Add LCD support on Netgear RN104
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXQyyfAAKCRALBhiOFHI7
1ZPaAJ9AaFGTVnIuqe8EjZLOiKdO03oWMgCgm8Eu0d9566U2ibYCHCbHN0FbUpU=
=F0cP
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.3 (part 1)
Add LCD support on Netgear RN104
* tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: netgear-rn104: Add LCD to RN104 dts.
Signed-off-by: Olof Johansson <olof@lixom.net>
arm and arm64, a fix for the array syntax raised by our DT schemas.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXQyRegAKCRDj7w1vZxhR
xQ7SAP9gWeCGiyq+N2lvgFUOMVUezlDcJx2IVjoJvSQcyjeD2QD/W0m+fldHe7BB
PEv3s5BbYAYFHe+krqTPejcLK+c5hwg=
=4UQl
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXQyQTgAKCRDj7w1vZxhR
xYkmAQDT7s1MRH9OEFQpS80BcWCvQoj0drr1ghHdXwwEbfuBUgEAoIuLrfH1Vjyi
ZcEJwPGowLmSEZezVWSLqTL76iajJg4=
=PAul
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.3-201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches:
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
* tag 'sunxi-dt-for-5.3-201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
dt-bindings: pwm: Convert Allwinner PWM to a schema
ARM: dts: sun8i: r40: Change the RTC compatible
ARM: dts: sun8i: v3s: Add external crystals accuracy
ARM: dts: sun8i: v3s: Fix the RTC node
ARM: dts: sun6i: Add external crystals accuracy
ARM: dts: sun6i: Fix RTC node
ARM: dts: sun8i: a83t: Add device node for CSI (Camera Sensor Interface)
ARM: dts: gr8-evb: Fix RTC vendor
ARM: dts: sun7i: icnova-swac: Fix the model vendor
ARM: dts: sun8i: a711: Change LRADC node names to avoid warnings
ARM: dts: sun7i: olimex-lime2: Enable ac and power supplies
ARM: dts: sun6i: Add default address and size cells for SPI
ARM: dts: sun8i-h3: Fix wifi in Beelink X2 DT
dt-bindings: bus: Convert Allwinner RSB to a schema
ARM: dts: sun8i: r40: bananapi-m2-ultra: Remove regulator-always-on
ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth device node
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI output
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller
ARM: dts: sun8i: v40: bananapi-m2-berry: Add GPIO pin-bank regulator supplies
...
Signed-off-by: Olof Johansson <olof@lixom.net>
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
-----BEGIN PGP SIGNATURE-----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=Hwcm
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.3
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
* tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
ARM: dts: aspeed: Add YADRO VESNIN BMC
ARM: dts: aspeed: Add Microsoft Olympus BMC
ARM: dts: aspeed: Adding Lenovo Hr630 BMC
ARM: dts: aspeed: Add Facebook YAMP BMC
ARM: dts: aspeed: swift: Add pca9539 devices
ARM: dts: aspeed: Add Swift BMC machine
ARM: dts: aspeed: cmm: enable ehci host controllers
ARM: dts: aspeed: zaius: fixed I2C bus numbers for pcie slots
ARM: dts: aspeed: zaius: update 12V brick I2C address
ARM: dts: aspeed: zaius: add Infineon and Intersil regulators
ARM: dts: aspeed: quanta-q71: Enable p2a node
ARM: dts: aspeed: Add aspeed-p2a-ctrl node
ARM: dts: aspeed: Add Power9 and Power9 CFAM description
ARM: dts: aspeed: Rename flash-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q1ev
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm Device Tree Changes for v5.3
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
* tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-hammerhead: add support for display
ARM: dts: msm8974: add display support
ARM: dts: qcom: msm8974-hammerhead: add support for backlight
ARM: dts: qcom: msm8974-hammerhead: add touchscreen support
ARM: dts: qcom-msm8974: Update coresight DT bindings
ARM: dts: qcom-apq8064: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vaAE
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs updates for v5.3
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
* tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hip04: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
-----BEGIN PGP SIGNATURE-----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=AQ6F
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contain Broadcom ARM-based SoCs Device Tree changes
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
* tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
ARM: dts: BCM63xx: Fix DTC W=1 warnings
ARM: dts: BCM53573: Fix DTC W=1 warnings
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
ARM: dts: Cygnus: Fix most DTC W=1 warnings
ARM: dts: Fix BCM7445 DTC warnings
ARM: bcm283x: Enable DMA support for SPI controller
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Without this, the driver for the BCM2835 SPI controller uses interrupt
mode instead of DMA mode, incurring a significant performance penalty.
The Foundation's device tree has had these attributes for years, but for
some reason they were never upstreamed.
They were originally contributed by Noralf Trønnes and Martin Sperl:
https://github.com/raspberrypi/linux/commit/25f3e064afc8https://github.com/raspberrypi/linux/commit/e0edb52b47e6
The DREQ numbers 6 and 7 are documented in section 4.2.1.3 of:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 029efb3a03 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 = 18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The fp5280g2 is an OpenPower server platform with an ASPEED AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
-----BEGIN PGP SIGNATURE-----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=22jl
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.3
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
* tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: Add EMAC OCP reset property
ARM: dts: socfpga: add ltc2497 on arria10 devkit
arm64: dts: stratix10: use the "altr,socfpga-stmmac-a10-s10" binding
ARM: dts: socfpga: use the "altr,socfpga-stmmac-a10-s10" binding
Signed-off-by: Olof Johansson <olof@lixom.net>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Samsung DTS ARM changes for v5.3
1. Fixes for minor warnings.
2. Enable ADC on Exynos5410 Odroid XU board.
* tag 'samsung-dt-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add ADC node to Exynos5410 and Odroid XU
ARM: dts: exynos: Raise maximum buck regulator voltages on Arndale Octa
ARM: dts: exynos: Move CPU OPP tables out of SoC node on Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv7 Vexpress updates for v5.3
1. Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
2. Disable NOR flash on Vexpress TC2 platform as it conflicts with CPU
power management. This follows what we have on ARMv8 Juno platform
and is required after recent commit that enabled CFI NOR FLASH in
multi_v7 defconfig
* tag 'vexpress-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: set the right partition type for NOR flash
arm: dts: vexpress-v2p-ca15_a7: disable NOR flash node by default
ARM: dts: vexpress-v2p-ca15_a7: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
ti-sysc dts changes for v5.3
We can now drop the custom dts property "ti,hwmods" for drivers that
have the ti-sysc interconnect target module configured in dts.
Let's start with a minimal changes to omap4 uart and mmc. We use
omap4 as the starting point as it has runtime PM implemented and all
the omap variants after that are based on it with similar clkctrl
clock for the modules. More devices will be updated later on as they
get tested.
Note that these changes are based on the related ti-sysc driver
changes.
* tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Drop legacy custom hwmods property for omap4 mmc
ARM: dts: Drop legacy custom hwmods property for omap4 uart
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
dts changes for omap variants for v5.3
This series of changes improves support for few boards:
- configure another lcd type for logicpd torpedo devkit
- a series of updates for am335x phytec boards
- configure mmc card detect pin for am335x-baltos
* tag 'omap-for-v5.3/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos: add support for MMC1 CD pin
ARM: dts: am335x-baltos: Fix PHY mode for ethernet
ARM: dts: Add support for phyBOARD-REGOR-AM335x
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-phycore-som: Add emmc node
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: Add LCD type 28 support to LogicPD Torpedo DM3730 devkit
Signed-off-by: Olof Johansson <olof@lixom.net>
all over the place.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlz/ZecQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYtuB/9uu5l+8ny2ea/5p11up58Vu97AYffchY4z
PuKTZvLlPGL/oe/7ZBCAZBrWiE2qDXrU+tDGnBGD9ZiF5aTHNNMFMH+GXlUNNQby
2gh3sVxjkesgg4fuMUhoipJVtIzZxh/t/+bKus2OSNTBfYAUY/LuB3MKO4NWSz+j
EnaKtzjV9WBn0K5NDxf6BiU6Inzhud+9xehKd55glwt6XWcvKCC+ejss9IYV+rC+
o/nA9Oz5K3vnJDZZCGKHcloowP5EWNXCXdVdMM1KpoIS0nTCKtO98vJ6Q7YXWIXD
L4Ia8NbqNKUfUhXYDA1MJN2y0dU9AhmptdOKbL/b/qhjenTUYQCT
=02qt
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for rk3288 in general and veyron specially with changes
all over the place.
* tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: Split GPIO keys for veyron into multiple devices
ARM: dts: rockchip: Add HDMI i2c unwedging for rk3288-veyron
ARM: dts: rockchip: Add unwedge pinctrl entries for dw_hdmi on rk3288
ARM: dts: rockchip: Switch to builtin HDMI DDC bus on rk3288-veyron
ARM: dts: rockchip: Add pin names for rk3288-veyron jaq, mickey, speedy
ARM: dts: rockchip: fix pwm-cells for rk3288's pwm3
ARM: dts: rockchip: Configure the GPU thermal zone for mickey
ARM: dts: rockchip: Use the GPU to cool CPU thermal zone of veyron mickey
ARM: dts: rockchip: remove GPU 500 MHz OPP on rk3288
ARM: dts: rockchip: Use GPU as cooling device for the GPU thermal zone of the rk3288
ARM: dts: rockchip: Add #cooling-cells entry for rk3288 GPU
ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend
ARM: dts: rockchip: Add pin names for rk3288-veyron-jerry
ARM: dts: rockchip: Add pin names for rk3288-veyron-minnie
ARM: dts: raise GPU trip point temperature for speedy to 80 degC
ARM: dts: rockchip: raise GPU trip point temperatures for veyron
ARM: dts: rockchip: raise CPU trip point temperature for veyron to 100 degC
ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200
ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
ARM: dts: rockchip: Remove bogus 'i2s_clk_out' from rk3288-veyron-mickey
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the Synaptics RMI4 touchscreen that is found on the
Nexus 5.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable cpufreq-dt support for da850-evm. The cvdd is supplied by the
tps65070 pmic with configurable output voltage. By default da850-evm
boards support frequencies up to 375MHz so enable this operating
point.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the da850-lcdk board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the LEGO EV3 board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a cpu node and operating points to the common da850.dtsi file.
All operating points above 300MHz are disabled by default.
Regulators need to be hooked up on a per-board basis.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Baltos 5221/3220 devices provide CD signal on GPIO2_18.
Baltos 2110 device provides CD signal on GPIO1_15.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY must add both tx and rx delay and not only on the tx clock.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the EMAC's OCP reset property on Arria10. The OCP reset bits are
also needed to correctly bring the EMACs out of reset correctly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the two ltc2497 devices that are on the SoCFPGA Arria10
Socdk board at addresses 0x14 and 0x16.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
