The X1000's AIC is similar to the AIC found on other Ingenic SoCs.
It has symmetric playback/capture rates like the JZ4740, but more
flexible clocking when outputting the system or bit clocks.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509124238.195191-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.
The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.
Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.
Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
.set_sysclk() is effectively unused here. No machine drivers use
jz4740-i2s; and JZ4740_I2S_CLKSRC_EXT is the only selectable clock
source with simple-card, but that is also the default source and
has a fixed frequency, so configuring it would be redundant.
simple-card ignores -ENOTSUPP error codes when setting the sysclock,
so any device trees that do set the sysclock for some reason should
still work.
It's still possible to configure the clock parent manually in the
device tree and control frequency using other simple-card options,
so at the end of the day there's no real loss in functionality.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221028103418.17578-4-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move most of the DAI probe/remove logic into component ops.
This makes things more consistent because the AIC clock is
now managed solely from the component side. And it makes it
easier to add codec switching support later on.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-10-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the component suspend/resume functions near the definition
of the component driver to emphasize that they're unrelated to
the DAI functions.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-9-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S controller on JZ47xx SoCs doesn't impose restrictions on
sample rate and the driver doesn't make any assumptions about it,
so the DAI should advertise a continuous sample rate range.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-8-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio controller on JZ47xx SoCs can transfer 20- and 24-bit
samples in the FIFO, so allow those formats to be used with the
I2S driver. Although the FIFO doesn't care about the in-memory
sample format, we only support 4-byte format variants because the
DMA controller on these SoCs cannot transfer in 3-byte multiples.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-7-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some purely cosmetic changes: line up all the macro values to
make things easier to read and sort the includes alphabetically.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-6-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Get rid of a couple of macros and improve readability by using
FIELD_PREP() and GENMASK() for the sample size setting.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-5-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The differences between register fields on different SoC versions
can be abstracted away using the regmap field API. This is easier
to understand and extend than comparisons based on the version ID.
Since the version IDs are unused after this change, remove them at
the same time, and remove unused macros.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-4-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap for accessing the AIC registers makes the driver a
little easier to read, and later refactors can take advantage of
regmap APIs to further simplify the driver.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the JZ4740, there is a single bit that flushes (empties) both
the transmit and receive FIFO. Later SoCs have independent flush
bits for each FIFO.
Independent FIFOs can be flushed before the snd_soc_dai_active()
check because it won't disturb other active streams. This ensures
that the FIFO we're about to use is always flushed before starting
up. With shared FIFOs we can't do that because if another substream
is active, flushing its FIFO would cause underrun errors.
This also fixes a bug: since we were only setting the JZ4740's
flush bit, which corresponds to the TX FIFO flush bit on other
SoCs, other SoCs were not having their RX FIFO flushed at all.
Fixes: 967beb2e87 ("ASoC: jz4740: Add jz4780 support")
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20221023143328.160866-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This isn't used and doesn't need to be in the private data struct.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220708160244.21933-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's simpler to set up the playback and capture DMA settings
at driver probe time instead of during DAI probing.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220706211330.120198-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver doesn't require Open Firmware support. Remove the
OF-specific includes and drop the Kconfig dependency.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220706211330.120198-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the legacy DAI naming flag from opting in to the new scheme
(non_legacy_dai_naming), to opting out of it (legacy_dai_naming).
This driver appears to be on the CPU side of the DAI link and
currently uses the legacy naming, so add the new flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-7-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the core has been migrated across to the new direct clock
specification we can move the drivers back to the normal set_fmt
callback.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220519154318.2153729-40-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of updating the core to directly tell drivers if they are clock
provider or consumer update this CPU side driver to use the new direct
callback.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220519154318.2153729-13-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Delete unused define of JZ4740_I2S_BIT_CLK, because it is unused
in any files.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210506131833.27420-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
jz4740_i2s_set_sysclk() does not check the return values of clk_get(),
while the file dereferences the pointers in clk_put().
Add the missed checks to fix it.
Fixes: 11bd3dd1b7 ("ASoC: Add JZ4740 ASoC support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20201203144227.418194-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All platforms that use the jz4740-i2s driver have been switched to
devicetree for a while now and the assignment of the DMA peripheral ID
is done in the devicetree.
It is no longer necessary to manually assign the peripheral ID in the
driver, so remove that. The DMA driver does not even look at the value
assigned in the driver anymore and always uses the value provided by the
devicetree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201023092346.5777-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
All boards with Ingenic SoCs probe with devicetree already, we have no
use for a non-devicetree path.
This solves some compilation warnings that were caused by unused
variables in the case where CONFIG_OF was disabled.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200523125455.12392-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
We have snd_soc_dai/dai_stream/component_active() macro
This patch uses it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87sgg258io.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before the JZ4770, the playback and capture sampling rates had to match.
The JZ4770 supports independent sampling rates for both.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200306222931.39664-6-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The change of offset for the {rx,tx}_threshold fields in the conf
register predates the JZ4780, and was first introduced in the JZ4760.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200306222931.39664-5-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing an enum as match data, and checking its value in the
probe to register one or the other dai, pass a pointer to a struct
i2s_soc_info, which contains all the information relative to one SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200306222931.39664-4-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the code cleaner by using a "struct device *dev" variable instead
of dereferencing it everytime from within the struct platform_device.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200306222931.39664-3-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.
Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.
This patch moves DAI driver .suspend/.resume to Component driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878sm3ym4j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit 67ad656bdd ("ASoC: jz4740: Use
of_device_get_match_data()"), the match local variable is unused and the
compiler rightly warns.
sound/soc/jz4740/jz4740-i2s.c: In function 'jz4740_i2s_dev_probe':
sound/soc/jz4740/jz4740-i2s.c:500:29: warning: unused variable 'match' [-Wunused-variable]
500 | const struct of_device_id *match;
Drop it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <alsa-devel@alsa-project.org>
Fixes: 67ad656bdd ("ASoC: jz4740: Use of_device_get_match_data()")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191008235212.228856-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This probe function is only called if the device is backed by a DT node,
so switch this call to of_device_get_match_data() to reduce code size
and simplify a bit. This also avoids needing to reference a potentially
undefined variable because of_device_get_match_data() doesn't need to
know anything beyond the struct device to find the match table.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <alsa-devel@alsa-project.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191004214334.149976-8-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The board now uses the simple-audio-card driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 675 mass ave cambridge
ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204654.276825629@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on MACH_JZ4740 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jz4780 and jz4740 have very similar i2s blocks.
The slight difference is in Rx/Tx fifos.
And the bitclocks for input/output are different.
This patch adds jz4780 support to the driver
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds device tree support for the jz4740 driver.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
