The driver assumes that control_data points to the drivers i2c_client struct,
but this is no longer the case since the ASoC core has switched to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For digital only paths we need to make sure the bandgap is enabled prior
to starting the FLL which isn't tied into DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
twl6040 supports 5 playback, and 2 capture channels
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only mono audio can be used for vibra (DL4 channel).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset the twl6040_reg array to hold the chip default values.
The only changed values were for the microphone input selection.
Select no input for the microphones in the twl6040_init_chip function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to write to the vio registers at probe time, since most
them either read only, or shared with MFD or not used.
On the other hand it is a good idea to updated the ASICREV register in
the cache at this time.
After power up we need to restore some registers. Clean up the list to
contain only the registers we are going to restore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. add different clkmux mode handling
SAIF can use two instances to implement full duplex (playback &
recording) and record saif may work on EXTMASTER mode which is
using other saif's BITCLK&LRCLK.
The clkmux mode could be set in pdata->init() in mach-specific code.
For generic saif driver, it only needs to know who is his master
and the master id is also provided in mach-specific code.
2. support playback and capture simutaneously however the sample
rates can not be different due to hw limitation.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8776 supports a continuous range of sample rates rather than
discrete values and supports a wider range of sample rates on the
playback path than is currently supported. Update the constraints on
the DAIs to reflect this.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2c core will clear the clientdata pointer automatically,
we don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ambiguously named variable 'link' is used as a temporary throughout
davinci-pcm -- its presence makes grepping (and groking) the code
difficult.
Replace link with the value of link in almost all sites. The exception
is a couple places where the last-assigned link/chan needs to be
returned by a function -- in these cases, rename to last_link.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to
use snd_soc_register_card() instead of creating a "soc-audio" platform device.
In addition we use platform_device_register_simple() to create a platform
device for the codec. This function will handle putting and deleting the
device automatically which simplifies the error handling in the machine
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To get the PCM module loaded automatically by udev et al. we need to add a
proper MODULE_ALIAS.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_pcm_format_width() to determine the sample size, instead of
checking specify sample formats and assuming that those are the only
valid format.
This change adds support for big-endian architectures (which use the _BE
formats) and the packed 24-bit format (SNDRV_PCM_FORMAT_S24_3xE).
[Fixed single letter variable name legibility problem -- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to count the timeout down.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Fix below build warning:
sound/soc/blackfin/bf5xx-ad73311.c: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_get() returns a pointer to the struct clk or an ERR_PTR().
This patch also use PTR_ERR() for return value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Freescale SSI audio controller supports "synchronous" and "asynchronous"
modes. In synchronous mode, playback and capture use the same input clock,
so sample rates must be the same during simultaneous playback and capture.
Unfortunately, the code which supports asynchronous mode is just broken in
various ways. In particular, it was constraining sample sizes as well as
the sample rate.
The fix also allows us to simplify the code by eliminating the 'asynchronous',
'playback', and 'capture' variables that were used to keep track of playback
and capture streams.
Unfortunately, it turns out that simulataneous playback and record does not
actually work on the only platform that supports asynchronous mode: the
Freescale P1022DS reference board. If a second stream is started, the SSI
grinds to halt for both streams. This is true even if the P1022 is configured
for synchronous mode, so it's likely a hardware problem that needs to be
worked around.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
A fix merged in 3.1-rc2 introduced a small regression, this should get it
to build again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.
This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.
The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error instead of 0 if clk_get fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_pcm_hw_constraint_integer() could return -1, in this case, sst platform is
not opened successfully. However the corresponding close callback isn't able
to be called later on to release these two allocated memories, thus resulting
in memory leak.
This patch moves the check for hardware contraints earlier, thus resolving this
issue.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the builtin snd_soc_set_runtime_hwparams() instead of assigning it by
myself.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if vendor id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't use the step size so there's no need to work it out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
In the case of no free channel available,
current implementation returns 0 instead of negative errno.
This patch fixes the logic to return -EINVAL if no free channel available.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
