Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=ed22 Rev= 5.00
S: Manufacturer=FTDI
S: Product=MixW RigExpert Tiny
S: SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
)
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove dev_info call on disconnect. The sisusb_dev pointer may have been
set to zero by sisusb_delete at this point causing an oops.
The message does not provide any extra information over the standard USB
subsystem output so removing it does not affect functionality.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle. This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because
(a) about half the time the data toggle bit was correct;
(b) canceling such URBs is unusual; and
(c) the few drivers which cancel these URBs either
[1] do it only as part of shutting down, or
[2] have fault recovery logic, which recovers.
For those transfer types, the toggle is normally written back
into the ED when each TD is retired. But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.
The fix is simple: the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.
(Issue found by leonidv11@gmail.com ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.
This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some boxes the touchpad needs to be reinitialized after resume to make
it function again. This fixes bugzilla #10825.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different tools generate slightly different formats of the isight
firmware. Ensure that the firmware buffer is not overrun, while still
ensuring that the correct amount of data is written if trailing data is
present.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Report-by: Justin Mattock <justinmattock@gmail.com>
Tested-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: fix build bug in USB_ISIGHTFW
-tip tree testing found this build bug:
drivers/built-in.o: In function `isight_firmware_load':
isight_firmware.c:(.text+0x1ade08): undefined reference to `request_firmware'
isight_firmware.c:(.text+0x1adf9c): undefined reference to `release_firmware'
select FW_LOADER in USB_ISIGHTFW.
From: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* wMaxPacketSize is le16; copying it to a field of local structure and then
using that field as host-endian (size of object to be allocated) is broken.
* bMaxPacketSize0 is 8-bit; feeding it to le16_to_cpu() is bogus and since the
result is used as host-endian, it's not even misspelled cpu_to_le16().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit fa38dfcc56.
It wasn't really a regression and David and Alan are still working
through the issues reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.
See also drivers/usb/storage/unusual_devs.h
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've just got a USB GPRS/EDGE modem branded Manufacturer Micromax Model
MMX610U (see http://www.airtel.in/level2_t3data.aspx?path=1/106/179)
working by adding another product ID to pl2303. Modem info reports same
module as Max Arnold's i.e.SIMCOM SIM600 but with product ID 0x0612
(cf Ox0611).
From: Steve Murphy <steve@gnusis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the HP53{00,70} scanner other devices of the OEM Avision require
the USB_QUIRK_STRING_FETCH_255 to correct set a configuration with
"recent" Linux kernels.
Signed-off-by: René Rebe <rene@exactcode.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for rev 2 of an existing unusual_devs entry
enabling ROKR W5s to work. Greg, please apply.
From: Javier Smaldone <javier@smaldone.com.ar>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that the unusual_devs entry for the Motorola M600i needs
another flag. This patch adds it. Thanks to Atte André Jensen
<atte@ballbreaker.dk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1101) updates the unusual_devs entry for the Cypress
ATACB pass-through. The protocol field is changed from US_PR_BULK to
US_PR_DEVICE, since the Cypress devices already set bInterfaceProtocol
to Bulk-only.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1099) fixes a performance regression in ehci-hcd. The
fundamental problem is that queue headers get removed from the
schedule too quickly, since the code checks for a counter advancing
rather than making an actual time-based check. The latency involved
in removing the queue header and then relinking it can severely
degrade certain kinds of workloads.
The patch replaces a simple counter with a timestamp derived from the
controller's uframe value. In addition, the delay for unlinking an
idle queue header is increased from 5 ms to 10 ms; since some
controllers (nVidia) have a latency of up to 1 ms for unlinking, this
reduces the relative impact from 20% to 10%.
Finally, a logical error left over from the IAA watchdog-timer
conversion is corrected. Now the driver will always either unlink an
idle queue header or set up a timer to unlink it later. The old code
would sometimes fail to do either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers. That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).
The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point. It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).
This fixes problems several people have experienced with USB video
applications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd. The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read. But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.
A bit-vector is added for storing the change-suspend feature values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This patch (as1094) changes the output of the "descriptors" binary
attribute. Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.
Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices. So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.
This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.
Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a potential deadlock when the usb_generic driver is unbound
from a device. The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs. If a user task happens to be running an attribute method
at the time, the removal will block until the method returns. But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!
This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.
Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered. So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: CDC WDM driver
USB: ehci-orion: the Orion EHCI root hub does have a Transaction Translator
USB: serial: ch341: New VID/PID for CH341 USB-serial
USB: build fix
USB: pxa27x_udc - Fix Oops
USB: OPTION: fix name of Onda MSA501HS HSDPA modem
USB: add TELIT HDSPA UC864-E modem to option driver
usb-serial: Use ftdi_sio driver for RATOC REX-USB60F
Commit 7329e211b9 ("USB: root hubs don't
lie about their number of TTs") requires the various platform EHCI
glue modules to set ->has_tt if the root hub has a Transaction
Translator.
The Orion EHCI root hub does have a Transaction Translator, so set
->has_tt in ehci_orion_setup(). This fixes oopsing on plugging in a
low speed device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent USB-serial devices using the WinChipHead CH340/CH341 chipset are
being shipped with a new vendor/product ID code pair, but an otherwise
identical device. (This is confirmed by looking at INF for the included
Windows driver.)
Patch is tested and working, both with new and old devices.
Signed-off-by: Michael F. Robbins <mrobbins@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the name of the onda MSA501HS device, I guess it is called
different things in different countries.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Telit UC864-E HDSPA modem support to the option driver.
This lets their customers comply with the GPL instead of having to use a
binary driver from the manufacturer.
Cc: Simon Kissel <kissel@viprinet.com>
Cc: Nico Erfurth <ne@nicoerfurth.de>
Cc: Andrea Ghezzo <TS-EMEA@telit.com>
Cc: Dietmar Staps <Dietmar.Staps@telit.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts 57833ea6b9
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.
Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata(). It fixes all 3 phidget drivers, which all have
the same problem.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to Atmel's high speed UDC driver.
* Issue some missing disconnect() calls. Currently they are only made
when VBUS power goes away (on boards where the driver can sense such
changes), but that's not enough for gadget drivers to clean out all
the state that's needed. Missing calls were:
- After USB reset, before starting enumeration.
- When unregistering a gadget driver, before unbind().
* Don't assume gadget drivers provide disconnect callbacks; make sure
to not call through a null pointer!
* When the driver doesn't provide an unbind() callback, refuse to
unregister it.
Also remove two bogus "error" messages:
* Related to mis-handling of disconnect() ... don't emit error messages
for disconnect() handlers that disable endpoints. All of them should
be doing that; the problem is (unfixed) oddness in atmel_usba_udc.
* Don't emit a diagnostic for a curious and transient nonfatal error
that shows up sometimes with EP0.
Those messages spammed syslog, for no good reason.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor fixes to pxa27x udc driver :
- don't clobber driver model bus_id field
- wrong endianess fix (no functional change; cpu is little-endian)
- double udc disable fix
- resume/suspend fix (OTG hold bit)
- make driver pxa27x dependant (check cpu at runtime)
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Mon, May 12, 2008 at 01:02:22AM -0700, David Brownell wrote:
> On Sunday 11 May 2008, Marcin Slusarz wrote:
> >
> > test_ctrl_queue expects (?) positive and negative errnos.
> > what is going on here?
>
> The sign is just a way to flag something:
>
> /* some faults are allowed, not required */
>
> The negative ones are required. Positive codes are optional,
> in the sense that, depending on how the peripheral happens
> to be implemented, they won't necessarily be triggered.
>
> For example, the test to fetch a device qualifier desriptor
> must succeed if the device is running at high speed. So that
> test is marked as negative. But when it's full speed, it
> could legitimately fail; marked as positive. And so on for
> other tests.
>
> Look at how the codes are *interpreted* to see it work.
Lets document it.
Based on comment from David Brownell <david-b@pacbell.net>.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Microchip has changed the PICDEM FS USB demo device (0x04d8:000c)
to use bulk transfer and not interrupt transfer. So I've updated the libusb
based program here (Post #31).
http://forum.microchip.com/tm.aspx?m=106426&mpage=2
So I believe that the in-kernel ldusb driver will no longer work with the
demo firmware. It should be removed.
Signed-off-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: Michael Hund <MHund@LD-Didactic.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New variant of the 5520 found by Luke Sheldrick.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
