modra, Alexey Kardashevskiy, Ammar Faizi, Anders Roxell,
Arnd Bergmann, Athira Rajeev, Cédric Le Goater, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Daniel Axtens, David Yang, Erhard
Furtner, Fabiano Rosas, Greg Kroah-Hartman, Guo Ren, Hari Bathini, Jason
Wang, Joel Stanley, Julia Lawall, Kajol Jain, Kees Cook, Laurent Dufour,
Madhavan Srinivasan, Mark Brown, Minghao Chi, Nageswara R Sastry, Naresh
Kamboju, Nathan Chancellor, Nathan Lynch, Nicholas Piggin, Nick Child,
Oliver O'Halloran, Peiwei Hu, Randy Dunlap, Ravi Bangoria, Rob Herring,
Russell Currey, Sachin Sant, Sean Christopherson, Segher Boessenkool,
Thadeu Lima de Souza Cascardo, Tyrel Datwyler, Xiang wangx, and Yang
Guang.
* tag 'powerpc-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (240 commits)
powerpc/xmon: Dump XIVE information for online-only processors.
powerpc/opal: use default_groups in kobj_type
powerpc/cacheinfo: use default_groups in kobj_type
powerpc/sched: Remove unused TASK_SIZE_OF
powerpc/xive: Add missing null check after calling kmalloc
powerpc/floppy: Remove usage of the deprecated "pci-dma-compat.h" API
selftests/powerpc: Add a test of sigreturning to an unaligned address
powerpc/64s: Use EMIT_WARN_ENTRY for SRR debug warnings
powerpc/64s: Mask NIP before checking against SRR0
powerpc/perf: Fix spelling of "its"
powerpc/32: Fix boot failure with GCC latent entropy plugin
powerpc/code-patching: Replace patch_instruction() by ppc_inst_write() in selftests
powerpc/code-patching: Move code patching selftests in its own file
powerpc/code-patching: Move instr_is_branch_{i/b}form() in code-patching.h
powerpc/code-patching: Move patch_exception() outside code-patching.c
powerpc/code-patching: Use test_trampoline for prefixed patch test
powerpc/code-patching: Fix patch_branch() return on out-of-range failure
powerpc/code-patching: Reorganise do_patch_instruction() to ease error handling
powerpc/code-patching: Fix unmap_patch_area() error handling
powerpc/code-patching: Fix error handling in do_patch_instruction()
...
Don't blindly copy status value received from the firmware
into internal client status field,
It may be positive and ERR_PTR(ret) will translate it
into an invalid address and the caller will crash.
Put the error code into the client status on failure.
Fixes: 369aea8459 ("mei: implement client dma setup.")
Cc: <stable@vger.kernel.org> # v5.11+
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: : Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20211228082047.378115-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Fixes: 781551df57 ("misc: Add Lattice ECP3 FPGA configuration via SPI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20211228125522.3122284-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field. Move the cxl code to use default_groups field which has been the
preferred way since aa30f47cf6 ("kobject: Add support for default
attribute groups to kobj_type") so that we can soon get rid of the
obsolete default_attrs field.
Cc: Frederic Barrat <fbarrat@linux.ibm.com>
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211228131350.249532-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upper layer may retry call to mei_cl_dma_alloc_and_map(),
in that case the client status may be non-zero after the previous call
and the wait condition will be true immediately.
Set cl->status to zero to allow waiting for an actual result
from the firmware.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20211223094705.204624-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The POWERING_DOWN state string was missing from
the device states list, add it.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20211223094705.204624-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As hard-reset can be requested during soft-reset, driver must allow
it or else critical events received during soft-reset will be
ignored.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Atomic operations during reset are replaced by a spinlock in order
to have the ability to protect more than a single variable.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Unify variables related to device reset, which will help us to
add some new reset functionality in future patches.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This patch fixes issue in which we have timeout for multi-CS although
the CS in the list actually completed.
Example scenario (the two threads marked as WAIT for the thread that
handles the wait_for_multi_cs and CMPL as the thread that signal
completion for both CS and multi-CS):
1. Submit CS with sequence X
2. [WAIT]: call wait_for_multi_cs with single CS X
3. [CMPL]: CS X do invoke complete_all for both CS and multi-CS
(multi_cs_completion_done still false)
4. [WAIT]: enter poll_fences, reinit the completion and find the CS
as completed when asking on the fence but multi_cs_done is
still false it returns that no CS actually completed
5. [CMPL]: set multi_cs_handling_done as true
6. [WAIT]: wait for completion but no CS to awake the wait context
and hence wait till timeout
Solution: if CS detected as completed in poll_fences but multi_cs_done
is still false invoke complete_all to the multi-CS completion
and so it will not go to sleep in wait_for_completion but
rather will have a "second chance" to wait for
multi_cs_completion_done.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In some cases the driver cannot configure ASID of some engines due to
the security level of the relevant registers.
For this a new CPU-CP packet is introduced, which will allow the driver
to ask the F/W to do this configuration instead.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
-ENOTTY is returned in case of error in the ioctl arguments themselves,
such as function that doesn't exists.
In all other cases, where the error is in the arguments of the custom
data structures that we define that are passed in the various ioctls,
we need to return -EINVAL.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current sysfs implementation does not take endianness into
consideration when dumping the cpld version.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently the cq counters are allocated in userspace memory,
and mapped by the driver to the device address space.
A new requirement that is part of new future API related to this one,
requires that cq counters will be allocated in kernel memory.
We leverage the existing cb_create API with KERNEL_MAPPED flag set to
allocate this memory.
That way we gain two things:
1. The memory cannot be freed while in use since it's protected
by refcount in driver.
2. No need to wake up the user thread upon each interrupt from CQ,
because the kernel has direct access to the counter. Therefore,
it can make comparison with the target value in the interrupt
handler and wake up the user thread only if the counter reaches the
target value. This is instead of waking the thread up to copy counter
value from user then go sleep again if target value wasn't reached.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
By the original design we assumed that if we "miss" multi CS completion
it is of no severe consequence as we'll just call wait_for_multi_cs
again.
Sequence of events for such scenario:
1. user submit CS with sequence N
2. user calls wait for multi-CS with only CS #N in the list
3. the multi CS call starts with poll of the CSs but find that none
completed (while CS #N did not completed yet)
4. now, multi CS #N complete but multi CS CTX was not yet created for
the above multi-CS. so, attempt to complete multi-CS fails (as no
multi CS CTX exist)
5. wait_for_multi_cs call now does init_wait_multi_cs_completion (and
for this create the multi-CS CTX)
6. wait_for_multi_cs wits on completion but will not get one as CS #N
already completed
To fix the issue we initialize the multi-CS CTX prior polling the
fences.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As BTL can be replaced by ROM we should modify relevant error print.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During the MMU development the MMU header files were left with unclean
definitions:
- MMU "version specific" definitions that were left in the mmu_general
file
- unused definitions
This patch attempts, where possible, to keep definitions that can serve
multiple MMU versions (but that are not tightly bound with specific MMU
arch) in the mmu_general header file (e.g. different definitions for
number of HOPs).
Otherwise, move MMU version specific definitions (e.g. HOPs masks and
shifts) to the specific MMU version file.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As we allow soft-reset to be performed only on inference devices,
having the sysfs nodes may cause a confusion. Hence, we remove those
nodes on training ASICs.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently sysfs support dumping a single infineon version, in
future asics we will have two infineon versions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Need to allow user retrieve data during reset and afterwards without
the need to reopen the device.
Did it by seperating the user peocesses list into two lists:
1. fpriv_list which contains list of user processes that opened
the device (currently only one).
2. fpriv_ctrl_list which contains list of user processes that opened
the control device. This processes in this list shall not be
killed during reset, only when the device is suddenly removed from
PCI chain.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In legacy f/w that use old hwmon.h file, the values of the hwmon
enums are different than the values that are in newer kernels (5.6
and above).
Therefore, to support working with those f/w, we need to do some
fixup before registering with the hwmon subsystem and also when
calling the functions that communicate with the f/w to retrieve
sensors information.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to increase cpucp messaging reliability we will add
the current PI value to the descriptor sent to F/W.
F/W will wait for the PI value as an indication of a valid packet.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver supports only a single user anyway, so there is no point
in checking whether we are in_debug state when a user tries to open
the device, because if we are in_debug, it means a user is already
using the device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current clock throttling period returned from driver was wrong due
to wrong time comparison.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The original multi-CS design assumption that stream masters are used
exclusively (i.e. multi-CS with set of stream master QIDs will not get
completed by CS not from the multi-CS set) is inaccurate.
Thus multi-CS behavior is now modified not to treat such case as an
error.
Instead, if we have multi-CS completion but we detect that no CS from
the list is actually completed we will do another multi-CS wait (with
modified timeout).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
It was an error to save the compute context's pointer in the device
structure, as it allowed its use without proper ref-cnt.
Change the variable to a flag that only indicates whether there is
an active compute context. Code that needs the pointer will now
be forced to use proper internal APIs to get the pointer.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There are multiple places where the code needs to get the context's
pointer and increment its ref cnt. This is the proper way instead
of using the compute context pointer in the device structure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Pass the user's context pointer into the etr configuration function
to extract its ASID.
Using the compute_ctx pointer is an error as it is just an indication
of whether a user has opened the compute device.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Compute context pointer in hdev shouldn't be used for fetching the
context's pointer.
If an object needs the context's pointer, it should get it while
incrementing its kref, and when the object is released, put it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver supports only a single context. Therefore, no need to check
if the user context that is closed is the compute context. The user
context, if exists, is always the compute context.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix a bug where in case of failure to allocate idr, the handle's
memory wasn't freed as part of the error handling code.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
