The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all the audio related device tree entries are handled by the
MFD code, for most parts of the Arizona driver we group the device
tree handling with the component that uses it and should do so here as
well.
Add handling in the ASoC code for the audio device tree entries, a
later patch removes the MFD side handling but there is no harm in it
being duplicated temporarily.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver has quite a few small initialisation functions, in
preparation for some refactoring add a new function arizona_init_common.
This will be used bus probe level initialisation that is common across
Arizona devices. For now just move the notifier chain initialisation in
there.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As requirements to bring up audio paths are continuous getting tighter
and the DSP download to most ADSP devices happens over an external bus
it can become an important factor in the path bring up time. As such
sometimes it is a reasonable trade off to download the firmware ahead of
when it will be required and take a small hit on power consumption for
keeping the core powered up.
This "preloading" adds an additional control for each DSP core "DSPx
Preload Switch" that when set to true will power up the DSP core and
download the firmware currently selected in the "DSPx Firmware" control.
Whilst the core is preloaded the current firmware can not be changed and
the CODEC will be kept powered up and SYSCLK held on. Although future
improvements may allow the SYSCLK to be powered down as well because
the hardware only requires SYSCLK whilst the download is actually taking
place, but this is not covered in this series.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions are given external linkage by default making the extern's
unnecessary, as such remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the DSP loading is split into two widgets, the preloader that
is a snd_soc_dapm_dai_link widget which starts a thread to download
the firmware, and the DSP itself which is a snd_soc_dapm_out_drv and
synchronises the thread back in to the DAPM sequence. This allows the
firmware download to be overlapped with the rest of the path bring up.
The use of a snd_soc_dapm_dai_link widget requires the preloader to be part
of the audio path in DAPM, really a supply widget is a better fit for the
preloader. The preloader is something that needs to be done for the DSP to
function, not a part of the audio path itself.
This change makes the DSP preloader widget a supply widget, which as well
as probably being a better fit will also make it much simpler to power up
the preloader widget to trigger firmware download to the core independently
of the audio path coming up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SYSCLK is attached to every compressed DAI as this follows the
pattern of attaching clocks to the chips inputs and outputs, however, it is
really the DSP that requires the clock here. As firmware download can be a
significant part of the path startup time for these devices occasionally it
would be desirable to download the firmware in advance of the path being
brought up.
To help facilitate this early firmware loading this patch attaches the
SYSCLK to the DSP preloader widget. This also saves us adding a new route
to SYSCLK every time a new compressed DAI is created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OUT4L and OUT4R widgets are not registered PRE_PMU or POST_PMD
events, as such the manual speaker enable on wm5102 does not actually
ever run. Furthermore since the issue actually only affected rev B of
the silicon which never shipped in volume, simply remove the work around
from the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64-bit builds would generate a warning when we passed the core number as
a pointer through the notifier data:
sound/soc/codecs/cs47l24.c:1091:13: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
(void *)i);
Rather than just fix this up with more casting add a data structure that
holds information for the notifier chain. This will make it easier to
add additional information in the future as well.
Fixes: 7baa7e2490 ("ASoC: arizona: Add event notification on voice trigger events")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some situations the voice control firmware will by used
to only provide a trigger notification event. In this case a
compressed stream will not be opened by user-space, as such we
need to provide a virtual output to power on the DSP in this
use-case. This patch adds a virtual output 'DSP Voice Trigger'
that can be used for this, and a switch that lets it be connected
to the core when required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inform the notifier chain if the DSP recognises a voice trigger.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly this adds DAI links for the audio trace, however, it is also
necessary to update the data IRQ handler to check more cores. We have
the handler check every core so it should not be necessary to update
this function if more compressed firmwares are added in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, various places in Arizona use "const char *" and "int".
This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5110 device contains a hardware ANC block, this patch connects up
controls and routing for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds convenience defines for declaring a gain control that
has an input mux. These blocks are functionally equivalent to
the existing mixer blocks but can only have a single input
active at once.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will occasionally require to take different action based on if an
input is analog or digital so add a helper function to return if an
input is analog.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The extcon driver takes the DAPM mutex from within the interrupt thread
in several places, which makes it possible to get into a situation where
the interrupt thread is blocked waiting on the DAPM mutex whilst a DAPM
sequence is running which is attempting to configure the FLL. In this
case the FLL completion can't be completed as as the IRQ handler is
ONE_SHOT, which cause the FLL lock to use the full time out (250mS) and
report that the process timed out.
It is not really practical to make the extcon driver not take the DAPM
mutex from within the interrupt thread, at least not without extensive
modification. So this patch fixes the issue by switching the wait for
the FLL lock to polling. A few fast polls are done first as the FLL
should lock quickly for a good quality reference clock, (indeed it hits
on the first poll on my system) and it will poll every 20mS after that
until it times out.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Specifying unstable coefficients for the low/high pass filters can have
a severe impact on the audio. This patchs adds a stability check on the
coefficients written to the low/high pass filter block to prevent this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifying unstable coefficients for the EQ can have a severe impact on
the audio. This patchs adds a stability check on the coefficients
written to the EQ, for this it is necessary to merge the mode control
and the coefficients as some coefficients may only be unstable with a
certain mode setting so it is ideal if these are always updated in sync.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.
This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs
Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM5102 and WM8997 codecs have an internal dynamic clock booster.
When this booster is active, the DCVDD voltage must be increased.
If all the currently active audio paths can run with the root SYSCLK
we can disable the booster, allowing us to turn down DCVDD voltage
to save power.
Previously this was being done by having the booster enable bit set
as a side-effect of the LDO1 regulator driver, which is unexpected
behaviour of a regulator and not compatible with using an external
regulator. [Originally this was documented as a feature of the internal
LDO -- broonie]
This patch exports functions to handle the booster enable and
DCVDD voltage, with each relevant subsystem flagging whether it can
currently run without the booster. Note that these subsystems are
stateless and none of them are nestable, so there's no need for
reference counting, we only need a simple boolean for each subsystem
of whether their current condition could require the booster or will
allow us to turn the codec down to lower operating power.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mixer core on the Arizona devices is powered up whenever any routing
is non-zero. This patch saves a little power and avoids a few difficult
corner cases (around the mixer core being powered whilst there is no
clock available), by using the autodisable mux functionality to only
write out the settings for the muxes when they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the wm5110 CODEC both the left and right channel must be powered
when an output is being used as a mono output, although no audio is
routed to the right output channel. This patch adds additional DAPM
routes to link the right channel to the left in the case where an output
is marked as mono. Audio must always be brought in on the left channel
for mono operation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the start of booting the DSP to earlier in the DAPM process, and
move the final starting of the DSP to later in the DAPM process. This
allows us to overlap some of the processing with other components of the
system being brought up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for configuring the sample rate on the SYSCLK side of the
ASRC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, the driver only supports configuration of the lower sample
rate (FSL) on the ISRCs. With the higher rate being fixed a SYSCLK, this
patch adds support for configuring the higher sample rate (FSH).
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IhEz
-----END PGP SIGNATURE-----
Merge tag 'ib-asoc-1' of git://git.linaro.org/people/ljones/mfd into asoc-arizona
Immutable branch for ASoC, as requested by Mark Brown
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: D.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The routes linking the widget and the input mux were being added
manually, rather than by the ARIZONA_MUX_ROUTES macro. This patchs adds
the routes to the macro.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The input OSR bits are specified differently for wm5110 than for current
revs of wm5102. This patch corrects support for this on wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When doing signal activity detection, the only output from the DRC will
often be a GPIO pin. This patch adds a signal activity output that is
activated when a GPIO is configured to output the DRC signal activity
detection.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into asoc-arizona
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
