This patch is to support hardware timestamp conversion to
PHC bound. This applies to both RX and TX since their skb
handling (for TX, it's skb clone in error queue) all goes
through __sock_recv_timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since PTP virtual clock support is added, there can be
several PTP virtual clocks based on one PTP physical
clock for timestamping.
This patch is to extend SO_TIMESTAMPING API to support
PHC (PTP Hardware Clock) binding by adding a new flag
SOF_TIMESTAMPING_BIND_PHC. When PTP virtual clocks are
in use, user space can configure to bind one for
timestamping, but PTP physical clock is not supported
and not needed to bind.
This patch is preparation for timestamp conversion from
raw timestamp to a specific PTP virtual clock time in
core net.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split timestamping handling into a new function
mptcp_setsockopt_sol_socket_timestamping().
This is preparation for extending SO_TIMESTAMPING
for PHC binding, since optval will no longer be
integer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for getting PHC (PTP Hardware Clock)
virtual clocks, which are based on PHC physical clock
providing hardware timestamp to network packets.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The doc draft-stewart-tsvwg-sctp-ipv4-00 that restricts 198 addresses
was never published. These addresses as private addresses should be
allowed to use in SCTP.
As Michael Tuexen suggested, this patch is to move 198 addresses from
unusable to private scope.
Reported-by: Sérgio <surkamp@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Marcelo's suggestion this will make code more clear to read.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core has a layered structure, and even though we end up
returning 0 (success) to user space when setting a bonding/team upper
that can't be offloaded, some parts of the framework actually need to
know that we couldn't offload that.
For example, if dsa_switch_lag_join returns 0 as it currently does,
dsa_port_lag_join has no way to tell a successful offload from a
software fallback, and it will call dsa_port_bridge_join afterwards.
Then we'll think we're offloading the bridge master of the LAG, when in
fact we're not even offloading the LAG. In turn, this will make us set
skb->offload_fwd_mark = true, which is incorrect and the bridge doesn't
like it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_ll_usec is read locklessly from sk_can_busy_loop()
while another thread can change its value in sock_setsockopt()
This is correct but needs annotations.
BUG: KCSAN: data-race in __skb_try_recv_datagram / sock_setsockopt
write to 0xffff88814eb5f904 of 4 bytes by task 14011 on cpu 0:
sock_setsockopt+0x1287/0x2090 net/core/sock.c:1175
__sys_setsockopt+0x14f/0x200 net/socket.c:2100
__do_sys_setsockopt net/socket.c:2115 [inline]
__se_sys_setsockopt net/socket.c:2112 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2112
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88814eb5f904 of 4 bytes by task 14001 on cpu 1:
sk_can_busy_loop include/net/busy_poll.h:41 [inline]
__skb_try_recv_datagram+0x14f/0x320 net/core/datagram.c:273
unix_dgram_recvmsg+0x14c/0x870 net/unix/af_unix.c:2101
unix_seqpacket_recvmsg+0x5a/0x70 net/unix/af_unix.c:2067
____sys_recvmsg+0x15d/0x310 include/linux/uio.h:244
___sys_recvmsg net/socket.c:2598 [inline]
do_recvmmsg+0x35c/0x9f0 net/socket.c:2692
__sys_recvmmsg net/socket.c:2771 [inline]
__do_sys_recvmmsg net/socket.c:2794 [inline]
__se_sys_recvmmsg net/socket.c:2787 [inline]
__x64_sys_recvmmsg+0xcf/0x150 net/socket.c:2787
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x00000101
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14001 Comm: syz-executor.3 Not tainted 5.13.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hbinfo" struct has a 4 byte hole at the end so we have to zero it
out to prevent stack information from being disclosed.
Fixes: fe59379b9a ("sctp: do the basic send and recv for PLPMTUD probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implement when comparing two flow keys, we will return
result after comparing the whole key from start to end.
In our optimization, we will return result in the first none-zero
comparison, then we will improve the flow table looking up efficiency.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener
to another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance
(for pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require
jump labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast address
allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks
in NAPI context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and NXP
(our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm 60GHz WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LvtX
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
-----BEGIN PGP SIGNATURE-----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=tmak
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull SELinux updates from Paul Moore:
- The slow_avc_audit() function is now non-blocking so we can remove
the AVC_NONBLOCKING tricks; this also includes the 'flags' variant of
avc_has_perm().
- Use kmemdup() instead of kcalloc()+copy when copying parts of the
SELinux policydb.
- The InfiniBand device name is now passed by reference when possible
in the SELinux code, removing a strncpy().
- Minor cleanups including: constification of avtab function args,
removal of useless LSM/XFRM function args, SELinux kdoc fixes, and
removal of redundant assignments.
* tag 'selinux-pr-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: kill 'flags' argument in avc_has_perm_flags() and avc_audit()
selinux: slow_avc_audit has become non-blocking
selinux: Fix kernel-doc
selinux: use __GFP_NOWARN with GFP_NOWAIT in the AVC
lsm_audit,selinux: pass IB device name by reference
selinux: Remove redundant assignment to rc
selinux: Corrected comment to match kernel-doc comment
selinux: delete selinux_xfrm_policy_lookup() useless argument
selinux: constify some avtab function arguments
selinux: simplify duplicate_policydb_cond_list() by using kmemdup()
Merge misc updates from Andrew Morton:
"191 patches.
Subsystems affected by this patch series: kthread, ia64, scripts,
ntfs, squashfs, ocfs2, kernel/watchdog, and mm (gup, pagealloc, slab,
slub, kmemleak, dax, debug, pagecache, gup, swap, memcg, pagemap,
mprotect, bootmem, dma, tracing, vmalloc, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (191 commits)
mm,hwpoison: make get_hwpoison_page() call get_any_page()
mm,hwpoison: send SIGBUS with error virutal address
mm/page_alloc: split pcp->high across all online CPUs for cpuless nodes
mm/page_alloc: allow high-order pages to be stored on the per-cpu lists
mm: replace CONFIG_FLAT_NODE_MEM_MAP with CONFIG_FLATMEM
mm: replace CONFIG_NEED_MULTIPLE_NODES with CONFIG_NUMA
docs: remove description of DISCONTIGMEM
arch, mm: remove stale mentions of DISCONIGMEM
mm: remove CONFIG_DISCONTIGMEM
m68k: remove support for DISCONTIGMEM
arc: remove support for DISCONTIGMEM
arc: update comment about HIGHMEM implementation
alpha: remove DISCONTIGMEM and NUMA
mm/page_alloc: move free_the_page
mm/page_alloc: fix counting of managed_pages
mm/page_alloc: improve memmap_pages dbg msg
mm: drop SECTION_SHIFT in code comments
mm/page_alloc: introduce vm.percpu_pagelist_high_fraction
mm/page_alloc: limit the number of pages on PCP lists when reclaim is active
mm/page_alloc: scale the number of pages that are batch freed
...
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Compiler can perform the sanity check instead of waiting
to load the module and crash the host.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"Static" is a loaded word, and probably not what the author meant when
the code was written.
In particular, this looks weird:
$ bridge fdb add dev swp0 00:01:02:03:04:05 local # totally fine, but
$ bridge fdb add dev swp0 00:01:02:03:04:05 static
[ 2020.708298] swp0: FDB only supports static addresses # hmm what?
By looking at the implementation which uses dev_uc_add/dev_uc_del it is
absolutely clear that only local addresses are supported, and the proper
Network Unreachability Detection state is being used for this purpose
(user space indeed sets NUD_PERMANENT when local addresses are meant).
So it is just the message that is wrong, fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more modern printk helper for network interfaces, which also
contains information about the associated struct device, and results in
overall shorter line lengths compared to printing an open-coded
dev->name.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add tracers to trace inet socket errors only. A user
space monitor application can track connection errors indepedent from
socket lifetime and do additional handling. For example a cluster
manager can fence a node if errors occurs in a specific heuristic.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a function wrapper to call the sk_error_report
callback. That will prepare to add additional handling whenever
sk_error_report is called, for example to trace socket errors.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmDa/58THHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXufBB/sGVIp1OhrtRFXeLJGJtbPPJzbh1w+K
hlDxthpN8uW7W7jyQRShiNUVwGX1QUiKBUH5g9oVKYBm0/srup4TivT2PiXPp4mC
7rPM9jcOD0ei9W2Z1/fjQvyorz37pQzq9GMF37FGqPM2mVuCl16QhdF5EqYjipCU
k34MyvjUPudmYot3gdiURyxrUljzw3KLfVXeg1Tpk0mXLZvm6OnyRn9ywgNJb+Pz
wn2+Om3hZCtccF2CUUS1LbMPFF97xy/CdAObyDuJyyXfyY7JFZ/guWBkQpi0tejQ
/+yJFYYZSo1lXV8xxB0t8LR9Vf6OxZNexn+0El4IUO4TZuAJcr4Q6fYp
=yOAz
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
"Just a few minor enhancement patches and bug fixes"
* tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
PCI: hv: Add check for hyperv_initialized in init_hv_pci_drv()
Drivers: hv: Move Hyper-V extended capability check to arch neutral code
drivers: hv: Fix missing error code in vmbus_connect()
x86/hyperv: fix logical processor creation
hv_utils: Fix passing zero to 'PTR_ERR' warning
scsi: storvsc: Use blk_mq_unique_tag() to generate requestIDs
Drivers: hv: vmbus: Copy packets sent by Hyper-V out of the ring buffer
hv_balloon: Remove redundant assignment to region_start
Use vma_lookup() to find the VMA at a specific address. As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.
Link: https://lkml.kernel.org/r/20210521174745.2219620-13-Liam.Howlett@Oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: David Miller <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we join a bridge that already has some local addresses pointing to
itself, we do not get those notifications. Similarly, when we leave that
bridge, we do not get notifications for the deletion of those entries.
The only switchdev notifications we get are those of entries added while
the DSA port is enslaved to the bridge.
This makes use cases such as the following work properly (with the
number of additions and removals properly balanced):
ip link add br0 type bridge
ip link add br1 type bridge
ip link set br0 address 00:01:02:03:04:05
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 up
ip link set swp1 up
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 up
ip link set br1 up
ip link del br1 # 00:01:02:03:04:05 still installed on the CPU port
ip link del br0 # 00:01:02:03:04:05 finally removed from the CPU port
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
(a) "dev" is a bridge port which the DSA switch tree offloads, but is
otherwise not a dsa slave (such as a LAG netdev), or
(b) "dev" is the bridge net device itself
then strange things happen to the dev_hold/dev_put pair:
dsa_schedule_work() will still be called with a DSA port that offloads
that netdev, but dev_hold() will be called on the non-DSA netdev.
Then the "if" condition in dsa_slave_switchdev_event_work() does not
pass, because "dev" is not a DSA netdev, so dev_put() is not called.
This results in the simple fact that we have a reference counting
mismatch on the "dev" net device.
This can be seen when we add support for host addresses installed on the
bridge net device.
ip link add br1 type bridge
ip link set br1 address 00:01:02:03:04:05
ip link set swp0 master br1
ip link del br1
[ 968.512278] unregister_netdevice: waiting for br1 to become free. Usage count = 5
It seems foolish to do penny pinching and not add the net_device pointer
in the dsa_switchdev_event_work structure, so let's finally do that.
As an added bonus, when we start offloading local entries pointing
towards the bridge, these will now properly appear as 'offloaded' in
'bridge fdb' (this was not possible before, because 'dev' was assumed to
only be a DSA net device):
00:01:02:03:04:05 dev br0 vlan 1 offload master br0 permanent
00:01:02:03:04:05 dev br0 offload master br0 permanent
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge supports a legacy way of adding local (non-forwarded) FDB
entries, which works on an individual port basis:
bridge fdb add dev swp0 00:01:02:03:04:05 master local
As well as a new way, added by Roopa Prabhu in commit 3741873b4f
("bridge: allow adding of fdb entries pointing to the bridge device"):
bridge fdb add dev br0 00:01:02:03:04:05 self local
The two commands are functionally equivalent, except that the first one
produces an entry with fdb->dst == swp0, and the other an entry with
fdb->dst == NULL. The confusing part, though, is that even if fdb->dst
is swp0 for the 'local on port' entry, that destination is not used.
Nonetheless, the idea is that the bridge has reference counting for
local entries, and local entries pointing towards the bridge are still
'as local' as local entries for a port.
The bridge adds the MAC addresses of the interfaces automatically as
FDB entries with is_local=1. For the MAC address of the ports, fdb->dst
will be equal to the port, and for the MAC address of the bridge,
fdb->dst will point towards the bridge (i.e. be NULL). Therefore, if the
MAC address of the bridge is not inherited from either of the physical
ports, then we must explicitly catch local FDB entries emitted towards
the br0, otherwise we'll miss the MAC address of the bridge (and, of
course, any entry with 'bridge add dev br0 ... self local').
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge automatically creates local (not forwarded) fdb entries
pointing towards physical ports with their interface MAC addresses.
For switchdev, the significance of these fdb entries is the exact
opposite of that of non-local entries: instead of sending these frame
outwards, we must send them inwards (towards the host).
NOTE: The bridge's own MAC address is also "local". If that address is
not shared with any port, the bridge's MAC is not be added by this
functionality - but the following commit takes care of that case.
NOTE 2: We mark these addresses as host-filtered regardless of the value
of ds->assisted_learning_on_cpu_port. This is because, as opposed to the
speculative logic done for dynamic address learning on foreign
interfaces, the local FDB entries are rather fixed, so there isn't any
risk of them migrating from one bridge port to another.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is able to install FDB entries towards the CPU port for addresses
which were dynamically learnt by the software bridge on foreign
interfaces that are in the same bridge with a DSA switch interface.
Since this behavior is opportunistic, it is guarded by the
"assisted_learning_on_cpu_port" property which can be enabled by drivers
and is not done automatically (since certain switches may support
address learning of packets coming from the CPU port).
But if those FDB entries added on the foreign interfaces are static
(added by the user) instead of dynamically learnt, currently DSA does
not do anything (and arguably it should).
Because static FDB entries are not supposed to move on their own, there
is no downside in reusing the "assisted_learning_on_cpu_port" logic to
sync static FDB entries to the DSA CPU port unconditionally, even if
assisted_learning_on_cpu_port is not requested by the driver.
For example, this situation:
br0
/ \
swp0 dummy0
$ bridge fdb add 02:00:de:ad:00:01 dev dummy0 vlan 1 master static
Results in DSA adding an entry in the hardware FDB, pointing this
address towards the CPU port.
The same is true for entries added to the bridge itself, e.g:
$ bridge fdb add 02:00:de:ad:00:01 dev br0 vlan 1 self local
(except that right now, DSA still ignores 'local' FDB entries, this will
be changed in a later patch)
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DSA master implements strict address filtering, then the unicast
and multicast addresses kept by the DSA CPU ports should be synchronized
with the address lists of the DSA master.
Note that we want the synchronization of the master's address lists even
if the DSA switch doesn't support unicast/multicast database operations,
on the premises that the packets will be flooded to the CPU in that
case, and we should still instruct the master to receive them. This is
why we do the dev_uc_add() etc first, even if dsa_port_notify() returns
-EOPNOTSUPP. In turn, dev_uc_add() and friends return error only if
memory allocation fails, so it is probably ok to check and propagate
that error code and not just ignore it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same concerns expressed for host MDB entries are valid for host FDBs
just as well:
- in the case of multiple bridges spanning the same switch chip, deleting
a host FDB entry that belongs to one bridge will result in breakage to
the other bridge
- not deleting FDB entries across DSA links means that the switch's
hardware tables will eventually run out, given enough wear&tear
So do the same thing and introduce reference counting for CPU ports and
DSA links using the same data structures as we have for MDB entries.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA treats some bridge FDB entries by trapping them to the CPU port.
Currently, the only class of such entries are FDB addresses learnt by
the software bridge on a foreign interface. However there are many more
to be added:
- FDB entries with the is_local flag (for termination) added by the
bridge on the user ports (typically containing the MAC address of the
bridge port)
- FDB entries pointing towards the bridge net device (for termination).
Typically these contain the MAC address of the bridge net device.
- Static FDB entries installed on a foreign interface that is in the
same bridge with a DSA user port.
The reason why a separate cross-chip notifier for host FDBs is justified
compared to normal FDBs is the same as in the case of host MDBs: the
cross-chip notifier matching function in switch.c should avoid
installing these entries on routing ports that route towards the
targeted switch, but not towards the CPU. This is required in order to
have proper support for H-like multi-chip topologies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since the cross-chip notifiers were introduced, the design was
meant to be simplistic and just get the job done without worrying too
much about dangling resources left behind.
For example, somebody installs an MDB entry on sw0p0 in this daisy chain
topology. It gets installed using ds->ops->port_mdb_add() on sw0p0,
sw1p4 and sw2p4.
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Then the same person deletes that MDB entry. The cross-chip notifier for
deletion only matches sw0p0:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ ]
Why?
Because the DSA links are 'trunk' ports, if we just go ahead and delete
the MDB from sw1p4 and sw2p4 directly, we might delete those multicast
entries when they are still needed. Just consider the fact that somebody
does:
- add a multicast MAC address towards sw0p0 [ via the cross-chip
notifiers it gets installed on the DSA links too ]
- add the same multicast MAC address towards sw0p1 (another port of that
same switch)
- delete the same multicast MAC address from sw0p0.
At this point, if we deleted the MAC address from the DSA links, it
would be flooded, even though there is still an entry on switch 0 which
needs it not to.
So that is why deletions only match the targeted source port and nothing
on DSA links. Of course, dangling resources means that the hardware
tables will eventually run out given enough additions/removals, but hey,
at least it's simple.
But there is a bigger concern which needs to be addressed, and that is
our support for SWITCHDEV_OBJ_ID_HOST_MDB. DSA simply translates such an
object into a dsa_port_host_mdb_add() which ends up as ds->ops->port_mdb_add()
on the upstream port, and a similar thing happens on deletion:
dsa_port_host_mdb_del() will trigger ds->ops->port_mdb_del() on the
upstream port.
When there are 2 VLAN-unaware bridges spanning the same switch (which is
a use case DSA proudly supports), each bridge will install its own
SWITCHDEV_OBJ_ID_HOST_MDB entries. But upon deletion, DSA goes ahead and
emits a DSA_NOTIFIER_MDB_DEL for dp->cpu_dp, which is shared between the
user ports enslaved to br0 and the user ports enslaved to br1. Not good.
The host-trapped multicast addresses installed by br1 will be deleted
when any state changes in br0 (IGMP timers expire, or ports leave, etc).
To avoid this, we could of course go the route of the zero-sum game and
delete the DSA_NOTIFIER_MDB_DEL call for dp->cpu_dp. But the better
design is to just admit that on shared ports like DSA links and CPU
ports, we should be reference counting calls, even if this consumes some
dynamic memory which DSA has traditionally avoided. On the flip side,
the hardware tables of switches are limited in size, so it would be good
if the OS managed them properly instead of having them eventually
overflow.
To address the memory usage concern, we only apply the refcounting of
MDB entries on ports that are really shared (CPU ports and DSA links)
and not on user ports. In a typical single-switch setup, this means only
the CPU port (and the host MDB entries are not that many, really).
The name of the newly introduced data structures (dsa_mac_addr) is
chosen in such a way that will be reusable for host FDB entries (next
patch).
With this change, we can finally have the same matching logic for the
MDB additions and deletions, as well as for their host-trapped variants.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abd49535c3 ("net: dsa: execute dsa_switch_mdb_add only for
routing port in cross-chip topologies") does a surprisingly good job
even for the SWITCHDEV_OBJ_ID_HOST_MDB use case, where DSA simply
translates a switchdev object received on dp into a cross-chip notifier
for dp->cpu_dp.
To visualize how that works, imagine the daisy chain topology below and
consider a SWITCHDEV_OBJ_ID_HOST_MDB object emitted on sw2p0. How does
the cross-chip notifier know to match on all the right ports (sw0p4, the
dedicated CPU port, sw1p4, an upstream DSA link, and sw2p4, another
upstream DSA link)?
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
The answer is simple: the dedicated CPU port of sw2p0 is sw0p4, and
dsa_routing_port returns the upstream port for all switches.
That is fine, but there are other topologies where this does not work as
well. There are trees with "H" topologies in the wild, where there are 2
or more switches with DSA links between them, but every switch has its
dedicated CPU port. For these topologies, it seems stupid for the neighbor
switches to install an MDB entry on the routing port, since these
multicast addresses are fundamentally different than the usual ones we
support (and that is the justification for this patch, to introduce the
concept of a termination plane multicast MAC address, as opposed to a
forwarding plane multicast MAC address).
For example, when a SWITCHDEV_OBJ_ID_HOST_MDB would get added to sw0p0,
without this patch, it would get treated as a regular port MDB on sw0p2
and it would match on the ports below (including the sw1p3 routing port).
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ x ] [ ] [ ] [ ]
With the patch, the host MDB notifier on sw0p0 matches only on the local
switch, which is what we want for a termination plane address.
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] [ dsa ] [ cpu ] [ user ] [ user ]
[ ] [ ] [ x ] [ ] ---- [ ] [ ] [ ] [ ]
Name this new matching function "dsa_switch_host_address_match" since we
will be reusing it soon for host FDB entries as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add reference counting for FDB entries in cross-chip
topologies, and in order for that to have any chance of working and not
be unbalanced (leading to entries which are never deleted), we need to
ensure that higher layers are sane, because if they aren't, it's garbage
in, garbage out.
For example, if we add a bridge FDB entry twice, the bridge properly
errors out:
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
$ bridge fdb add dev swp0 00:01:02:03:04:07 master static
RTNETLINK answers: File exists
However, the same thing cannot be said about the bridge bypass
operations:
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ bridge fdb add dev swp0 00:01:02:03:04:07
$ echo $?
0
But one 'bridge fdb del' is enough to remove the entry, no matter how
many times it was added.
The bridge bypass operations are impossible to maintain in these
circumstances and lack of support for reference counting the cross-chip
notifiers is holding us back from making further progress, so just drop
support for them. The only way left for users to install static bridge
FDB entries is the proper one, using the "master static" flags.
With this change, rtnl_fdb_add() falls back to calling
ndo_dflt_fdb_add() which uses the duplicate-exclusive variant of
dev_uc_add(): dev_uc_add_excl(). Because DSA does not (yet) declare
IFF_UNICAST_FLT, this results in us going to promiscuous mode:
$ bridge fdb add dev swp0 00:01:02:03:04:05
[ 28.206743] device swp0 entered promiscuous mode
$ bridge fdb add dev swp0 00:01:02:03:04:05
RTNETLINK answers: File exists
So even if it does not completely fail, there is at least some indication
that it is behaving differently from before, and closer to user space
expectations, I would argue (the lack of a "local|static" specifier
defaults to "local", or "host-only", so dev_uc_add() is a reasonable
default implementation). If the generic implementation of .ndo_fdb_add
provided by Vlad Yasevich is a proof of anything, it only proves that
the implementation provided by DSA was always wrong, by not looking at
"ndm->ndm_state & NUD_NOARP" (the "static" flag which means that the FDB
entry points outwards) and "ndm->ndm_state & NUD_PERMANENT" (the "local"
flag which means that the FDB entry points towards the host). It all
used to mean the same thing to DSA.
Update the documentation so that the users are not confused about what's
going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port joins a bridge which already has local FDB entries pointing
to the bridge device itself, we would like to offload those, so allow
the "dev" argument to be equal to the bridge too. The code already does
what we need in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat addresses added to the bridge itself in the same way as regular
ports and send out a notification so that drivers may sync it down to
the hardware FDB.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Annotate the writer side of fdb->dst:
- fdb_create()
- br_fdb_update()
- fdb_add_entry()
- br_fdb_external_learn_add()
with WRITE_ONCE() and the reader side:
- br_fdb_test_addr()
- br_fdb_update()
- fdb_fill_info()
- fdb_add_entry()
- fdb_delete_by_addr_and_port()
- br_fdb_external_learn_add()
- br_switchdev_fdb_notify()
with compiler barriers such that the readers do not attempt to reload
fdb->dst multiple times, leading to potentially different destination
ports when the fdb entry is updated concurrently.
This is especially important in read-side sections where fdb->dst is
used more than once, but let's convert all accesses for the sake of
uniformity.
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi Linus,
Please, pull the following patches that fix many fall-through warnings
when building with Clang 12.0.0 and this[1] change reverted. Notice
that in order to enable -Wimplicit-fallthrough for Clang, such change[1]
is meant to be reverted at some point. So, these patches help to move
in that direction.
Thanks!
[1] commit e2079e93f5 ("kbuild: Do not enable -Wimplicit-fallthrough for clang for now")
-----BEGIN PGP SIGNATURE-----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=Kt2q
-----END PGP SIGNATURE-----
Merge tag 'fallthrough-fixes-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"Fix many fall-through warnings when building with Clang 12.0.0 and
'-Wimplicit-fallthrough' so that we at some point will be able to
enable that warning by default"
* tag 'fallthrough-fixes-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (26 commits)
rxrpc: Fix fall-through warnings for Clang
drm/nouveau/clk: Fix fall-through warnings for Clang
drm/nouveau/therm: Fix fall-through warnings for Clang
drm/nouveau: Fix fall-through warnings for Clang
xfs: Fix fall-through warnings for Clang
xfrm: Fix fall-through warnings for Clang
tipc: Fix fall-through warnings for Clang
sctp: Fix fall-through warnings for Clang
rds: Fix fall-through warnings for Clang
net/packet: Fix fall-through warnings for Clang
net: netrom: Fix fall-through warnings for Clang
ide: Fix fall-through warnings for Clang
hwmon: (max6621) Fix fall-through warnings for Clang
hwmon: (corsair-cpro) Fix fall-through warnings for Clang
firewire: core: Fix fall-through warnings for Clang
braille_console: Fix fall-through warnings for Clang
ipv4: Fix fall-through warnings for Clang
qlcnic: Fix fall-through warnings for Clang
bnxt_en: Fix fall-through warnings for Clang
netxen_nic: Fix fall-through warnings for Clang
...
Printing this stack dump multiple times does not provide additional
useful information, and consumes time in the data path. Printing once
is sufficient.
Changes
v2: Format indentation properly
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard IEC 62439-2, in case the node behaves as MRA
and needs to send Test frames on ring ports, then these Test frames need
to have an Option TLV and a Sub-Option TLV which has the type AUTO_MGR.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for QCA_ROME device (0cf3:e500) and RTL8822CE
- Update management interface revision to 21
- Use of incluse language
- Proper handling of HCI_LE_Advertising_Set_Terminated event
- Recovery handing of HCI ncmd=0
- Various memory fixes
-----BEGIN PGP SIGNATURE-----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=2NdY
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for QCA_ROME device (0cf3:e500) and RTL8822CE
- Update management interface revision to 21
- Use of incluse language
- Proper handling of HCI_LE_Advertising_Set_Terminated event
- Recovery handing of HCI ncmd=0
- Various memory fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first chunk in a packet is ensured to be present at the beginning of
sctp_rcv(), as a packet needs to have at least 1 chunk. But the second
one, may not be completely available and ch->length can be over
uninitialized memory.
Fix here is by only trying to walk on the next chunk if there is enough to
hold at least the header, and then proceed with the ch->length validation
that is already there.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilja reported that, simply putting it, nothing was validating that
from_addr_param functions were operating on initialized memory. That is,
the parameter itself was being validated by sctp_walk_params, but it
doesn't check for types and their specific sizes and it could be a 0-length
one, causing from_addr_param to potentially work over the next parameter or
even uninitialized memory.
The fix here is to, in all calls to from_addr_param, check if enough space
is there for the wanted IP address type.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch builds off of commit 2b246b2569
and adds functionality to respond to ICMPV6 PROBE requests.
Add icmp_build_probe function to construct PROBE requests for both
ICMPV4 and ICMPV6.
Modify icmpv6_rcv to detect ICMPV6 PROBE messages and call the
icmpv6_echo_reply handler.
Modify icmpv6_echo_reply to build a PROBE response message based on the
queried interface.
This patch has been tested using a branch of the iputils git repo which can
be found here: https://github.com/Juniper-Clinic-2020/iputils/tree/probe-request
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch port leaves a bonding interface that is under a
bridge, there might be dangling switchdev objects on that port left
behind, because the bridge is not aware that its lower interface (the
bond) changed state in any way.
Call the bridge replay helpers with adding=false before changing
dp->bridge_dev to NULL, because we need to simulate to
dsa_slave_port_obj_del() that these notifications were emitted by the
bridge.
We add this hook to the NETDEV_PRECHANGEUPPER event handler, because
we are calling into switchdev (and the __switchdev_handle_port_obj_del
fanout helpers expect the upper/lower adjacency lists to still be valid)
and PRECHANGEUPPER is the last moment in time when they still are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to add more logic to the DSA NETDEV_PRECHANGEUPPER event
handler, more exactly we need to request an unsync of switchdev objects.
In order to fit more code, refactor the existing logic into a helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
