* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_via: Handle laptops via DMI
libata: -ENODEV during prereset isn't an error
libata: don't consider 0xff as port empty if SStatus is available
ata_piix: add short 40c quirk for Acer Aspire 2030, take #2
pata_sis: Fix and clean up some timing setups
hpt3x2n: Correct revision boundary
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] acpi_get_sysname() should be __init
[IA64] Cleanup acpi header to reuse the generic _PDC defines
[IA64] Fix using uninitialized data in _PDC setup
[IA64] start_secondary() and smp_callin() should be __cpuinit
Oh the joy of saving a fraction of a cent using short 40 wire cables and
not faking 80wire
Teach the VIA driver that there are some systems we need to know are
magically wired for high speeds.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Francis Russell <FrancisRussell@btinternet.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During prereset, -ENODEV return from ata_wait_ready() is not an error.
This causes unnecessary bug message on controllers which uses 0xff to
indicate empty port. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers (sata_sil) use 0xff to indicate port not ready
status, not port empty. As libata interprets 0xff as port empty, this
causes unnecessary reset failure and retry. Don't consider 0xff as
port empty if SStatus is available and indicates that port is online.
Signed-off-by: tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Indan Zupancic <indan@nul.nu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Steve H. <mail.pandor@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new
generation controllers in error.
- Use byte size operations where it is cleaner for mode setup
- Fix a couple of masking errors on certai chip revs when setting speeds
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a revision that isn't correctly claimed as two drivers both go
for it: Fix the test accordingly. Noticed originally by Bill Nottingham.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sys_setsockopt() do not check properly timeout values for
SO_RCVTIMEO/SO_SNDTIMEO, for example it's possible to set negative timeout
values. POSIX do not defines behaviour for sys_setsockopt in case negative
timeouts, but requires that setsockopt() shall fail with -EDOM if the send and
receive timeout values are too big to fit into the timeout fields in the socket
structure.
In current implementation negative timeout can lead to error messages like
"schedule_timeout: wrong timeout value".
Proposed patch:
- checks tv_usec and returns -EDOM if it is wrong
- do not allows to set negative timeout values (sets 0 instead) and outputs
ratelimited information message about such attempts.
Signed-off-By: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
They're the same.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing process of T.120 address in OpenLogicalChannelAck signal.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the implementation of H.323, it's not necessary to check
the addresses in Information signals.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update get_h225_addr() to meet the changes in ASN.1 types. It was using
field ip6 to access IPv6 TransportAddress, it should be ip according the
ASN.1 definition.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add support for decoding IPv6 address. I know it was manually added in
the header file, but not in the template file. That wouldn't work.
2. Add missing support for decoding T.120 address in OLCA.
3. Remove unnecessary decoding of Information signal.
Signed-off-by: Jing Min Zhao <zhaojingmin@vivecode.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet size is changed by the FTP NAT helper, the connection
tracking helper adjusts the sequence number of the newline character
by the size difference. This is wrong because NAT sequence number
adjustment happens after helpers are called, so the unadjusted number
is compared to the already adjusted one.
Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to locate the oldest entry in the history of newline character
sequence numbers, the sequence number of the current entry is incorrectly
compared with the index of the oldest sequence number instead of the number
itself.
Additionally it is not made sure that the current sequence number really
is after the oldest known one.
Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event cache time must be an absolute value, when no event exists
it is incorrectly set to 1s instead of 1s in the future.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you replace route via ip r r command the netlink multicast message is
not send. This patch corrects it. NL message is sent with NLM_F_REPLACE
flag.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8320
Signed-off-by: Milan Kocian <milon@wq.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mutex instead of binary semaphore in idt77252 driver.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch that changed the return value of qdisc_restart
incorrectly made the case where dequeue returns empty continue
processing packets.
This patch is based on diagnosis and fix by Patrick McHardy.
Reported-and-debugged-by: Anant Nitya <kernel@prachanda.info>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the cpu irq mask define to include the timer irq.
Another flag check was setting up the timer bit in all cases so we
didn't notice the issue.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The stats update code in spider_net_pass_skb_up() is touching the skb
after it's been passed up to the stack. To avoid that, just update the
stats first.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The meth ethernet driver for the SGI IP32 aka O2 is so far still an old
style driver which does not use the device driver model. This is now
causing issues with some udev based gadgetry in debian-stable. Fixed by
converting the meth driver to a platform device.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
--
Fixes since previous patch:
o Fixed typo in meth_exit_module()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch has removed unnecessary dependency on VIA velocity config.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the following compiler warning (and warnings resulting from
the correction):
warning: 'fixed_mdio_register_device' defined but not used
Signed-off-by: Denver Gingerich <denver@ossguy.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(Originally sent to linux-usb-devel)
The attached patch adds the device IDs for the Belkin F5D5055 device.
Reported by Andy Juniper <ajuniper@freeuk.com>
Signed-off-by: David Hollis <dhollis@davehollis.com>
--
David Hollis <dhollis@davehollis.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix MODULE_DEVICE_TABLE() duplication in ucc_geth.c and ucc_geth_mii.c
for ucc_geth to be compiled as module.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
time_after() was used backwards, so the timeout occurred immediately.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to initialize the owner bit of send queue WQEs to hardware
ownership whenever the QP is modified from reset to init, not just
when the QP is first allocated. This avoids having the hardware
process stale WQEs when the QP is moved to reset but not destroyed and
then modified to init again.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Section mismatch: reference to .init.text:acpi_find_rsdp
(between 'acpi_get_sysname' and 'acpi_request_vector')
acpi_get_sysname() needs to call the __init function acpi_find_rsdp, but it
doesn't have the __init attribute itself, hence the warning. Luckily it is
only called from machvec_init() which has __init attribute, so the fix
is to define acpi_get_sysname() as __init too.
Signed-off-by: Tony Luck <tony.luck@intel.com>
.. it got changed to 'i_mutex' some time ago.
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ia64 _PDC setup is defined similar to i386. So, cleanup the header to use
generic _PDC defines than using specific defines in ia64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
