Convert driver so that it uses regmap instead of directly using
spi_transfer for all register accesses.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace spaces with tab, so that the tsc2005 Kconfig entry matches the
other entries in drivers/input/touchscreen/Kconfig.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve defines for first control byte by removing 0x00 prefix (the defines
are for 8 bit values and not for 16 bit values) and expose register
structure by exposing the shift.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
Commit 2d53809594 ("Input: zforce_ts - convert to use the gpiod
interface") converted this driver to use the gpiod functions. These
functions take the active low property into account, so we don't have
to invert the result of gpiod_get_value_cansleep(). This has been
missed in that commit. Fix it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The original wait time was 200ms which was enough for the firmware to
finish loading and boot. After that the firmware will perform
initialization and touch calibration, which will take about 1.1 second. The
touch calibration will change controller frequency to scan at the most
optimal frequency and during calibration/frequency switching process we may
run into i2c data errors. To avoid them we extend the sleep to 2500ms after
issuing the sw reset.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes can be used to identify controllers present in the system.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch form OF to device properties so that common parsing code could
work not only on device tree but also on ACPI-based platforms.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The binding specification says that "touchscreen-size-x" and "-y" specify
horizontal and vertical resolution of the touchscreen and therefore maximum
absolute coordinates should be reduced by 1 since we are starting with 0.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do issue warning about axis that is present in device tree but not specified
by the driver even in case of multi-touch axis as callers now tell us if they
expect multi-touch data or not.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new GPIO descriptor interface to handle the zForce GPIOs.
This simplifies the code and allows transparently handle GPIO polarity, as
specified in device tree data.
Also switch to using gpio_{set|get}_value_cansleep() since none of the
callers is in atomic context and cansleep variant allows more GPIO
controllers to be used with the touchscreen.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull second round of input updates from Dmitry Torokhov:
"A new driver for Weida wdt87xx touch controllers, and a bunch of
fixups for other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wdt87xx_i2c - add a scaling factor for TOUCH_MAJOR event
Input: wdt87xx_i2c - remove stray newline in diagnostic message
Input: arc_ps2 - add HAS_IOMEM dependency
Input: wdt87xx_i2c - fix format warning
Input: improve parsing OF parameters for touchscreens
Input: edt-ft5x06 - mark as direct input device
Input: use for_each_set_bit() where appropriate
Input: add a driver for wdt87xx touchscreen controller
Input: axp20x-pek - fix reporting button state as inverted
Input: xpad - re-send LED command on present event
Input: xpad - set the LEDs properly on XBox Wireless controllers
Input: imx_keypad - check for clk_prepare_enable() error
Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning:
drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
size, fw->size);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJ/U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvements at the DVB API DocBook documentation. Now, the
frontend and the network APIs are fully in sync with the Kernel and
looks more like the rest of the media documentation;
- New frontend driver: cx24120
- New driver for a PCI device: cobalt. This driver is actually not
sold in the market, but it is a good example of a multi-HDMI input
device;
- The dt3155 driver were promoted from staging;
- The mantis driver got remote controller support;
- New V4L2 driver for ST bdisp SoC chipsets;
- Make sparse and smatch happier: several bugs were solved by fixing
the issues reported by those static code analyzers.
- Lots of new device additions, new features, improvements and cleanups
at the existing drivers.
* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
[media] lmedm04: fix the range for relative measurements
[media] lmedm04: use u32 instead of u64 for relative stats
[media] omap3isp: remove unused var
[media] saa7134: fix page size on some archs
[media] use CONFIG_PM_SLEEP for suspend/resume
[media] tuner-i2c: be consistent with I2C declaration
[media] si470x: cleanup define namespace
[media] bdisp: prevent compiling on random arch
[media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
[media] MAINTAINERS: Add entry for the Renesas VSP1 driver
[media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
[media] Revert "[media] vb2: Push mmap_sem down to memops"
[media] mantis: cleanup a warning
[media] bdisp-debug: don't try to divide by s64
[media] cx88: don't declare restart_video_queue if not used
[media] au0828: move dev->boards atribuition to happen earlier
[media] lmedm04: implement dvb v5 statistics
[media] bdisp: remove unused var
[media] bdisp: remove needless check
ts2020: fix compilation on i386
...
When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
This is a driver for Weida HiTech WDT87xx series touchscreen controller.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e21 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
Cc: stable@vger.kernel.org
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will do that for us.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix touchscreens export through their registers a Product ID and
Firmware Version. The Product ID is an ASCII encoding of the product name
(e.g.: "911").
Export to sysfs (through the input subsystem) the product id and firmware
version read from the device rather than using constant values.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix sparse warning:
drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used.
Replace the variable length array with fixed length.
Some Goodix devices have maximum 5 touch points, while others have 10 touch
points. Using the maximum length (80 bytes) for all devices will lead to
wasting 40 bytes on stack when using devices with maximum 5 touch points.
However, that is preferable to using kmalloc which will use even more
resources.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When stop_streaming is called while a frame is currently being retrieved, the
buffer being filled will still be returned with BUF_STATE_DONE. By resetting
the sequence number and checking before returning the buffer, it can now
correctly be returned with BUF_STATE_ERROR.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add dev_dbg statements for easier future debugging; also change the warning
about packet ID mismatches to debug output to avoid flooding the logs. This
warning is only important in a very specific/rare use case when trying to
correlate input events with video data.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add missing functions to query the single fixed frame size (960x540) and
supported frame rates. Technically, the SUR40 supports any arbitrary frame
rate up to 60 FPS, as it is polled and not interrupt-driven. For now, we
just report 30 and 60 FPS, which is sufficient to make most V4L2 tools work.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SUR40 hardware can deliver images at up to 60 FPS; at full USB2 bandwidth,
one raw frame will take about 11 ms to transmit. If the poll interval is above
5 ms, fully handling one frame will take longer than 16 ms and the overall
frame rate will drop below 60 FPS. To get the full frame rate without blocking
all the time and still allowing for a bit of timing jitter, we reduce the poll
interval to 4 ms.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The STMPE MFD is only used with device tree configured systems (and STMPE
MFD core depends on OF), so force the configuration to come from device
tree only.
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When STMPE is instantiated via device tree individual MFD cells rae formed
with OF modaliases, not platform modaliases, and so we need to add OF
device table to the driver if we want it to load automatically:
of:Nstmpe_touchscreenT<NULL>Cst,stmpe-ts
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the intent a tad more clear.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been testing wrong variable when trying to make sure that input
allocation succeeded.
Reported by Coverity (CID 1295918).
Acked-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
