There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.
As a precaution, reset all these bits to their default values after
recovery is complete.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using set_scl may be ineffective before calling the driver specific
prepare_recovery callback, which might change into a test mode. So
instead of setting SCL in i2c_generic_scl_recovery, move it to
i2c_generic_recovery (after the optional prepare_recovery).
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change removes redundant sysfs binary file boundary check, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Note, on file size overflow read() now returns 0, and this is a
correct and expected EOF notification according to POSIX.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For write/discard obj_requests that involved a copyup method call, the
opcode of the first op is CEPH_OSD_OP_CALL and the ->callback is
rbd_img_obj_copyup_callback(). The latter frees copyup pages, sets
->xferred and delegates to rbd_img_obj_callback(), the "normal" image
object callback, for reporting to block layer and putting refs.
rbd_osd_req_callback() however treats CEPH_OSD_OP_CALL as a trivial op,
which means obj_request is marked done in rbd_osd_trivial_callback(),
*before* ->callback is invoked and rbd_img_obj_copyup_callback() has
a chance to run. Marking obj_request done essentially means giving
rbd_img_obj_callback() a license to end it at any moment, so if another
obj_request from the same img_request is being completed concurrently,
rbd_img_obj_end_request() may very well be called on such prematurally
marked done request:
<obj_request-1/2 reply>
handle_reply()
rbd_osd_req_callback()
rbd_osd_trivial_callback()
rbd_obj_request_complete()
rbd_img_obj_copyup_callback()
rbd_img_obj_callback()
<obj_request-2/2 reply>
handle_reply()
rbd_osd_req_callback()
rbd_osd_trivial_callback()
for_each_obj_request(obj_request->img_request) {
rbd_img_obj_end_request(obj_request-1/2)
rbd_img_obj_end_request(obj_request-2/2) <--
}
Calling rbd_img_obj_end_request() on such a request leads to trouble,
in particular because its ->xfferred is 0. We report 0 to the block
layer with blk_update_request(), get back 1 for "this request has more
data in flight" and then trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
with rhs (which == ...) being 1 because rbd_img_obj_end_request() has
been called for both requests and lhs (more) being 1 because we haven't
got a chance to set ->xfferred in rbd_img_obj_copyup_callback() yet.
To fix this, leverage that rbd wants to call class methods in only two
cases: one is a generic method call wrapper (obj_request is standalone)
and the other is a copyup (obj_request is part of an img_request). So
make a dedicated handler for CEPH_OSD_OP_CALL and directly invoke
rbd_img_obj_copyup_callback() from it if obj_request is part of an
img_request, similar to how CEPH_OSD_OP_READ handler invokes
rbd_img_obj_request_read_callback().
Since rbd_img_obj_copyup_callback() is now being called from the OSD
request callback (only), it is renamed to rbd_osd_copyup_callback().
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 3.18
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
commit e548e9b93d makes the kclient
only re-send cap flush once during MDS failover. If the kclient sends
a cap flush after MDS enters reconnect stage but before MDS recovers.
The kclient will skip re-sending the same cap flush when MDS recovers.
This causes problem for newly created inode. The MDS handles cap
flushes before replaying unsafe requests, so it's possible that MDS
find corresponding inode is missing when handling cap flush. The fix
is reverting to old behaviour: always re-send when MDS recovers
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
modify_ldt() has questionable locking and does not synchronize
threads. Improve it: redesign the locking and synchronize all
threads' LDTs using an IPI on all modifications.
This will dramatically slow down modify_ldt in multithreaded
programs, but there shouldn't be any multithreaded programs that
care about modify_ldt's performance in the first place.
This fixes some fallout from the CVE-2015-5157 fixes.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/4c6978476782160600471bd865b318db34c7b628.1438291540.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The update_va_mapping hypercall can fail if the VA isn't present
in the guest's page tables. Under certain loads, this can
result in an OOPS when the target address is in unpopulated vmap
space.
While we're at it, add comments to help explain what's going on.
This isn't a great long-term fix. This code should probably be
changed to use something like set_memory_ro.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <dvrabel@cantab.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/0b0e55b995cda11e7829f140b833ef932fcabe3a.1438291540.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
booting because the upper 32-bits of the EFI memmap pointer were
being discarded in setup_e820() - Dmitry Skorodumov
* Validate that the "efi" kernel parameter gets used with an argument,
otherwise we will oops - Ricardo Neri
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kohF
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Fix an EFI boot issue preventing a Parallels virtual machine from
booting because the upper 32-bits of the EFI memmap pointer were
being discarded in setup_e820(). (Dmitry Skorodumov)
* Validate that the "efi" kernel parameter gets used with an argument,
otherwise we will oops. (Ricardo Neri)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kjas
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"There are a couple of recently found, long standing remote attribute
corruption fixes caused by log recovery getting confused after a
crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to
actually use the DAX fault path on read faults.
Summary:
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping"
* tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remote attributes need to be considered data
xfs: remote attribute headers contain an invalid LSN
xfs: call dax_fault on read page faults for DAX
The newsk returned by sk_clone_lock should hold a get_net()
reference if, and only if, the parent is not a kernel socket
(making this similar to sk_alloc()).
E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock
sets up the syn_recv newsk from sk_clone_lock. When the parent (listen)
socket is a kernel socket (defined in sk_alloc() as having
sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt
and should not hold a get_net() reference.
Fixes: 26abe14379 ("net: Modify sk_alloc to not reference count the
netns of kernel sockets.")
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 55334a5db5 ("net_sched: act: refuse to remove bound action
outside"), we end up with a wrong reference count for a tc action.
Test case 1:
FOO="1,6 0 0 4294967295,"
BAR="1,6 0 0 4294967294,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \
action bpf bytecode "$FOO"
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 1 bind 1
tc actions replace action bpf bytecode "$BAR" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
index 1 ref 2 bind 1
tc actions replace action bpf bytecode "$FOO" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 3 bind 1
Test case 2:
FOO="1,6 0 0 4294967295,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 2 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 3 bind 1
What happens is that in tcf_hash_check(), we check tcf_common for a given
index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've
found an existing action. Now there are the following cases:
1) We do a late binding of an action. In that case, we leave the
tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init()
handler. This is correctly handeled.
2) We replace the given action, or we try to add one without replacing
and find out that the action at a specific index already exists
(thus, we go out with error in that case).
In case of 2), we have to undo the reference count increase from
tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to
do so because of the 'tcfc_bindcnt > 0' check which bails out early with
an -EPERM error.
Now, while commit 55334a5db5 prevents 'tc actions del action ...' on an
already classifier-bound action to drop the reference count (which could
then become negative, wrap around etc), this restriction only accounts for
invocations outside a specific action's ->init() handler.
One possible solution would be to add a flag thus we possibly trigger
the -EPERM ony in situations where it is indeed relevant.
After the patch, above test cases have correct reference count again.
Fixes: 55334a5db5 ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: device reset
v3:
For patch #2, remove cancel_delayed_work().
v2:
For patch #1, remove usb_autopm_get_interface(), usb_autopm_put_interface(), and
the checking of intf->condition.
For patch #2, replace the original method with usb_queue_reset_device() to reset
the device.
v1:
Although the driver works normally, we find the device may get all 0xff data when
transmitting packets on certain platforms. It would break the device and no packet
could be transmitted. The reset is necessary to recover the hw for this situation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition. It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131
Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ben was pretty surprised that he is still listed as the maintainer and
he has no objections against transferring the duty to those who
rumaged in and revamped that code in the recent past.
Add kernel/irq/msi.c to the affected files as it's part of the shiny
new hierarchical irqdomain machinery.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Commit d32932d02e ("x86/irq: Convert IOAPIC to use hierarchical
irqdomain interfaces") introduced a regression which causes
malfunction of interrupt lines.
The reason is that the conversion of mp_check_pin_attr() missed to
update the polarity selection of the interrupt pin with the caller
provided setting and instead uses a stale attribute value. That in
turn results in chosing the wrong interrupt flow handler.
Use the caller supplied setting to configure the pin correctly which
also choses the correct interrupt flow handler.
This restores the original behaviour and on the affected
machine/driver (Surface Pro 3, i2c controller) all IOAPIC IRQ
configuration are identical to v4.1.
Fixes: d32932d02e ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
Reported-and-tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Reported-and-tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chen Yu <yu.c.chen@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1438242695-23531-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull input fixes from Dmitry Torokhov:
"The main change is support for keyboards and touchpads found in 2015
editions of Macbooks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: zforce - don't overwrite the stack"
Input: bcm5974 - add support for the 2015 Macbook Pro
HID: apple: Add support for the 2015 Macbook Pro
Input: bcm5974 - prepare for a new trackpad generation
Input: synaptics - dump ext10 capabilities as well
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
__sg_alloc_table() sets both table->nents and table->orig_nents to the
same value. When the scatterlist is DMA-mapped, table->nents is
overwritten with the (possibly smaller) size of the DMA-mapped
scatterlist, while table->orig_nents retains the original size of the
allocated scatterlist. scsi_free_sgtable() should therefore check
orig_nents instead of nents, and all code that initializes sdb->table
without calling __sg_alloc_table() should set both nents and orig_nents.
Fixes: d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fixes another signed / unsigned array indexing bug in the ipr driver.
Currently, when hrrq_index wraps, it becomes a negative number. We
do the modulo, but still have a negative number, so we end up indexing
backwards in the array. Given where the hrrq array is located in memory,
we probably won't actually reference memory we don't own, but nonetheless
ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as
struct ipr_hrr_queue data, so bad things could certainly happen.
Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new
adapters. Let's take an example:
Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4:
The atomic_add_return will then return -1. We mod this with 3 and get -2, add
one and get -1 for an array index.
On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter
initialization and error interrupts so that we can optimize the other queues
for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the
I/O requests across those HRRQs.
With the default module parameter settings, this bug won't hit, only when
someone sets the ipr.number_of_msix parameter to a value larger than 3 is when
bad things start to happen.
Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When ipr's internal driver trace was changed to an atomic, a signed/unsigned
bug slipped in which results in us indexing backwards in our memory buffer
writing on memory that does not belong to us. This patch fixes this by removing
the modulo and instead just mask off the low bits.
Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes
a crash seen as the __devices list in the scsi host was changing as we were
iterating through it.
Cc: <stable@vger.kernel.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Even though it is documented how to specifiy efi parameters, it is
possible to cause a kernel panic due to a dereference of a NULL pointer when
parsing such parameters if "efi" alone is given:
PANIC: early exception 0e rip 10:ffffffff812fb361 error 0 cr2 0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.2.0-rc1+ #450
[ 0.000000] ffffffff81fe20a9 ffffffff81e03d50 ffffffff8184bb0f 00000000000003f8
[ 0.000000] 0000000000000000 ffffffff81e03e08 ffffffff81f371a1 64656c62616e6520
[ 0.000000] 0000000000000069 000000000000005f 0000000000000000 0000000000000000
[ 0.000000] Call Trace:
[ 0.000000] [<ffffffff8184bb0f>] dump_stack+0x45/0x57
[ 0.000000] [<ffffffff81f371a1>] early_idt_handler_common+0x81/0xae
[ 0.000000] [<ffffffff812fb361>] ? parse_option_str+0x11/0x90
[ 0.000000] [<ffffffff81f4dd69>] arch_parse_efi_cmdline+0x15/0x42
[ 0.000000] [<ffffffff81f376e1>] do_early_param+0x50/0x8a
[ 0.000000] [<ffffffff8106b1b3>] parse_args+0x1e3/0x400
[ 0.000000] [<ffffffff81f37a43>] parse_early_options+0x24/0x28
[ 0.000000] [<ffffffff81f37691>] ? loglevel+0x31/0x31
[ 0.000000] [<ffffffff81f37a78>] parse_early_param+0x31/0x3d
[ 0.000000] [<ffffffff81f3ae98>] setup_arch+0x2de/0xc08
[ 0.000000] [<ffffffff8109629a>] ? vprintk_default+0x1a/0x20
[ 0.000000] [<ffffffff81f37b20>] start_kernel+0x90/0x423
[ 0.000000] [<ffffffff81f37495>] x86_64_start_reservations+0x2a/0x2c
[ 0.000000] [<ffffffff81f37582>] x86_64_start_kernel+0xeb/0xef
[ 0.000000] RIP 0xffffffff81ba2efc
This panic is not reproducible with "efi=" as this will result in a non-NULL
zero-length string.
Thus, verify that the pointer to the parameter string is not NULL. This is
consistent with other parameter-parsing functions which check for NULL pointers.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The efi_info structure stores low 32 bits of memory map
in efi_memmap and high 32 bits in efi_memmap_hi.
While constructing pointer in the setup_e820(), need
to take into account all 64 bit of the pointer.
It is because on 64bit machine the function
efi_get_memory_map() may return full 64bit pointer and before
the patch that pointer was truncated.
The issue is triggered on Parallles virtual machine and
fixed with this patch.
Signed-off-by: Dmitry Skorodumov <sdmitry@parallels.com>
Cc: Denis V. Lunev <den@openvz.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
nct7802: Fix integer overflow seen when writing voltage limits
nct7904: Rename pwm attributes to match hwmon ABI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KC6y
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two patches headed for -stable.
nct7802: Fix integer overflow seen when writing voltage limits
nct7904: Rename pwm attributes to match hwmon ABI"
* tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct7802) Fix integer overflow seen when writing voltage limits
hwmon: (nct7904) Rename pwm attributes to match hwmon ABI
The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.
Note that this is a new attempt for the previously merged one,
reverted in
commit d82c0ba6e3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 14 12:29:27 2015 +0200
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about previous (failed attempt).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the device does not support the aliasing ppgtt, we must translate
user bind requests (PIN_USER) from LOCAL_BIND to a GLOBAL_BIND. However,
since this is device specific we cannot do this conveniently in the
upper layers and so must manage the vma->bound flags in the backend.
Partial revert of commit 75d04a3773 [4.2-rc1]
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Apr 28 17:56:17 2015 +0300
drm/i915/gtt: Allocate va range only if vma is not bound
Note this was spotted by Daniel originally, but we dropped the ball in
getting the fix in before the bug going wild. Sorry all.
Reported-by: Vincent Legoll vincent.legoll@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91133
References: https://bugs.freedesktop.org/show_bug.cgi?id=90224
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
pnv_eeh_next_error() re-enables the eeh opal event interrupt but it
gets called from a loop if there are more outstanding events to
process, resulting in a warning due to enabling an already enabled
interrupt. Instead the interrupt should only be re-enabled once the
last outstanding event has been processed.
Tested-by: Daniel Axtens <dja@axtens.net>
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some AMD systems also have non-PCI devices which can do DMA.
Those can't be handled by the AMD IOMMU, as the hardware can
only handle PCI. These devices would end up with no dma_ops,
as neither the per-device nor the global dma_ops will get
set. SWIOTLB provides global dma_ops when it is active, so
make sure there are global dma_ops too when swiotlb is
disabled.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In passthrough mode (iommu=pt) all devices are identity
mapped. If a device does not support 64bit DMA it might
still need remapping. Make sure swiotlb is initialized to
provide this remapping.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since devices with IOMMUv2 functionality might be in the
same group as devices without it, allow those devices in
IOMMUv2 domains too.
Otherwise attaching the group with the IOMMUv2 device to the
domain will fail.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Remove the AMD IOMMU driver implementation for passthrough
mode and rely on the new iommu core features for that.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since the conversion to default domains the
iommu_attach_device function only works for devices with
their own group. But this isn't always true for current
IOMMUv2 capable devices, so use iommu_attach_group instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use proper typecasting while performing byte-by-byte copy
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksey Makarov says:
====================
net: thunderx: Misc fixes
Miscellaneous fixes for the ThunderX VNIC driver
All the patches can be applied individually.
It's ok to drop some if the maintainer feels uncomfortable
with applying for 4.2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cortina phy does not have kernel driver and we don't attach
device with phy layer for intefaces like XFI, XLAUI etc,
Hence check for interface type before calling disconnect.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when changing rss with multiple traffic flows.
While interface teardown, disable tx queues after all NAPI threads
are done. If done otherwise tx queues might be woken up inside NAPI
if any CQE_TX are processed.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a txq (SQ) remains in stopped state after this timeout its
considered as stuck and interface is reinited.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TXQ is wakedup whenever napi is executed
and irrespective of if any CQE_TX are processed or not.
Added 'txq_stop' and 'txq_wake' counters to aid in debugging
if there are any future issues.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
