The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of flush_schedule_work() made no sense and caused a syzkaller error.
Replace with the correct cancel_delayed_work_sync().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+69780d144754b8071f4b@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.20 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If you create multiple vivid instances, each with their own media
device, then there was no way to tell them apart.
Fill in the bus_info so each instance has a unique bus_info string.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The video_device structure is only copied into another structure, so
it can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The capture DV timings capabilities allowed for a minimum width and
height of 0. So passing a timings struct with 0 values is allowed
and will later cause a division by zero.
Ensure that the width and height must be >= 16 to avoid this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+57c3d83d71187054d56f@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
kthread_run returns an error pointer, but elsewhere in the code
dev->kthread_vid_cap/out is checked against NULL.
If kthread_run returns an error, then set the pointer to NULL.
I chose this method over changing all kthread_vid_cap/out tests
elsewhere since this is more robust.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+53d5b2df0d9744411e2e@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The fields of a v4l2_subdev_ops structure are all const, so the
structures that are stored there and are not used elsewhere can be
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_m2m_ops structure can be const as it is only passed to
v4l2_m2m_init whose parameter is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_ctrl_ops structure is only stored in the ops field of a
v4l2_ctrl_config structure, and this field is const, or passed as the
second argument of v4l2_ctrl_new_std, and the corresponding parameter
is declared as const. Accordingly, the structure can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do a series of minor corrections at the V4L2 uAPI documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I noticed that repeatedly running 'cec-ctl --playback' would occasionally
select 'Playback Device 2' instead of 'Playback Device 1', even though there
were no other Playback devices in the HDMI topology. This happened both with
'real' hardware and with the vivid CEC emulation, suggesting that this was an
issue in the core code that claims a logical address.
What 'cec-ctl --playback' does is to first clear all existing logical addresses,
and immediately after that configure the new desired device type.
The core code will poll the logical addresses trying to find a free address.
When found it will issue a few standard messages as per the CEC spec and return.
Those messages are queued up and will be transmitted asynchronously.
What happens is that if you run two 'cec-ctl --playback' commands in quick
succession, there is still a message of the first cec-ctl command being transmitted
when you reconfigure the adapter again in the second cec-ctl command.
When the logical addresses are cleared, then all information about outstanding
transmits inside the CEC core is also cleared, and the core is no longer aware
that there is still a transmit in flight.
When the hardware finishes the transmit it calls transmit_done and the CEC core
thinks it is actually in response of a POLL messages that is trying to find a
free logical address. The result of all this is that the core thinks that the
logical address for Playback Device 1 is in use, when it is really an earlier
transmit that ended.
The main transmit thread looks at adap->transmitting to check if a transmit
is in progress, but that is set to NULL when the adapter is unconfigured.
adap->transmitting represents the view of userspace, not that of the hardware.
So when unconfiguring the adapter the message is marked aborted from the point
of view of userspace, but seen from the PoV of the hardware it is still ongoing.
So introduce a new bool transmit_in_progress that represents the hardware state
and use that instead of adap->transmitting. Now the CEC core waits until the
hardware finishes the transmit before starting a new transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If debug_phys_addr is set, then CEC_CAP_PHYS_ADDR is added to the CEC
adapter capabilities.
This allows for testing CEC even if the physical address isn't set. This
makes it possible to connect two HDMI outputs together and still use CEC.
Very useful for testing CEC if you don't have access to an HDMI receiver
under linux.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC specification requires that the Vendor ID (if any) is reported
after a logical address was claimed.
This was never done, so add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a filehandle is dup()ped, then it is possible to close it from one fd
and call mmap from the other. This creates a race condition in vb2_mmap
where it is using queue data that __vb2_queue_free (called from close())
is in the process of releasing.
By moving up the mutex_lock(mmap_lock) in vb2_mmap this race is avoided
since __vb2_queue_free is called with the same mutex locked. So vb2_mmap
now reads consistent buffer data.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: syzbot+be93025dd45dccd8923c@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return 0 when invalidating the logical address. The cec core produces
a warning for drivers that do this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Torbjorn Jansson <torbjorn.jansson@mbox200.swipnet.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the tx_ignore_nack_until_eom error injection was activated,
then tx_nacked was never set instead of setting it when the last
byte of the message was transmitted.
As a result the transmit was marked as OK, when it should have
been NACKed.
Modify the condition so that it always sets tx_nacked when the
last byte of the message was transmitted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Documentation and code was linking the old documentation at:
http://v4l2spec.bytesex.org/spec/x1904.htm
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/staging/media/sunxi/cedrus/cedrus.c:421:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 50e761516f ("media: platform: Add Cedrus VPU decoder driver")
CC: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car CSI-2 interface has a number of selectable 'channels' that
provides pixel data to the VINs during image acquisition.
Each channel can be used to match a CSI-2 data type and a CSI-2 virtual
channel to be routed to output path.
Different SoCs have different number of channels, with R-Car E3 being the
notable exception supporting only 2 of them.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for R-Car E3 R8A77965 to R-Car CSI-2 driver.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add R-Car E3 R8A77990 SoC to the rcar-vin supported ones.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add compatible string for R-Car E3 R8A77990 to the list of SoCs supported by
rcar-vin driver.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Improve the pxp_soft_reset() error message by moving it to the
caller function, associating it with a proper device and also
by displaying the error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
pxp_soft_reset() may fail with a timeout, so it is better to propagate
the error in this case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In addition to the S_FMT debug output, S_SELECTION (SEL_TGT_CROP) is
relevant to determine encoded size. Add debug output for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Consistently add the context index to debug output, which otherwise is
impossible to make sense of when two contexts are running concurrently.
For this purpose, add a convenience macro coda_dbg(). Use the function
name with the coda_ prefix stripped as keyword where applicable, and
consistently use vid-out and vid-cap names for the queues. Add sequence
counters to the decoder job finished message and correctly indicate B
frames. Add a start streaming message to complement the stop streaming
message and a start encoding message to complement the existing start
decoding message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use v4l2_type_names to indicate which of the two queues is busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error code looks much more like a bit field than an error value.
Print it as hex rather than decimal.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance complains if G_PARM returns 0 in the denominator.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance complains about S_PARM being supported, but not
ENUM_FRAMEINTERVALS.
Report a continuous frame interval even though the hardware only
supports 16-bit numerator and denominator, with min/max values
that can be programmed into the mailbox registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The flag is already set in coda_g_parm, but v4l2-compliance complains
about it not being set during S_PARM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CODA driver uses threaded IRQs only, so there is nothing happening
in hardirq context that could interfere with the buffer meta handling.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The per-device instance list is unused, remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Three macroblocks seem to be the minimum resolution that can be encoded
and decoded by the CODA960 h.264 codec. Picture run commands fail for
smaller resolutions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ringbuffer used to hold the bitstream is very conservatively sized,
as keyframes can get very large and still need to fit into this buffer.
This means that the buffer is way oversized for the average stream to
the extend that it will hold a few hundred frames when the video data
is compressing well.
The current strategy of queueing as much bitstream data as possible
leads to large delays when draining the decoder. In order to keep the
drain latency to a reasonable bound, try to only queue a full reorder
window of buffers. We can't always hit this low target for very well
compressible video data, as we might end up with less than the minimum
amount of data that needs to be available to the bitstream prefetcher,
so we must take this into account and allow more buffers to be queued
in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream prefetch unit reads data in 256 byte blocks with some kind
of queueing. For the decoder to see data up to a desired position in the
next run, the bitstream has to be filled for 2 256 byte blocks past that
position aligned up to the next 256 byte boundary.
This should make sure we never run into a buffer underrun condition if
userspace does not supply new input buffers fast enough.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Storing the unmasked kfifo->in position as meta->start and ->end allows
to more easily compare a point past meta->end with the current
kfifo->in.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ffz() return value is undefined if the instance mask does not
contain any zeros. If it returned 32, the following set_bit would
corrupt the debugfs_root pointer.
Switch to IDA for context index allocation. This also removes the
artificial 32 instance limit for all except CodaDx6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Swapping the order between v4l2 subdevice registration and checking chip
id in b7a417628a ("media: ov2680: don't register the v4l2 subdevice
before checking chip ID") makes the mode restore to use the sensor
controls before they are set, so move the mode restore call to s_power
after the handler setup for controls is done.
This remove also the need for the error code path in power on function.
Fixes: b7a417628a ("media: ov2680: don't register the v4l2 subdevice before checking chip ID")
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document that changing the frame interval has no effect on frame size.
While this was the assumption in the API, it was not documented as such.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The first device that used that IP was the A31. Add it to our list of
compatibles.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The H3 has a slightly different CSI controller (no BT656, no CCI) which
looks a lot like the original A31 controller. Add a compatible for the A31,
and more specific compatible the for the H3 to be used in combination for
the A31.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are a few other coding style issues reported by checkpatch
while in --strict mode. Fix the ones that make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make checkpatch.pl happier by running it on strict mode and
using the --fix-inline to solve some issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allwinner V3s SoC features a CSI module with parallel interface.
This patch implement a v4l2 framework driver for it.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
