Add Yellow Carp PCI id support.
v2: add another DID
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
0x1681 has a different external revision id.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A collection of fixes for ASoC that have come in since the merge window,
all driver specific. There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmD4WP0ACgkQJNaLcl1U
h9B2jgf/Xrdc5XdlyICwwyzg5knFNzrj8T5EWDObHRdygPKVidBB45WEK9fLneDq
OCJi4up2SE6aVV0cTjmG9cSfBNP9SUwpVswDimqUQtv/qZDWgNpa6ZIxuzwPk4Rb
BVDTO9BKHOe7JCahIzHxJj0Q7Zstiz6V2C78LAJn2pJm6yzHiWb9ePjeUNvf+9vj
WpPDj20DpvnYjUJ37qvFbj7D+S155X40c3xojHnYFqIG+gJtuwHl3uiklWZrDDON
xwVvpRNQaTX/5PdZ2U/AajTkun98BkqrS6Fpo5mZTjuu2WYqWiRDQTDZbVIGsnLz
iHRiV2pncY68dYkNlQWlSMQ5nNEeHA==
=fKOW
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.14-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.14
A collection of fixes for ASoC that have come in since the merge window,
all driver specific. There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.
Add the USB serial device ID for the CEL ZigBee EM3588 radio stick.
Signed-off-by: John Keeping <john@metanate.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The rework of the ixp46x cpu detection left the network driver in
a half broken state:
drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init':
drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function)
290 | (struct ixp46x_ts_regs __iomem *) IXP4XX_TIMESYNC_BASE_VIRT;
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/xscale/ptp_ixp46x.c: At top level:
drivers/net/ethernet/xscale/ptp_ixp46x.c:323:1: error: data definition has no type or storage class [-Werror]
323 | module_init(ptp_ixp_init);
I have patches to complete the transition for a future release, but
for the moment, add the missing include statements to get it to build
again.
Fixes: 09aa9aabdc ("soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 65d6470d13 ("ibmvnic: clean pending indirect buffs during reset")
intended to remove the call to ibmvnic_tx_scrq_flush() when the
->resetting flag is true and was tested that way. But during the final
rebase to net-next, the hunk got applied to a block few lines below
(which happened to have the same diff context) and the wrong call to
ibmvnic_tx_scrq_flush() got removed.
Fix that by removing the correct ibmvnic_tx_scrq_flush() and restoring
the one that was incorrectly removed.
Fixes: 65d6470d13 ("ibmvnic: clean pending indirect buffs during reset")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko ays:
====================
Fix PMTU for ESP-in-UDP encapsulation
Bug 213669 uncovered regression in PMTU discovery for UDP-encapsulated
routes and some incorrect usage in udp tunnel fields. This series fixes
problems and also adds such case for selftests
v3:
- update checking logic to account SCTP use case
v2:
- remove refactor code that was in first patch
- move checking logic to __udp{4,6}_lib_err_encap
- add more tests, especially routed configuration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The case of ESP in UDP encapsulation was not covered before. Add
cases of local changes of MTU and difference on routed path.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 93b7133041 ("drm/i915: Revert "drm/i915/gem: Asynchronous
cmdparser""), the parameters to intel_engine_cmd_parser() were altered
without updating the docs, causing Fi.CI.DOCS to start failing.
Fixes: c9d9fdbc10 ("drm/i915: Revert "drm/i915/gem: Asynchronous cmdparser"")
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720182108.2761496-1-jason@jlekstrand.net
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Added 'Fixes:' tag and corrected the hash for the ancestor]
(cherry picked from commit 15eb083bdb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Updated Fixes tag to match fixes branch]
Commit d26796ae58 ("udp: check udp sock encap_type in __udp_lib_err")
added checks for encapsulated sockets but it broke cases when there is
no implementation of encap_err_lookup for encapsulation, i.e. ESP in
UDP encapsulation. Fix it by calling encap_err_lookup only if socket
implements this method otherwise treat it as legal socket.
Fixes: d26796ae58 ("udp: check udp sock encap_type in __udp_lib_err")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a call trace:
BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
Call Trace:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:131 [inline]
sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865
sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:723
This is an use-after-free issue caused by not updating asoc->shkey after
it was replaced in the key list asoc->endpoint_shared_keys, and the old
key was freed.
This patch is to fix by also updating active_key for asoc when old key is
being replaced with a new one. Note that this issue doesn't exist in
sctp_auth_del_key_id(), as it's not allowed to delete the active_key
from the asoc.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysfs_remove_link() causes a warning if the parent directory does not
exist. That can happen if the device link consumer has not been registered.
So do not attempt sysfs_remove_link() in that case.
Fixes: 287905e68d ("driver core: Expose device link details in sysfs")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # 5.9+
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Link: https://lore.kernel.org/r/20210716114408.17320-2-adrian.hunter@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rbd_open() and rbd_release() expect that disk->private_data is set to
rbd_dev. Otherwise we hit a NULL pointer dereference when mapping the
image.
URL: https://tracker.ceph.com/issues/51759
Fixes: 195b1956b8 ("rbd: use blk_mq_alloc_disk and blk_cleanup_disk")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver_register() returns with error we need to free the memory
allocated for auxdrv->driver.name before returning from
__auxiliary_driver_register()
Fixes: 7de3697e9c ("Add auxiliary bus support")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210713093438.3173-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is set to -ENOENT and -ENOMEM but this value is never
read as it is overwritten or not used later on, hence it is a
redundant assignment and can be removed.
Cleans up the following clang-analyzer warning:
fs/afs/dir.c:2014:4: warning: Value stored to 'ret' is never read
[clang-analyzer-deadcode.DeadStores].
fs/afs/dir.c:659:2: warning: Value stored to 'ret' is never read
[clang-analyzer-deadcode.DeadStores].
[DH made the following modifications:
- In afs_rename(), -ENOMEM should be placed in op->error instead of ret,
rather than the assignment being removed entirely. afs_put_operation()
will pick it up from there and return it.
- If afs_sillyrename() fails, its error code should be placed in op->error
rather than in ret also.
]
Fixes: e49c7b2f6d ("afs: Build an abstraction around an "operation" concept")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/1619691492-83866-1-git-send-email-jiapeng.chong@linux.alibaba.com
Link: https://lore.kernel.org/r/162609465444.3133237.7562832521724298900.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/162610729052.3408253.17364333638838151299.stgit@warthog.procyon.org.uk/ # v2
To quote Alexey[1]:
I was adding custom tracepoint to the kernel, grabbed full F34 kernel
.config, disabled modules and booted whole shebang as VM kernel.
Then did
perf record -a -e ...
It crashed:
general protection fault, probably for non-canonical address 0x435f5346592e4243: 0000 [#1] SMP PTI
CPU: 1 PID: 842 Comm: cat Not tainted 5.12.6+ #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:t_show+0x22/0xd0
Then reproducer was narrowed to
# cat /sys/kernel/tracing/printk_formats
Original F34 kernel with modules didn't crash.
So I started to disable options and after disabling AFS everything
started working again.
The root cause is that AFS was placing char arrays content into a
section full of _pointers_ to strings with predictable consequences.
Non canonical address 435f5346592e4243 is "CB.YFS_" which came from
CM_NAME macro.
Steps to reproduce:
CONFIG_AFS=y
CONFIG_TRACING=y
# cat /sys/kernel/tracing/printk_formats
Fix this by the following means:
(1) Add enum->string translation tables in the event header with the AFS
and YFS cache/callback manager operations listed by RPC operation ID.
(2) Modify the afs_cb_call tracepoint to print the string from the
translation table rather than using the string at the afs_call name
pointer.
(3) Switch translation table depending on the service we're being accessed
as (AFS or YFS) in the tracepoint print clause. Will this cause
problems to userspace utilities?
Note that the symbolic representation of the YFS service ID isn't
available to this header, so I've put it in as a number. I'm not sure
if this is the best way to do this.
(4) Remove the name wrangling (CM_NAME) macro and put the names directly
into the afs_call_type structs in cmservice.c.
Fixes: 8e8d7f13b6 ("afs: Add some tracepoints")
Reported-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/YLAXfvZ+rObEOdc%2F@localhost.localdomain/ [1]
Link: https://lore.kernel.org/r/643721.1623754699@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/162430903582.2896199.6098150063997983353.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/162609463957.3133237.15916579353149746363.stgit@warthog.procyon.org.uk/ # v1 (repost)
Link: https://lore.kernel.org/r/162610726860.3408253.445207609466288531.stgit@warthog.procyon.org.uk/ # v2
Commit 1be7107fbe ("mm: larger stack guard gap, between vmas") fixed
up all architectures to deal with the stack guard gap. But when nds32
was added to the tree, it forgot to do the same thing.
Resolve this by properly fixing up the nsd32's version of
arch_get_unmapped_area()
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Qiang Liu <cyruscyliu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: iLifetruth <yixiaonn@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Link: https://lore.kernel.org/r/20210629104024.2293615-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add maintainer info for the VMware VMCI driver.
v2: moved pv-drivers to L: as private list
Acked-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/1626861766-11115-1-git-send-email-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI reads the channel ID from the event ring element sent by the
device which can be any value between 0 and 255. In order to
prevent any out of bound accesses, add a check against the maximum
number of channels supported by the controller and those channels
not configured yet so as to skip processing of that event ring
element.
Link: https://lore.kernel.org/r/1624558141-11045-1-git-send-email-bbhatt@codeaurora.org
Fixes: 1d3173a3ba ("bus: mhi: core: Add support for processing events from client device")
Cc: stable@vger.kernel.org #5.10
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210716075106.49938-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices such as SDX24 do not have the provision for inband wake
doorbell in the form of channel 127 and instead have a sideband
GPIO for it. Newer devices such as SDX55 or SDX65 support inband
wake method by default. Ensure the functionality is used based on
this such that device wake stays held when a client driver uses
mhi_device_get() API or the equivalent debugfs entry.
Link: https://lore.kernel.org/r/1624560809-30610-1-git-send-email-bbhatt@codeaurora.org
Fixes: e3e5e6508f ("bus: mhi: pci_generic: No-Op for device_wake operations")
Cc: stable@vger.kernel.org #5.12
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210716075106.49938-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My local syzbot instance hit GPF in ttm_bo_release().
Unfortunately, syzbot didn't produce a reproducer for this, but I
found out possible scenario:
drm_gem_vram_create() <-- drm_gem_vram_object kzalloced
(bo embedded in this object)
ttm_bo_init()
ttm_bo_init_reserved()
ttm_resource_alloc()
man->func->alloc() <-- allocation failure
ttm_bo_put()
ttm_bo_release()
ttm_mem_io_free() <-- bo->resource == NULL passed
as second argument
*GPF*
Added NULL check inside ttm_mem_io_free() to prevent reported GPF and
make this function NULL save in future.
Same problem was in ttm_bo_move_to_lru_tail() as Christian reported.
ttm_bo_move_to_lru_tail() is called in ttm_bo_release() and mem pointer
can be NULL as well as in ttm_mem_io_free().
Fail log:
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
...
RIP: 0010:ttm_mem_io_free+0x28/0x170 drivers/gpu/drm/ttm/ttm_bo_util.c:66
..
Call Trace:
ttm_bo_release+0xd94/0x10a0 drivers/gpu/drm/ttm/ttm_bo.c:422
kref_put include/linux/kref.h:65 [inline]
ttm_bo_put drivers/gpu/drm/ttm/ttm_bo.c:470 [inline]
ttm_bo_init_reserved+0x7cb/0x960 drivers/gpu/drm/ttm/ttm_bo.c:1050
ttm_bo_init+0x105/0x270 drivers/gpu/drm/ttm/ttm_bo.c:1074
drm_gem_vram_create+0x332/0x4c0 drivers/gpu/drm/drm_gem_vram_helper.c:228
Fixes: d3116756a7 ("drm/ttm: rename bo->mem and make it a pointer")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210708112518.17271-1-paskripkin@gmail.com
This reverts commit c742199a01.
c742199a01 ("mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge")
breaks arm64 in at least two ways for configurations where PUD or PMD
folding occur:
1. We no longer install huge-vmap mappings and silently fall back to
page-granular entries, despite being able to install block entries
at what is effectively the PGD level.
2. If the linear map is backed with block mappings, these will now
silently fail to be created in alloc_init_pud(), causing a panic
early during boot.
The pgtable selftests caught this, although a fix has not been
forthcoming and Christophe is AWOL at the moment, so just revert the
change for now to get a working -rc3 on which we can queue patches for
5.15.
A simple revert breaks the build for 32-bit PowerPC 8xx machines, which
rely on the default function definitions when the corresponding
page-table levels are folded, since commit a6a8f7c4aa ("powerpc/8xx:
add support for huge pages on VMAP and VMALLOC"), eg:
powerpc64-linux-ld: mm/vmalloc.o: in function `vunmap_pud_range':
linux/mm/vmalloc.c:362: undefined reference to `pud_clear_huge'
To avoid that, add stubs for pud_clear_huge() and pmd_clear_huge() in
arch/powerpc/mm/nohash/8xx.c as suggested by Christophe.
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: c742199a01 ("mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
[mpe: Fold in 8xx.c changes from Christophe and mention in change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/linux-arm-kernel/CAMuHMdXShORDox-xxaeUfDW3wx2PeggFSqhVSHVZNKCGK-y_vQ@mail.gmail.com/
Link: https://lore.kernel.org/r/20210717160118.9855-1-jonathan@marek.ca
Link: https://lore.kernel.org/r/87r1fs1762.fsf@mpe.ellerman.id.au
Signed-off-by: Will Deacon <will@kernel.org>
Commit cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register
saving hint") added a call to __arm_smccc_sve_check() which clobbers the
lr (register x30), causing __arm_smccc_hvc() to return to itself and
crash. Save lr on the stack before calling __arm_smccc_sve_check(). Save
the frame pointer (x29) to complete the frame record, and adjust the
offsets used to access stack parameters.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Fixes: cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210721071834.69130-1-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
This reverts commit 0bd860493f.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gcc report build error as following when CONFIG_WWAN_CORE is not set:
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_disconnect':
cdc-wdm.c:(.text+0xb2a): undefined reference to `wwan_remove_port'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_in_callback':
cdc-wdm.c:(.text+0xf23): undefined reference to `wwan_port_rx'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_wwan_port_stop':
cdc-wdm.c:(.text+0x127d): undefined reference to `wwan_port_get_drvdata'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_wwan_port_tx':
cdc-wdm.c:(.text+0x12d9): undefined reference to `wwan_port_get_drvdata'
x86_64-linux-gnu-ld: cdc-wdm.c:(.text+0x13c1): undefined reference to `wwan_port_txoff'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_wwan_port_start':
cdc-wdm.c:(.text+0x13e0): undefined reference to `wwan_port_get_drvdata'
x86_64-linux-gnu-ld: cdc-wdm.c:(.text+0x1431): undefined reference to `wwan_port_txon'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_wwan_port_tx_complete':
cdc-wdm.c:(.text+0x14a4): undefined reference to `wwan_port_txon'
x86_64-linux-gnu-ld: drivers/usb/class/cdc-wdm.o: in function `wdm_create.cold':
cdc-wdm.c:(.text.unlikely+0x209): undefined reference to `wwan_create_port'
Using CONFIG_WWAN_CORE instead of CONFIG_WWAN to avoid build error.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210521021010.2490930-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eb9b7bfd59 as it
breaks working userspace implementations (i.e. Android systems)
The device node name here is part of configfs, so it is a user-visable
api that can not be changed.
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/CALAqxLX_FNvFndEDWtGbFPjSzuAbfqxQE07diBJFZtftwEJX5A@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sending zero length packet in DDMA mode perform by DMA descriptor
by setting SP (short packet) flag.
For DDMA in function dwc2_hsotg_complete_in() does not need to send
zlp.
Tested by USBCV MSC tests.
Fixes: f71b5e2533 ("usb: dwc2: gadget: fix zero length packet transfers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/967bad78c55dd2db1c19714eee3d0a17cf99d74a.1626777738.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr
function.") changed the way the driver handles power down modes in a such
way that it uses clock gating when no other power down mode is available.
This however doesn't work well on the DWC2 implementation used on the
Samsung SoCs. When a clock gating is enabled, system hangs. It looks that
the proper clock gating requires some additional glue code in the shared
USB2 PHY and/or Samsung glue code for the DWC2. To restore driver
operation on the Samsung SoCs simply skip enabling clock gating mode
until one finds what is really needed to make it working reliably.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable <stable@vger.kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210716050127.4406-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af3260528 ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90d ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of dwc2_hsotg_ep_stop_xfr() function uses poll
mode, first need to mask GINTSTS_GOUTNAKEFF interrupt.
In Slave mode GINTSTS_GOUTNAKEFF interrupt will be
aserted only after pop OUT NAK status packet from RxFIFO.
In dwc2_hsotg_ep_sethalt() function before setting
DCTL_SGOUTNAK need to unmask GOUTNAKEFF interrupt.
Tested by USBCV CH9 and MSC tests set in Slave, BDMA and DDMA.
All tests are passed.
Fixes: a4f8277145 ("usb: dwc2: gadget: Disable enabled HW endpoint in dwc2_hsotg_ep_disable")
Fixes: 6070636c49 ("usb: dwc2: Fix Stalling a Non-Isochronous OUT EP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e17fad802bbcaf879e1ed6745030993abb93baf8.1626152924.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
