Otherwise we may instantiate and hence have something try to access the
device while it is still completing initialisation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver core does this and it's never legal to rely on the value of
drvdata if not set in probe() anyway.
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* APIs are device managed and make code simpler.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
"idx" is controled by the user and can be a negative offset into the
input_names[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no need to have versioning beyond that for the kernel, especially
when the version number never gets updated.
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 12 pins that can be configured depending on the system
configuration. Allow settting the corresponding registers from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware I/O has to be open-coded due to registers of unequal sizes.
Other than that, the transition is straight forward.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip needs a new download after each reset, so the code to do that
needs to live in adau1701_reset().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two muxes, one for connecting I2S inputs to internal
channels, and another one for selecting which internal channel should
be routed to which PWM output pin.
This patch adds DAPM widgets and routes for this driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add register definitions for input and output mux registers, and rewrite
the tas5086_accessible_reg() function.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support registers of unequal sizes, the I2C I/O has to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As some of ALC269 quirks use the inverted dmic feature, we need to
call alc_inv_dmic_sync() in the resume callback like in alc_resume(),
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The stac_resume() is exactly what the default resume code does, so
we don't have to define and use it doubly. Let's cut it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is a cleanup to the previous patch "reset hda link during system/
runtime suspend".
In this patch
- azx_enter_link_reset() and azx_exit_link_reset() are defined for entering and
exiting the link reset respectively. azx_link_reset() is no longer used and
replaced by azx_enter_link_reset().
- azx_reset() reuses the above two new functions for a link reset cycle
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin's connection list may change dynamically with hot-plug event
on Intel Haswell chip. Users would see connections be "0" in codec#.
when play audio on this pin, software driver choose converter from cache
connections. So add "In-driver connection" info to avoid confuse when
raw connections are different with cache connection.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got bug report wrt many machines with VT1708 (e.g. IBM POS
machines) showing the broken auto-mute behavior. It turned out that
the problem is that the pin control values of the speaker and line-out
pins are completely ignored. As a workaround, let's use the newly
introduced feature of the generic parser, to control the mute via amp
on pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag, auto_mute_via_amp, to determine the behavior of the
headphone / line-out auto-mute. When this flag is set, the generic
driver mutes the speaker and line outputs via the amp mute of each
pin, instead of changing the pin control values.
This is introduced for devices that don't work expectedly with the pin
control values; for example, some devices are known to keep enabling
the speaker outputs no matter which pin control values are set on the
speaker pins.
The driver doesn't check actually whether the pins have the output amp
caps, but assumes that the proper mixer (mute) controls are created on
all these pins. If not the case, you can't use this flag for your
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To reduce pop noise during playback stream start and stop the codec needs
to have the digital_mute callback implemented.
The codec need to be muted before the CPU dai has been stopped (McPDM).
Stopping the McPDM will generate a pop on the codec since no signal on the
PDM bus means full negative amplitude.
By managing the mute/unmute state of the outputs we can decrease the amount
of pop noise when playback starts or stops.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to free the irq at twl6040_remove() which is called when the machine
driver has been removed (the card has been removed).
If we fail to do that, next time when the machine driver is loaded the
codec's probe will fail since the irq has been already requested.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce a new helper function, snd_ctl_sync_vmaster(), which updates
the slave put callbacks forcibly as well as calling the hook. This
will be used in the upcoming patch in HD-audio codec driver for
toggling the mute in vmaster slaves.
Along with the new function, the old snd_ctl_sync_vmaster_hook() is
replaced as a macro calling with the argument hook_only=true.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If all the codecs report ClkStopOK (OK to stop bus clock) after being put to
D3, this patch will reset the HDA link before the controller is put to D3.
So the link will be in reset during system or runtime suspend, the bus clock
stops and the codecs are in D3(ClkStop) state.
This may help to reduce power consumption by dozens of mW on some peripheral
hda codecs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the leftover CONFIG_SND_SOC_OMAP_HDMI_CODEC in
sound/soc/omap/Kconfig with CONFIG_SND_SOC_HDMI_CODEC, which was
forgotten in the commit bf7c6e6c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWf9
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.11
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
In sound/usb/card.c and sound/usb/misc/ua101.c there are no spaces
between the vendor and the device names, use this style in the other
drivers too.
This also helps keeping consistency when new drivers copies from the
ones already in the mainline tree.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_card_used variable is only read but never written, remove it.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code is older than git, and I haven't tested it, but if size ==
SIZE_MAX_STATUS then we would write one space past the end of the
rmh->Stat[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BH9M
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Like the X220, this quirk was added to support docking station,
so enable the fixup instead.
According to Jan, the generic parser works equal or better
than the current parser. This was tested under a 3.9 kernel.
Reported-by: Jan Alexander Steffens <jan.steffens@gmail.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some VIA codecs like VT1708S have Mic boost amps in the mic pins but
they aren't exposed in the capability bits. In the past driver code,
we override the pin caps and create mic boost controls forcibly.
While transition to the generic parser, we lost the mic boost controls
although the pin caps are still overridden, because the generic parser
code checks the widget caps, too.
So this patch adds a new helper function to allow the override of the
given widget capability bits, and makes VIA codecs driver to add the
missing input-amp capability bit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59861
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell HDMI codecs, the pins choose converter 0 by default.
This would cause conflict when playing audio on unused pins,the pin with
physical device connected would get audio data too.
i.e. Pin 0/1/2 default choose converter 0, pin 1 has HDMI monitor connected.
when play audio on Pin 0 or pin 2, pin 1 could get audio data too.
This patch configure unused pins to choose different converter.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a selection to a converter MUX is changed in hdmi_pcm_open(), it
should be cached so that the given connection can be restored properly
at PM resume. We need just to replace the corresponding
snd_hda_codec_write() call with snd_hda_codec_write_cache().
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return -ENOMEM in the kmalloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell converters maybe in wrong power state before usage.
i.e. only converter 0 is in D0, converter 1/2 are in D3.
When pin choose converter 1/2, there's no audio output, this
cause dependency when playing differnt stream on pins.
AUD_PWRST ConvertorA_Widget_Power_State_Current D0
AUD_PWRST ConvertorA_Widget_Power_State_Requsted D0
AUD_PWRST ConvertorB_Widget_Power_State_Current D3
AUD_PWRST ConvertorB_Widget_Power_State_Requested D3
AUD_PWRST ConvC_Widget_PwrSt_Curr D3
AUD_PWRST ConvC_Widget_PwrSt_Req D3
This patch check converter's power state and set D0 if it's in D3 mode.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The refactoring by commit 9040d102 introduced the new function
snd_hda_check_power_state(). This function is supposed to return true
if the state already reached to the target state, but it actually
returns false for that. An utterly stupid typo while copy & paste.
Fortunately this didn't influence on much behavior because powering up
AFG usually powers up the child widgets, too. But the finer power
control must have been broken by this bug.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
devm_request_mem_region is called in devm_ioremap_resource(). Hence that
part can also be removed.
Since devm_ioremap_resource prints error message on failure, there is
no need to print an explicit warning message.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: alsa-devel@alsa-project.org
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
These headset jacks keep coming in on more and more platforms, and
it's possible I don't catch them all. Make it easier to test and
verify by making models.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sffsdr machine support does not build since at least v2.6.36
(~3 years). There is little hope of it being fixed, so remove
the support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
* for-linus: (635 commits)
ALSA: usb-audio: Fix invalid volume resolution for Logitech HD Webcam c310
ALSA: hda - Fix pin configurations for MacBook Air 4,2
ALSA: usb-audio: work around Android accessory firmware bug
ALSA: hda - Headset mic support for three more machines
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
...
Just like the previous fix for LogitechHD Webcam c270 in commit
11e7064f35, c310 model also requires the
same workaround for avoiding the kernel warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59741
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 4,2 requires the whole default pin configuration table to
be overridden by the driver, as usual, as Apple's machines don't set
up properly after boot. Otherwise mic won't work, and other ill
effect may happen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59381
Reported-and-tested-by: Peter John Hartman <peterjohnhartman@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Android firmware enables the audio interfaces in accessory
mode, it always declares in the control interface's baInterfaceNr array
that interfaces 0 and 1 belong to the audio function. However, the
accessory interface itself, if also enabled, already is at index 0 and
shifts the actual audio interface numbers to 1 and 2, which prevents the
PCM streaming interface from being seen by the host driver.
To get the PCM interface interface to work, detect when the descriptors
point to the (for this driver useless) accessory interface, and redirect
to the correct one.
Reported-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Tested-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They need these quirks to have headset mic support.
BugLink: https://bugs.launchpad.net/bugs/1189363
Tested-by: Shawn Wang <shawn.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull VFS fixes from Al Viro:
"Several fixes + obvious cleanup (you've missed a couple of open-coded
can_lookup() back then)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
ncpfs: fix rmdir returns Device or resource busy
support for the DMA40. Now with MUSB and some platform
data removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=rn7t
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
Reported-by: Dennis May <dennis.may@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.
The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.
According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The individual component drivers are only useful with a machine driver and
should be selected by the machine drivers so shouldn't have help text of
their own in order to hide them in interactive configuration.
Signed-off-by: Mark Brown <broonie@linaro.org>
In struct snd_soc_card zylonite .owner is assigned THIS_MODULE
twice, remove one of them.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also fix return values for headphone switch updates.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This fixes:
975:9: sparse: Using plain integer as NULL pointer
1917:24: sparse: symbol 'rt5640_aif_dai_ops' was not declared. Should it be static?
1924:27: sparse: symbol 'rt5640_dai' was not declared. Should it be static?
2079:19: sparse: symbol 'rt5640_i2c_driver' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch that resulted in
bfcc74e (ASoC: SPEAr spdif_{in,out}: use devm for clk and a few
more cleanups)
was broken and applied on a newer tree than it was created for. So
bfcc74e introduced unbalanced clk handling, two warnings about unused
variables and passed 3 arguments to a function only taking 2. This
commit fixes that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Initially, this binding and driver only describe/support playback to
headphones and speakers.
This driver will support Beaver and Dalmore.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Modify the RT5640 driver to parse platform data from device tree. Write
a DT binding document to describe those properties.
Slight re-ordering of rt5640_i2c_probe() to better fit the DT parsing.
Since ldo1_en is optional, guard usage of it with gpio_is_valid(), rather
than open-coding an if (gpio) check.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain use cases may require specific DRE settings so expose control
of these.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Implement a DMA slave config prepare routine, as until now the MSP
driver depended on the DMA controller completing the channel
configuration on its own, but this is not the case anymore since the
recent DMA driver updates.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a field with the tx/rx register address to the DMA parameters
structure, and set it to the correct address during device
initialization.
This address used to be hardcoded in the DMA controller driver, it now
needs to be explicitly figured out by the device driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move struct ux500_msp_dma_params declaration from ux500_msp_i2s_drvdata
to ux500_msp, this saves some confusing pointer passing and allows to
access all DMA configuration fields from ux500_msp_i2s.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Kconfig and Makefile to support SPEAr Audio driver.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some runtime-determined constraints might need to be satisfied prior to
firmware loading, so the actual download and releasing the device from
reset has to be postponed. Factor it out first, so we have everything at
one place.
This also changes the behaviour in a way that adau1701_i2c_probe() will
assert the reset line, and wait for the codec probe to release it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise, ssm2518_set_tdm_slot() always returns error if slots != 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the initial imx-wm8962 device-tree-only machine driver working with
fsl_ssi driver. More features can be added on top of it later.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
