The transposer block is allowing one to write the result of the VC4
composition back to memory instead of displaying it on a screen.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds the missing interrupt property to the RNG block
of BCM283x.
Link: https://github.com/raspberrypi/linux/issues/2195
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
-----BEGIN PGP SIGNATURE-----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=SKgx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs devicetree changes
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
* tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Switch to port 8 for CPU port
ARM: bcm2835: Add the DPI hardware to the device tree.
ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode
ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave
ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups
ARM: dts: bcm2837-rpi-3-b: add GPIO expander
ARM: dts: bcm2835: make the firmware node into a bus
ARM: dts: bcm283x: Fix probing of bcm2835-i2s
dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s
ARM: dts: bcm283x: Fix pin function of JTAG pins
It's currently marked disabled, as it's not useful without a panel
associated with it and the GPIO pins routed to ALT2.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Since 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch define the polarity of the per-cpu interrupts on BCM2836
and BCM2837 in order to avoid the warnings from ARM arch timer code:
arch_timer: WARNING: Invalid trigger for IRQ19, assuming level low
arch_timer: WARNING: Please fix your firmware
arch_timer: cp15 timer(s) running at 19.20MHz (virt).
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes the DTC warnings about missing property #phy-cells.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Contrary to other RPi devices, RPi3 uses uart0 to communicate with
the BCM43438 bluetooth controller. uart1 is then used for the console.
Today, the console configuration is inherited from the bcm283x dtsi
(bootargs) which is not the correct one for the RPi3. This leads to
routing issue and confuses the Bluetooth controller with unexpected
data.
This patch introduces chosen/stdout path to configure console to uart0
on bcm283x family and overwrite it to uart1 in the RPi3 dts.
Create serial0/1 aliases referring to uart0 and uart1 paths.
Remove unneeded earlyprintk.
Fixes: 4188ea2aeb ("ARM: bcm283x: Define UART pinmuxing on board level")
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device
support for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H
with 10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module
plus board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600
and the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation
of the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards
are added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC platforms
from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much
more useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=onXv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device support
for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H with
10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module plus
board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600 and
the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation of
the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards are
added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC
platforms from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much more
useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (345 commits)
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
ARM: pxa: Use - instead of @ for DT OPP entries
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
...
In order to use dwc2 in OTG or gadget mode the USB PHY should be
specified. Since there is no bcm283x USB PHY driver use the generic
one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document uart1 doesn't map to pins
36-39, but uart0 does.
Also, split into separate Rx/Tx and CST/RTS groups to match other uart nodes.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document i2c0 doesn't map to pins 32,
34 but to 28, 29.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
Downstream kernel uses pins 32, 33 as UART0 (PL011) Rx/Tx to communicate with
the Bluetooth chip. So ALT3 of these pins is most likely not CTS/RTS. Change
the node name to reflect that. This matches section 6.2 "Alternative Function
Assignments" in the BCM2835 ARM Peripherals document.
With this change in place, adding
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
to bcm2837-rpi-3-b.dts does the right thing on my Raspberry Pi 3.
Pins 30, 31 are CTS/RTS of UART0 in alternate function 3. Rename uart0_gpio30
as well.
While at it, fix a little typo in a nearby comment.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
Add the dmas and dma-names properties to support HDMI audio.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the VEC (Video EnCoder) node definition in bcm283x.dtsi.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the node for the thermal sensor of the bcm2835-soc
to the device tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Changelog:
V1 -> V5: generic settings is shared in bcm283x.dtsi, but disabled
moved the compatible string to the SOC specific dtsi
for arm and arm64
V5 -> V6: fix remove 0x prefix from thermal@0x7e212000
Note: there is no arm/boot/dts/bcm2837.dtsi as of now,
so the 32-bit rpi3 dt is not modified.
Signed-off-by: Eric Anholt <eric@anholt.net>
The address of the mailbox node in the bcm283x.dtsi also has a typo.
So fix it accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Fixes: 05b682b7a3 ("ARM: bcm2835: dt: Add the mailbox to the device tree")
Signed-off-by: Eric Anholt <eric@anholt.net>
The BCM2835-ARM-Peripherals.pdf documentation specifies what the
function selects do for the pins, and there are a bunch of obvious
groupings to be made. With these created, we'll be able to replace
bcm2835-rpi.dtsi's main "set all of these pins to alt0" with
references to specific groups we want enabled.
Also add pinctrl groups for emmc and sdhost.
Based on patches by Eric Anholt, with fixups by Gerd Hoffmann.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably,
an ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets;
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E,
Orange Pi Lite, Olimex A33-Olinuxino, and Nano Pi Neo
single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform;
Raspberry Pi Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file);
Armada 395 SoC platform and GP board
Armada 390 DB development board
- NXP i.MX: imx7s Warp7 reference board;
Gateworks Ventana GW553x single-board computer,
Technologic Systems TS-4900 and
Engicam IMX6UL GEA M6UL computer-on-module,
Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board;
Firefly RK3288 Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer
Conflicts: vendor-prefixes.txt has conflicting additions, keep all of
them in alphabetical order.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/gg/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
This file is included from DTS files under arch/arm64 too (via
broadcom/bcm2837-rpi-3-b.dts and broadcom/bcm2837.dtsi). There is a desire
not to have skeleton.dtsi for ARM64. See commit 3ebee5a2e1 ("arm64: dts:
kill skeleton.dtsi") for rationale for its removal.
As well as the addition of #*-cells also requires adding the device_type to
the rpi memory node explicitly.
Note that this change results in the removal of an empty /aliases node from
bcm2835-rpi-a.dtb and bcm2835-rpi-a-plus.dtb. I have no hardware to check
if this is a problem or not.
It also results in some reordering of the nodes in the DTBs (the /aliases
and /memory nodes come later). This isn't supposed to matter but, again,
I've no hardware to check if it is true in this particular case.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: arm@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to the DWC2 binding an appropriate clock is required.
This clock isn't handled by bcm2835 clock driver, so add a fixed
clock to the bcm283x DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The hub and the ethernet in its port 1 are hardwired on the board.
Compared to the adapters that can be plugged into the USB ports, this
one has no serial EEPROM to store its MAC. Nevertheless, the Raspberry Pi
has the MAC address for this adapter in its ROM, accessible from its
firmware.
U-Boot can read out the address and set the local-mac-address property of the
node with "ethernet" alias. Let's add the node so that U-Boot can do its
business.
Model B rev2 and Model B+ entries were verified by me, the hierarchy and
pid/vid pair for the Version 2 was provided by Peter Chen. Original
Model B is a blind shot, though very likely correct.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Add interrupt-names properties to dt and apply the correct
mapping between irq and dma channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This connects the USB driver to the USB power domain, so that USB can
actually be turned on at boot if the bootloader didn't do it for us.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
This patch fixes the naming of the device tree node: uart@7e201000
to conform to the standard of: serial@7e201000
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables the use of the auxiliary spi1 and spi2 devices
on the bcm2835 SOC.
Note that this requires the use of the new clk-bcm2835-aux to work.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
The set of peripherals remained constant across bcm2835 (Raspberry Pi
1) and bcm2836 (Raspberry Pi 2), but the CPU was swapped out. Split
the files so that we can include just peripheral setup in 2836.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
