Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper function allows family implementations to access
their family's attrbuf. This gets rid of the attrbuf usage
in families, and also adds locking validation, since it's not
valid to use the attrbuf with parallel_ops or outside of the
dumpit callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user may want to use only some bits of the skb mark in
his skbedit rules because the remaining part might be used by
something else.
Introduce the "mask" parameter to the skbedit actor in order
to implement such functionality.
When the mask is specified, only those bits selected by the
latter are altered really changed by the actor, while the
rest is left untouched.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SGMII mode, we observed an autonegotiation issue
after power-down-up cycles where the copper side
reports successful link establishment but the
SGMII side's link is down.
This happened in a setup where the at8031 is
connected over SGMII to a eTSEC (fsl gianfar),
but so far could not be reproduced with other
Ethernet device / driver combinations.
This commit adds a wrapper function for at8031
that in case of operating in SGMII mode double
checks SGMII link state when generic aneg_done()
succeeds. It prints a warning on failure but
intentionally does not try to recover from this
state. As a result, if you ever see a warning
'803x_aneg_done: SGMII link is not ok' you will
end up having an Ethernet link up but won't get
any data through. This should not happen, if it
does, please contact the module maintainer.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 98267311fe.
Suspending the SGMII alongside the copper side
made the at803x inaccessable while powered down,
e.g. it can't be re-probed after suspend.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use d_fsdata instead of d_time
Miklos Szeredi <mszeredi@redhat.com>
use file_inode(file) instead of file->f_path.dentry->d_inode
Amir Goldstein <amir73il@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=b9Ly
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-rc2-ofs-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull oreangefs updates from Mike Marshall:
"A couple of orangefs cleanups sent in by other developers:
- use d_fsdata instead of d_time (Miklos Szeredi)
- use file_inode(file) instead of file->f_path.dentry->d_inode (Amir
Goldstein)"
* tag 'for-linus-4.9-rc2-ofs-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: don't use d_time
orangefs: user file_inode() where it is due
Changes in this update:
o iomap page offset masking fix for page faults
o add IOMAP_REPORT to distinguish between read and fiemap map requests
o cleanups to new shared data extent code
o fix mount active status on failed log recovery
o fix broken dquots in a buffer calculation
o fix locking order issues and merge xfs_reflink_remap_range and
xfs_file_share_range
o rework unmapping of CoW extents and remove now unused functions
o clean state when CoW is done.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LDDu
-----END PGP SIGNATURE-----
Merge tag 'xfs-fixes-for-linus-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update contains fixes for most of the outstanding regressions
introduced with the 4.9-rc1 XFS merge. There is also a fix for an
iomap bug, too.
This is a quite a bit larger than I'd prefer for a -rc3, but most of
the change comes from cleaning up the new reflink copy on write code;
it's much simpler and easier to understand now. These changes fixed
several bugs in the new code, and it wasn't clear that there was an
easier/simpler way to fix them. The rest of the fixes are the usual
size you'd expect at this stage.
I've left the commits to soak in linux-next for a some extra time
because of the size before asking you to pull, no new problems with
them have been reported so I think it's all OK.
Summary:
- iomap page offset masking fix for page faults
- add IOMAP_REPORT to distinguish between read and fiemap map
requests
- cleanups to new shared data extent code
- fix mount active status on failed log recovery
- fix broken dquots in a buffer calculation
- fix locking order issues and merge xfs_reflink_remap_range and
xfs_file_share_range
- rework unmapping of CoW extents and remove now unused functions
- clean state when CoW is done"
* tag 'xfs-fixes-for-linus-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (25 commits)
xfs: clear cowblocks tag when cow fork is emptied
xfs: fix up inode cowblocks tracking tracepoints
fs: Do to trim high file position bits in iomap_page_mkwrite_actor
xfs: remove xfs_bunmapi_cow
xfs: optimize xfs_reflink_end_cow
xfs: optimize xfs_reflink_cancel_cow_blocks
xfs: refactor xfs_bunmapi_cow
xfs: optimize writes to reflink files
xfs: don't bother looking at the refcount tree for reads
xfs: handle "raw" delayed extents xfs_reflink_trim_around_shared
xfs: add xfs_trim_extent
iomap: add IOMAP_REPORT
xfs: merge xfs_reflink_remap_range and xfs_file_share_range
xfs: remove xfs_file_wait_for_io
xfs: move inode locking from xfs_reflink_remap_range to xfs_file_share_range
xfs: fix the same_inode check in xfs_file_share_range
xfs: remove the same fs check from xfs_file_share_range
libxfs: v3 inodes are only valid on crc-enabled filesystems
libxfs: clean up _calc_dquots_per_chunk
xfs: unset MS_ACTIVE if mount fails
...
btrfs_remove_all_log_ctxs takes a shortcut where it avoids walking the
list because it knows all of the waiters are patiently waiting for the
commit to finish.
But, there's a small race where btrfs_sync_log can remove itself from
the list if it finds a log commit is already done. Also, it uses
list_del_init() to remove itself from the list, but there's no way to
know if btrfs_remove_all_log_ctxs has already run, so we don't know for
sure if it is safe to call list_del_init().
This gets rid of all the shortcuts for btrfs_remove_all_log_ctxs(), and
just calls it with the proper locking.
This is part two of the corruption fixed by cbd60aa7cd. I should have
done this in the first place, but convinced myself the optimizations were
safe. A 12 hour run of dbench 2048 will eventually trigger a list debug
WARN_ON for the list_del_init() in btrfs_sync_log().
Fixes: d1433debe7
Reported-by: Dave Jones <davej@codemonkey.org.uk>
cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Chris Mason <clm@fb.com>
Two small fixes: one is a fatal section mismatch (reference to init after it's
discarded) and the other two are iscsi locking fixes.
Signed-off-by: James E. J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BI5E
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one is a fatal section mismatch (reference to init
after it's discarded) and the other two are iscsi locking fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: NCR5380: no longer mark irq probing as __init
scsi: be2iscsi: Replace _bh with _irqsave/irqrestore
scsi: libiscsi: Fix locking in __iscsi_conn_send_pdu
Pull libata fixes from Tejun Heo:
"The AHCI MSI handling change in rc1 was a bit broken and caused disk
probing failures on some machines. These three patches should fix the
issues"
David Howells comments:
"My test machine fell foul of this using a PCIe M.2-attached SSD card.
The patches fix it for me"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix the single MSI-X case in ahci_init_one
ahci: fix nvec check
ahci: only try to use multi-MSI mode if there is more than 1 port
Pull block fixes from Jens Axboe:
"A set of fixes for this series, most notably the fix for the blk-mq
software queue regression in from this merge window.
Apart from that, a fix for an unlikely hang if a queue is flooded with
FUA requests from Ming, and a few small fixes for nbd and badblocks.
Lastly, a rename update for the proc softirq output, since the block
polling code was made generic"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: update hardware and software queues for sleeping alloc
block: flush: fix IO hang in case of flood fua req
nbd: fix incorrect unlock of nbd->sock_lock in sock_shutdown
badblocks: badblocks_set/clear update unacked_exist
softirq: Display IRQ_POLL for irq-poll statistics
The per-zone waitqueues exist because of a scalability issue with the
page waitqueues on some NUMA machines, but it turns out that they hurt
normal loads, and now with the vmalloced stacks they also end up
breaking gfs2 that uses a bit_wait on a stack object:
wait_on_bit(&gh->gh_iflags, HIF_WAIT, TASK_UNINTERRUPTIBLE)
where 'gh' can be a reference to the local variable 'mount_gh' on the
stack of fill_super().
The reason the per-zone hash table breaks for this case is that there is
no "zone" for virtual allocations, and trying to look up the physical
page to get at it will fail (with a BUG_ON()).
It turns out that I actually complained to the mm people about the
per-zone hash table for another reason just a month ago: the zone lookup
also hurts the regular use of "unlock_page()" a lot, because the zone
lookup ends up forcing several unnecessary cache misses and generates
horrible code.
As part of that earlier discussion, we had a much better solution for
the NUMA scalability issue - by just making the page lock have a
separate contention bit, the waitqueue doesn't even have to be looked at
for the normal case.
Peter Zijlstra already has a patch for that, but let's see if anybody
even notices. In the meantime, let's fix the actual gfs2 breakage by
simplifying the bitlock waitqueues and removing the per-zone issue.
Reported-by: Andreas Gruenbacher <agruenba@redhat.com>
Tested-by: Bob Peterson <rpeterso@redhat.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we end up sleeping due to running out of requests, we should
update the hardware and software queues in the map ctx structure.
Otherwise we could end up having rq->mq_ctx point to the pre-sleep
context, and risk corrupting ctx->rq_list since we'll be
grabbing the wrong lock when inserting the request.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Chris Mason <clm@fb.com>
Fixes: 63581af3f3 ("blk-mq: remove non-blocking pass in blk_mq_map_request")
Signed-off-by: Jens Axboe <axboe@fb.com>
The current state of driver removal is not great.
CONFIG_DEBUG_TEST_DRIVER_REMOVE finds lots of errors. The help text
currently undersells exactly how many errors this option will find. Add
a bit more description to indicate this option shouldn't be turned on
unless you actually want to debug driver removal. The text can be
changed later when more drivers are fixed up.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you edit a kernfs backed file with vi(1), you see an ugly error
message when you write the file because vi tries to fsync(2) the
file after writing, which fails.
We have noop_fsync() for this, use it.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resizing a vt its selection may exceed the new size, resulting in
an invalid memory access [1]. Clear the selection before resizing.
[1] http://lkml.kernel.org/r/CACT4Y+acDTwy4umEvf5ROBGiRJNrxHN4Cn5szCXE5Jw-d1B=Xw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_update first reads the IOState register and then triggers
a write if needed. However, GPIOS might be configured as an input so
the read to IOState on this GPIO is the current state which might
be random.
Signed-off-by: Francois Berder <Francois.Berder@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas RZ/G SoC also have the SCIF, SCIFA, SCIFB, and HSCIF ports and
they seem compatible with the R-Car gen2 SoC in this respect...
Document RZ/G1[ME] (also known as R8A774[35]) SoC bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NXP SC16C2552 requires that we always write a reset to the RX FIFO and
TX FIFO whenever we enable the FIFOs
Cc: xe-kernel@external.cisco.com
Signed-off-by: Steve Shih <sshih@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Size of kmalloc() in vc_do_resize() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Put a reasonable upper bound on terminal size to prevent WARNINGs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
CC: David Rientjes <rientjes@google.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where head == 0 on the circular buffer, there should be one
DMA buffer, not two. The second zero-length buffer would break the
lpuart driver, transfer would never complete.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4fe0d15488 ("PCI: Use positive flags in pci_alloc_irq_vectors()")
replaces flags from negative to positive values which makes mandatory to have
the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op).
This basically drops MSI enabling in 8250_lpss driver.
Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of
0 to pci_alloc_irq_vectors().
Fixes: 60a9244a5d ("serial: 8250_lpss: enable MSI for Intel Quark")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEs "output" can sometimes combine IEs coming from userspace
with IEs generated in the kernel - in particular mac80211 does
this for association frames.
Add support in this code for the 802.11 IE fragmentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the previous commits, initial FILS authentication/association
support is now functional in mac80211-based drivers for station role
(and FILS AP case is covered by user space in hostapd withotu requiring
mac80211 changes).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for encrypting (Re)Association Request frame and
decryption (Re)Association Response frame when using FILS in station
mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new nl80211 attributes can be used to provide KEK and nonces to
allow the driver to encrypt and decrypt FILS (Re)Association
Request/Response frames in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This defines authentication algorithms for FILS (IEEE 802.11ai).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the Element IDs and Element ID Extensions from IEEE
P802.11ai/D11.0. In addition, add a new cfg80211_find_ext_ie() wrapper
to make it easier to find information elements that used the Element ID
Extension field.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This defines a feature flag that drivers can use to indicate that they
support FILS authentication/association (IEEE 802.11ai) when using user
space SME (NL80211_CMD_AUTHENTICATE) in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The special SAE case should be limited only for SAE since the more
generic AUTH_DATA can now be used with other authentication algorithms
as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we split the wiphy dump because it got too large, I added a
comment and asked that all new command advertising be done only
for userspace clients capable of receiving split data, in order
to not break older ones (which can't use the new commands anyway)
This mostly worked, and we haven't added many new commands, but
I occasionally get patches that modify the wrong place.
Make this easier to detect and understand by splitting out the
old commands to a separate function that makes it more clear it
should never be modified again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 761ed4a945 ('tty: serial_core: convert uart_close to use
tty_port_close') started setting the ttyport console flag for serial
drivers. This is causing crashes, hangs, or garbage output on several
platforms because the serial shutdown is skipped and IRQs are left
enabled.
Partially revert commit 761ed4a945 and drop reporting UART tty_ports
as a console leaving the console handling to the serial_core as it was
before.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reported-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, 'value' is always a byte, then this code is clearing
bit 15, which is already clear. I meant to clear bit 7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `stm32_serial_remove':
stm32-usart.c:(.text+0xcea1a): undefined reference to `bad_dma_ops'
stm32-usart.c:(.text+0xcea7a): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/stm32-usart.c: In function ‘stm32_receive_chars’:
drivers/tty/serial/stm32-usart.c:130: warning: comparison is always true due to limited range of data type
drivers/tty/serial/stm32-usart.c: In function ‘stm32_tx_dma_complete’:
drivers/tty/serial/stm32-usart.c:177: warning: comparison is always false due to limited range of data type
stm32_usart_offsets.icr is u8, while UNDEF_REG = ~0 is int, and thus
0xffffffff.
As all registers in stm32_usart_offsets are u8, change the definition of
UNDEF_REG to 0xff to fix this.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
So remove the bogus division.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Petr Písař <ppisar@redhat.com>
Fixes: f8df13e0a9 (tty: Clean console safely)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does a couple of things. First of all, powernv immediately
explodes when running a relocated kernel, because the system reset
exception for handling sleeps does not do correct relocated branches.
Secondly, the sleep handling code trashes the condition and cfar
registers, which we would like to preserve for debugging purposes (for
non-sleep case exception).
This patch changes the exception to use the standard format that saves
registers before any tests or branches are made. It adds the test for
idle-wakeup as an "extra" to break out of the normal exception path.
Then it branches to a relocated idle handler that calls the various
idle handling functions.
After this patch, POWER8 CPU simulator now boots powernv kernel that is
running at non-zero.
Fixes: 948cf67c47 ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Before this patch, we used tlbiel, if we ever ran only on this core.
That was mostly derived from the nohash usage of the same. But is
incorrect, the ISA 3.0 clarifies tlbiel such that:
"All TLB entries that have all of the following properties are made
invalid on the thread executing the tlbiel instruction"
ie. tlbiel only invalidates TLB entries on the current thread. So if the
mm has been used on any other thread (aka. cpu) then we must broadcast
the invalidate.
This bug could lead to invalid TLB entries if a program runs on multiple
threads of a core.
Hence use tlbiel, if we only ever ran on only the current cpu.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It should be ALTIVEC, not ALIVEC.
Cyril explains: If a thread performs a transaction with altivec and then
gets preempted for whatever reason, this bug may cause the kernel to not
re-enable altivec when that thread runs again. This will result in an
altivec unavailable fault, when that fault happens inside a user
transaction the kernel has no choice but to enable altivec and doom the
transaction.
The result is that transactions using altivec may get aborted more often
than they should.
The difficulty in catching this with a selftest is my deliberate use of
the word may above. Optimisations to avoid FPU/altivec/VSX faults mean
that the kernel will always leave them on for 255 switches. This code
prevents the kernel turning it off if it got to the 256th switch (and
userspace was transactional).
Fixes: dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware transactional memory in use")
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As part of interface combination checking, verify any new
interface's beacon intervals. In fact, just always add the
beacon interval since that's harmless.
With this patch, mac80211 is prepared for drivers that set
the min_beacon_int_gcd parameter in interface combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
