As noted in the headers for V4L2_SUBDEV_FL_HAS_EVENTS,
"controls can send events, thus drivers exposing controls
should set this flag".
This driver exposes controls, but didn't reflect that it
could generate events. Correct this, and add the default
event handler functions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports 8 or 10 bit readout modes, but the
driver only supported 10 bit.
Add 8 bit readout.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As required by libcamera, add the relevant cropping targets
to report which portion of the sensor is being read out in
any mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no reason why HBLANK has to be read-only as it
only changes the TIMING_HTS register in the sensor.
Remove the READ_ONLY flag, and add the relevant handling
for it.
The minimum value also varies based on whether continuous clock
mode is being used or not, so allow hblank_min to depend on
that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds support for V4L2_CID_HFLIP and V4L2_CID_VFLIP to allow
flipping the image.
The driver previously enabled H & V flips in the register table,
therefore the controls default to the same settings to avoid
changing the behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Programming the sensor with TIMING_VTS (aka LPFR) was done
when triggered by a change in exposure or gain, but not
when V4L2_CID_VBLANK was changed. Dynamic frame rate
changes could therefore not be achieved.
Separate out programming TIMING_VTS so that it is triggered
by set_ctrl(V4L2_CID_VBLANK)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use v4l2_ctrl_new_fwnode_properties to add V4L2_CID_CAMERA_ORIENTATION
and V4L2_CID_CAMERA_SENSOR_ROTATION.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports either having the CSI2 clock lane free
running, or gated when there is no packet to transmit.
The driver only selected gated (non-continuous) clock mode.
Add code to allow fwnode to configure whether the clock is
gated or free running.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The configured vblank_min setting of 151 (meaning VTS of
720 + 151 = 871) is far higher than the setting that works on
the sensor, and there are no obvious restrictions stated in the
datasheet.
Reduce the vblank_min to allow for faster frame rates.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The calculations from pixel rate, width+hblank, and height+vblank
do not give the correct framerate - it's half the speed it should
be.
The datasheet lists the default for the TIMING_HTS registers (0x380c/d)
as being 0x2d8 (728) which is less than the width of the image, so
the units clearly can't be pixels.
If TIMING_HTS is considered to be units of 2-pixels, then the
resulting value of 0x5b0 (1456) makes all the calculations correct.
This driver is reporting an HBLANK value of 250, with an image width
of 1280, so TIMING_HTS is 1530 (0x5fa) pixels. However it was also
setting the register to 0x5fa, thereby not taking into account it
being units of 2-pixels.
Correct the register value to 0x2fd so that all the timing calculations
give the correct results.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver currently has multiple assumptions that there is
only one supported mode.
Convert supported_mode to an array, and fix up all references
to correctly look at that array.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The pixel rate is determined by the PLL setup in the common
registers, not by the mode specific registers, therefore
remove it from the mode definition and define it for all modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The format code is independent of mode, and each mode could
support both Y10 and Y8, so disassociate the code from the
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently only one mode is supported, so all registers were
dropped in one list.
In preparation for adding more modes, split out the common registers
from those which configure the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
TIMING_VTS (registers 0x380e/f), EXPOSURE (registers
0x3500/1/2), and GAIN (0x3509) are all set from
ov9282_update_exp_gain as part of the control handler,
therefore they do not need to be in the main list of
registers.
Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make sure we call ov5645_entity_init_cfg() before registering the subdev
to make sure default formats are set up.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make sure we call the PM functions while s_stream(0) even in case of
errors in the code flow.
v4l2-core takes care of warning the user so no need to add a warning
message in the driver.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Switch to using runtime PM for power management.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Sony imx577 uses the same silicon enabling reference code in the
available examples provided as the imx412.
Add in compatible strings to enable and differentiate the parts.
Cc: sakari.ailus@iki.fi
Cc: dave.stevenson@raspberrypi.com
Cc: jacopo@jmondi.org
Cc: "Paul J. Murphy" <paul.j.murphy@intel.com>
Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
imx412 and imx577 return the same chip-id when interrogated via i2c.
I've confirmed this myself by
Sakari suggested we should add a new compat which should be reflected in
the name of the media entity
https://patchwork.kernel.org/project/linux-media/patch/20220607134057.2427663-3-bryan.odonoghue@linaro.org/#24894500
Set up the .data parameter of of_device_id to pass a string which
we use to set the media entity name. Once done we can add in imx577 as a
compatible chips with the media names reflecting the directed compat string.
Cc: sakari.ailus@iki.fi
Cc: dave.stevenson@raspberrypi.com
Cc: jacopo@jmondi.org
Cc: "Paul J. Murphy" <paul.j.murphy@intel.com>
Cc: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix minor nits from the last review round: extra {}, temporary
variables for ARRAYS_SIZE(), redundant check in ov4689_check_hwcfg.
No functional change intended.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Nothing in the kernel uses the platform data code path.
Drop it, and drop the use of the old legacy <linux/gpio.h>
API in the process.
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver includes the legacy <linux/gpio.h> header but does
not use any symbols from it. Drop the include.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver was including legacy headers despite using just
<linux/gpio/consumer.h>. Drop the surplus includes.
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Adding support for the TC358746 parallel <-> MIPI CSI bridge. This chip
supports two operating modes:
1st) parallel-in -> mipi-csi out
2nd) mipi-csi in -> parallel out
This patch only adds the support for the 1st mode.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: remove() now returns void]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Add support for low-power probe to the driver. Also fix runtime PM API
usage in the driver.
Much of the hassle comes from different factors affecting device power
states during probe for ACPI and DT.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 859891228e ("media: i2c: dw9768: Add DW9768 VCM driver")
The IMX290 gain register controls the analogue gain. Replace the
V4L2_CID_GAIN control with V4L2_CID_ANALOGUE_GAIN.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Implement read-only access to crop selection rectangles to expose the
analogue crop rectangle. The public (leaked) IMX290 documentation is not
very clear on how cropping is implemented and configured exactly, so
the margins may not be entirely accurate.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver duplicates the same pattern to access the try or active
format in multiple locations. Factor it out to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Registers 0x3012, 0x3013 and 0x3480 are not documented and are set in
the per-mode register arrays with values indentical for all modes. Move
them to the common array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Create the V4L2_CID_ORIENTATION and V4L2_CID_ROTATION controls to
expose the corresponding fwnode properties.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Add support for the V4L2_CID_HBLANK and V4L2_CID_VBLANK controls to the
imx290 driver. Make the controls read-only to start with, to report the
values to userspace for timing calculation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The imx290_probe() function is too large. Split control initialzation to
a dedicated function to increase code readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The gain is expressed in multiple of 0.3dB, as a value between 0.0dB
and 72.0dB. Gains between 0.0dB and 30.0dB (included) apply analog gain
only, higher gains from 30.3dB to 72dB apply additional digital gain.
The maximum gain value is erroneously set to 72. Increase it to 100 to
cover the whole analog gain range. Support for digital gain can be added
separately if needed.
The IMX327 and IMX462 are largely compatible with the IMX290, but have
an analog gain range of 0.0dB to 29.4dB and 42dB of digital gain. When
support for those sensors gets added to the driver, the gain control
should be adjusted accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Support configuring the exposure time, which is expressed as the
complement of the exposure time (frame period minus integration time).
The frame period is currently fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Define macros for all registers programmed by the driver for which
documentation is available to increase readability. This starts making
use of 16-bit registers in the register arrays, so the value field has
to be increased to 32 bits.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Error handling for register writes requires checking the error status of
every single write. This makes the code complex, or incorrect when the
checks are omitted. Simplify this by passing a pointer to an error code
to the imx290_write_reg() function, which allows writing multiple
registers in a row and only checking for errors at the end.
While at it, rename imx290_write_reg() to imx290_write() as there's
nothing else than registers to write, and rename imx290_read_reg()
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Define registers with the appropriate size, using the variable-size
register access mechanism that has just been introduced. This simplifies
the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The IMX290 has registers of different sizes. To simplify the code,
handle this in the read/write functions instead of in the callers by
encoding the register size in the symbolic name macros. All registers
are defined as 8-bit for now, a subsequent change will move to larger
registers where applicable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The HMAX value specifies the total line length in pixels. It's thus more
readable in decimal than hexadecimal. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Only two registers are ever read, and once only. There's no need to
cache values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The imx290_write_buffered_reg() function wraps a register write with
register hold, to enable changing multiple registers synchronously. It
is used for the gain only, which is an 8-bit register, defeating its
purpose.
The feature is useful, but should be implemented differently. Drop the
function for now, to prepare for a rework of register access.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Use ARRAY_SIZE(imx290->supplies) for code that needs the size of the
array, instead of relying on the IMX290_NUM_SUPPLIES. The result is less
error-prone as it ties the size to the array.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Knowing why I2C transfers fail is useful for debugging. Extend the error
message to print the error code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The link frequency and pixel rate controls are set without holding the
control handler lock, resulting in kernel warnings. As the value of
those controls depend on the format, the simplest fix is to use the
device lock for the control handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The VGXY61 has a quad lanes CSI-2 output port running at 800mbps per
lane, and supports RAW8, RAW10, RAW12, RAW14 and RAW16 formats.
The driver handles both sensor types:
- VG5661 and VG6661: 1.6 Mpx (1464 x 1104) 75fps.
- VG5761 and VG6761: 2.3 Mpx (1944 x 1204) 60 fps.
The driver supports:
- HDR linearize mode, HDR substraction mode, and no HDR
- GPIOs LEDs strobing
- Digital binning and analog subsampling
- Horizontal and vertical flip
- Manual exposure
- Analog and digital gains
- Test patterns
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
[Sakari Ailus: remove() now returns void]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Add a V4L2 sub-device driver for OmniVision OV4689 image sensor. This
is a 4 Mpx image sensor using the I2C bus for control and the CSI-2
bus for data.
This driver supports following features:
- manual exposure and analog gain control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2688x1520 at 30 fps
The driver provides all mandatory V4L2 controls for compatibility with
libcamera. The sensor supports 1/2/4-lane CSI-2 modes, but the driver
implements 4 lane mode only at this moment.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
