There is currently no return check for writing an authentication
type (HERMES_AUTH_SHARED_KEY or HERMES_AUTH_OPEN). It looks like
it was accidentally skipped.
This patch adds a return check similar to the other checks in
__orinoco_hw_setup_enc() for hermes_write_wordrec().
Detected using the static analysis tool - Svace.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221227133306.201356-1-aleksei.kodanev@bell-sw.com
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215197
Fixes: e542e66b7c ("rtl8xxxu: add bluetooth co-existence support for single antenna")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/03b099c1-c671-d252-36f4-57b70d721f9d@gmail.com
The configurations, wde_qempty_acq_num and wde_qempty_mgq_sel, are used
when MAC checks if TX queues are empty. Fill the corresponding setting
for 8852B.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-5-pkshih@realtek.com
TX BD's RAM table describes how HW allocates usable buffer section
for each TX channel at fetch time. The total RAM size for TX BD is
chip-dependent. For 8852BE, it has only half size (32) for TX channels
of single band. Original table arrange total size (64) for dual band.
It will overflow on 8852BE circuit and cause section conflicts between
different TX channels.
So, we do the changes below.
* add another table for single band chip and export both kind of tables
* point to the expected one in rtw89_pci_info by chip
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-4-pkshih@realtek.com
Some hardware modules don't have good RF characteristic as regular.
It could get ADC abnormal in low temperature, and it causes bad RX
performance and affects calibration result of DPK.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-3-pkshih@realtek.com
This change fixes the precision of CFO and TX EVM, and it could imporve
performance in some cases. Also, use the correctted definition for 8852A.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-2-pkshih@realtek.com
The mac_id of management frames should follow rtwvif->mac_id or
rtwsta->mac_id. Add this patch to set the correct mac_id and
prevent unexpected behavior.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-2-pkshih@realtek.com
When transmitting a packet that gets from ieee80211_nullfunc_get(),
the vif in tx_info->control was no assigned, which will cause
dereferencing a null pointer.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-1-pkshih@realtek.com
The Wi-Fi role info structure will need to H2C to firmware, firmware
need these information to do some multi-role operation. v1 add DBCC
and NOA information in the structure. And driver side also need to
put/get values at the corresponding version of structure.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-8-pkshih@realtek.com
RTL8852B support the new features like TDMA instant (Change TDMA mechanism
immediately), Co-RX feature (Wi-Fi/Bluetooth can RX in the same time) and
so on. The v1 TDMA policy will enable those newer mechanism. It will have
a better coexistence performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-7-pkshih@realtek.com
Because the difference of the hardware design, RTL8852C can not get the
PTA owner by the same method with RTL8852B, RTL8852A. Modify the get owner
API and related logic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-6-pkshih@realtek.com
Slot list is to list the WiFi/Bluetooth PTA hardware priority setting.
Move the list parser to its function, not to append together with TDMA
parser.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-5-pkshih@realtek.com
The report records the slots/events and their time cost about the code
call flow at firmware, ver 3 assign a reserved variable to recognize
the report is enabled or not. And add corresponding function to parsing
the report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-4-pkshih@realtek.com
Coexistence need to send Null data to stop AP keeps TX packet to DUT
before DUT coexistence switch to Bluetooth time slot, or it will be an
interference to DUT BT and because DUT will not RX packet from AP
the packet retry may harmful to WL TP. Compare to v1 version, the newer
firmware report will also report Null TX data counter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-3-pkshih@realtek.com
The newer Wi-Fi firmware are all changed to "Not to send H2C to
mention firmware how many call flow step should firmware trace".
The structure had removed the member, and define the steps number
at newer version firmware.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-2-pkshih@realtek.com
Add check for the return value of alloc_workqueue since it may return
NULL pointer.
Moreover, add destroy_workqueue when rtw89_load_firmware fails.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230104142901.1611-1-jiasheng@iscas.ac.cn
Do `kfree_skb(new)` before `goto out` to prevent potential leak.
Fixes: 8959077797 ("rtw89: 8852a: add ieee80211_ops::hw_scan")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103141054.17372-1-pkshih@realtek.com
Change style to feature version separate. And because there are
different WiFi roles number in the firmware, it will make structure
length longer or shorter, so update the length calculator to cover
the difference.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-8-pkshih@realtek.com
Only when firmware control report version is 1, need to get the counter by
reading the register. The other version will monitor the counter at
firmware. And upstream branch only RTL8852A has this old version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-7-pkshih@realtek.com
Comparing v5 control report to v4 version, v5 reduce some of variable's
size to reduce firmware code size. And change the grant signal report
format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-6-pkshih@realtek.com
The rtw89 driver may support more than 1 version of Wi-Fi firmware for
certain chips. In order to support all the firmware, change to select logic
by firmware feature version code. Type control version 4 will monitor
Bluetooth PTA hardware counters at firmware and C2H to driver, but
version 1 will not do this.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-5-pkshih@realtek.com
To support v4 version firmware cycle report, apply the related
structure and functions. v4 cycle report add a group of status
to show how the free-run/TDMA training goes to. It is a firmware
mechanism that can auto adjust coexistence mode between TDMA and
free run mechanism at 3 antenna solution.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-4-pkshih@realtek.com
Because there are new report format in the upcoming patches, to make the
logic more readable, rename the related structure by their version number.
And to support the several version at the same time, add union definition
to include all the versions.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-3-pkshih@realtek.com
There are at least 2 version of cycle report format. If the code keep
translating the report to local variable, the numbers of variable in
check btc report function will out of maximum variable numbers. And
most of these variable are using only one time, it is not necessary
to store at memory.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230103140238.15601-2-pkshih@realtek.com
Allow probing rfkill-gpio via device tree. This hooks up the already
existing support that was started in commit 262c91ee5e ("net:
rfkill: gpio: prepare for DT and ACPI support") via the "rfkill-gpio"
compatible, with the "name" and "type" properties renamed to "label"
and "radio-type", respectively, in the device tree case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20230102-rfkill-gpio-dt-v2-2-d1b83758c16d@pengutronix.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a device tree binding document for GPIO controlled rfkill switches.
The label and radio-type properties correspond to the name and type
properties used for ACPI, respectively. The shutdown-gpios property
is the same as defined for ACPI.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230102-rfkill-gpio-dt-v2-1-d1b83758c16d@pengutronix.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit acb99b9b2a ("mac80211: Add stations iterator
where the iterator function may sleep"). A different approach was found
for the rtw88 driver where most of the problematic locks were converted
to a driver-local mutex. Drop ieee80211_iterate_stations() because there
are no users of that function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221226191609.2934234-1-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150453.114742-1-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: f52b041aed ("libertas: Add spinlock to avoid race condition")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-5-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: d2e7b3425c ("libertas: disable functionality when interface is down")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-4-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: a3128feef6 ("libertas: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-3-yangyingliang@huawei.com
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: fc75122fab ("libertas_tf: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-2-yangyingliang@huawei.com
After the DMA buffer is mapped to a physical address, address is stored
in pktids in brcmf_msgbuf_alloc_pktid(). Then, pktids is parsed in
brcmf_msgbuf_get_pktid()/brcmf_msgbuf_release_array() to obtain physaddr
and later unmap the DMA buffer. But when count is always equal to
pktids->array_size, physaddr isn't stored in pktids and the DMA buffer
will not be unmapped anyway.
Fixes: 9a1bb60250 ("brcmfmac: Adding msgbuf protocol.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207013114.1748936-1-shaozhengchao@huawei.com
The brcmf_netdev_start_xmit() returns NETDEV_TX_OK without freeing skb
in case of pskb_expand_head() fails, add dev_kfree_skb() to fix it.
Compile tested only.
Fixes: 270a6c1f65 ("brcmfmac: rework headroom check in .start_xmit()")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1668684782-47422-1-git-send-email-zhangchangzhong@huawei.com
Fault injection test reports this issue:
kernel BUG at net/core/dev.c:10731!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
Call Trace:
<TASK>
wilc_netdev_ifc_init+0x19f/0x220 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_cfg80211_init+0x30c/0x380 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_bus_probe+0xad/0x2b0 [wilc1000_spi 1520a7539b6589cc6cde2ae826a523a33f8bacff]
spi_probe+0xe4/0x140
really_probe+0x17e/0x3f0
__driver_probe_device+0xe3/0x170
driver_probe_device+0x49/0x120
The root case here is alloc_ordered_workqueue() fails, but
cfg80211_unregister_netdevice() or unregister_netdev() not be called in
error handling path. To fix add unregister_netdev goto lable to add the
unregister operation in error handling path.
Fixes: 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1669289902-23639-1-git-send-email-wangyufen@huawei.com
In the error path of ipw_wdev_init(), exception value is returned, and
the memory applied for in the function is not released. Also the memory
is not released in ipw_pci_probe(). As a result, memory leakage occurs.
So memory release needs to be added to the error path of ipw_wdev_init().
Fixes: a3caa99e6c ("libipw: initiate cfg80211 API conversion (v2)")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209012422.182669-1-shaozhengchao@huawei.com
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called to free and drop the SKB when
it's reset, so replace it with dev_kfree_skb_irq(). Compile tested
only.
Fixes: 43f66a6ce8 ("Add ipw2200 wireless driver.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221208143826.2385218-1-yangyingliang@huawei.com
Fixing transmission failure which results in
"authentication with ... timed out". This can be
fixed by disable the REG_TXPAUSE.
Signed-off-by: Jun ASAKA <JunASAKA@zzy040330.moe>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217030659.12577-1-JunASAKA@zzy040330.moe
This chip is found in cheap USB devices from TP-Link, D-Link, etc.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
Chip versions older than "I cut" need software rate control. That will
be in the next commit. Until then MCS7 is used for all data frames.
The "I cut" chips are not supported. They require different firmware
and initialisation tables. Support can be added if someone has the
hardware to test it.
Co-developed-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Co-developed-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Co-developed-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3aad60f6-23f9-81e8-c741-4bd51e99f423@gmail.com
Define the constants CCK_AGC_RPT_LNA_IDX_MASK and
CCK_AGC_RPT_VGA_IDX_MASK instead of using the same literals
in four places.
And get the bits from cck_agc_rpt using u8_get_bits().
It's a cosmetic change only.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/cfe79922-efdf-2ed0-7404-263915d19d82@gmail.com
Every chip family except RTL8723AU has a copy of the efuse dumping
code. Remove this and dump the efuse from a single place using a new
function rtl8xxxu_dump_efuse().
Also, use print_hex_dump() to print the efuse instead of a loop and
dev_info(). It shows the ASCII interpretation of the bytes, which is
nice.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/2aa5200a-ee42-e064-16a1-672bed5708c6@gmail.com
Some hardware modules don't have good RF characteristic as regular.
It could have RF PA characteristic that current code doesn't handle
properly, and it runs into wrong DPK flow that doesn't complete DPK
resulting in bad EVM.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221216052939.9991-1-pkshih@realtek.com
