Even if some CPUs have excessive numbers of callbacks, RCU's grace-period
kthread will still wait normally between successive force-quiescent-state
scans. The first two are the most important, as they are the ones that
enlist aid from the scheduler when overloaded. This commit therefore
omits the wait before the first and the second force-quiescent-state
scan under callback-overload conditions.
This approach was inspired by a discussion with Jeff Roberson.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Although the accesses used to determine whether or not a stall should
be printed are an integral part of the concurrency algorithm governing
use of the corresponding variables, the values that are simply printed
are ancillary. As such, it is best to use data_race() for these accesses
in order to provide the greatest latitude in the use of KCSAN for the
other accesses that are an integral part of the algorithm. This commit
therefore changes the relevant uses of READ_ONCE() to data_race().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_node structure's ->boost_tasks field is read locklessly, so this
commit adds the WRITE_ONCE() to an update in order to provide proper
documentation and READ_ONCE()/WRITE_ONCE() pairing.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The srcu_data structure's ->srcu_lock_count and ->srcu_unlock_count arrays
are read and written locklessly, so this commit adds the data_race()
to the diagnostic-print loads from these arrays in order mark them as
known and approved data-racy accesses.
This data race was reported by KCSAN. Not appropriate for backporting due
to failure being unlikely and due to this being used only by rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_node structure's ->boost_tasks field is read locklessly, so this
commit adds the READ_ONCE() to one load in order to avoid destructive
compiler optimizations. The other load is from a diagnostic print,
so data_race() suffices.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
There are lockless loads from the rcu_node structure's ->exp_tasks field,
so this commit causes all stores to use WRITE_ONCE() and all lockless
loads to use READ_ONCE() or data_race(), with the latter for debug
prints. This code also did a unprotected traversal of the linked list
pointed into by ->exp_tasks, so this commit also acquires the rcu_node
structure's ->lock to properly protect this traversal. This list was
traversed unprotected only when printing an RCU CPU stall warning for
an expedited grace period, so the odds of seeing this in production are
not all that high.
This data race was reported by KCSAN.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_state structure's ncpus field is only to be modified by the
CPU-hotplug CPU-online code path, which is single-threaded. This
commit therefore enlists KCSAN's help in enforcing this restriction.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This commit adds stubs for KCSAN's data_race(), ASSERT_EXCLUSIVE_WRITER(),
and ASSERT_EXCLUSIVE_ACCESS() macros to allow code using these macros to
move ahead.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This commit adds stubs for KCSAN's data_race(), ASSERT_EXCLUSIVE_WRITER(),
and ASSERT_EXCLUSIVE_ACCESS() macros to allow code using these macros to
move ahead.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_nmi_enter_common() function can be invoked both in interrupt
and NMI handlers. If it is invoked from process context (as opposed
to userspace or idle context) on a nohz_full CPU, it might acquire the
CPU's leaf rcu_node structure's ->lock. Because this lock is held only
with interrupts disabled, this is safe from an interrupt handler, but
doing so from an NMI handler can result in self-deadlock.
This commit therefore adds "irq" to the "if" condition so as to only
acquire the ->lock from irq handlers or process context, never from
an NMI handler.
Fixes: 5b14557b07 ("rcu: Avoid tick_dep_set_cpu() misordering")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: <stable@vger.kernel.org> # 5.5.x
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
Currently, rcu_barrier() ignores offline CPUs, However, it is possible
for an offline no-CBs CPU to have callbacks queued, and rcu_barrier()
must wait for those callbacks. This commit therefore makes rcu_barrier()
directly invoke the rcu_barrier_func() with interrupts disabled for such
CPUs. This requires passing the CPU number into this function so that
it can entrain the rcu_barrier() callback onto the correct CPU's callback
list, given that the code must instead execute on the current CPU.
While in the area, this commit fixes a bug where the first CPU's callback
might have been invoked before rcu_segcblist_entrain() returned, which
would also result in an early wakeup.
Fixes: 5d6742b377 ("rcu/nocb: Use rcu_segcblist for no-CBs CPUs")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
[ paulmck: Apply optimization feedback from Boqun Feng. ]
Cc: <stable@vger.kernel.org> # 5.5.x
The rcu_state structure's gp_seq field is only to be modified by the RCU
grace-period kthread, which is single-threaded. This commit therefore
enlists KCSAN's help in enforcing this restriction.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Mark irq_work items with IRQ_WORK_HARD_IRQ which should be invoked in
hardirq context even on PREEMPT_RT. IRQ_WORK without this flag will be
invoked in softirq context on PREEMPT_RT.
Set ->irq_config to 1 for the IRQ_WORK items which are invoked in softirq
context so lockdep knows that these can safely acquire a spinlock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113242.643576700@linutronix.de
Extend lockdep to validate lock wait-type context.
The current wait-types are:
LD_WAIT_FREE, /* wait free, rcu etc.. */
LD_WAIT_SPIN, /* spin loops, raw_spinlock_t etc.. */
LD_WAIT_CONFIG, /* CONFIG_PREEMPT_LOCK, spinlock_t etc.. */
LD_WAIT_SLEEP, /* sleeping locks, mutex_t etc.. */
Where lockdep validates that the current lock (the one being acquired)
fits in the current wait-context (as generated by the held stack).
This ensures that there is no attempt to acquire mutexes while holding
spinlocks, to acquire spinlocks while holding raw_spinlocks and so on. In
other words, its a more fancy might_sleep().
Obviously RCU made the entire ordeal more complex than a simple single
value test because RCU can be acquired in (pretty much) any context and
while it presents a context to nested locks it is not the same as it
got acquired in.
Therefore its necessary to split the wait_type into two values, one
representing the acquire (outer) and one representing the nested context
(inner). For most 'normal' locks these two are the same.
[ To make static initialization easier we have the rule that:
.outer == INV means .outer == .inner; because INV == 0. ]
It further means that its required to find the minimal .inner of the held
stack to compare against the outer of the new lock; because while 'normal'
RCU presents a CONFIG type to nested locks, if it is taken while already
holding a SPIN type it obviously doesn't relax the rules.
Below is an example output generated by the trivial test code:
raw_spin_lock(&foo);
spin_lock(&bar);
spin_unlock(&bar);
raw_spin_unlock(&foo);
[ BUG: Invalid wait context ]
-----------------------------
swapper/0/1 is trying to lock:
ffffc90000013f20 (&bar){....}-{3:3}, at: kernel_init+0xdb/0x187
other info that might help us debug this:
1 lock held by swapper/0/1:
#0: ffffc90000013ee0 (&foo){+.+.}-{2:2}, at: kernel_init+0xd1/0x187
The way to read it is to look at the new -{n,m} part in the lock
description; -{3:3} for the attempted lock, and try and match that up to
the held locks, which in this case is the one: -{2,2}.
This tells that the acquiring lock requires a more relaxed environment than
presented by the lock stack.
Currently only the normal locks and RCU are converted, the rest of the
lockdep users defaults to .inner = INV which is ignored. More conversions
can be done when desired.
The check for spinlock_t nesting is not enabled by default. It's a separate
config option for now as there are known problems which are currently
addressed. The config option allows to identify these problems and to
verify that the solutions found are indeed solving them.
The config switch will be removed and the checks will permanently enabled
once the vast majority of issues has been addressed.
[ bigeasy: Move LD_WAIT_FREE,… out of CONFIG_LOCKDEP to avoid compile
failure with CONFIG_DEBUG_SPINLOCK + !CONFIG_LOCKDEP]
[ tglx: Add the config option ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113242.427089655@linutronix.de
Currently, if rcu_barrier() returns too soon, the test waits 100ms and
then does another instance of the test. However, if rcu_barrier() were
to have waited for more than 100ms too short a time, this could cause
the test's rcu_head structures to be reused while they were still on
RCU's callback lists. This can result in knock-on errors that obscure
the original rcu_barrier() test failure.
This commit therefore adds code that attempts to wait until all of
the test's callbacks have been invoked. Of course, if RCU completely
lost track of the corresponding rcu_head structures, this wait could be
forever. This commit therefore also complains if this attempted recovery
takes more than one second, and it also gives up when the test ends.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Currently, rcu_torture_barrier_cbs() posts callbacks from whatever CPU
it is running on, which means that all these kthreads might well be
posting from the same CPU, which would drastically reduce the effectiveness
of this test. This commit therefore uses IPIs to make the callbacks be
posted from the corresponding CPU (given by local variable myid).
If the IPI fails (which can happen if the target CPU is offline or does
not exist at all), the callback is posted on whatever CPU is currently
running.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
During changes to kfree_rcu() code, we often check the amount of free
memory. As an alternative to checking this manually, this commit adds a
measurement in the test itself. It measures four times during the test
for available memory, digitally filters these measurements to produce a
running average with a weight of 0.5, and compares this digitally filtered
value with the amount of available memory at the beginning of the test.
Something like the following is printed at the end of the run:
Total time taken by all kfree'ers: 6369738407 ns, loops: 10000, batches: 764, memory footprint: 216MB
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcutorture global variable rcu_torture_current is accessed locklessly,
so it must use the RCU pointer load/store primitives. This commit
therefore adds several that were missed.
This data race was reported by KCSAN. Not appropriate for backporting due
to failure being unlikely and due to this being used only by rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcutorture rcu_torture_count and rcu_torture_batch per-CPU variables
are read locklessly, so this commit adds the READ_ONCE() to a load in
order to avoid various types of compiler vandalism^Woptimization.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely and due to this being rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_fwd_cb_nodelay variable suppresses excessively long read-side
delays while carrying out an rcutorture forward-progress test. As such,
it is accessed both by readers and updaters, and most of the accesses
therefore use *_ONCE(). Except for one in rcu_read_delay(), which this
commit fixes.
This data race was reported by KCSAN. Not appropriate for backporting
due to this being rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The ->rtort_pipe_count field in the rcu_torture structure checks for
too-short grace periods, and is therefore read by rcutorture's readers
while being updated by rcutorture's writers. This commit therefore
adds the needed READ_ONCE() and WRITE_ONCE() invocations.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely and due to this being rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
In normal production, an excessively long wait on a grace period
(synchronize_rcu(), for example) at boottime is often just as bad
as at any other time. In fact, given the desire for fast boot, any
sort of long wait at boot is a bad idea. However, heavy rcutorture
testing on large hyperthreaded systems can generate such long waits
during boot as a matter of course. This commit therefore causes
the rcupdate.rcu_cpu_stall_suppress_at_boot kernel boot parameter to
suppress reporting of bootime bad-sequence warning due to excessively
long grace-period waits.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
In normal production, an RCU CPU stall warning at boottime is often
just as bad as at any other time. In fact, given the desire for fast
boot, any sort of long-term stall at boot is a bad idea. However,
heavy rcutorture testing on large hyperthreaded systems can generate
boottime RCU CPU stalls as a matter of course. This commit therefore
provides a kernel boot parameter that suppresses reporting of boottime
RCU CPU stall warnings and similarly of rcutorture writer stalls.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Additional rcutorture aggression can result in, believe it or not,
boot times in excess of three minutes on large hyperthreaded systems.
This is long enough for rcutorture to decide to do some callback flooding,
which seems a bit excessive given that userspace cannot have started
until long after boot, and it is userspace that does the real-world
callback flooding. Worse yet, because Tiny RCU lacks forward-progress
functionality, the looping-in-the-kernel tests can also be problematic
during early boot.
This commit therefore causes rcutorture to hold off on callback
flooding until about the time that init is spawned, and the same
for looping-in-the-kernel tests for Tiny RCU.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Some larger systems can take in excess of 50 seconds to complete their
early boot initcalls prior to spawing init. This does not in any way
help the forward-progress judgments of built-in rcutorture (when
rcutorture is built as a module, the insmod or modprobe command normally
cannot happen until some time after boot completes). This commit
therefore suppresses such complaints until about the time that init
is spawned.
This also includes a fix to a stupid error located by kbuild test robot.
[ paulmck: Apply kbuild test robot feedback. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
[ paulmck: Fix to nohz_full slow-expediting recovery logic, per bpetkov. ]
[ paulmck: Restrict splat to CONFIG_PREEMPT_RT=y kernels and simplify. ]
Tested-by: Borislav Petkov <bp@alien8.de>
A read of the srcu_struct structure's ->srcu_gp_seq field should not
need READ_ONCE() when that structure's ->lock is held. Except that this
lock is not always held when updating this field. This commit therefore
acquires the lock around updates and removes a now-unneeded READ_ONCE().
This data race was reported by KCSAN.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
[ paulmck: Switch from READ_ONCE() to lock per Peter Zilstra question. ]
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
The srcu_struct structure's ->srcu_idx field is accessed locklessly,
so reads must use READ_ONCE(). This commit therefore adds the needed
READ_ONCE() invocation where it was missed.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The srcu_struct structure's ->srcu_gp_seq_needed_exp field is accessed
locklessly, so updates must use WRITE_ONCE(). This commit therefore
adds the needed WRITE_ONCE() invocations.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The srcu_node structure's ->srcu_gp_seq_needed_exp field is accessed
locklessly, so updates must use WRITE_ONCE(). This commit therefore
adds the needed WRITE_ONCE() invocations.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Sparse reports a warning at exit_tasks_rcu_finish(void)
|warning: context imbalance in exit_tasks_rcu_finish()
|- wrong count at exit
To fix this, this commit adds a __releases(&tasks_rcu_exit_srcu).
Given that exit_tasks_rcu_finish() does actually call __srcu_read_lock(),
this not only fixes the warning but also improves on the readability of
the code.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Sparse reports a warning at exit_tasks_rcu_start(void)
|warning: context imbalance in exit_tasks_rcu_start() - wrong count at exit
To fix this, this commit adds an __acquires(&tasks_rcu_exit_srcu).
Given that exit_tasks_rcu_start() does actually call __srcu_read_lock(),
this not only fixes the warning but also improves on the readability of
the code.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
The RCU tasks list of callbacks, rcu_tasks_cbs_head, is sampled locklessly
by rcu_tasks_kthread() when waiting for work to do. This commit therefore
applies READ_ONCE() to that lockless sampling and WRITE_ONCE() to the
single potential store outside of rcu_tasks_kthread.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The __call_rcu() function's header comment refers to a cpu argument
that no longer exists, and the comment of the return path from
rcu_nocb_try_bypass() ignores the non-no-CBs CPU case. This commit
therefore update both comments.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This commit fixes a spelling mistake in a pr_info() message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
RCU priority boosting currently is not applied until the grace period
is at least 250 milliseconds old (or the number of milliseconds specified
by the CONFIG_RCU_BOOST_DELAY Kconfig option). Although this has worked
well, it can result in OOM under conditions of RCU callback flooding.
One can argue that the real-time systems using RCU priority boosting
should carefully avoid RCU callback flooding, but one can just as well
argue that an OOM is a rather obnoxious error message.
This commit therefore disables the RCU priority boosting delay when
there are excessive numbers of callbacks queued.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
In default configutions, RCU currently waits at least 100 milliseconds
before asking cond_resched() and/or resched_rcu() for help seeking
quiescent states to end a grace period. But 100 milliseconds can be
one good long time during an RCU callback flood, for example, as can
happen when user processes repeatedly open and close files in a tight
loop. These 100-millisecond gaps in successive grace periods during a
callback flood can result in excessive numbers of callbacks piling up,
unnecessarily increasing memory footprint.
This commit therefore asks cond_resched() and/or resched_rcu() for help
as early as the first FQS scan when at least one of the CPUs has more
than 20,000 callbacks queued, a number that can be changed using the new
rcutree.qovld kernel boot parameter. An auxiliary qovld_calc variable
is used to avoid acquisition of locks that have not yet been initialized.
Early tests indicate that this reduces the RCU-callback memory footprint
during rcutorture floods by from 50% to 4x, depending on configuration.
Reported-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Reported-by: Tejun Heo <tj@kernel.org>
[ paulmck: Fix bug located by Qian Cai. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Qian Cai <cai@lca.pw>
The rcu_data structure's ->core_needs_qs field does not necessarily get
cleared in a timely fashion after the corresponding CPUs' quiescent state
has been reported. From a functional viewpoint, no harm done, but this
can result in excessive invocation of RCU core processing, as witnessed
by the kernel test robot, which saw greatly increased softirq overhead.
This commit therefore restores the rcu_report_qs_rdp() function's
clearing of this field, but only when running on the corresponding CPU.
Cases where some other CPU reports the quiescent state (for example, on
behalf of an idle CPU) are handled by setting this field appropriately
within the __note_gp_changes() function's end-of-grace-period checks.
This handling is carried out regardless of whether the end of a grace
period actually happened, thus handling the case where a CPU goes non-idle
after a quiescent state is reported on its behalf, but before the grace
period ends. This fix also avoids cross-CPU updates to ->core_needs_qs,
While in the area, this commit changes the __note_gp_changes() need_gp
variable's name to need_qs because it is a quiescent state that is needed
from the CPU in question.
Fixes: ed93dfc6bc ("rcu: Confine ->core_needs_qs accesses to the corresponding CPU")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The event is given three parameters, first one is the name
of RCU flavour, second one is the number of elements in array
for free and last one is an address of the array holding
pointers to be freed by the kfree_bulk() function.
To enable the trace event your kernel has to be build with
CONFIG_RCU_TRACE=y, after that it is possible to track the
events using ftrace subsystem.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The kfree_rcu() logic can be improved further by using kfree_bulk()
interface along with "basic batching support" introduced earlier.
The are at least two advantages of using "bulk" interface:
- in case of large number of kfree_rcu() requests kfree_bulk()
reduces the per-object overhead caused by calling kfree()
per-object.
- reduces the number of cache-misses due to "pointer chasing"
between objects which can be far spread between each other.
This approach defines a new kfree_rcu_bulk_data structure that
stores pointers in an array with a specific size. Number of entries
in that array depends on PAGE_SIZE making kfree_rcu_bulk_data
structure to be exactly one page.
Since it deals with "block-chain" technique there is an extra
need in dynamic allocation when a new block is required. Memory
is allocated with GFP_NOWAIT | __GFP_NOWARN flags, i.e. that
allows to skip direct reclaim under low memory condition to
prevent stalling and fails silently under high memory pressure.
The "emergency path" gets maintained when a system is run out of
memory. In that case objects are linked into regular list.
The "rcuperf" was run to analyze this change in terms of memory
consumption and kfree_bulk() throughput.
1) Testing on the Intel(R) Xeon(R) W-2135 CPU @ 3.70GHz, 12xCPUs
with following parameters:
kfree_loops=200000 kfree_alloc_num=1000 kfree_rcu_test=1 kfree_vary_obj_size=1
dev.2020.01.10a branch
Default / CONFIG_SLAB
53607352517 ns, loops: 200000, batches: 1885, memory footprint: 1248MB
53529637912 ns, loops: 200000, batches: 1921, memory footprint: 1193MB
53570175705 ns, loops: 200000, batches: 1929, memory footprint: 1250MB
Patch / CONFIG_SLAB
23981587315 ns, loops: 200000, batches: 810, memory footprint: 1219MB
23879375281 ns, loops: 200000, batches: 822, memory footprint: 1190MB
24086841707 ns, loops: 200000, batches: 794, memory footprint: 1380MB
Default / CONFIG_SLUB
51291025022 ns, loops: 200000, batches: 1713, memory footprint: 741MB
51278911477 ns, loops: 200000, batches: 1671, memory footprint: 719MB
51256183045 ns, loops: 200000, batches: 1719, memory footprint: 647MB
Patch / CONFIG_SLUB
50709919132 ns, loops: 200000, batches: 1618, memory footprint: 456MB
50736297452 ns, loops: 200000, batches: 1633, memory footprint: 507MB
50660403893 ns, loops: 200000, batches: 1628, memory footprint: 429MB
in case of CONFIG_SLAB there is double increase in performance and
slightly higher memory usage. As for CONFIG_SLUB, the performance
figures are better together with lower memory usage.
2) Testing on the HiKey-960, arm64, 8xCPUs with below parameters:
CONFIG_SLAB=y
kfree_loops=200000 kfree_alloc_num=1000 kfree_rcu_test=1
102898760401 ns, loops: 200000, batches: 5822, memory footprint: 158MB
89947009882 ns, loops: 200000, batches: 6715, memory footprint: 115MB
rcuperf shows approximately ~12% better throughput in case of
using "bulk" interface. The "drain logic" or its RCU callback
does the work faster that leads to better throughput.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Currently, nocb_gp_wait() unconditionally complains if there is a
callback not already associated with a grace period. This assumes that
either there was no such callback initially on the one hand, or that
the rcu_advance_cbs() function assigned all such callbacks to a grace
period on the other. However, in theory there are some situations that
would prevent rcu_advance_cbs() from assigning all of the callbacks.
This commit therefore checks for unassociated callbacks immediately after
rcu_advance_cbs() returns, while the corresponding rcu_node structure's
->lock is still held. If there are unassociated callbacks at that point,
the subsequent WARN_ON_ONCE() is disabled.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The ->nocb_lock lockdep assertion is currently guarded by cpu_online(),
which is incorrect for no-CBs CPUs, whose callback lists must be
protected by ->nocb_lock regardless of whether or not the corresponding
CPU is online. This situation could result in failure to detect bugs
resulting from failing to hold ->nocb_lock for offline CPUs.
This commit therefore removes the cpu_online() guard.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This commit reworks the atomic_cmpxchg() loop in rcu_eqs_special_set()
to do only the initial read from the current CPU's rcu_data structure's
->dynticks field explicitly. On subsequent passes, this value is instead
retained from the failing atomic_cmpxchg() operation.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Sparse reports warning at rcu_nocb_bypass_unlock()
warning: context imbalance in rcu_nocb_bypass_unlock() - unexpected unlock
The root cause is a missing annotation of rcu_nocb_bypass_unlock()
which causes the warning.
This commit therefore adds the missing __releases(&rdp->nocb_bypass_lock)
annotation.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Sparse reports warning at rcu_nocb_bypass_lock()
|warning: context imbalance in rcu_nocb_bypass_lock() - wrong count at exit
To fix this, this commit adds an __acquires(&rdp->nocb_bypass_lock).
Given that rcu_nocb_bypass_lock() does actually call raw_spin_lock()
when raw_spin_trylock() fails, this not only fixes the warning but also
improves on the readability of the code.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Currently rcu_check_gp_start_stall() complains if a grace period takes
too long to start, where "too long" is roughly one RCU CPU stall-warning
interval. This has worked well, but there are some debugging Kconfig
options (such as CONFIG_EFI_PGT_DUMP=y) that can make booting take a
very long time, so much so that the stall-warning interval has expired
before RCU's grace-period kthread has even been spawned.
This commit therefore resets the rcu_state.gp_req_activity and
rcu_state.gp_activity timestamps just before the grace-period kthread
is spawned, and modifies the checks and adds ordering to ensure that
if rcu_check_gp_start_stall() sees that the grace-period kthread
has been spawned, that it will also see the resets applied to the
rcu_state.gp_req_activity and rcu_state.gp_activity timestamps.
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
[ paulmck: Fix whitespace issues reported by Qian Cai. ]
Tested-by: Qian Cai <cai@lca.pw>
[ paulmck: Simplify grace-period wakeup check per Steve Rostedt feedback. ]
The rcu_barrier_callback() function does an atomic_dec_and_test(), and
if it is the last CPU to check in, does the required wakeup. Either way,
it does an event trace. Unfortunately, this is susceptible to the
following sequence of events:
o CPU 0 invokes rcu_barrier_callback(), but atomic_dec_and_test()
says that it is not last. But at this point, CPU 0 is delayed,
perhaps due to an NMI, SMI, or vCPU preemption.
o CPU 1 invokes rcu_barrier_callback(), and atomic_dec_and_test()
says that it is last. So CPU 1 traces completion and does
the needed wakeup.
o The awakened rcu_barrier() function does cleanup and releases
rcu_state.barrier_mutex.
o Another CPU now acquires rcu_state.barrier_mutex and starts
another round of rcu_barrier() processing, including updating
rcu_state.barrier_sequence.
o CPU 0 gets its act back together and does its tracing. Except
that rcu_state.barrier_sequence has already been updated, so
its tracing is incorrect and probably quite confusing.
(Wait! Why did this CPU check in twice for one rcu_barrier()
invocation???)
This commit therefore causes rcu_barrier_callback() to take a
snapshot of the value of rcu_state.barrier_sequence before invoking
atomic_dec_and_test(), thus guaranteeing that the event-trace output
is sensible, even if the timing of the event-trace output might still
be confusing. (Wait! Why did the old rcu_barrier() complete before
all of its CPUs checked in???) But being that this is RCU, only so much
confusion can reasonably be eliminated.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely and due to the mild consequences of the
failure, namely a confusing event trace.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The rcu_state structure's ->gp_start field is read locklessly, so this
commit adds the WRITE_ONCE() to an update in order to provide proper
documentation and READ_ONCE()/WRITE_ONCE() pairing.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
