The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b36581df7e ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use clock definitions in i.MX27 DTS files.
Additional changes included in this patch (imx27.dtsi):
- Fix IPG clock for UART6.
- Use EMI_AHB_GATE clock for WEIM.
- Added GPIO_IPG_GATE clock for GPIO nodes. Currently this clock is
not used by the driver, but it can be added in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch removes excess "#address-cells" and "#size-cells" entries
for PMIC, since these entries is not used.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
USB PWR and OC pins are used as GPIOs for different purposes,
so add "disable-over-current" property for OTG node to indicate this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.
Place the USB PHY nodes in the board dts files instead.
Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The hardware is better described if we place the PMIC IRQ GPIO into its own
pingroup.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch converts all i.MX WEIM users to use single naming style
for devices.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds pin group for Synchronous Serial Interface 1 (SSI1)
for PCM-038 module and enables this interface. This change do nothing
at the current stage but helps to continue develop sound support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds USBH2 devicetree node of Phytec PCM970 RDK.
Additionally, adds fixed regulator to provide functionality
without dummy-regulator in the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM-038 module have three triple LEDs connected to PMIC which
can be used for diagnostic purposes. This patch adds support
for these LEDs for PCM-038 SOM and adds basic LED-triggers for
these LEDs for PCM-970 RDK, the remaining LEDs are available
for use from userspace.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since SPI core does not use GPIO bindings for CS GPIOs,
we should add an active high level declaration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pin group for NAND Flash Controller.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM-038 module cannot be used standalone. This patch renames
module file to .dtsi and excludes it from compilation.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
