This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:
* If there was a frequency transition before, the multiplier read from the
register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
register always reads as zero, regardless of the current multiplier that
is set using switches on the mainboard and that the CPU is running at.
The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.
For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.
There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.
During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.
This patch flushes the cache during frequency transition. It fixes the
instability.
Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
open during other activity (running other kernel code with the port open
shouldn't cause any misbehavior, but we should better be safe and keep
the port closed)
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make the driver multiplatform-friendly, unconditional initialization
in an initcall is replaced with a platform driver probed only if
respective platform device is registered.
Tested at: Exynos4210 (TRATS) and Exynos4412 (TRATS2)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.
Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).
In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.
It's been tested on iMX6SL board where the platform doesn't have
an OPP table.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The imx6q-cpufreq driver nowadays is not only running on imx6q but also
other i.MX6 series SoCs like imx6dl and imx6sl. Update Kconfig prompt
and help text to make it clear to users.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
on i.MX6Q, cpu freq change need to follow below flows:
1. each setpoint has different VDDARM, VDDSOC/PU voltage, get the setpoint
table from dts;
2. when cpu freq is scaling up, need to increase VDDSOC/PU voltage before
VDDARM, if VDDPU is off, no need to change it;
3. when cpu freq is scaling down, need to decrease VDDARM voltage before
VDDSOC/PU, if VDDPU is off, no need to change it;
normally dts will pass vddsoc/pu freq/volt info to kernel, if not, will
use fixed value for vddsoc/pu voltage setting.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the current code, if we fail during a frequency transition, we
simply send the POSTCHANGE notification with the old frequency. This
isn't enough.
One of the core users of these notifications is the code responsible
for keeping loops_per_jiffy aligned with frequency changes. And mostly
it is written as:
if ((val == CPUFREQ_PRECHANGE && freq->old < freq->new) ||
(val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
update-loops-per-jiffy...
}
So, suppose we are changing to a higher frequency and failed during
transition, then following will happen:
- CPUFREQ_PRECHANGE notification with freq-new > freq-old
- CPUFREQ_POSTCHANGE notification with freq-new == freq-old
The first one will update loops_per_jiffy and second one will do
nothing. Even if we send the 2nd notification by exchanging values of
freq-new and old, some users of these notifications might get
unstable.
This can be fixed by simply calling cpufreq_notify_post_transition()
with error code and this routine will take care of sending
notifications in the correct order.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Folded 3 patches into one, rebased unicore2 changes]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use common clock framework (CCF) APIs to set the clock rates
instead of direct register manipulation. This now updates the
sysfs entry (cpuinfo_cur_freq) correctly which did not reflect
the correct value until now. While at it clean up the PLL s-div
parameter setting as it is handled by the PLL driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a CPU is hot removed we'll cancel all the delayed work items via
gov_cancel_work(). Sometimes the delayed work function determines that
it should adjust the delay for all other CPUs that the policy is
managing. If this scenario occurs, the canceling CPU will cancel its own
work but queue up the other CPUs works to run.
Commit 3617f2 (cpufreq: Fix timer/workqueue corruption due to double
queueing) has tried to fix this, but reading governor_enabled is not
protected by cpufreq_governor_lock. Even though od_dbs_timer() checks
governor_enabled before gov_queue_work(), this scenario may occur. For
example:
CPU0 CPU1
---- ----
cpu_down()
... <work runs>
__cpufreq_remove_dev() od_dbs_timer()
__cpufreq_governor() policy->governor_enabled
policy->governor_enabled = false;
cpufreq_governor_dbs()
case CPUFREQ_GOV_STOP:
gov_cancel_work(dbs_data, policy);
cpu0 work is canceled
timer is canceled
cpu1 work is canceled
<waits for cpu1>
gov_queue_work(*, *, true);
cpu0 work queued
cpu1 work queued
cpu2 work queued
...
cpu1 work is canceled
cpu2 work is canceled
...
At the end of the GOV_STOP case cpu0 still has a work queued to
run although the code is expecting all of the works to be
canceled. __cpufreq_remove_dev() will then proceed to
re-initialize all the other CPUs works except for the CPU that is
going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs()
will trample over the queued work and debugobjects will spit out
a warning:
WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc()
ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x14
Modules linked in:
CPU: 1 PID: 1205 Comm: sh Tainted: G W 3.10.0 #200
[<c01144f0>] (unwind_backtrace+0x0/0xf8) from [<c0111d98>] (show_stack+0x10/0x14)
[<c0111d98>] (show_stack+0x10/0x14) from [<c01272cc>] (warn_slowpath_common+0x4c/0x68)
[<c01272cc>] (warn_slowpath_common+0x4c/0x68) from [<c012737c>] (warn_slowpath_fmt+0x30/0x40)
[<c012737c>] (warn_slowpath_fmt+0x30/0x40) from [<c034c640>] (debug_print_object+0x94/0xbc)
[<c034c640>] (debug_print_object+0x94/0xbc) from [<c034c7f8>] (__debug_object_init+0xc8/0x3c0)
[<c034c7f8>] (__debug_object_init+0xc8/0x3c0) from [<c01360e0>] (init_timer_key+0x20/0x104)
[<c01360e0>] (init_timer_key+0x20/0x104) from [<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c)
[<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c) from [<c04833a8>] (__cpufreq_governor+0x80/0x1b0)
[<c04833a8>] (__cpufreq_governor+0x80/0x1b0) from [<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380)
[<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380) from [<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c)
[<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c) from [<c014fb40>] (notifier_call_chain+0x44/0x84)
[<c014fb40>] (notifier_call_chain+0x44/0x84) from [<c012ae44>] (__cpu_notify+0x2c/0x48)
[<c012ae44>] (__cpu_notify+0x2c/0x48) from [<c068dd40>] (_cpu_down+0x80/0x258)
[<c068dd40>] (_cpu_down+0x80/0x258) from [<c068df40>] (cpu_down+0x28/0x3c)
[<c068df40>] (cpu_down+0x28/0x3c) from [<c068e4c0>] (store_online+0x30/0x74)
[<c068e4c0>] (store_online+0x30/0x74) from [<c03a7308>] (dev_attr_store+0x18/0x24)
[<c03a7308>] (dev_attr_store+0x18/0x24) from [<c0256fe0>] (sysfs_write_file+0x100/0x180)
[<c0256fe0>] (sysfs_write_file+0x100/0x180) from [<c01fec9c>] (vfs_write+0xbc/0x184)
[<c01fec9c>] (vfs_write+0xbc/0x184) from [<c01ff034>] (SyS_write+0x40/0x68)
[<c01ff034>] (SyS_write+0x40/0x68) from [<c010e200>] (ret_fast_syscall+0x0/0x48)
In gov_queue_work(), lock cpufreq_governor_lock before gov_queue_work,
and unlock it after __gov_queue_work(). In this way, governor_enabled
is guaranteed not changed in gov_queue_work().
Signed-off-by: Jane Li <jiel@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Local variable used only in this file is made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The arm_big_little cpufreq driver is only used by ARM bigLITTLE
platforms and hence must depend on CONFIG_BIG_LITTLE.
This was highlighted by Russell earlier when he reported this issue:
drivers/built-in.o: In function `bL_cpufreq_set_rate':
powercap_sys.c:(.text+0x5ed9a0): undefined reference to `bL_switch_request_cb'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prevent __cpufreq_add_dev() from overwriting the existing values of
user_policy.{min|max|policy|governor} with defaults during resume
from system suspend.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If cpufreq_policy_restore() returns NULL during system resume,
__cpufreq_add_dev() should just fall back to the full initialization
instead of returning an error, because that may actually make things
work. Moreover, it should not leave stale fallback data behind after
it has failed to restore a previously existing policy.
This change is based on Viresh Kumar's work.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
PM_OPP is a helper library used by several of the existing cpufreq drivers.
Some of the drivers select this symbol while others depend on it and rely
on the architecture to enable it. Make this behaviour more consistent and
obvious by having all the drivers select the symbol. This will also allow
better build coverage of the affected drivers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The patch currently under review to enable ARM cpufreq drivers for ARM64
which is useful due to the large amount of shared IP between ARM and ARM64
SoCs. However the big.LITTLE switcher relies on an architecture interface
to build which is not present on ARM64. Add a dependency until that is
resolved.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the periodic P state boost. This code required for some corner
case benchmark tests. The calculation of the required P state was
incorrect/inaccurate and would not allow P state increase.
This was fixed by a combination of commits:
2134ed4 cpufreq / intel_pstate: Change to scale off of max P-state
d253d2a intel_pstate: Improve accuracy by not truncating until final result
References: https://bugzilla.kernel.org/show_bug.cgi?id=64271
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Baytrail requires setting P state and voltage pairs when adjusting the
requested P state. Add function for retrieving the valid voltage
values and modify *_set_pstate() functions to caluclate the
appropriate voltage for the requested P state.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When configuring a default governor (via CONFIG_CPU_FREQ_DEFAULT_*) with the
intel_pstate driver, the desired default policy is not properly set. For
example, setting 'CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE' ends up with the
'powersave' policy being set.
Fix by configuring the correct default policy, if either 'powersave' or
'performance' are requested. Otherwise, fallback to what the driver originally
set via its 'init' routine.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are cases where cpufreq_add_dev() may fail for some CPUs
during system resume. With the current code we will still have
sysfs cpufreq files for those CPUs and struct cpufreq_policy
would be already freed for them. Hence any operation on those
sysfs files would result in kernel warnings.
Example of problems resulting from resume errors (from Bjørn Mork):
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
To fix this, remove those sysfs files or put the associated kobject
in case of such errors. Also, to make it simple, remove the cpufreq
sysfs links from all the CPUs (except for the policy->cpu) during
suspend, as that operation won't result in a loss of sysfs file
permissions and we can create those links during resume just fine.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function at32_cpufreq_driver_init was marked as __init but will be
called from inside the cpufreq framework. This lead to the following a
section mismatch during compilation:
WARNING: drivers/built-in.o(.data+0x2448): Section mismatch in reference
from the variable at32_driver to the function
.init.text:at32_cpufreq_driver_init()
The variable at32_driver references
the function __init at32_cpufreq_driver_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Commit 2167e2399d (cpufreq: fix garbage kobjects on errors during
suspend/resume) breaks suspend/resume on Martin Ziegler's system
(hard lockup during resume), so revert it.
Fixes: 2167e2399d (cpufreq: fix garbage kobjects on errors during suspend/resume)
References: https://bugzilla.kernel.org/show_bug.cgi?id=66751
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5a87182aa2 (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa2 (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Treat both negative and zero return values from clk_round_rate()
as errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather
than a signed type, since some clock sources can generate rates
higher than (2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of
zero will be considered a error. All other values will be
considered valid rates. The comparison against values less than
0 is kept to preserve the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Treat both negative and zero return values from clk_round_rate()
as errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather
than a signed type, since some clock sources can generate rates
higher than (2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of
zero will be considered a error. All other values will be
considered valid rates. The comparison against values less than
0 is kept to preserve the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
This is effectively a revert of commit 5302c3fb2e ("cpufreq: Perform
light-weight init/teardown during suspend/resume"), which enabled
suspend/resume optimizations leaving the sysfs files in place.
Errors during suspend/resume are not handled properly, leaving
dead sysfs attributes in case of failures. There are are number of
functions with special code for the "frozen" case, and all these
need to also have special error handling.
The problem is easy to demonstrate by making cpufreq_driver->init()
or cpufreq_driver->get() fail during resume.
The code is too complex for a simple fix, with split code paths
in multiple blocks within a number of functions. It is therefore
best to revert the patch enabling this code until the error handling
is in place.
Examples of problems resulting from resume errors:
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
The failure to restore cpufreq devices on cancelled hibernation is
not a new bug. It is caused by the ACPI _PPC call failing unless the
hibernate is completed. This makes the acpi_cpufreq driver fail its
init.
Previously, the cpufreq device could be restored by offlining the
cpu temporarily. And as a complete hibernation cycle would do this,
it would be automatically restored most of the time. But after
commit 5302c3fb2e the leftover sysfs attributes will block any
device add action. Therefore offlining and onlining CPU 1 will no
longer restore the cpufreq object, and a complete suspend/resume
cycle will replace it with garbage.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}_noirq()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found anr issue where
tunables configuration for clusters/sockets with non-boot CPUs was
getting lost after suspend/resume, as we were notifying governors
with CPUFREQ_GOV_POLICY_EXIT on removal of the last cpu for that
policy and so deallocating memory for tunables. This is fixed by
this patch as we don't allow any operation on governors after
device suspend and before device resume now.
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog, minor cleanups]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The init functions are linked statically (no support for
dynamic loading) and have no other users. Hence remove
EXPORT_SYMBOL for these functions.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
d4019f0a92 "cpufreq: move freq change notifications to cpufreq core"
added code to the cpufreq core to print an error if a cpufreq driver's
.target() function returned an error. This exposed the fact that Tegra's
cpufreq driver returns an error when it is ignoring requests due to the
system being suspended.
Modify Tegra's .target() function not to return an error in this case;
this prevents the error prints. The argument is that since the suspend
hook can't and doesn't inform the cpufreq core when its requests will
be ignored, there's no way for the cpufreq core to squelch them, so it's
not an error for the requests to keep coming. This change make the Tegra
driver consistent with how the Exynos handles the same situation. Note
that s5pv210-cpufreq.c probably suffers from this same issue though.
Fixes: d4019f0a92 (cpufreq: move freq change notifications to cpufreq core)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
* pm-cpufreq:
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
cpufreq: conservative: set requested_freq to policy max when it is over policy max
The related code has been changed and the comment is out of date.
So remove it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
With a recent change "d4019f0 cpufreq: move freq change notifications to cpufreq
core" few variables (r & ret) are removed by mistake and hence these warnings:
drivers/cpufreq/omap-cpufreq.c: In function omap_target:
drivers/cpufreq/omap-cpufreq.c:64:2: error: ret undeclared (first use in this function)
drivers/cpufreq/omap-cpufreq.c:64:2: note: each undeclared identifier is reported only once for each function it appears in
drivers/cpufreq/omap-cpufreq.c:94:3: error: r undeclared (first use in this function)
drivers/cpufreq/omap-cpufreq.c:116:1: warning: control reaches end of non-void function [-Wreturn-type]
Lets fix them by declaring those variables again.
Fixes: d4019f0a92 (cpufreq: move freq change notifications to cpufreq core)
Reported-by: Sebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When requested_freq is over policy->max, set it to policy->max.
This can help to speed up decreasing frequency.
Signed-off-by: Xiaoguang Chen <chenxg@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
When decreasing frequency, requested_freq may be less than
freq_target, So requested_freq minus freq_target may be negative,
But reqested_freq's unit is unsigned int, then the negative result
will be one larger interger which may be even higher than
requested_freq.
This patch is to fix such issue. when result becomes negative,
set requested_freq as the min value of policy.
Signed-off-by: Xiaoguang Chen <chenxg@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
intel_pstate: skip the driver if ACPI has power mgmt option
cpufreq: ondemand: Remove redundant return statement
cpufreq: move freq change notifications to cpufreq core
cpufreq: distinguish drivers that do asynchronous notifications
cpufreq/intel_pstate: Add static declarations to internal functions
cpufreq: arm_big_little: reconfigure switcher behavior at run time
cpufreq: arm_big_little: add in-kernel switching (IKS) support
ARM: vexpress/TC2: register vexpress-spc cpufreq device
cpufreq: arm_big_little: add vexpress SPC interface driver
ARM: vexpress/TC2: add cpu clock support
ARM: vexpress/TC2: add support for CPU DVFS
