noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx8m_clk_hw_composite_bus api for bus clk root slice usage.
Because the mux switch sequence issue, we could not reuse Peripheral
Clock Slice code, need use composite specific mux operation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the imx clocks that need to be registered by the audiomix need to
pass on the device so that the runtime PM support could work properly.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to allow runtime PM, the device needs to be passed on
to the register function. Audiomix clock controller, used on
i.MX8MP and future platforms, registers a pll14xx and has runtime
PM support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audiomix on i.MX8MP registers two gates that share the same enable count
but use the same bit to control the gate instead of two bits. By adding
the flag IMX_CLK_GATE2_SINGLE_BIT we allow the gate2 to use the generic
gate ops for enable, disable and is_enabled.
For the disable_unused, nothing happens if this flag is specified.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are several clock slices, current composite code
only support bus/ip clock slices, it could not support core
slice.
So introduce a new API imx8m_clk_hw_composite_core to support
core slice. To core slice, post divider with 3 bits width and
no pre divider. Other fields are same as bus/ip slices.
Add a flag IMX_COMPOSITE_CORE for the usecase.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_gate4_flags() function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_hw_gate3_flags function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce hw based API imx_clk_hw_mux2_flags, then we could
convert i.MX8MN clk driver to use hw based APIs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a non hw API based imx_unregister_clocks to unregister clocks
when of_clk_add_provider failed. Add a hw API based
imx_unregister_hw_clocks when of_clk_add_hw_provider failed.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx8m_clk_hw_composite_flags function to clk_hw based API,
rename accordingly and add a macro for clk based legacy. This allows
us to move closer to a clear split between consumer and provider clk
APIs.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pll14xx function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renaming the imx_clk_divider_gate register function to imx_clk_hw_divider_gate
to be more obvious it is clk_hw based.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renaming the imx_clk_pfdv2 register function to imx_clk_hw_pfdv2 to be
more obvious it is clk_hw based.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renaming the imx_clk_pllv4 register function to imx_clk_hw_pllv4 to be
more obvious it is clk_hw based.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renaming the imx_clk_frac_pll and imx_clk_sccg_pll register functions to
imx_clk_hw_frac_pll, respectively imx_clk_hw_sccg_pll to be more obvious
that they are clk_hw based.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Renaming the imx7ulp_clk_composite register function to
imx7ulp_clk_hw_composite to show it is clk_hw based.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pllv2 register function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pllv1 register function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replacing with macros all the clk based API helpers we reduce the code
duplication. The end goal is to get rid of all these macros when there
will be no more users of the clk based API, that is, when all the i.MX
clock provider drivers will be switched completely to the clk_hw based
API.
This is another step in moving away from the non clk_hw based API usage
throughout the i.MX clock drivers. The reason for doing that is to
have a clear split between the clock provider and the clock consumer API.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the manual the acronym stands for
Spread Sprectum Clock Generator.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If the clk_hw based API returns an error, trying to return the clk from
hw will end up in a NULL pointer dereference. So adding the to_clk
checker and using it inside every clk based macro helper we handle that
case correctly.
This to_clk is also temporary and will go away along with the clk based
macro helpers once there is no user that need them anymore.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM frequency switches are executed in firmware and can change the
configuration of the DRAM PLL outside linux. Mark these CLKs with
CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and
recalculate rates.
In current DRAM frequency tables on 8mm/8mn only the maximum frequency
uses the PLL so it's always configured in the same way. However reading
back the PLL configuration is the correct behavior and allows additional
setpoints in the future.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_register_uart_clocks_hws() function is NOT implemented
at all, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the i.MX6 and i.MX7 clock drivers have been switched to clk_hw based,
we can remove the clk based API that is not used by any i.MX clock driver.
The following APIs are going away now:
- imx_clk_busy_divider
- imx_clk_busy_mux
- imx_clk_fixup_divider
- imx_clk_fixup_mux
- imx_clk_mux_ldb
- imx_clk_gate_dis_flags
- imx_clk_gate_flags
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For i.MX clock drivers probe fail case, clks should be unregistered
in the return path, this patch adds a common API for i.MX clock
drivers to unregister clocks when fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1416X/1443X PLL are used on i.MX8MM and i.MX8MN and maybe
other i.MX8M series SoC later, the macro definitions of
these PLLs' initialization should be common for usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the wrappers to clk_hw based API and rename them to indicate
that. Add macros for clk based legacy users. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_mux function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. a macro for clk
based legacy. This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_divider function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_gate_exclusive function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pfd function to clk_hw based API, rename accordingly
and add a macro for clk based legacy. This allows us to move closer to
a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_hw_pllv3 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us
to move closer to a clear split between consumer and provider clk
APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_register_gate2 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_cpu clock registering function to clk_hw based API and add
a macro for clk based legacy. This allows us to move closer to a clear
split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the clk_busy clock registering functions to clk_hw based API.
Keep around some clk based wrappers to be used by older imx platforms.
This allows us to move closer to a clear split of consumer and provider
clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to move to clk_hw based API, imx_obtain_fixed_clock_hw
is added. The end goal here is to have all the clk providers use
the clk_hw based API.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All i.MX6 SoCs need to mask unused MMDC channel's handshake
for low power modes, this patch provides common API for masking
the MMDC channel passed from caller.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According reference manual, i.MX7D's audio/video PLL's
num/denom register offset are 0x20/0x30, they are different
from i.MX6's audio/video PLL, correct it by introducing new
offset variables for audio/video PLL and using runtime
assignment based on PLL type.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is never used and the imx_clk_hw_fixed does the same thing.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the entire combination of plls to be one single clock. The parents used
for bypasses are specified each as an index in the parents list.
The determine_rate does a lookup throughout all the possible combinations
for all the divs and returns the best possible 'setup' which in turn is used
by set_rate later to set up all the divs and bypasses.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parents needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parent_names needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock providers are recommended to use the new struct clk_hw based API,
so implement IMX clk_hw based provider helpers functions to the new
approach.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
