When we allocate a new channel context, or find an existing one
that is compatible, we currently assign it to a link before its
mindef is updated. This leads to strange situations, especially
in link switching where you switch to an 80 MHz link and expect
it to be active immediately, but the mindef is still configured
to 20 MHz while assigning. Also, it's strange that the chandef
passed to the assign method's argument is wider than the one in
the context.
Fix this by calculating the mindef with the new link considered
before calling the driver.
In particular, this fixes an iwlwifi problem during link switch
where the firmware would assert because the (link) station that
was added for the AP is configured to transmit at a bandwidth
that's wider than the channel context that it's configured on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-5-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a chanctx is reserved for a new vif and we recalculate
the minimal definition for it, we need to consider the new
interface it's being reserved for before we assign it, so it
can be used directly with the correct min channel width.
Fix the code to - optionally - consider that, and use that
option just before doing the reassignment.
Also, when considering channel context reservations, we
should only consider the one link we're currently working with.
Change the boolean argument to a link pointer to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-4-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to call ieee80211_recalc_chanctx_min_def()
since it cannot and won't call the driver anyway; just use
_ieee80211_recalc_chanctx_min_def() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-3-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When stopping the AP, there might be a color change in progress. It
should be deactivated here, or the driver might later finalize a color
change on a stopped AP.
Fixes: 5f9404abdf (mac80211: add support for BSS color change)
Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230504080441.22958-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to set the correct trace variable, otherwise we're
overwriting something else instead and the right one that
we print later is not initialized.
Fixes: b6011960f3 ("mac80211: handle channel frequency offset")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-2-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature depends on a platform bugfix. Until we have a
mechanism that can verify a platform has the required bugfix,
disable RFI.
Fixes: ef3ed33dfc ("wifi: iwlwifi: bump FW API to 77 for AX devices")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Link: https://lore.kernel.org/linux-wireless/CAAJw_ZvZdFpw9W2Hisc9c2BAFbYAnQuaFFaFG6N7qPUP2fOL_w@mail.gmail.com/
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'changed' can be OR'ed with BSS_CHANGED_EHT_PUNCTURING which is larger than
an u32.
So, turn 'changed' into an u64 and update ieee80211_set_after_csa_beacon()
accordingly.
In the commit in Fixes, only ieee80211_start_ap() was updated.
Fixes: 2cc25e4b2a ("wifi: mac80211: configure puncturing bitmap")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/e84a3f80fe536787f7a2c7180507efc36cd14f95.1682358088.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.
Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);
The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING
While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING
When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.
Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.
Fixes: 7598f4b40b ("iavf: Move netdev_update_features() into watchdog task")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the current implementation that causes ice_trigger_vf_reset()
to start resetting the VF even when the VF-NIC is still initializing.
When we reset NIC with ice driver it can interfere with
iavf-vf initialization e.g. during consecutive resets induced by ice
iavf ice
| |
|<-----------------|
| ice resets vf
iavf |
reset |
start |
|<-----------------|
| ice resets vf
| causing iavf
| initialization
| error
| |
iavf
reset
end
This leads to a series of -53 errors
(failed to init adminq) from the IAVF.
Change the state of the vf_state field to be not active when the IAVF
is still initializing. Make sure to wait until receiving the message on
the message box to ensure that the vf is ready and initializded.
In simple terms we use the ACTIVE flag to make sure that the ice
driver knows if the iavf is ready for another reset
iavf ice
| |
| |
|<------------- ice resets vf
iavf vf_state != ACTIVE
reset |
start |
| |
| |
iavf |
reset-------> vf_state == ACTIVE
end ice resets vf
| |
| |
Fixes: c54d209c78 ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a core PF reset, the VFs were showing wrong Rx/Tx stats. This is a
regression in commit 6624e780a5 ("ice: split ice_vsi_setup into smaller
functions") caused by missing to set "stat_offsets_loaded = false" in the
ice_vsi_rebuild() path.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently driver can only allocate interrupt vectors during init phase by
calling pci_alloc_irq_vectors. Change that and make use of new
pci_msix_alloc_irq_at/pci_msix_free_irq API and enable to allocate and free
more interrupts after MSIX has been enabled. Since not all platforms
supports dynamic allocation, check it with pci_msix_can_alloc_dyn.
Extend the tracker to keep track how many interrupts are allocated
initially so when all such vectors are already used, additional interrupts
are automatically allocated dynamically. Remember each interrupt allocation
method to then free appropriately. Since some features may require
interrupts allocated dynamically add appropriate VSI flag and take it into
account when allocating new interrupt.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace custom interrupt tracker with generic xarray data structure.
Remove all code responsible for searching for a new entry with xa_alloc,
which always tries to allocate at the lowes possible index. As a result
driver is always using a contiguous region of the MSIX vector table.
New tracker keeps ice_irq_entry entries in xarray as opaque for the rest
of the driver hiding the entry details from the caller.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently interrupt allocations, depending on a feature are distributed
in batches. Also, after allocation there is a series of operations that
distributes per irq settings through that batch of interrupts.
Although driver does not yet support dynamic interrupt allocation, keep
allocated interrupts in a pool and add allocation abstraction logic to
make code more flexible. Keep per interrupt information in the
ice_q_vector structure, which yields ice_vsi::base_vector redundant.
Also, as a result there are a few functions that can be removed.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove redundant code from ice_get_max_valid_res_idx that has no effect.
ice_pf::irq_tracker is initialized during driver probe, there is no reason
to check it again. Also it is not possible for pf::sriov_base_vector to be
lower than the tracker length, remove WARN_ON that will never happen.
Get rid of ice_get_max_valid_res_idx helper function completely since it
can never return negative value.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All VF control VSIs share the same interrupt vector. Currently, a helper
function dedicated for that directly sets ice_vsi::base_vector.
Use helper that returns pointer to first found VF control VSI instead.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move away from using pci_enable_msix_range/pci_disable_msix and use
pci_alloc_irq_vectors/pci_free_irq_vectors instead.
As a result stop tracking msix_entries since with newer API entries are
handled by MSIX core. However, due to current design of communication
with RDMA driver which accesses ice_pf::msix_entries directly, keep
using the array just for RDMA driver use.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, driver gets interrupt number directly from ice_pf::msix_entries
array. Use helper function dedicated to do just that.
While at it use a variable to store interrupt number in
ice_free_irq_msix_misc instead of calling the helper function twice.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keep interrupt handling code in a dedicated file. This helps keep driver
structured better and prepares for more functionality added to this file.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Bagas Sanjaya says:
====================
SPDX conversion for bonding, 8390, and i825xx drivers
This series is SPDX conversion for bonding, 8390, and i825xx driver
subsystems. It is splitted from v2 of my SPDX conversion series in
response to Didi's GPL full name fixes [1] to make it easily
digestible.
The conversion in this series is divided by each subsystem and by
license type.
[1]: https://lore.kernel.org/linux-spdx/20230512100620.36807-1-bagasdotme@gmail.com/
====================
Link: https://lore.kernel.org/r/20230515060714.621952-1-bagasdotme@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The boilerplate reads that sun3_8256 driver is an extension to Linux
kernel core, hence add SPDX license identifier for GPL 2.0.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michael Hipp <hippm@informatik.uni-tuebingen.de>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace unversioned GPL boilerplate notice with corresponding SPDX
license identifier, which is GPL 1.0+.
Cc: Donald Becker <becker@scyld.com>
Cc: Richard Hirst <richard@sleepie.demon.co.uk>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The boilerplate refers to COPYING in the top-level directory of kernel
tree. Replace it with corresponding SPDX license identifier.
Cc: Donald Becker <becker@scyld.com>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Topi Kanerva <topi@susanna.oulu.fi>
Cc: Alain Malek <Alain.Malek@cryogen.com>
Cc: Bruce Abbott <bhabbott@inhb.co.nz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Fontana <rfontana@redhat.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace boilerplate notice for unversioned GPL to SPDX tag for GPL 1.0+.
For ne2k-pci.c, only add SPDX tag and keep the boilerplate instead,
since the boilerplate notes that it must be preserved.
Cc: David A. Hinds <dahinds@users.sourceforge.net>
Cc: Donald Becker <becker@scyld.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Fontana <rfontana@redhat.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Previous batches of SPDX conversion missed bond_main.c and bonding_priv.h
because these files doesn't mention intended GPL version. Add SPDX identifier
to these files, assuming GPL 1.0+.
Cc: Thomas Davis <tadavis@lbl.gov>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
__skb_fill_page_desc_noacc() is not doing any pfmemalloc
propagating, and yet it has a comment about that, commit
84ce071e38 ("net: introduce __skb_fill_page_desc_noacc")
may have accidentally moved it to __skb_fill_page_desc_noacc(),
so move it back to __skb_fill_page_desc() which is supposed
to be doing pfmemalloc propagating.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20230515050107.46397-1-linyunsheng@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: c96e731c93 ("net: bcmgenet: connect and disconnect from the PHY state machine")
Fixes: 93e0401e0f ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The P360 Tiny suffers from an irq storm issue like the T490s, so add
an entry for it to tpm_tis_dmi_table, and force polling. There also
previously was a report from the previous attempt to enable interrupts
that involved a ThinkPad L490. So an entry is added for it as well.
Cc: stable@vger.kernel.org
Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny
Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in
tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero
bytes. This prevents hwrng from racing during resume.
Cc: stable@vger.kernel.org
Fixes: 6e592a065d ("tpm: Move Linux RNG connection to hwrng")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Before sending a TPM command, CLKRUN protocol must be disabled. This is not
done in the case of tpm1_do_selftest() call site inside tpm_tis_resume().
Address this by decorating the calls with tpm_chip_{start,stop}, which
should be always used to arm and disarm the TPM chip for transmission.
Finally, move the call to the main TPM driver callback as the last step
because it should arm the chip by itself, if it needs that type of
functionality.
Cc: stable@vger.kernel.org
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Closes: https://lore.kernel.org/linux-integrity/CS68AWILHXS4.3M36M1EKZLUMS@suppilovahvero/
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
If it fails to attach fentry, the allocated bpf trampoline image will be
left in the system. That can be verified by checking /proc/kallsyms.
This meamleak can be verified by a simple bpf program as follows:
SEC("fentry/trap_init")
int fentry_run()
{
return 0;
}
It will fail to attach trap_init because this function is freed after
kernel init, and then we can find the trampoline image is left in the
system by checking /proc/kallsyms.
$ tail /proc/kallsyms
ffffffffc0613000 t bpf_trampoline_6442453466_1 [bpf]
ffffffffc06c3000 t bpf_trampoline_6442453466_1 [bpf]
$ bpftool btf dump file /sys/kernel/btf/vmlinux | grep "FUNC 'trap_init'"
[2522] FUNC 'trap_init' type_id=119 linkage=static
$ echo $((6442453466 & 0x7fffffff))
2522
Note that there are two left bpf trampoline images, that is because the
libbpf will fallback to raw tracepoint if -EINVAL is returned.
Fixes: e21aa34178 ("bpf: Fix fexit trampoline.")
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <song@kernel.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Link: https://lore.kernel.org/bpf/20230515130849.57502-2-laoar.shao@gmail.com
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> says:
this series converts the drivers below drivers/net/can to the
.remove_new() callback of struct platform_driver(). The motivation is to
make the remove callback less prone for errors and wrong assumptions.
See commit 5c5a7680e6 ("platform: Provide a remove callback that
returns no value") for a more detailed rationale.
All drivers already returned zero unconditionally in their
.remove() callback, so converting them to .remove_new() is trivial.
Link: https://lore.kernel.org/r/20230512212725.143824-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230512212725.143824-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230512212725.143824-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/r/20230512212725.143824-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
./drivers/net/can/bxcan.c:970:2-9: line 970 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:964:2-9: line 964 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:958:2-9: line 958 is redundant because platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4878
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230506080725.68401-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
