Add support for the imx6q wanboard variant.
Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi
file that contains the common peripheral nodes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After mxs-dma driver adopts generic DMA device tree binding, gpmi
channel interrupt number is defined in DMA controller node, and
channel ID is listed in "dmas" property. So the DMA channel interrupt
number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which
are used by old customized DMA binding can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Only imx6q has the ahci sata controller, enable
it on imx6q platforms.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds core voltages for i.MX27 CPUs. Only 266 and 400 MHz modes
is documented in the datasheet, so we add a 266 MHz frequency for conform this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Wandboard has a bluetooth device connected to UART3, so add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Wandboard has a SD card slot on the baseboard connected to SDHC1 and a
BCM4329 (Wifi + Bluetooth chip) connected to SDHC2.
Add support for these ports.
While at it, provide the card detect gpio on SDHC3 and also fix indentation on
MX6QDL_PAD_GPIO_0__CCM_CLKO1 hog pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the dma property for all the uart.
Note: Add the dma property does not mean we enable the dma for this
uart.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the a new pinctrl for uart3. In the imx6q{dl}-sabreauto boards,
the uart3 is used for Bluetooth.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add more imx6q/dl pin groups for those supported boards, e.g. sabresd,
sabreauto, arm2.
IPU2 pin groups are added into imx6q.dtsi, since the block is only
available on imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
enable the uart2 for imx6q-arm2 board.
The uart2 works in the DTE mode, with the RTS/CTS and DMA enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In the arm2 board, the UART2 works in the dte mode.
So add a pinctrl for both the imx6q{dl} boards.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The uart2 in the imx6q-arm2 board is used as a DTE uart,
this patch adds the necessary DTE pads for uart2.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In order to enable the DMA for some uart port in imx6sl, we add the
"fsl,imx6q-uart" to the uart's compatible property.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Both buses are not used on the phyCARD-S module. This patch moves them
to the rdk file. Remove ioexpander.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This sensor was introduced in the original pca100 board file, but
phyCARD-S SOM and RDK do not have a temperature sensor.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
To make it consistent with the other i.mx SoCs, let's add the cpus nodes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fixup of commit "ARM: dts: Add device tree support for phycard pca100".
Remove wrong I2C RTC node.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds CAN (NXP SJA1000) node for Phytec PCM-970 RDK.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds WEIM node for Phytec PCM-038 module.
Migrate existing on-module NOR-flash as children of WEIM CS0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch moves IIM node under AIPI2 bus, since this is proper
location for this module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the #dma-cells property for all the sdma in all the imx platforms.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX6DL does not have the second IPU, but the LVDS multiplexers can connect
either LVDS channel of the LDB to IPU1 DI0 or IPU1 DI1.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[shawn.guo: remove "crtcs" property from imx6qdl.dtsi]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch enables the On-Chip SRAM (OCRAM) on i.MX53 and i.MX6 SoCs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".
Based on patches from:
Steffen Trumtrar <s.trumtrar@pengutronix.de>:
- Original patch
- ARM: dts: Set partition offsets for phycard
- ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
- ARM: imx27-phytec-phycard-S.dts: resize nand partitions
Jan Luebbe <jlu@pengutronix.de>:
- ARM: dts: Enable bad block table in NAND
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Set operating-points for imx27. There is no regulator support, so the
voltages are 0. The frequencies should be the same for all imx27 boards,
so it is defined here and can be overwritten if necessary.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On the MX27 Reference Manual the interrupt controller is named AITC:
ARM926EJ-S Interrupt Controller
So use the AITC term instead of AVIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Origin: id:1334193132-18944-2-git-send-email-festevam@gmail.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The mc13892 driver knows that it needs spi-cs-high, so the mc13892
will work. The dataflash also connected to this bus though can only
be probed when the mc13892 is inactive. Due to driver potential
differences in the probe order we can only make sure the mc13892
is inactive when we put the information into the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For keeping the alphabetical order in the pinmux nodes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c and spi devices correctly.
While at it reorder the aliases entries alphabetically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
