Replace kzalloc and clk_get by their managed counterparts to simplify
error and cleanup paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC). Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>. The vender ID is actually
assigned to Applied Micro Circuits Corporation. The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card. Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
A few differences needed by OCTEON:
o These are DWC UARTS, but have USR at a different offset.
o Internal SoC buses require reading back from registers to maintain
write ordering.
o 8250 on OCTEON appears with 64-bit wide registers, so when using
readb/writeb in big endian mode we have to adjust the membase to hit
the proper part of the register.
o No UCV register, so we hard code some properties.
Because OCTEON doesn't have a UCV register, I change where
dw8250_setup_port(), which reads the UCV, is called by pushing it in
to the OF and ACPI probe functions, and move unchanged
dw8250_setup_port() earlier in the file.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5516/
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 8d2f8cd424.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The C8000 workstation (64 bit kernel only) has a somewhat different
serial port configuration than other models.
Thomas Bogendoerfer sent a patch to fix this in September 2010, which
was now minimally modified by me.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Support for the Stallion multiport serial drivers was removed in v3.1.
Clean up their last references in the tree: mainly an outdated Kconfig
entry and unneeded documentation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cfcec52e97.
This regresses a longstanding behaviour on X86 systems, which end up with
PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite
sides of this commit, resulting in the need to constantly modify the console
setting in order to bisect across it.
Please revert, we can work on solving this for ARM platforms in a less
disruptive way.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same controller as on Intel Lynxpoint but the
ACPI ID is different.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffc3ae6dd "serial: 8250_dw: Enable runtime PM" introduced runtime
PM management, which enables/disables the clk without checking if the clk
is valid. However, this driver allows to be probed without a defined clk,
using clock-frequency, as a fallback.
Therefore, on platforms that are device tree probed using clock-frequency
instead of clk, we get an ugly NULL pointer dereference.
This patch fixes it by simply adding a check before accessing the clk api.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver cleanups
as well.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+nSMACgkQMUfUDdst+ymy9QCfRmYn0MC0W+Q1D3Spz87gVsuo
cqEAniu1BEkYZpjAz7ZlIN07Ao0jbQOR
=Osu/
-----END PGP SIGNATURE-----
Merge tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg Kroah-Hartman:
"Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver
cleanups as well.
All of these have been in the linux-next tree for a while"
* tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (117 commits)
tty/serial/sirf: fix MODULE_DEVICE_TABLE
serial: mxs: drop superfluous {get|put}_device
serial: mxs: fix buffer overflow
ARM: PL011: add support for extended FIFO-size of PL011-r1p5
serial_core.c: add put_device() after device_find_child()
tty: Fix unsafe bit ops in tty_throttle_safe/unthrottle_safe
serial: sccnxp: Replace pdata.init/exit with regulator API
serial: sccnxp: Do not override device name
TTY: pty, fix compilation warning
TTY: rocket, fix compilation warning
TTY: ircomm: fix DTR being raised on hang up
TTY: synclinkmp: fix DTR being raised on hang up
TTY: synclink_gt: fix DTR being raised on hang up
TTY: synclink: fix DTR being raised on hang up
serial: 8250_dw: Fix the stub for dw8250_probe_acpi()
serial: 8250_dw: Convert to devm_ioremap()
serial: 8250_dw: Set port capabilities based on CPR register
serial: 8250_dw: Let ACPI code extract the DMA client info
serial: 8250_dw: Support clk framework also with ACPI
serial: 8250_dw: Enable runtime PM
...
This fixes the stub for dw8250_probe_acpi() that is used
when compiling without ACPI enabled. The argument type was
wrong.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 77e372a3d8.
Checking for disabled resources board breaks detection pnp on another
board "AMI UEFI implementation (Version: 0406 Release Date: 06/06/2012)".
I'm working with the reporter of the original bug to write and test
a better fix.
https://bugzilla.redhat.com/show_bug.cgi?id=928246
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider a situation where I have an ARM based system
and therefore no legacy ports. Say, I have two
memory-mapped ports. I use device tree to describe the
ports. What would be the config options I set so that
I get only the two ports in my system? I do not want
legacy ports being created automatically and I want
it to be flexible enough that it creates the devices
based only on the device tree. I expected setting
SERIAL_8250_RUNTIME_UARTS = 0 to work because the
description said, "Set this to the maximum number of
serial ports you want the kernel to register at boot
time." Unfortunately, even though SERIAL_8250_NR_UARTS
was set to the default value of 4, I did not get any device
nodes (because SERIAL_8250_RUNTIME_UARTS was 0). This
is what this change is addressing.
SERIAL_8250_NR_UARTS controls the maximum number of ports
you can support. SERIAL_8250_RUNTIME_UARTS specifies the
number of ports you want to create automatically for legacy
ports at boot time. All other ports will be created
when serial8250_register_port is called (and if does not exceed
the total number of supported ports as specified by
SERIAL_8250_NR_UARTS).
Signed-off-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Support for the WindRiver SBC8560 board was removed in v3.6. But there
are still a few lines depending on its obsolete Kconfig macro. Remove
these now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They were introduced by mistake in 3.7. Let's deprecate them now. For
the reasons, see the text in Kconfig below.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d1a
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9e4
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).
That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.
Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the tx_loadsz is the same as fifosize. This
will store the fifosize in it if it was not separately
delivered from the driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in 8250.c for detecting ARM/XScale UARTs says:
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
If the above passes, it then goes on to:
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable. According to the datasheet:
"LOWPOWER:When the bit is 1, close the internal benchmark
clock of serial port to set into low-power status.
So it essentially gets mis-detected as Xscale, and gets
powered down in the process. The device in question where
this was seen is listed by lspci as:
Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 835d844d1 (8250_pnp: do pnp probe before legacy probe), the
8250 driver was renamed to 8250_core. This means any existing usage of
the 8259.<xxxx> module parameters or as a kernel command line switch is
now broken, as the 8250_core driver doesn't parse options belonging to
something called "8250".
To solve this, we redefine the module options in a dummy function using
a redefined MODULE_PARAM_PREFX when built into the kernel. In the case
where we're building as a module, we provide an alias to the old 8250
name. The dummy function prevents compiler errors due to global variable
redefinitions that happen as part of the module_param_ macro expansions.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The InsydeH2O BIOS (version dated 09/12/2011) has the following in
its pnp resouces for its serial ports:
$ cat /sys/bus/pnp/devices/00:0b/resources
state = active
io disabled
irq disabled
We do not check if the resources are disabled, and create a bogus
ttyS* device. Since commit 835d844d1a (8250_pnp: do pnp probe
before legacy probe) we get a bogus ttyS0, which prevents the legacy
probe from detecting it.
Note, the BIOS can also be upgraded, fixing this problem, but for people
who can't do that, this fix is needed.
Reported-by: Vincent Deffontaines <vincent@gryzor.com>
Tested-by: Vincent Deffontaines <vincent@gryzor.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've managed to find an 8 port version of the card 4 port card which was discussed here:
http://marc.info/?l=linux-serial&m=120760744205314&w=2
Looking back at that thread there were two issues in the original patch.
1) The I/O ports for the UARTs are within BAR2 not BAR0. This can been seen in the original post.
2) A serial quirk isn't needed as these cards have no memory in BAR0 which makes pci_plx9050_init just return.
This patch fixes the 4 port support to use BAR2, removes the bogus quirk and adds support for the 8 port card.
$ lspci -vvv -n -s 00:08.0
00:08.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1588
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 1: I/O ports at ff00 [size=128]
Region 2: I/O ports at fe00 [size=64]
Region 3: I/O ports at fd00 [size=8]
Capabilities: <access denied>
Kernel driver in use: serial
$ dmesg | grep 0000:00:08.0:
[ 0.083320] pci 0000:00:08.0: [10b5:9050] type 0 class 0x000780
[ 0.083355] pci 0000:00:08.0: reg 14: [io 0xff00-0xff7f]
[ 0.083369] pci 0000:00:08.0: reg 18: [io 0xfe00-0xfe3f]
[ 0.083382] pci 0000:00:08.0: reg 1c: [io 0xfd00-0xfd07]
[ 0.083460] pci 0000:00:08.0: PME# supported from D0 D3hot
[ 1.212867] 0000:00:08.0: ttyS4 at I/O 0xfe00 (irq = 17) is a 16550A
[ 1.233073] 0000:00:08.0: ttyS5 at I/O 0xfe08 (irq = 17) is a 16550A
[ 1.253270] 0000:00:08.0: ttyS6 at I/O 0xfe10 (irq = 17) is a 16550A
[ 1.273468] 0000:00:08.0: ttyS7 at I/O 0xfe18 (irq = 17) is a 16550A
[ 1.293666] 0000:00:08.0: ttyS8 at I/O 0xfe20 (irq = 17) is a 16550A
[ 1.313863] 0000:00:08.0: ttyS9 at I/O 0xfe28 (irq = 17) is a 16550A
[ 1.334061] 0000:00:08.0: ttyS10 at I/O 0xfe30 (irq = 17) is a 16550A
[ 1.354258] 0000:00:08.0: ttyS11 at I/O 0xfe38 (irq = 17) is a 16550A
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Altera 8250/16550 compatible serial port.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS based Ralink WiSoC platform has 1 or more 8250 compatible serial cores.
To make them work we require the same quirks that are used by AU1x00.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for later SUNIX (TIMEDIA) Universal PCI Single and Multi-Port
Communications Boards.
These boards have PCI Vendor ID 1fd4 with device ID 1999 but otherwise
appear to be the same as the TIMEDIA boards already supported by 8250_pci
and parport_serial.
Tested with:
a. the two port serial board part number SER5037A,
b. the two port serial and one port parallel board part number
MIO5079A.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fields must be null-terminated, or next printk for %s, will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default burst is often 1 byte which is not very optimal.
The ideal burst size when using 16550A type port would be
1/2 of fifosize, but this does not work with all Designware
implementations. Setting it to 1/4 fifosize.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
