Some UFS deivces may have required device quirks or have non-standard
features which are enabled only on specified UFS hosts or for special
customers.
To not "pollute" common device quirk list, i.e. ufs_fixups table, for those
devices mentioned above, introduce "fixup_dev_quirks" vops to allow vendors
to fix or modify device quirks accordingly.
Link: https://lore.kernel.org/r/20200508080115.24233-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The WriteBooster feature can be supported by some pre-3.1 UFS devices by
upgrading firmware.
To enable WriteBooster feature in such devices, introduce a device quirk to
relax the entrance condition of ufshcd_wb_probe() to allow host driver to
check those devices' WriteBooster capability.
WriteBooster feature can be available if below all conditions are
satisfied,
1. Host enables WriteBooster capability
2. UFS 3.1 device or UFS pre-3.1 device with quirk
UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES enabled
3. The device descriptor shall have DEVICE_DESC_PARAM_EXT_UFS_FEATURE_SUP
field
4. WriteBooster support is specified in above field
Link: https://lore.kernel.org/r/20200508080115.24233-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in which
the sizeof operator is being incorrectly/erroneously applied to zero-length
arrays and the result is zero. Such instances may be hiding some bugs. So,
this work (flexible-array member conversions) will also help to get
completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200507192550.GA16683@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The write performance of TLC NAND is considerably lower than SLC NAND.
Using SLC NAND as a WriteBooster Buffer enables the write request to be
processed with lower latency and improves the overall write performance.
Adds support for shared-buffer mode WriteBooster.
WriteBooster enable: SW enables it when clocks are scaled up, thus it's
enabled only in high load conditions.
WriteBooster disable: SW will disable the feature, when clocks are scaled
down. Thus writes would go as normal writes.
To keep the endurance of the WriteBooster Buffer at a maximum, this
load-based toggling is adopted.
Link: https://lore.kernel.org/r/2871444d9083b0e9323ef6d8ff1b544b7784adc9.1587591527.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
drivers/scsi/ufs/ufshcd.c:4140:6-14: WARNING: Assignment of 0/1 to bool
variable.
Link: https://lore.kernel.org/r/20200426094305.24083-1-yanaijie@huawei.com
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During suspend, if the link is put to off, it would require a full
initialization during resume. This patch resets and restores both the host
and the card during initialization, otherwise host-only reset and restore
would fail occasionally.
Link: https://lore.kernel.org/r/1586844892-22720-1-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split. It's basically driver updates to lpfc, target, bnx2fc and ufs
with the rest being minor updates except the sr_block_release one
which fixes a use after free introduced by the removal of the global
mutex in the first patch set.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXpC3hSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRTaAP9umhxu
8rRnJ5hsxXRmxOUzO5BGe403ffcBeAiEKQ2n3gEAjeoxZAaqKuDDDRfXyRnBpt9Z
QuBrgpm1gdXrJT5DDj4=
=+4Qg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split.
It's basically driver updates to lpfc, target, bnx2fc and ufs with the
rest being minor updates except the sr_block_release one which fixes a
use after free introduced by the removal of the global mutex in the
first patch set"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (35 commits)
scsi: core: Add DID_ALLOC_FAILURE and DID_MEDIUM_ERROR to hostbyte_table
scsi: ufs: Use ufshcd_config_pwr_mode() when scaling gear
scsi: bnx2fc: fix boolreturn.cocci warnings
scsi: zfcp: use fallthrough;
scsi: aacraid: do not overwrite retval in aac_reset_adapter()
scsi: sr: Fix sr_block_release()
scsi: aic7xxx: Remove more FreeBSD-specific code
scsi: mpt3sas: Fix kernel panic observed on soft HBA unplug
scsi: ufs: set device as active power mode after resetting device
scsi: iscsi: Report unbind session event when the target has been removed
scsi: lpfc: Change default SCSI LUN QD to 64
scsi: libfc: rport state move to PLOGI if all PRLI retry exhausted
scsi: libfc: If PRLI rejected, move rport to PLOGI state
scsi: bnx2fc: Update the driver version to 2.12.13
scsi: bnx2fc: Fix SCSI command completion after cleanup is posted
scsi: bnx2fc: Process the RQE with CQE in interrupt context
scsi: target: use the stack for XCOPY passthrough cmds
scsi: target: increase XCOPY I/O size
scsi: target: avoid per-loop XCOPY buffer allocations
scsi: target: drop xcopy DISK BLOCK LENGTH debug
...
update changing all our txt files to rst ones. Excluding that, we
have the usual driver updates (qla2xxx, ufs, lpfc, zfcp, ibmvfc,
pm80xx, aacraid), a treewide update for scnprintf and some other minor
updates. The major core update is Hannes moving functions out of the
aacraid driver and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXoYKiyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSasAP4iGwSB
Y8tFaZgWadu76+wj5MdqTBoXdhnIuFF0rZG3pQEAiIKdsfQlbSFdm75+gUtx5hG/
GOilX/pJczTRJDCGNis=
=g7Sk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series has a huge amount of churn because it pulls in Mauro's doc
update changing all our txt files to rst ones.
Excluding that, we have the usual driver updates (qla2xxx, ufs, lpfc,
zfcp, ibmvfc, pm80xx, aacraid), a treewide update for scnprintf and
some other minor updates.
The major core change is Hannes moving functions out of the aacraid
driver and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (223 commits)
scsi: aic7xxx: aic97xx: Remove FreeBSD-specific code
scsi: ufs: Do not rely on prefetched data
scsi: dc395x: remove dc395x_bios_param
scsi: libiscsi: Fix error count for active session
scsi: hpsa: correct race condition in offload enabled
scsi: message: fusion: Replace zero-length array with flexible-array member
scsi: qedi: Add PCI shutdown handler support
scsi: qedi: Add MFW error recovery process
scsi: ufs: Enable block layer runtime PM for well-known logical units
scsi: ufs-qcom: Override devfreq parameters
scsi: ufshcd: Let vendor override devfreq parameters
scsi: ufshcd: Update the set frequency to devfreq
scsi: ufs: Resume ufs host before accessing ufs device
scsi: ufs-mediatek: customize the delay for enabling host
scsi: ufs: make HCE polling more compact to improve initialization latency
scsi: ufs: allow custom delay prior to host enabling
scsi: ufs-mediatek: use common delay function
scsi: ufs: introduce common and flexible delay function
scsi: ufs: use an enum for host capabilities
scsi: ufs: fix uninitialized tx_lanes in ufshcd_disable_tx_lcc()
...
When scaling gear, use ufshcd_config_pwr_mode() instead of
ufshcd_change_power_mode() so that vops_pwr_change_notify(PRE_CHANGE)
can be utilized to allow vendors use customized settings before
changing power mode.
Link: https://lore.kernel.org/r/1581485910-8307-2-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently ufshcd driver assumes that bInitPowerMode parameter is not
changed by any vendors thus device power mode can be set as "Active" during
initialization.
According to UFS JEDEC specification, device power mode shall be "Active"
after HW Reset is triggered if the bInitPowerMode parameter in Device
Descriptor is default value.
By above description, we can set device power mode as "Active" after device
reset is triggered by vendor's callback. With this change, the link startup
performance can be improved in some cases by not setting link_startup_again
as true in ufshcd_link_startup().
Link: https://lore.kernel.org/r/20200327095835.10293-1-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export ufshcd_link_recovery to allow vendors to recover failed link in
vendor's callbacks.
Link: https://lore.kernel.org/r/20200327095329.10083-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change introduces a func ufshcd_set_clk_freq() to explicitly set clock
frequency so that it can be used in reset_and_restore path and in
ufshcd_scale_clks(). This change also cleans up the clock scaling error out
path.
[mkp: commit desc]
Link: https://lore.kernel.org/r/1585214742-5466-2-git-send-email-cang@codeaurora.org
Fixes: a3cd5ec55f ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We were setting bActiveICCLevel attribute for UFS device only once but the
type of this attribute has changed from persistent to volatile since UFS
device specification v2.1. This attribute is set to the default value after
power cycle or hardware reset event. It isn't safe to rely on prefetched
data (only used for bActiveICCLevel attribute now). Hence this change
removes the code related to data prefetching and set this parameter on
every attempt to probe the UFS device.
Tested-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Block layer RPM is enabled for the genernal UFS SCSI devices when they are
probed by their driver. However block layer RPM is not enabled for UFS
well-known SCSI devices.
As UFS SCSI devices have their corresponding BSG char devices, accessing a
BSG char device via IOCTL may send requests to its corresponding SCSI
device through its request queue. If BSG IOCTL sends a request to a
well-known SCSI device when HBA is not runtime active, due to block layer
RPM not being enabled for the well-known SCSI devices, the HBA, which is at
the top of a SCSI device's parent chain, will not be resumed.
This change enables block layer RPM for the well-known SCSI devices so that
block layer can handle RPM for the well-known SCSI devices just like for
the general SCSI devices.
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the frequency that devfreq provides the driver always leads the
clocks to be scaled up. Hence, round the clock-rate to the nearest
frequency before deciding to scale.
Also update the devfreq statistics of current frequency.
Link: https://lore.kernel.org/r/d0c6c22455811e9f0eda01f9bc70d1398b51b2bd.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the waiting period between each HCE (Host Controller Enable) polling
from 5 ms to 1 ms. Also increase the maximum polling times to make "total
polling time" roughly the same.
This change could make HCE initialization faster to improve latency of
ufshcd initialization, error recovery, and resume behaviors.
Link: https://lore.kernel.org/r/20200318104016.28049-7-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a 1 ms delay is applied before polling CONTROLLER_ENABLE
bit. This delay may not be required or can be changed in different
controllers. Make the delay as a changeable value in struct ufs_hba to
allow it customized by vendors.
Link: https://lore.kernel.org/r/20200318104016.28049-6-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a common delay function to provide flexible way for users to take
choices of udelay and usleep_range into consideration according to the
required delay time.
Link: https://lore.kernel.org/r/20200318104016.28049-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_disable_tx_lcc(), if ufshcd_dme_get() or ufshcd_dme_peer_get()
get fail, uninitialized variable "tx_lanes" may be used as unexpected lane
ID for DME configuration.
Fix this issue by initializing "tx_lanes".
Link: https://lore.kernel.org/r/20200318104016.28049-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before access auto hibner8 timer register, make sure power and clock are
properly configured to avoid unclocked register access.
Link: https://lore.kernel.org/r/1583398391-14273-1-git-send-email-cang@codeaurora.org
Fixes: ba7af5ec51 ("scsi: ufs: export ufshcd_auto_hibern8_update for vendor usage")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lrbp->cmd is set only for SCSI commands. Use this knowledge to simplify two
boolean expressions.
Link: https://lore.kernel.org/r/20200123035637.21848-4-bvanassche@acm.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but makes the next patch in
this series easier to read.
Link: https://lore.kernel.org/r/20200123035637.21848-3-bvanassche@acm.org
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently ufshcd_vops_apply_dev_quirks() comes after all UniPro parameters
have been tuned. Move it up so that vendors have a chance to apply device
quirks in advance.
Link: https://lore.kernel.org/r/1582517363-11536-2-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove various quirks that don't have users, as well as the dead code keyed
off them.
Link: https://lore.kernel.org/r/20200221140812.476338-2-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In UFS version 3.0, a newly added attribute bRefClkGatingWaitTime defines
the minimum time for which the reference clock is required by device during
transition to LS-MODE or HIBERN8 state. Make this change to reflect the new
requirement by adding delays before turning off the clock.
Link: https://lore.kernel.org/r/1581392451-28743-7-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.
Fixes: f2a785ac23 ("scsi: ufshcd: Fix race between clk scaling and ungate work")
Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functionality of vendor specific ops should be handled properly in
platform specific driver, but should not count on the UFS driver.
Link: https://lore.kernel.org/r/1581392451-28743-5-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This sequence change is required to avoid dips in voltage during boot-up.
Apparently, this dip is caused because in the original sequence, the
regulators are initialized in lpm mode. And then when the load is set to
high, and more current is drawn, than is allowed in lpm, the dip is seen.
Link: https://lore.kernel.org/r/1581392451-28743-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Exception event can be raised by the device when system suspend is in
progress. This will result in unclocked register access in exception event
handler as clocks will be turned off during suspend. This change makes sure
to flush exception event handler work in suspend before disabling clocks to
avoid unclocked register access issue.
Link: https://lore.kernel.org/r/1581392451-28743-2-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Auto-Hibern8 may be disabled by some vendors or sysfs in runtime even if
Auto-Hibern8 capability is supported by host. If Auto-Hibern8 capability is
supported by host but not actually enabled, Auto-Hibern8 error shall not
happen.
To fix this, provide a way to detect if Auto-Hibern8 is actually enabled
first, and bypass Auto-Hibern8 disabling case in
ufshcd_is_auto_hibern8_error().
Fixes: 8217444039 ("scsi: ufs: Add error-handling of Auto-Hibernate")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200129105251.12466-4-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to Jedec standard UFS 3.0 and UFS 2.1 Spec, Maximum number of
logical units supported by the UFS device is indicated by parameter
bMaxNumberLU in Geometry Descriptor. This patch is to delete current hard
code macro definition of UFS_UPIU_MAX_GENERAL_LUN, and switch to use device
indicated number instead.
Link: https://lore.kernel.org/r/20200120130820.1737-9-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add one new parameter max_lu_supported in struct ufs_dev_info, which will
be used to express exactly how many general LUs being supported by UFS
device, and initialize it during booting stage. This patch also adds a new
function ufshcd_device_geo_params_init() for initialization of UFS device
geometry descriptor related parameters.
Link: https://lore.kernel.org/r/20200120130820.1737-8-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without variable is_init_prefetch, the current logic can guarantee
ufshcd_init_icc_levels() will execute only once, delete it now.
Link: https://lore.kernel.org/r/20200120130820.1737-7-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete ufshcd_read_power_desc() and ufshcd_read_device_desc(), directly
inline ufshcd_read_desc() into its callers.
Link: https://lore.kernel.org/r/20200120130820.1737-6-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_max_pwr_mode() only need to be called once while booting, take
it out from ufshcd_probe_hba() and inline into ufshcd_device_params_init().
Link: https://lore.kernel.org/r/20200120130820.1737-5-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has two major non-functionality changes:
1. Take scanning host if-statement out from ufshcd_probe_hba(), and move
into a new added function ufshcd_add_lus(). In this new function
ufshcd_add_lus(), the main functionalitis include: ICC initialization, add
well-known LUs, devfreq initialization, UFS bsg probe and scsi host
scan. The reason for this change is that these functionalities only being
called during booting stage flow ufshcd_init()->ufshcd_async_scan(). In the
processes of error handling and power management ufshcd_suspend(),
ufshcd_resume(), ufshcd_probe_hba() being called, but these functionalitis
above metioned are not hit.
2. Move context of initialization of parameters associated with the UFS
device to a new added function ufshcd_device_params_init(). The reason of
this change is that all of these parameters are used by driver, but only
need to be initialized once when booting. Combine them into an integral
function, make them easier maintain.
Link: https://lore.kernel.org/r/20200120130820.1737-4-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In consideration of UFS host driver uses parameters of struct ufs_dev_desc,
move its parameters to struct ufs_dev_info, delete struct ufs_dev_desc.
Link: https://lore.kernel.org/r/20200120130820.1737-3-huobean@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A non-zero error value likely being returned by ufshcd_scsi_add_wlus() in
case of failure of adding the WLs, but ufshcd_probe_hba() doesn't use this
value, and doesn't report this failure to upper caller. This patch is to
fix this issue.
Fixes: 2a8fa60044 ("ufs: manually add well known logical units")
Link: https://lore.kernel.org/r/20200120130820.1737-2-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export below functions for vendor usage:
int ufshcd_hba_enable(struct ufs_hba *hba);
int ufshcd_make_hba_operational(struct ufs_hba *hba);
int ufshcd_uic_hibern8_exit(struct ufs_hba *hba);
Link: https://lore.kernel.org/r/20200117035108.19699-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass UFS device information to vendor-specific variant callback
"apply_dev_quirks" because some platform vendors need to know such
information to apply special handling or quirks in specific devices.
At the same time, modify existing vendor implementations according to the
new interface for those vendor drivers which will be built-in or built as a
module alone with UFS core driver.
[mkp: clarified commit desc]
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578726707-6596-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove "errors" word in output string by ufshcd_print_err_hist() since not
all printed targets are "errors". Sometimes they are just "events".
In addition, all events which can be treated as "errors" already have "err"
or "fail" words in their names.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-4-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device reset history shall be also added for vendor's device reset variant
operation implementation.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently checking if an error history element is empty or not is by its
"value". In most cases, value is error code.
However this checking is not correct because some errors or events do not
specify any values in error history so values remain as 0, and this will
lead to incorrect empty checking.
Fix it by checking "timestamp" instead of "value" because timestamp will be
always assigned for all history elements
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export ufshcd_auto_hibern8_update to allow vendors to use common interface
to customize auto-hibernate timer.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1577683950-1702-5-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS SCSI timeout handler was needed to compensate that
ufshcd_queuecommand() could return SCSI_MLQUEUE_HOST_BUSY for a long
time. Commit a276c19e3e98 ("scsi: ufs: Avoid busy-waiting by eliminating
tag conflicts") fixed this so the timeout handler is no longer necessary.
See also commit f550c65b54 ("scsi: ufs: implement scsi host timeout handler").
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-7-bvanassche@acm.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Starting execution of a command before tracing a command may cause the
completion handler to free data while it is being traced. Fix this race by
tracing a command before it is submitted.
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-5-bvanassche@acm.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the lrbp->cmd expression occurs multiple times, introduce a new local
variable to hold that pointer. This patch does not change any
functionality.
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-4-bvanassche@acm.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the lrbp->cmd expression occurs multiple times, introduce a new local
variable to hold that pointer. This patch does not change any
functionality.
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-3-bvanassche@acm.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove a space that occurs after a tab.
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191224220248.30138-2-bvanassche@acm.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhar <alim.akhtar@samsung.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already have ufshcd_vops_dbg_register_dump() thus all
"hba->vops->dbg_register_dump" references can be replaced by it.
Link: https://lore.kernel.org/r/1577192466-20762-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently UFS driver has ufshcd_scsi_block_requests() with reference
counter mechanism to avoid possible racing of blocking and unblocking
requests flow. Unify all users in UFS driver to use the same function.
Link: https://lore.kernel.org/r/1577192466-20762-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to suspend, ufshcd interrupt can be disabled since there won't be
any host controller transaction expected till clocks ungated.
Link: https://lore.kernel.org/r/1575721321-8071-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During suspend flow, interrupt shall be disabled before disabling clocks to
avoid potential system hang due to accessing host registers after host
clocks are disabled.
For example, if an interrupt comes with IRQF_IRQPOLL flag configured with
the misrouted interrupt recovery feature enabled, ufshcd ISR may be
triggered even if nothing shall be done for UFS. In this case, system hang
may happen if UFS interrupt status register is accessed with host clocks
disabled.
Link: https://lore.kernel.org/r/1575721321-8071-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We know that "check_for_bkops" is non-zero on this side of the || because
it was checked on the other side.
Link: https://lore.kernel.org/r/20191213104935.wgpq2epaz6zh5zus@kili.mountain
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We introduced a few new error paths, but we can't return directly, we first
have to unlock "hba->clk_scaling_lock" first.
Fixes: a276c19e3e98 ("scsi: ufs: Avoid busy-waiting by eliminating tag conflicts")
Link: https://lore.kernel.org/r/20191213104828.7i64cpoof26rc4fw@kili.mountain
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ufshcd irq resource is allocated with the device resource management
aware IRQ request implementation, we don't really need to free up irq
during suspend, disabling it during suspend and reenabling it during resume
should be good enough.
Link: https://lore.kernel.org/r/0101016ed3d69793-22918f99-23bf-495d-8a36-a9c108d1cbce-000000@us-west-2.amazonses.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During power mode change, PACP_PWR_Req frame sends PAPowerModeUserData
parameters (and they are considered valid by device if Flags[4] -
UserDataValid bit is set in the same frame). Currently we don't set these
PAPowerModeUserData parameters and hardware always sets UserDataValid bit
which would clear all the DL layer timeout values of the peer device after
the power mode change.
This change sets the PAPowerModeUserData[0..5] to UniPro specification
recommended default values, in addition we are also setting the relevant
DME_LOCAL_* timer attributes as required by UFS HCI specification.
Link: https://lore.kernel.org/r/0101016ed3d688a4-cfaeb1c9-238b-46c4-9c89-d48c410ba325-000000@us-west-2.amazonses.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS standard requires DBD field to be set to 1 in MODE SENSE(10).
Some card vendors are more strict and check the DBD field, hence respond
with CHECK_CONDITION (Sense key set to ILLEGAL_REQUEST and ASC set to
INVALID FIELD IN CDB). When host sends MODE SENSE for page caching, as a
result of the CHECK_CONDITION response, host assumes that the device
doesn't support the cache feature and doesn't send SYNCHRONIZE_CACHE
commands to flush the device cache. This can result in data corruption in
case of sudden power down when there is data stored in the device cache.
This patch fixes the DBD field setting as required in UFS standard.
Link: https://lore.kernel.org/r/0101016ed3d657e4-32a6dd52-1505-4312-97ff-2bd3bee59eb7-000000@us-west-2.amazonses.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In UFS host reset and restore path, before probe, we stop and start the
host controller once. After host controller is stopped, the pending
requests, if any, are cleared from the doorbell, but no completion IRQ
would be raised due to the hba is stopped. These pending requests shall be
completed along with the first NOP_OUT command (as it is the first command
which can raise a transfer completion IRQ) sent during probe. Since the
OCSs of these pending requests are not SUCCESS (because they are not yet
literally finished), their UPIUs shall be dumped. When there are multiple
pending requests, the UPIU dump can be overwhelming and may lead to
stability issues because it is in atomic context. Therefore, before probe,
complete these pending requests right after host controller is stopped and
silence the UPIU dump from them.
Link: https://lore.kernel.org/r/1574751214-8321-5-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To be on the safe side, do not touch lrb after clearing its slot in the
lrb_in_use bitmap to avoid messing up the next task which would possibly
occupy this lrb.
[mkp: applied by hand]
Link: https://lore.kernel.org/r/1574751214-8321-4-git-send-email-cang@qti.qualcomm.com
Reviewed by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bkops level should be rechecked upon receiving an exception. Currently the
level is being cached and never updated.
Update bkops each time the level is checked. Also do not use the cached
bkops level value if it is disabled and then enabled.
Fixes: afdfff59a0 (scsi: ufs: handle non spec compliant bkops behaviour by device)
Link: https://lore.kernel.org/r/1574751214-8321-2-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manage TMF tags with blk_{get,put}_request() instead of
ufshcd_get_tm_free_slot() / ufshcd_put_tm_slot(). Store a per-request
completion pointer in request.end_io_data instead of using a waitqueue to
report TMF completion.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-3-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of tracking which tags are in use in the ufs_hba.lrb_in_use
bitmask, rely on the block layer tag allocation mechanism. This patch
removes the following busy-waiting loop if ufshcd_issue_devman_upiu_cmd()
and the block layer accidentally allocate the same tag for a SCSI request:
* ufshcd_queuecommand() returns SCSI_MLQUEUE_HOST_BUSY.
* The SCSI core requeues the SCSI command.
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191209181309.196233-2-bvanassche@acm.org
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During clock gating (ufshcd_gate_work()), we first put the link hibern8 by
calling ufshcd_uic_hibern8_enter() and if ufshcd_uic_hibern8_enter()
returns success (0) then we gate all the clocks. Now let’s zoom in to what
ufshcd_uic_hibern8_enter() does internally: It calls
__ufshcd_uic_hibern8_enter() and if failure is encountered, link recovery
shall put the link back to the highest HS gear and returns success (0) to
ufshcd_uic_hibern8_enter() which is the issue as link is still in active
state due to recovery! Now ufshcd_uic_hibern8_enter() returns success to
ufshcd_gate_work() and hence it goes ahead with gating the UFS clock while
link is still in active state hence I believe controller would raise UIC
error interrupts. But when we service the interrupt, clocks might have
already been disabled!
This change fixes for this by returning failure from
__ufshcd_uic_hibern8_enter() if recovery succeeds as link is still not in
hibern8, upon receiving the error ufshcd_hibern8_enter() would initiate
retry to put the link state back into hibern8.
Link: https://lore.kernel.org/r/1573798172-20534-8-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change attempts to abort gating of clocks if a request to turn-on
clocks is pending. This would in turn avoid turning OFF and back ON the
clocks.
Link: https://lore.kernel.org/r/1573798172-20534-7-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return IRQ_HANDLED only if the irq is really handled, this will help in
catching spurious interrupts that go unhandled.
Link: https://lore.kernel.org/r/1573798172-20534-6-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_print_host_regs() can be called by interrupt handler, but it may
sleep due to ufshcd_dump_regs() allocates the dump buffer memory with flag
GFP_KERNEL. Fix it by changing GFP_KERNEL to GFP_ATMOIC.
Link: https://lore.kernel.org/r/1573798172-20534-5-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up possible unclocked register access to auto hibern8 register in
resume path and through sysfs entry. Meanwhile, enable auto hibern8 only
after device is fully initialized in probe path.
Link: https://lore.kernel.org/r/1573798172-20534-4-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to recover from hibern8 exit failure, perform a reset in link
recovery path before issuing link start-up.
Link: https://lore.kernel.org/r/1573798172-20534-2-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function __ufshcd_query_descriptor(), in the event of an error
happening, we directly goto out_unlock and forget to invaliate
hba->dev_cmd.query.descriptor pointer. This results in this pointer still
valid in ufshcd_copy_query_response() for other query requests which go
through ufshcd_exec_raw_upiu_cmd(). This will cause __memcpy() crash and
system hangs. Log as shown below:
Unable to handle kernel paging request at virtual address
ffff000012233c40
Mem abort info:
ESR = 0x96000047
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000047
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp = 0000000028cc735c
[ffff000012233c40] pgd=00000000bffff003, pud=00000000bfffe003,
pmd=00000000ba8b8003, pte=0000000000000000
Internal error: Oops: 96000047 [#2] PREEMPT SMP
...
Call trace:
__memcpy+0x74/0x180
ufshcd_issue_devman_upiu_cmd+0x250/0x3c0
ufshcd_exec_raw_upiu_cmd+0xfc/0x1a8
ufs_bsg_request+0x178/0x3b0
bsg_queue_rq+0xc0/0x118
blk_mq_dispatch_rq_list+0xb0/0x538
blk_mq_sched_dispatch_requests+0x18c/0x1d8
__blk_mq_run_hw_queue+0xb4/0x118
blk_mq_run_work_fn+0x28/0x38
process_one_work+0x1ec/0x470
worker_thread+0x48/0x458
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: 540000ab a8c12027 a88120c7 a8c12027 (a88120c7)
---[ end trace 793e1eb5dff69f2d ]---
note: kworker/0:2H[2054] exited with preempt_count 1
This patch is to move "descriptor = NULL" down to below the label
"out_unlock".
Fixes: d44a5f98bb49b2(ufs: query descriptor API)
Link: https://lore.kernel.org/r/20191112223436.27449-3-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print out returned response size and buffer size, while the front one is
bigger than the back one.
Link: https://lore.kernel.org/r/20191112223436.27449-2-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declare all variables that hold dev_cmd_type values as an enum instead of
as an int.
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191029230710.211926-3-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following three kernel-doc warnings:
drivers/scsi/ufs/ufs_bsg.c:165: warning: Function parameter or member 'hba' not described in 'ufs_bsg_remove'
drivers/scsi/ufs/ufshcd.c:5789: warning: Function parameter or member 'cmd_type' not described in 'ufshcd_issue_devman_upiu_cmd'
drivers/scsi/ufs/ufshcd.c:5789: warning: Excess function parameter 'msgcode' description in 'ufshcd_issue_devman_upiu_cmd'
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20191029230710.211926-2-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no need to call ufshcd_def_desc_sizes() in ufshcd_init(), since
descriptor lengths will be checked and initialized later in
ufshcd_init_desc_sizes().
Fixes: a4b0e8a4e92b1b(scsi: ufs: Factor out ufshcd_read_desc_param)
Link: https://lore.kernel.org/r/BN7PR08MB5684A3ACE214C3D4792CE729DB610@BN7PR08MB5684.namprd08.prod.outlook.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman.wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework from previous work by:
Sujit Reddy Thumma <sthumma@codeaurora.org>
Override auto suspend tunables for UFS device LUNs during initialization so
as to efficiently manage background operations and the power consumption.
Link: https://lore.kernel.org/r/1568649411-5127-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some cases, hba may go through shutdown flow without successful
initialization and then make system hang.
For example, if ufshcd_change_power_mode() gets error and leads to
ufshcd_hba_exit() to release resources of the host, future shutdown flow
may hang the system since the host register will be accessed in unpowered
state.
To solve this issue, simply add checking to skip shutdown for above kind of
situation.
Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Use kmemdup rather than duplicating its implementation
Link: https://lore.kernel.org/r/20190831124424.18642-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS memory devices needs their reset line toggled in order to get them
into a good state for initialization. Provide a new vops to allow the
platform driver to implement this operation.
Link: https://lore.kernel.org/r/20190828191756.24312-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following BUG:
[ 187.065689] BUG: kernel NULL pointer dereference, address: 000000000000001c
[ 187.065790] RIP: 0010:ufshcd_vreg_set_hpm+0x3c/0x110 [ufshcd_core]
[ 187.065938] Call Trace:
[ 187.065959] ufshcd_resume+0x72/0x290 [ufshcd_core]
[ 187.065980] ufshcd_system_resume+0x54/0x140 [ufshcd_core]
[ 187.065993] ? pci_pm_restore+0xb0/0xb0
[ 187.066005] ufshcd_pci_resume+0x15/0x20 [ufshcd_pci]
[ 187.066017] pci_pm_thaw+0x4c/0x90
[ 187.066030] dpm_run_callback+0x5b/0x150
[ 187.066043] device_resume+0x11b/0x220
Voltage regulators are optional, so functions must check they exist
before dereferencing.
Note this issue is hidden if CONFIG_REGULATORS is not set, because the
offending code is optimised away.
Notes for stable:
The issue first appears in commit 57d104c153 ("ufs: add UFS power
management support") but is inadvertently fixed in commit 60f0187031
("scsi: ufs: disable vccq if it's not needed by UFS device") which in
turn was reverted by commit 730679817d ("Revert "scsi: ufs: disable vccq
if it's not needed by UFS device""). So fix applies v3.18 to v4.5 and
v5.1+
Fixes: 57d104c153 ("ufs: add UFS power management support")
Fixes: 730679817d ("Revert "scsi: ufs: disable vccq if it's not needed by UFS device"")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define new a type: uc_string_id for easier string handling and less
casting. Reduce number or string copies in price of a dynamic allocation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to change msleep() to usleep_range() based on
Documentation/timers/timers-howto.txt. It suggests using usleep_range()
for small msec(1ms - 20ms) since msleep() will often sleep longer than
desired value.
After changing, booting time will be 5ms-10ms faster than before. I
tested this change on two different platforms, one has 5ms faster, another
one is about 10ms. I think this is different on different platform.
Actually, from UFS host side, 1ms-5ms delay is already sufficient for its
initialization of the local UIC layer.
Fixes: 7a3e97b0dc ([SCSI] ufshcd: UFS Host controller driver)
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently only "interrupt-based" errors have their own history, however
there are some "non-interrupt-based" errors or events which need history
to improve debugging or help know the health status of UFS devices.
Example of fatal errors:
- Link startup error
- Suspend error
- Resume error
Example of abnormal events:
- Task or request abort
- Device reset (now equals to Logical Unit Reset)
- Host reset
This patch tries to track above errors and events by existed UFS error
history mechanism.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently UFS error history will be reset and lost during host reset flow
by ufschd_probe_hba().
Avoid resetting it so error history can be kept as complete as possible to
improve debugging.
In addition, fix a minor display error in ufshcd_print_err_hist().
[mkp: commit desc clarification]
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide more information about fatal and auto-hibern8 errors to improve
debugging by extending existing UFS error history framework.
[mkp: typos]
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove "uic" term in below error history functions and structures for more
general usages,
struct ufs_uic_err_reg_hist;
void ufshcd_update_uic_reg_hist(struct ufs_uic_err_reg_hist *reg_hist,
u32 reg);
void ufshcd_print_uic_err_hist(struct ufs_hba *hba,
struct ufs_uic)err_reg_hist *err_hist, char *err_name);
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
We need to also mirror the value to the device to ensure IOMMU merging
doesn't undo it, and the SCSI host level parameter will ensure that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Currently auto-hibernate is activated if host supports auto-hibern8
capability. However error-handling is not implemented, which makes the
feature somewhat risky.
If either "Hibernate Enter" or "Hibernate Exit" fail during auto-hibernate
flow, the corresponding interrupt "UIC_HIBERNATE_ENTER" or
"UIC_HIBERNATE_EXIT" shall be raised according to UFS specification.
This patch adds auto-hibernate error-handling:
- Monitor "Hibernate Enter" and "Hibernate Exit" interrupts after
auto-hibernate feature is activated.
- If a failure happens, trigger error-handling just like
"manual-hibernate" failure and apply the same recovery flow: schedule
UFS error handler in ufshcd_check_errors(), and then do host reset and
restore in UFS error handler.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendor-specific initialization flow may set its own auto-hibernate
timer. In this case, do not overwrite timer value as "default value" in
ufshcd_init().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The checking of Auto-Hibernation support is used in many places in the
driver, thus re-factor it as ufshcd_is_auto_hibern8_supported() to make
code more clean.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct ufs_dev_cmd is the main container that supports device management
commands. In the case of a read descriptor request, we assume that the
proper space was allocated in dev_cmd to hold the returning descriptor.
This is no longer true, as there are flows that doesn't use dev_cmd for
device management requests, and was wrong in the first place.
Fixes: d44a5f98bb (ufs: query descriptor API)
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If UFS device responds an unknown request response code, we can not know
what it was via logs because the code is replaced by "DID_ERROR << 16"
before log printing.
Fix this to provide precise request response code information for easier
issue breakdown.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer value is initialized as &hba->vreg_info, and it's never
changed. It's not necessary to check the pointer is null or not.
Signed-off-by: Zeng Guangyue <zengguangyue@hisilicon.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
