This one should be using the default LPM policy for mobile chipsets so
add the PCI ID to the driver list of supported revices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
While whitelisting Micron M500DC drives, the tweaked blacklist entry
enabled queued TRIM from M500IT variants also. But these do not support
queued TRIM. And while using those SSDs with the latest kernel we have
seen errors and even the partition table getting corrupted.
Some part from the dmesg:
[ 6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133
[ 6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 6.741026] ata1.00: supports DRM functions and may not be fully accessible
[ 6.759887] ata1.00: configured for UDMA/133
[ 6.762256] scsi 0:0:0:0: Direct-Access ATA Micron_M500IT_MT MU01 PQ: 0 ANSI: 5
and then for the error:
[ 120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen
[ 120.860338] ata1.00: irq_stat 0x40000008
[ 120.860342] ata1.00: failed command: SEND FPDMA QUEUED
[ 120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 120.860353] ata1.00: status: { DRDY }
[ 120.860543] ata1: hard resetting link
[ 121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 121.166376] ata1.00: supports DRM functions and may not be fully accessible
[ 121.186238] ata1.00: supports DRM functions and may not be fully accessible
[ 121.204445] ata1.00: configured for UDMA/133
[ 121.204454] ata1.00: device reported invalid CHS sector 0
[ 121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current]
[ 121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4
[ 121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00
[ 121.204559] print_req_error: I/O error, dev sda, sector 272512
After few reboots with these errors, and the SSD is corrupted.
After blacklisting it, the errors are not seen and the SSD does not get
corrupted any more.
Fixes: 243918be63 ("libata: Do not blacklist Micron M500DC")
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sandisk SSDs SD7SN6S256G and SD8SN8U256G are regularly locking up
regularly under sustained moderate load with NCQ enabled. Blacklist
for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: stable@vger.kernel.org
__printf is useful to verify format and arguments. Remove the following
warning (with W=1):
drivers/ata/libata-eh.c:183:10: warning: function might be possible candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Trivial fix to spelling mistake in sil24_cerr_info message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Richard Jones has reported that using med_power_with_dipm on a T450s
with a Sandisk SD7UB3Q256G1001 SSD (firmware version X2180501) is
causing the machine to hang.
Switching the LPM to max_performance fixes this, so it seems that
this Sandisk SSD does not handle LPM well.
Note in the past there have been bug-reports about the following
Sandisk models not working with min_power, so we may need to extend
the quirk list in the future: name - firmware
Sandisk SD6SB2M512G1022I - X210400
Sandisk SD6PP4M-256G-1006 - A200906
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Kevin Shanahan reports the following repeating errors when using LPM,
causing long delays accessing the disk:
Apr 23 10:21:43 link kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x50000 action 0x6 frozen
Apr 23 10:21:43 link kernel: ata1: SError: { PHYRdyChg CommWake }
Apr 23 10:21:43 link kernel: ata1.00: failed command: WRITE DMA
Apr 23 10:21:43 link kernel: ata1.00: cmd ca/00:08:60:5d:cd/00:00:00:00:00/e1 tag 9 dma 4096 out
res 50/01:01:01:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Apr 23 10:21:43 link kernel: ata1.00: status: { DRDY }
Apr 23 10:21:43 link kernel: ata1.00: error: { AMNF }
Apr 23 10:21:43 link kernel: ata1: hard resetting link
Apr 23 10:21:43 link kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
Apr 23 10:21:43 link kernel: ata1.00: configured for UDMA/133
Apr 23 10:21:43 link kernel: ata1: EH complete
These go away when switching from med_power_with_dipm to medium_power.
This is somewhat weird as the PM830 datasheet explicitly mentions DIPM
being supported and the idle power-consumption is specified with DIPM
enabled.
There are many OEM customized firmware versions for the PM830, so for now
lets assume this is firmware version specific and blacklist LPM based on
the firmware version.
Cc: Kevin Shanahan <kevin@shanahan.id.au>
Reported-by: Kevin Shanahan <kevin@shanahan.id.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is an issue(Errata Ref#226) that the SATA can not be
detected via SATA Port-MultiPlayer(PMP) with following
error log:
ata1.15: PMP product ID mismatch
ata1.15: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata1.15: Port Multiplier vendor mismatch '0x1b4b'!='0x0'
ata1.15: PMP revalidation failed (errno=-19)
After debugging, the reason is found that the value Port-x
FIS-based Switching Control(PxFBS@0x40) become wrong.
According to design, the bits[11:8, 0] of register PxFBS
are cleared when Port Command and Status (0x18) bit[0]
changes its value from 1 to 0, i.e. falling edge of Port
Command and Status bit[0] sends PULSE that resets PxFBS
bits[11:8; 0].
So it needs a mvebu SATA WA to save the port PxFBS register
before PxCMD ST write and restore it afterwards.
This patch implements the WA in a separate function of
ahci_mvebu_stop_engine to override ahci_stop_gngine.
Signed-off-by: Evan Wang <xswang@marvell.com>
Cc: Ofer Heifetz <oferh@marvell.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Marvell armada37xx, armada7k and armada8k share the same
AHCI sata controller IP, and currently there is an issue
(Errata Ref#226)that the SATA can not be detected via SATA
Port-MultiPlayer(PMP). After debugging, the reason is
found that the value of Port-x FIS-based Switching Control
(PxFBS@0x40) became wrong.
According to design, the bits[11:8, 0] of register PxFBS
are cleared when Port Command and Status (0x18) bit[0]
changes its value from 1 to 0, i.e. falling edge of Port
Command and Status bit[0] sends PULSE that resets PxFBS
bits[11:8; 0].
So it needs save the port PxFBS register before PxCMD
ST write and restore the port PxFBS register afterwards
in ahci_stop_engine().
This commit allows drivers to override ahci_stop_engine
behavior for use by the Marvell AHCI driver(and potentially
other drivers in the future).
Signed-off-by: Evan Wang <xswang@marvell.com>
Cc: Ofer Heifetz <oferh@marvell.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit f0f56716fc.
According to Thierry's view,
https://www.spinics.net/lists/linux-ide/msg55357.html
some hardware-specific drivers already use their own resets,
and the common reset might make a path to occur double controls of resets.
For now, revert the commit that adds reset control support to ahci-platform,
and hold until the solution is confirmed not be affect all hardware-specific
drivers.
Fixes: f0f56716fc ("ata: ahci-platform: add reset control support")
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting.
The biggest change is refcnting fix for ata_host - the bug is recent
and can only be triggered on controller hotplug, so very few are
hitting it.
There also are a number of trivial license / error message changes and
some hardware specific changes"
* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
ahci: imx: add the imx8qm ahci sata support
libata: ensure host is free'd on error exit paths
ata: ahci-platform: add reset control support
ahci: imx: fix the build warning
ata: add Amiga Gayle PATA controller driver
ahci: imx: add the imx6qp ahci sata support
ata: change Tegra124 to Tegra
ata: ahci_tegra: Add AHCI support for Tegra210
ata: ahci_tegra: disable DIPM
ata: ahci_tegra: disable devslp for Tegra124
ata: ahci_tegra: initialize regulators from soc struct
ata: ahci_tegra: Update initialization sequence
dt-bindings: Tegra210: add binding documentation
libata: add refcounting to ata_host
pata_bk3710: clarify license version and use SPDX header
pata_falcon: clarify license version and use SPDX header
pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command()
pata_macio: Delete an error message for a failed memory allocation in two functions
pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe()
sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJaw8noAAoJEL1qUBy3i3wmZ/wP/RBzogQV0YhZeMJO4B/w/QaE
OJCAOJYd28dWwm6/aTkicAj1mf/WUnp9q5n7xvUOU56+cK3gqjD0cvTkIX4/T9bK
TnT4kJgIx1FibvqSAIxSfpawH8U7bO7peWTqSRAVtlT0UerNk8rBOFXOaThPg/Px
YRISOixexlIYWcGPdQiG00pr0Lwk8jr/ZLvx5FXpzwL89S25g7GZJatNTKIjAcau
WF1EBWMh7lIuiTQ5aWCXK+X9jGNSfzIMsHaANMBuTIo2dCPcBPKfT/eO8YVOHL1G
6jsvIwUinhmOFgo17CpQcqLxidyqMyNEpKxycNzwx2/CkjYIxkeQnQUG+UCawpZF
gb6OhAFJeitVh9kIxKxxwUSYhhL3RP10XxUxhX8imbPPf7F5llWTPdYUe5PMeXeQ
mqc37+YIqaZ88IGoVdxODPVaZCGXw9r5wAmc0yLQlzC68gp0G6vmIo29t64DKcOL
xKF5elBspm9bfLymzvHoVJsnErLMCbxY/fzAFpD32oGdJ/1UGoA4y29dMjaPazPr
cab7d+FYQSzMfiT9A3iIbwSh5luGjxSyzXr+awdBp6OujgqlFNkqYhWC0nSo0Jy7
To1RKASA37w/kCrNsdDXZOZuA8HQKve43JPF7LgFcUQvMHbhurZ9XsscyTNvSWLV
4nngEMtDNtmeXIfbNLNk
=2js3
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- add driver for Mellanox regmap LEDs
Improvement to ledtrig-disk:
- extend disk trigger for reads and writes
Improvements and fixes to existing LED class drivers:
- add more product/board names for PC Engines APU2
- fix wrong dmi_match on PC Engines APU LEDs
- clarify chips supported by LM355x driver
- fix Kconfig text for MLXCPLD, SYSCON, MC13783, NETXBIG
- allow leds-mlxcpld compilation for 32 bit arch"
* tag 'leds_for_4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: Fix wrong dmi_match on PC Engines APU LEDs
leds: Extends disk trigger for reads and writes
leds: Add more product/board names for PC Engines APU2
leds: add driver for support Mellanox regmap LEDs for BMC and x86 platform
leds: fix Kconfig text for MLXCPLD, SYSCON, MC13783, NETXBIG
leds: Clarify supported chips by LM355x driver
leds: leds-mlxcpld: Allow compilation for 32 bit arch
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
- There are three PHY lanes on iMX8QM, and can be
used in the following three cases
1. a two lanes PCIE_A, and a single lane SATA.
2. a single lane PCIE_A, a single lane PCIE_B
and a single lane SATA.
3. a two lanes PCIE_A, and a single lane PCIE_B.
The configuration of the iMX8QM AHCI SATA is relied
on the usage of PCIE ports in the case 1 and 2.
Use standalone iMX8 AHCI SATA probe and enable
functions to enable iMX8QM AHCI SATA support.
- To save power consumption, PHY CLKs can be gated
off after the configurations are done.
- The impedance ratio should be configured refer to
differnet REXT values.
0x6c <--> REXT value is 85Ohms
0x80 (default value) <--> REXT value is 100Ohms.
In general, REXT value should be 85ohms in standalone
PCIE HW board design, and 100ohms in SATA standalone
HW board design.
When the PCIE and the SATA are enabled simultaneously
in the HW board design. The REXT value would be set
to 85ohms.
Configure the SATA PHY impedance ratio to 0x6c in
default.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The host structure is not being kfree'd on two error exit paths
leading to memory leaks. Add in new err_free label and kfree host.
Detected by CoverityScan, CID#1466103 ("Resource leak")
Fixes: 2623c7a5f2 ("libata: add refcounting to ata_host")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support to get and control a list of resets for the device
as optional and shared. These resets must be kept de-asserted until
the device is enabled.
This is specified as shared because some SoCs like UniPhier series
have common reset controls with all ahci controller instances.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The blackfin architecture is getting removed, so this driver
is obsolete as well.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the default as the last entry to fix the following
build warning introduced by commit.
e5878732a5 ("ahci: imx: add the imx6qp ahci sata support")
drivers/ata/ahci_imx.c: In function 'imx_sata_disable':
drivers/ata/ahci_imx.c:478:2: warning: enumeration value 'AHCI_IMX53'
not handled in switch [-Wswitch]
switch (imxpriv->type) {
^~~~~~
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When commit 9c7be59fc5 ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc5 ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB...")
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There have been reports of the Crucial M500 480GB model not working
with LPM set to min_power / med_power_with_dipm level.
It has not been tested with medium_power, but that typically has no
measurable power-savings.
Note the reporters Crucial_CT480M500SSD3 has a firmware version of MU03
and there is a MU05 update available, but that update does not mention any
LPM fixes in its changelog, so the quirk matches all firmware versions.
In my experience the LPM problems with (older) Crucial SSDs seem to be
limited to higher capacity versions of the SSDs (different firmware?),
so this commit adds a NOLPM quirk for the 480 and 960GB versions of the
M500, to avoid LPM causing issues with these SSDs.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add Amiga Gayle PATA controller driver. It enables libata support
for the on-board IDE interfaces on some Amiga models (A600, A1200,
A4000 and A4000T) and also for IDE interfaces on the Zorro expansion
bus (M-Tech E-Matrix 530 expansion card).
Thanks to John Paul Adrian Glaubitz and Michael Schmitz for help
with testing the driver.
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- Regarding to imx6q ahci sata, imx6qp ahci sata
has the reset mechanism. Add the imx6qp ahci sata
support in this commit.
- Use the specific reset callback for imx53 sata,
and use the default ahci_ops.softreset for the others.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the AHCI-compliant Serial ATA host controller on the
Tegra210 system-on-chip.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tegra does not support DIPM and it should be disabled.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tegra124 does not support devslp and it should be disabled.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Get the regulator names to be initialized from soc structure
and initialize them.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Samsung explicitly states that queued TRIM is supported for Linux with
860 PRO and 860 EVO.
Make the previous blacklist to cover only 840 and 850 series.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
After commit 9a6d6a2dda ("ata: make ata port as parent device of scsi
host") manual driver unbind/remove causes use-after-free.
Unbind unconditionally invokes devres_release_all() which calls
ata_host_release() and frees ata_host/ata_port memory while it is still
being referenced as a parent of SCSI host. When SCSI host is finally
released scsi_host_dev_release() calls put_device(parent) and accesses
freed ata_port memory.
Add reference counting to make sure that ata_host lives long enough.
Bug report: https://lkml.org/lkml/2017/11/1/945
Fixes: 9a6d6a2dda ("ata: make ata port as parent device of scsi host")
Cc: Tejun Heo <tj@kernel.org>
Cc: Lin Ming <minggr@gmail.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds two new disk triggers for triggering on reads
and writes respectively, named "disk-read" and "disk-write".
The use case comes from working on the D-Link DNS-313 NAS
box. This features an RGB LED for disk activity. with
these two triggers I can couple the green LED to read
activity and the red LED to write activity, which gives
the appropriate user feedback about what is happening
on the disk. When tested it gave exactly the feedback
desired.
The in-kernel interface is simply changed to pass a bool
indicating if the activity is write activity and update
each trigger (and the composite "disk-activity" trigger)
depending on what is passed in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Like the Highpoint Rocketraid 642L and cards using a Marvel 88SE9235
controller in general, this RAID card also supports AHCI mode and short
of a custom driver, this is the only way to make it work under Linux.
Note that even though the card is called to 644L, it has a product-id
of 0x0645.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
- clarify license version (it should be GPL 2.0)
- use SPDX header
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We've got a kernel panic when using sata disk with sas controller:
[115946.152283] Unable to handle kernel NULL pointer dereference at virtual address 000007d8
[115946.223963] CPU: 0 PID: 22175 Comm: kworker/0:1 Tainted: G W OEL 4.14.0 #1
[115946.232925] Workqueue: events ata_scsi_hotplug
[115946.237938] task: ffff8021ee50b180 task.stack: ffff00000d5d0000
[115946.244717] PC is at sas_find_dev_by_rphy+0x44/0x114
[115946.250224] LR is at sas_find_dev_by_rphy+0x3c/0x114
......
[115946.355701] Process kworker/0:1 (pid: 22175, stack limit = 0xffff00000d5d0000)
[115946.363369] Call trace:
[115946.456356] [<ffff000008878a9c>] sas_find_dev_by_rphy+0x44/0x114
[115946.462908] [<ffff000008878b8c>] sas_target_alloc+0x20/0x5c
[115946.469408] [<ffff00000885a31c>] scsi_alloc_target+0x250/0x308
[115946.475781] [<ffff00000885ba30>] __scsi_add_device+0xb0/0x154
[115946.481991] [<ffff0000088b520c>] ata_scsi_scan_host+0x180/0x218
[115946.488367] [<ffff0000088b53d8>] ata_scsi_hotplug+0xb0/0xcc
[115946.494801] [<ffff0000080ebd70>] process_one_work+0x144/0x390
[115946.501115] [<ffff0000080ec100>] worker_thread+0x144/0x418
[115946.507093] [<ffff0000080f2c98>] kthread+0x10c/0x138
[115946.512792] [<ffff0000080855dc>] ret_from_fork+0x10/0x18
We found that Ding Xiang has reported a similar bug before:
https://patchwork.kernel.org/patch/9179817/
And this bug still exists in mainline. Since libsas handles hotplug and
device adding/removing itself, do not need to schedule ata hot plug task
here if it is a sas host.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Cc: Ding Xiang <dingxiang@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
After Laptop Mode Tools starts to use min_power for LPM, a user found
out Crucial BX100 SSD can't get mounted.
Crucial BX100 SSD 500GB drive don't work well with min_power. This also
happens to med_power_with_dipm.
So let's disable LPM for Crucial BX100 SSD 500GB drive.
BugLink: https://bugs.launchpad.net/bugs/1726930
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Various people have reported the Crucial MX100 512GB model not working
with LPM set to min_power. I've now received a report that it also does
not work with the new med_power_with_dipm level.
It does work with medium_power, but that has no measurable power-savings
and given the amount of people being bitten by the other levels not
working, this commit just disables LPM altogether.
Note all reporters of this have either the 512GB model (max capacity), or
are not specifying their SSD's size. So for now this quirk assumes this is
a problem with the 512GB model only.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=89261
Buglink: https://github.com/linrunner/TLP/issues/84
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The local variable "ret" will eventually be set to an appropriate value
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Because power of Salvator-X board is cut off in suspend,
it needs to reset SATA PHY state in resume.
Otherwise, SATA partition could not be accessed anymore.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
[reinit phy in sata_rcar_resume() function on R-Car Gen3 only]
[factor out SATA module init sequence]
[fixed the prefix for the subject]
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
syzkaller hit a WARN() in ata_bmdma_qc_issue() when writing to /dev/sg0.
This happened because it issued an ATA pass-through command (ATA_16)
where the protocol field indicated that NCQ should be used -- but the
device did not support NCQ.
We could just remove the WARN() from libata-sff.c, but the real problem
seems to be that the SCSI -> ATA translation code passes through NCQ
commands without verifying that the device actually supports NCQ.
Fix this by adding the appropriate check to ata_scsi_pass_thru().
Here's reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[53] = { 0 };
buf[36] = 0x85; /* ATA_16 */
buf[37] = (12 << 1); /* FPDMA */
buf[38] = 0x1; /* Has data */
buf[51] = 0xC8; /* ATA_CMD_READ */
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: ee7fb331c3 ("libata: add support for NCQ commands for SG interface")
Reported-by: syzbot+2f69ca28df61bdfc77cd36af2e789850355a221e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
syzkaller hit a WARN() in ata_qc_issue() when writing to /dev/sg0. This
happened because it issued a READ_6 command with no data buffer.
Just remove the WARN(), as it doesn't appear indicate a kernel bug. The
expected behavior is to fail the command, which the code does.
Here's a reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[42] = { [36] = 0x8 /* READ_6 */ };
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: f92a26365a ("libata: change ATA_QCFLAG_DMAMAP semantics")
Reported-by: syzbot+f7b556d1766502a69d85071d2ff08bd87be53d0f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
