When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.
This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver calls phy_connect_direct and registers hclge_mac_adjust_link
to synchronize mac speed and duplex from phy. It is better to
synchronize mac speed and duplex from phy when phy link up.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our phy does not support 1000M/half, this patch removes 1000M/half from
PHY_SUPPORTED_FEATURES.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
coalesce param updates every 100 napi times, it may update a little
late if ping test after a high rate flow, may over napi poll is called
100 times as ping test sends packets every second.
This patch updates coalesce param every second, instead with every
100 napi times. It can not update the param 100% in time, but the
lag time is very short.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_nic_uninit_vector_data(), the procedure of uninitializing
the tqp_vector's IRQ has not set affinity_notify to NULL and changes
its init flag. This patch fixes it. And for simplificaton, local
variable tqp_vector is used instead of priv->tqp_vector[i].
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, it is unnecessary to get the hardware's default
configuration again, otherwise, the user's configuration will be
overwritten.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() completes successfully, it should update the
last_reset_time, set reset_fail_cnt to 0, and set reset_type of
hnae3_ae_dev to HNAE3_NONE_RESET.
Also when hclgevf_reset() completes successfully, it should update
the last_reset_time, and set reset_type of hnae3_ae_dev to
HNAE3_NONE_RESET.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN, the calling of napi_disable() may not return, since the
napi_complete() in the hns3_nic_common_poll() will never be called when
HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before
checking HNS3_NIC_STETE_DOWN.
Fixes: ff0699e04b ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hclgevf_pci_reset(), it only uninitialize and initialize
the msi, so if the initialization fails, hclgevf_uninit_hdev()
does not need to uninitialize the msi, but needs to uninitialize
the pci, otherwise it will cause pci resource not free.
Fixes: 862d969a3a ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_vector_ring_chain() failed in the
hns3_nic_init_vector_data(), it should do the error handling instead
of return directly.
Also, cur_chain should be freed instead of chain and head->next should
be set to NULL in error handling of hns3_get_vector_ring_chain.
This patch fixes them.
Fixes: 73b907a083 ("net: hns3: bugfix for buffer not free problem during resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a packet was decapsulated it is classified to the relevant FID
based on its VNI and undergoes L2 forwarding.
Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap
decapsulated ARP packets during L2 forwarding and instead can only trap
such packets in the underlay router during decapsulation.
Add this missing packet trap, which is required for VXLAN routing when
the MAC of the target host is not known.
Fixes: b02597d513 ("mlxsw: spectrum: Add NVE packet traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f43 ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved setting if_combination.num_different_channels/radar_detect_widths
into an else after use_chanctx. In the case of use_chanctx, these two
settings were getting overwritten.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the identifier used for indirect block callback registry and
for block rule cb registry (when done via indirect blocks) was the pointer
to the netdev we were interested in receiving updates on. This worked fine
if a single app existed that registered one callback per netdev of
interest. However, if multiple cards are in place and, in turn, multiple
apps, then each app may register the same callback with the same
identifier to both the netdev's indirect block cb list and to a block's cb
list. This can lead to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the app pointer as the identifier for
netdev indirect block cb registry, allowing each app to register a unique
callback per netdev. For block cb registry, the same app may register
multiple cbs to the same block if using TC shared blocks. Instead of the
app, use the pointer to the allocated cb_priv data as the identifier here.
This means that there can be a unique block callback for each app/netdev
combo.
Fixes: 3166dd07a9 ("nfp: flower: offload tunnel decap rules via indirect TC blocks")
Reported-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics which include RDMA counters are useful even when the
netdevice is down. Do not free the port statistics DMA buffers
when the netdevice is down. This is keep the snapshot of the port
statistics and counters will just continue counting when the
netdevice goes back up.
Split the bnxt_free_stats() function into 2 functions. The port
statistics buffers will only be freed when the netdevice is
removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down. Store a snapshot of the
rtnl_link_stats64 before shutdown. This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the code allows ETS bandwidth weight 0 to be set on unused TCs.
We should not set any DCB parameters on unused TCs at all.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the CoS counters as additional priority counters by looking up
the priority to CoS queue mapping. If the TX extended port statistics
block size returned by firmware is big enough to cover the CoS counters,
then we will display the new priority counters. We call firmware to get
the up-to-date pri2cos mapping to convert the CoS counters to
priority counters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some minor differences when assigning VF resources on the
new chips. The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing up a device, the code checks to see if the number of
MSIX has changed. pci_disable_msix() should be called first before
changing the number of reserved NQs/CMPL rings. This ensures that
the MSIX vectors associated with the NQs/CMPL rings are still
properly mapped when pci_disable_msix() masks the vectors.
This patch will prevent errors when RDMA support is added for the new
57500 chips. When the RDMA driver shuts down, the number of NQs is
decreased and we must use the new sequence to prevent MSIX errors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en requires same number of stat_ctxs as CP rings but RDMA
requires only 1 stat_ctx. Also add a new parameter resv_stat_ctxs
to better keep track of stat_ctxs reserved including resources used
by RDMA. Add a stat_ctxs parameter to all the relevant resource
reservation functions so we can reserve the correct number of
stat_ctxs.
Prior to this patch, we were not reserving the extra stat_ctx for
RDMA and RDMA would not work on the new 57500 chips.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested
or freed by the RDMA driver is wrong. After introducing reservation of
resources recently, the driver has to keep track of all stat_ctxs
including the ones used by the RDMA driver. This will provide a better
foundation for accurate accounting of the stat_ctxs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly. The
VFs will be assigned these available CP rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF has a pool of NQs and MSIX vectors assigned to it based on
NVRAM configurations. The number of usable MSIX vectors on the PF
is the minimum of the NQs and MSIX vectors. Any excess NQs without
associated MSIX may be used for the VFs, so we need to store this
max_nqs value. max_nqs minus the NQs used by the PF will be the
available NQs for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure to create debugfs entry is unpleasant event, but not enough
to abort drier initialization. Align the mlx5_core code to debugfs design
and continue execution whenever debugfs_create_dir() successes or not.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kzalloc_node(..., GFP_KERNEL, node) will attempt to allocate
memory as close as possible to the node.
There is no need to fallback to kzalloc() if this has failed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the ethtool entries to control the port should be supported by
the uplink rep netdev in switchdev mode, add them.
While here, add also the get/set coalesce entries for all reps.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards supporting set/get of global pause for the port
and get of the port link ksetting from the uplink representor,
expose the relevant entries to other mlx5 callers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some of the sriov ndo calls are needed also on the switchdev mode -
e.g setup VF mac and reading vport stats. Add them to the uplink rep
netdev ops. Same for the UDP tunnel ones, need them there to identify
offloaded udp tunnel ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take care of setup/teardown for the port link, dcb, lag as well as
dealing with port mtu and carrier for e-switch uplink representors.
This is achieved by adding a dedicated profile instance for uplink
representors which includes the enable/disable and more profile routines
which are invoked by the general mlx5e code for netdev attach/detach.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now, when we have a dedicated uplink representor, the netdev instance
set over the esw manager vport (PF) is of no-use. As such, remove it
once we're on switchdev mode and get it back to life when off switchdev.
This is done by reloading the Ethernet interface as well (we already
do that for the IB interface) from the eswitch code while going in/out
of switchdev mode.
The Eth add/remove entries are modified to act differently when called in
switchdev mode. In this case we only deal with registration of the eth
vport representors. The rep netdevices are created from the eswitch call
to load the registered eth representors.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove some last leftovers from using the PF netdev as
the e-switch uplink representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when running in sriov switchdev mode, we are using the PF
netdevice as the uplink representor, this is problematic from few aspects:
- will break when the PF isn't eswitch manager (e.g smart NIC env)
- misalignment with other NIC switchdev drivers
- makes us have and maintain special code, hurts the driver quality/robustness
- which in turn opens the door for future bugs
As of each and all of the above, we move to have a dedicated netdev representor
for the uplink vport in a similar manner done for for the VF vports.
This includes the following:
1. have an uplink rep netdev as we have for VF reps
2. all reps use same load/unload functions
3. HW stats for uplink based on physical port counters and not vport counters
4. link state for the uplink managed through PAOS and not vport state
5. the uplink rep has sysfs link to the PF PCI function && uses the PF MAC address
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is prep step towards adding dedicated uplink representor.
The patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The reload of the IB interface done on the offloads stop call is
redundant b/c we do that on mlx5_eswitch_disable_sriov(), remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Old firmware versions don't support this command. Sending it
to any firmware before -41.ucode will crash the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975
Fixes: 66e839030f ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE")
CC: <stable@vger.kernel.org> #4.19+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that mlxsw driver handles all aspects of updating
the Bloom filter mechanism, set bf_bypass value to false
and allow HW to use Bloom filter.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is updated on transitions from a single rule pattern,
also called master RP, to eRP table and vice versa. Since rules are
being written to or deleted from the Bloom filter on such transitions,
it is not required to keep the same eRP bank ID for the master RP.
Change master RP index assignment so it will be assigned with zero.
This is consistent with the assignment of the first available spot
that is used for allocating eRP's indices.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter update is required only for rules which reside on an
eRP. When the region has only a single rule pattern then eRP table
is not used, however insertion of another pattern would trigger a
move to an active eRP table so it is imperative to update the Bloom
filter with all previously configured rules.
Add a method that updates Bloom filter entries for all rules
currently configured in the region, on the event of a transition
from master mask to eRP, or vice versa. For that purpose, maintain
a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add calls to eRP module for updating Bloom filter when a rule is
added or removed from the A-TCAM. eRP module will update the Bloom
filter only for cases in which the region has an active eRP table.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Bloom filter update for rule insertion and rule removal scenarios.
This is done within eRP module in order to assure that Bloom filter
updates are done only for rules which are part of an eRP, as HW does not
consult Bloom filter for entries when there is a single (master) mask in
the region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 HW uses Bloom filter in order to skip lookups on specific
eRPs. It uses crc-16-Msbit-first calculation over a specific layout
of a rule's key fields combined with eRP ID as well as region ID.
Per potential lookup, iff the Bloom filter entry of the calculated
index is empty, then the lookup can be skipped. Hence, the mlxsw
driver should update the Bloom filter entry per each rule insertion
or deletion when rules are part of an eRP.
Add functions for adding and deleting entries in the Bloom filter.
In order to do so also add crc-16 computation based on the specific
Spectrum-2 polynomial and a function for encoding the crc-16 input
in the manner dictated by HW implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lay the foundations for Bloom filter handling. Introduce a new file for
Bloom filter actions.
Add struct mlxsw_sp_acl_bf to struct mlxsw_sp_acl_erp_core and initialize
the Bloom filter data structure. Also take care of proper destruction when
terminating.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the maximum Bloom filter logarithmic size per eRP table bank.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for a vxlan device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation. Add an opt-out flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.
The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.
This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.
The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.
So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000 size 0x800000
[37255.822192] flush cache 0xffff80003f000000 size 0x800000
[37255.828289] flush cache 0xffff80003f000000 size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Aviv Heller,
Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.
This series consists of the following:
- mlx5 devcom, driver infrastructure that facilitates operations that involve
both core devices (physical functions) of the same card, to synchronize and
communicate between two driver instances of the same card.
- Infrastructure for TC rule duplication.
- Changes to LAG logic to enable its use when SR-IOV is enabled
- PFs in switchdev mode is the only mode currently supported.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcFCCzAAoJEEg/ir3gV/o+VzIH/3xOcSuDIB7rM/mNoMtXVvvu
ZBZGUlUh7PoX/+fLjKYuQhosCvx1kpecPeNTa/R4yFy3kUl70CsKT6Cqtw2qGiPU
2hfr75MobM5nMwOU1QDXYyfSaXZsfUj25DE25OSvtMygR6YjeU0Lm4peWBnd9MD0
Oj5lilggS6hiNyCTI0s1D4tR0Uh2roj2tAGW7JRkd1Et34u9KZbBitCWvYkTtqcp
XauuCdjlDNZenOg0Lue9fAc4Jo9AVEaB2w/4dZDsarZyvabQ4DxVrmrVOgLmWBjc
Tr10JCuBvgdX/66JikJQ08Fkx/pHGby6jxcI4ux3QEoHe4/umm3Te0+5/pIxe58=
=wDuV
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-14 (VF Lag)
From Aviv Heller,
Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.
This series consists of the following:
- mlx5 devcom, driver infrastructure that facilitates operations that involve
both core devices (physical functions) of the same card, to synchronize and
communicate between two driver instances of the same card.
- Infrastructure for TC rule duplication.
- Changes to LAG logic to enable its use when SR-IOV is enabled
- PFs in switchdev mode is the only mode currently supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver issues 2 mmio reads to figure out the number of
transmitted packets and clean them. We can get rid of the expensive
reads since BIT 31 of the Tx descriptor can be used for that.
We can also remove the budget counting of Tx completions since all of
the descriptors are not deliberately processed.
Performance numbers using pktgen are:
size pre-patch(pps) post-patch(pps)
64 362483 427916
128 358315 411686
256 352725 389683
512 215675 216464
1024 113812 114442
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running pktgen with packets sizes > 512b ends up in the interface Txq
getting stuck.
"netsec 522d0000.ethernet eth0: netsec_netdev_start_xmit: TxQFull!"
appears on dmesg but the interface never recovers. It requires an
ifconfig down/up to make the interface usable again.
The reason that triggers this, is a race condition between
.ndo_start_xmit and the napi completion. The available budget is
calculated first and indicates the queue is full. Due to a costly
netif_err() the queue is not stopped in time while the napi completion
runs, clears the irq and frees up descriptors, thus the queue never wakes
up again.
Fix this by moving the print after stopping the queue, make the print
ratelimited, add barriers and check for cleaned descriptors..
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have the DEFINE_SHOW_ATTRIBUTE. There is no need to define
such a macro, so remove DEFINE_SIMPLE_DEBUGFS_FILE. Also use the
DEFINE_SHOW_ATTRIBUTE macro to simplify some code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All previous docks and dongles that have supported this feature use
the RTL8153-AD chip.
RTL8153-BND is a new chip that will be used in upcoming Dell type-C docks.
It should be added to the whitelist of devices to activate MAC address
pass through.
Per confirming with Realtek all devices containing RTL8153-BND should
activate MAC pass through and there won't use pass through bit on efuse
like in RTL8153-AD.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
corrected macro used in tx path. removed redundant hdrlen
and check for !page in chtls_sendmsg
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was checking for non-NULL address.
- adapter->napi[i]
This is pointless as these will be always non-NULL, since the
'dapter->napi' is allocated in init_napi().
It is safe to get rid of useless checks for addresses to fix the
coccinelle warning:
>>drivers/net/ethernet/ibm/ibmvnic.c: test of a variable/field address
Since such statements always return true, they are redundant.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Thomas Falcon <tlfalcon@linux.ibm.com>
CC: John Allen <jallen@linux.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linuxppc-dev@lists.ozlabs.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
tun_xdp_one() runs with local bh disabled. So there is no need to
disable preemption by calling get_cpu_ptr while updating stats. This
patch replaces the use of get_cpu_ptr() with this_cpu_ptr() as a
micro-optimization. Also removes related put_cpu_ptr call.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When create_lag or destroy_lag FW commands fail, display an appropriate
error message, and try to recover, if possible.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With the introduction of SR-IOV LAG, checking whether LAG is active
is no longer good enough, since RoCE and SR-IOV LAG each entails
different behavior by both the core and infiniband drivers.
This patch introduces facilities to discern LAG type, in addition to
mlx5_lag_is_active(). These are implemented in such a way as to allow
more complex mode combinations in the future.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The new name better represents the function's aim, and sets a precedent
for a '__' prefix for internal, non-locked versions of LAG APIs.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enable setting uplink LAG if sriov is enabled on both ports in switchdev
mode.
Once the sriov mode is changed from switchdev for any of the ports, the
LAG instance is disabled.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the lag forbid/allow functions, change the lag prereq check to
run in the do-bond logic, so every change in the prereq state will
cause LAG to be disabled/enabled accordingly after the next do-bond run.
Add lag update function, so every component which changes the prereq
state and want the LAG to re-calc the conditions can call the update
function.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When HW lag is set/unset, roce must not be enabled on the port, as such
we wrap such changes with roce enable/disable either directly or through
re-creation of IB device.
Currently, lag and sriov are mutually exclusive, so by definition this
code doesn't run under sriov.
Towards changing this exclusion, we need to make sure that roce will not
be enabled on the eswitch manager port under sriov since this is
requirement of the switchdev mode.
We are going strict here and avoiding this all together under sriov.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under uplink LAG, packets that match a flow might arrive on both uplink
ports and transmitted through both as part of supporting aggregation and
high-availability.
When the netdevs representing the uplinks are set into LAG (bonding,
teaming), duplicate the TC flow offloading into each of the per-uplink
e-switches.
Duplication is not required if the source is the bond device, since in
this case it is assumed that the bond and the uplink netdevs share the
same TC block, and thus duplication will occur naturally by the stack.
Note that under encapsulation scheme, both flows will use the same
neighbour and hence both will contribute to the last-used feedback
towards the stack.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When parsing TC FDB actions, if the egress device is a bond/team
net-device which enslaved the uplink representor of the e-switch,
use the uplink representor as the destination in the HW rule.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the uplink representors are put into lag, set all the
representors (VFs and uplinks) of the same NIC to return the same
switchdev id.
Currently, the route lookup code on the encapsulation offload path
assumes that same switchdev id for the source and dest devices means
that the dest is also mlx5 HW netdev. This doesn't hold anymore when we
align the switchdev Id of the uplinks to be same, which in turn causes
the bond/team to return that id to the caller. As such, enhance the
relevant check to take into account the uplink lag case.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Assign a counter dev attribute according to device capability and use
it for management of counters related to offloaded eswitch TC flows.
With upcoming support for uplink LAG, we have two HW rules per one
logical SW (TC) rule. Although the HW supports attaching one counter
to multiple rules, we are allocating counter per HW rule.
We need this separation for two reasons:
1. "flow eswitch" counter affinity HW require the counter to be
allocated on the device where the eswitch rule is set.
2. for some use-cases (multi-path routing) each HW flow relates to
different neighbour, hence our neigh update logic must have a per-rule
HW accountant in order to provide the proper feedback to the kernel.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under uplink LAG or multipath schemes, traffic that matches one flow
might arrive on both uplink ports and transmitted through both
as part of supporting aggregation and high-availability.
To cope with the fact that the SW model might use logical SW port
(e.g uplink team or bond) but we have two HW ports with e-switch on
each, there are cases where in order to offload a SW TC rule we
need to duplicate it to two HW flows.
Since each HW rule has its own counter we also aggregate the counter
of both rules when a flow stats query is executed from user-space.
Introduce the changes for the different elements (add/delete/stats),
currently nothing is duplicated.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the sriov offloads mode, packets that are not matched by any
other rule are sent towards the e-switch vport manager for further
processing.
Under upcoming patches (e.g for uplink LAG), packets sent from VF
vports belonging to esw0 (e-switch related to PF0) might end up in
esw1 (e-switch related to PF1) due to muxing logic applied by the
FW.
In such a case we still want the missed packet to be sent to the
"base" esw manager vport in order to present the control plane a
consistent view of the source (VF reresentor) port.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This introduces devcom, a generic mechanism for performing operations
on both physical functions of the same Connect-X card.
The first user of this API is merged eswitch, which will be introduced
in subsequent patches.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ppp and hamradio have copies of the same code that uses a semaphore
in place of a completion for historic reasons. Make it use the
proper interface instead in all copies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now get a link failure when CONFIG_INET is disabled, since
tcp_gro_complete is unavailable:
drivers/net/ethernet/hisilicon/hns3/hns3_enet.o: In function `hns3_set_gro_param':
hns3_enet.c:(.text+0x230c): undefined reference to `tcp_gro_complete'
Add an explicit CONFIG_INET dependency here to avoid the broken
configuration.
Fixes: a6d53b97a2 ("net: hns3: Adds GRO params to SKB for the stack")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) Lag refactroing and flow counter affinity bits.
2) mlx5 core cleanups
By Roi Dayan (2) and others
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Handle the code of modifying the lag affinity within a separate function.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Report the initial LAG port affinity upon LAG creation.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Split the activate lag function in order to be symmetric with
the deactivate lag function.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We used to have many versions of statistics notification
coming from the firmware. In one of the cleanup patches,
we forgot to clean the code that checks if data->general
is set. Since it is always set, remove the check.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
command len is set too early in the code, since when building
AMSDU, the size changes. This causes the byte count table to
have the wrong size.
Fixes: a0ec0169b7 ("iwlwifi: support new tx api")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
UL_DL is irrelevant to HE TRIG_BASED PPDU.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We may have the L-SIG length depending on the phy_data info type;
add it to radiotap when we do.
Move getting the phy_data out one layer up and the info type into
it so we can use this data more generically. We need to call the
iwl_mvm_rx_he() function for other reasons as well, so can't just
combine all of that into something like iwl_mvm_parse_phy_data().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware changed the PHY data API, so follow suit.
Some data is now available even for HT/VHT frames, so
the info type in the metadata was changed. This change
isn't backwards compatible, but
1) the firmware with the old API was never released;
2) the only overlap in the info type field is from the
old type of TB to the new of HT, so this basically
just means that with older FW and newer driver the
data will be considered missing.
While at it, remove the extra code to set the LTF syms
corresponding to the streams and use the data from the
device instead - we don't really need this in any case
other than when we have it from the device.
As the new API gives use the spatial reuse 1-4 fields
for trigger-based PPDUs, also expose that to radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing the driver, the following flow can happen:
1. host command is in progress, for example at index 68.
2. RX interrupt is received with the response.
3. Before it is processed, the remove flow kicks in, and
calls iwl_pcie_txq_unmap. The function cleans all DMA,
and promotes the read pointer to 69.
4. RX thread proceeds with the processing, and is calling
iwl_pcie_cmdq_reclaim, which will print this error:
iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0),
index 4 is out of range [0-256] 69 69.
Detect this situation, and avoid the print. Change it to
warning while at it, to make such issues more noticeable
in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.
Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that nvm_calib_ver is not checked in opmodes other than dvm, we
can remove it from all irrelevant configurations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is only half-used by mvm (i.e. only the nvm_version part
matters, since the calibration version is irrelevant), so it's
pointless to export it from iwlwifi. If mvm uses this function, it
has the additional complexity of setting the calib version to a bogus
value on all cfg structs.
To avoid this, move the function to dvm and make a simple comparison
of the nvm_version in mvm instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These macros are useless because each one of them is used only once
and the element they are assigned to is already pretty clear about
what they mean, "nvm_hw_section_num".
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Using OTP_LOW_IMAGE_SIZE_FAMILY_8000/9000/22000 only obfuscates the
actual values, since these 3 are the same. Redefine the values per
size so it's easier to understand and compare the different
configurations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Call the previously introduced apply points entry
point when reaching an apply point.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ht_params, nvm_ver, nvm_calib_ver and max_ht_ampdu_exponent
elements in 9000 devices are always the same. Move them to the common
macro.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.
Fixes: cac6f69154 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcEiXXAAoJEEg/ir3gV/o+xxQH/jGS6GQrty9puL40sXKE4ryK
GKVSwbKLnu4WatPcLe/CGxJwRoCVUUKfsbprsuy+oYxhUd5M5h6qu215kZgsfdDC
CfxznbEj3o6mN+ZyZjL+F2gEG6e96bpkKvayb2a9YYQaY/9+V6CMKh3U5jHI+Q2V
D4ToCjWbMXkQ0jsevfpV9W2T0DNfXIa5QGvsvH+D+PoLF/ke/YALZd+yJT0Cm9N2
/vp0qvnHnZO5YavEThN2Lh8f9AY/pAwuGgTrPyddfkZC/6QLH+c8948gF14V+03l
Nz78uSpurQ97X511UBcabSQB0xTCHSAw3/SKCVSxFrpMvkhj4mTbjohwc567Gy4=
=YxUz
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-fixes-2018-12-13
Subject: [pull request][net 0/9] Mellanox, mlx5 fixes 2018-12-13
Saeed Mahameed says:
====================
This series introduces some fixes to the mlx5 core and mlx5e netdevice
driver.
=======
Conflict with net-next: When merged with net-next this series will
cause a moderate conflict:
1) in drivers/net/ethernet/mellanox/mlx5/core/en_tc.c (2 hunks)
Take hunks from net only and just replace *attr->mirror_count to *attr->split_count
1.1) there is one more instance of slow_attr->mirror_count to be replaced
with slow_attr->split_count, it doesn't appear in the conflict, it will
cause a compilation error if left out.
2) in mlx5_ifc.h, take hunks only from net.
Example for the merge resolution can be found at:
https://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git/commit/?h=merge/mlx5-fixes&id=48830adf29804d85d77ed8a251d625db0eb5b8a8
branch merge/mlx5-fixes of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
(I simply merged this pull request tag into net-next and resolved the conflict)
I don't know if it's ok with you, but to save your time, you can just:
git pull git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux merge/mlx5-fixes
Into net-next, before your next net merge, and you will have a clean
merge of net into net-next (at least for mlx5 files).
======
Please pull and let me know if there's any problem.
For -stable v4.18
338d615be484 ('net/mlx5e: Cancel DIM work on close SQ')
91f40f9904ad ('net/mlx5e: RX, Verify MPWQE stride size is in range')
For -stable v4.19
c5c7e1c41bbe ('net/mlx5e: Remove unused UDP GSO remaining counter')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On NETDEV_PRE_CHANGEADDR, if the change is related to a RIF interface,
verify that it satisfies the criterion that all RIF interfaces have the
same MAC address prefix, as indicated by mlxsw_sp.mac_mask.
Additionally, besides explicit address changes, check that the address
of an interface for which a RIF is about to be added matches the
required pattern as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum hardware demands that all router interfaces in the system
have the same first 38 resp. 36 bits of MAC address: the former limit
holds on Spectrum, the latter on Spectrum-2. Add a field that refers to
the required prefix mask and initialize in mlxsw_sp1_init() and
mlxsw_sp2_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare mlxsw_sp_netdevice_router_port_event() for handling of
NETDEV_PRE_CHANGEADDR. Split out the part that deals with the actual
changes and call it for the two events currently handled.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give interested parties an opportunity to veto an impending HW address
change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before NETDEV_CHANGEADDR, bond driver should emit NETDEV_PRE_CHANGEADDR,
and allow consumers to veto the address change. To propagate further the
return code from NETDEV_PRE_CHANGEADDR, give the function that
implements address change a return value.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NETDEV_CHANGEADDR event implies a change of address of each of the
IPVLANs of this IPVLAN device. Therefore propagate NETDEV_PRE_CHANGEADDR
to all the IPVLANs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c: In function 'translate_rx_signal_stuff':
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c:309:6: warning:
variable 'type' set but not used [-Wunused-but-set-variable]
It never used since commit 21e4b0726d ("rtlwifi: rtl8821ae: Move driver from
staging to regular tree")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: Pan Bian <bianpan2016@163.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/phy_n.c: In function 'b43_nphy_op_recalc_txpower':
drivers/net/wireless/broadcom/b43/phy_n.c:5898:7: warning:
variable 'tx_pwr_state' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/b43/phy_n.c:6047:20: warning:
variable 'tmp2' set but not used [-Wunused-but-set-variable]
'tx_pwr_state' never used since introduction in commit
8615eb2870 ("b43: N-PHY: support setting custom TX power")
'tmp2' not used any more since commit c002831a07 ("b43: N-PHY: use helper
for checking IPA")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_NO_AUTO_INLINE is set, we get a false-postive warning
for the brcmf_fw_request_nvram_done() function, after gcc figures
out that brcmf_fw_nvram_from_efi() might not set the 'data_len'
variable, but fails to notice that it always returns NULL:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c: In function 'brcmf_fw_request_nvram_done':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:560:11: error: 'data_len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Mark it 'inline' to force gcc to understand this.
Fixes: ce2e6db554 ("brcmfmac: Add support for getting nvram contents from EFI variables")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.
Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.
Command decode for below chips are disabled in this commit:
- 4339
- 4345
- 4354
- 4373
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use chipcommon sr_control0 register to check 4373 sr support.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
- Allow GCI to be added to core list even when it doesn't have a wrapper.
- Allow 8K address space size.
- Don't overwrite the address value when an additional size descriptor
is in place.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware inform the driver about tx status by normal tx status signal
or compressed tx status signal. This patch adds support to handle the
compressed tx status signal.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The credit numbers are static and tunable per chip in firmware side.
However the credit number may be changed that is based on packet pool
length and will send BRCMF_E_FIFO_CREDIT_MAP event to notify host driver
updates the credit numbers during interface up.
The purpose of this patch is making host driver has ability of updating
the credit numbers when receiving the BRCMF_E_FIFO_CREDIT_MAP event.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Comparing the existing TX_BITRATE parsing code (in
mwifiex_parse_htinfo()) with the RX bitrate histograms in debugfs.c, it
appears that the rxpd_rate and rxpd_htinfo fields have the same format.
At least, they give reasonable results when I parse them this way.
So this patch adds support for RX_BITRATE to our station info dump.
Along the way, I add legacy bitrate parsing into the same function,
using the debugfs code (mwifiex_histogram_read() and
mwifiex_adjust_data_rate()) as reference.
Additionally, to satisfy the requirements of
NL80211_STA_INFO_RX_BITRATE, I skip logging the bitrate of multicast
packets. This shouldn't add a lot of overhead to the RX path, as there
are already several similar 802.3 header checks in this same codepath.
We can also bias the branch behavior to favor unicast, as that's the
common performance-sensitive case.
I'd consider this support somewhat experimental, as I have zero
documentation from Marvell. But the existing driver code gives me good
reason to think this is correct.
I've tested this on a few different 802.11{a,b,g,n,ac} networks, and the
reported bitrates look good to me.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function converts some firmware-specific parameters into cfg80211
'rate_info' structures. It currently assumes it's dealing only with TX
bitrate, but the RX bitrate looks to be the same, so refactor this
function to be reusable.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, snippets of this file look like:
rx rates (in Mbps): 0=1M 1=2M2=5.5M 3=11M 4=6M 5=9M 6=12M
7=18M 8=24M 9=36M 10=48M 11=54M12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)
44-53=MCS0-9(VHT:BW20)54-63=MCS0-9(VHT:BW40)64-73=MCS0-9(VHT:BW80)
...
noise_flr[--96dBm] = 22
noise_flr[--95dBm] = 149
noise_flr[--94dBm] = 9
noise_flr[--93dBm] = 2
We're missing some spaces, and we're adding a minus sign ('-') on values
that are already negative signed integers.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two defects: (1) passing a NULL bss to
mwifiex_save_hidden_ssid_channels will result in NULL dereference,
(2) using bss after dropping the reference to it via cfg80211_put_bss.
To fix them, the patch moves the buggy code to the branch that bss is
not NULL and puts it before cfg80211_put_bss.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Starting from mac80211 commit adf8ed01e4 ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlwBH4oACgkQ130UHQKnbvUdQwCdFL9rDWnaX1nvSwLZrp3DC7qD
CywAoJaygMHs0YVmXWHQ9tdEAY5i4VAO
=qF8w
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-11-30' of https://github.com/nbd168/wireless
first batch of mt76 patches for 4.21
* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
kvalo: fixed a conflict in drivers/net/wireless/mediatek/mt76/mt76x2/pci_main.c
and a build problem in drivers/net/wireless/mediatek/mt76/mt76x02_util.c
This reverts commit 5188d5453b, because it
introduced lock recursion:
BUG: spinlock recursion on CPU#2, kworker/u13:1/395
lock: 0xffffffc0e28a47f0, .magic: dead4ead, .owner: kworker/u13:1/395, .owner_cpu: 2
CPU: 2 PID: 395 Comm: kworker/u13:1 Not tainted 4.20.0-rc4+ #2
Hardware name: Google Kevin (DT)
Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
Call trace:
dump_backtrace+0x0/0x140
show_stack+0x20/0x28
dump_stack+0x84/0xa4
spin_bug+0x98/0xa4
do_raw_spin_lock+0x5c/0xdc
_raw_spin_lock_irqsave+0x38/0x48
mwifiex_flush_data+0x2c/0xa4 [mwifiex]
call_timer_fn+0xcc/0x1c4
run_timer_softirq+0x264/0x4f0
__do_softirq+0x1a8/0x35c
do_softirq+0x54/0x64
netif_rx_ni+0xe8/0x120
mwifiex_recv_packet+0xfc/0x10c [mwifiex]
mwifiex_process_rx_packet+0x1d4/0x238 [mwifiex]
mwifiex_11n_dispatch_pkt+0x190/0x1ac [mwifiex]
mwifiex_11n_rx_reorder_pkt+0x28c/0x354 [mwifiex]
mwifiex_process_sta_rx_packet+0x204/0x26c [mwifiex]
mwifiex_handle_rx_packet+0x15c/0x16c [mwifiex]
mwifiex_rx_work_queue+0x104/0x134 [mwifiex]
worker_thread+0x4cc/0x72c
kthread+0x134/0x13c
ret_from_fork+0x10/0x18
This was clearly not tested well at all. I simply performed 'wget' in a
loop and it fell over within a few seconds.
Fixes: 5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage")
Cc: <stable@vger.kernel.org>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing
C2H_BT_INFO"), calling rtl_c2hcmd_enqueue() with rtl_c2h_fast_cmd() true,
the routine returns without freeing that skb, thereby leaking it.
This issue has been discussed at https://github.com/lwfinger/rtlwifi_new/issues/401
and the fix tested there.
Fixes: 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing C2H_BT_INFO")
Reported-and-tested-by: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TXQ SQ closure is followed by closing the corresponding CQ. A pending
DIM work would try to modify the now non-existing CQ.
This would trigger an error:
[85535.835926] mlx5_core 0000:af:00.0: mlx5_cmd_check:769:(pid 124399):
MODIFY_CQ(0x403) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1d7771)
Fix by making sure to cancel any pending DIM work before destroying the SQ.
Fixes: cbce4f4447 ("net/mlx5e: Enable adaptive-TX moderation")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove tx_udp_seg_rem counter from ethtool output, as it is no longer
being updated in the driver's data flow.
Fixes: 3f44899ef2 ("net/mlx5e: Use PARTIAL_GSO for UDP segmentation")
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we are deleting offloaded encap flows in case the relevant neigh
becomes unconnected while the encap is valid (a sign that it used to be
connected), or if the curr neigh mac is different from the cached mac
(a sign that the remote side changed their mac).
The 2nd check also applies when the neigh becomes connected on the 1st
time (we start with zero mac). Before the offending commit, the deleting
handler was practically no op, as no flows were offloaded. But since
that commit, we offload neigh-less encap flows to slow path.
Under mirroring scheme, we go into the delete handler, attempt to unoffload a
mirror rule which was never set (as we were offloading to slow path) and crash.
Fix that by calling the delete handler only when the encap is valid,
which covers both cases mentioned above.
Fixes: 5dbe906ff1 ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a neighbour is resolved, we delete the goto slow path rule from HW.
The eswitch flow attributes where not properly initialized on that case,
hence we mess up the eswitch refcounts for chain zero (the default one).
Fix that along with making sure to use semicolons and not commas on that code;
Fixes: 5dbe906ff1 ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Just a leftover which was wrongly left there, remove it while spawning
a message to suggest firmware upgrade.
Fixes: bf07aa730a ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we are not supporting this and not err-ing on that either.
For now, just err if asked to do that.
Fixes: bf07aa730a ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add check of MPWQE stride size is within range supported by HW. In case
calculated MPWQE stride size exceed range, linear SKB can't be used and
we should use non linear MPWQE instead.
Fixes: 619a8f2a42 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The default amount of channels a representor opens was erroneously
changed from one to the maximum amount of channels, restore to its
intended value.
Fixes: 779d986d60 ("net/mlx5e: Do not ignore netdevice TX/RX queues number")
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Prevent a namespace conflict as in following patches as skbuff.h will
include the crypto API.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
From Eli Britstein,
Patches 1-10 adds remote mirroring support.
Patches 1-4 refactor encap related code as pre-steps for using per
destination encapsulation properties.
Patches 5-7 use extended destination feature for single/multi
destination scenarios that have a single encap destination.
Patches 8-10 enable multiple encap destinations for a TC flow.
From, Daniel Jurgens,
Patch 11, Use CQE padding for Ethernet CQs, PPC showed up to a 24%
improvement in small packet throughput
From Eyal Davidovich,
patches 12-14, FW monitor counter support
FW monitor counters feature came to solve the delayed reporting of
FW stats in the atomic get_stats64 ndo, since we can't access the
FW at that stage, this feature will enable immediate FW stats updates
in the driver via fw events on specific stats updates.
Patch 12, cleanup to avoid querying a FW counter when it is not
supported
Patch 13, Monitor counters FW commands support
Patch 14, Use monitor counters in ethernet netdevice to update FW
stats reported in the atomic get_stats64 ndo.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcEEYmAAoJEEg/ir3gV/o+XlIIAKIQhvHnCoGMPsZU+HbA1h3O
10i2hnmQqx2F5Z7tSON9jr9HVzLj6FqQ3pSnTyw8xiMBqOldF6abmfpMPQ/XeWXk
PDBCzfOUMAlIsGFAJ06tcz3VLkWrEdoQHmi7Jb4IW+LC9CnZBobzrcLaxQ95txYP
LkCfO8Y70D5tzBrzL1o1RfKsCSFJma5zhXDPF/B3rifLyHOmo9aLzZuDvKwvvSkC
Y3QM5ulnLqVhxaXA0xzB+iHLiI0nX2H17CBPseLzM+Ip0vZS/nA77rnQ49PUgjiZ
d1BoXo9MUa3eoQwXNl+qSAfnGjCwqzplXxzjT2bKKXVc2ZOWmkECgRXmKI6JDDU=
=EuqQ
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-11
From Eli Britstein,
Patches 1-10 adds remote mirroring support.
Patches 1-4 refactor encap related code as pre-steps for using per
destination encapsulation properties.
Patches 5-7 use extended destination feature for single/multi
destination scenarios that have a single encap destination.
Patches 8-10 enable multiple encap destinations for a TC flow.
From, Daniel Jurgens,
Patch 11, Use CQE padding for Ethernet CQs, PPC showed up to a 24%
improvement in small packet throughput
From Eyal Davidovich,
patches 12-14, FW monitor counter support
FW monitor counters feature came to solve the delayed reporting of
FW stats in the atomic get_stats64 ndo, since we can't access the
FW at that stage, this feature will enable immediate FW stats updates
in the driver via fw events on specific stats updates.
Patch 12, cleanup to avoid querying a FW counter when it is not
supported
Patch 13, Monitor counters FW commands support
Patch 14, Use monitor counters in ethernet netdevice to update FW
stats reported in the atomic get_stats64 ndo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-12-12
This series contains fixes to i40e and ixgbe.
Stefan Assmann fixes an issue created by a previous fix, where
ether_addr_copy() was moved to avoid a race but did not take into
account that it alters the MAC address being handed to
i40e_del_mac_filter().
Michał Mirosław provides 2 fixes for i40e, first resolves issues in the
hardware VLAN offload where VLAN.TCI equal to 0 was being dropped and a
race between disabling VLAN receive feature in hardware and processing
the receive queue, where packets could have their VLAN information
dropped.
Ross Lagerwall fixes a racy condition during a ixgbe VF reset, where
writing the register to issue a reset and sending the reset message via
the mailbox API could result of the mailbox memory getting cleared
during the reset before the message gets successfully sent which results
in a VF driver malfunction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_LICENSE info to fix this:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.o
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_load':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1490:21: warning:
variable 'upriv' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_unload':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1557:21: warning:
variable 'upriv' set but not used [-Wunused-but-set-variable]
It not used any more since commit ef381359e3 ("net/mlx5e: Replace egdev with
indirect block notifications"). Also remove unused variable 'uplink_rpriv'
after this change.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After switchdev_handle_port_obj_add() was extended in a preceding patch,
mlxsw_sp_port_obj_add() now takes an extack argument. Propagate it
further by extending a callee chain from mlxsw_sp_port_vlans_add(), via
mlxsw_sp_bridge_port_vlan_add() via mlxsw_sp_port_vlan_bridge_join() via
mlxsw_sp_port_vlan_fid_join() to mlxsw_sp_bridge_ops.fid_get, adding an
extack argument for each of them.
This code path is used when a VLAN is added to a port netdevice if there
already is an unoffloadable VXLAN device with that VLAN mapped.
mlxsw_sp_bridge_8021d_port_join() is updated to obey the new interfaces
changed by the abovementioned code, propagating extack ultimately from
NETDEV_CHANGEUPPER events.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that VLAN port object addition notifications carry an extack,
propagate it from mlxsw_sp_switchdev_vxlan_vlans_add() through
mlxsw_sp_switchdev_vxlan_vlan_add() to
mlxsw_sp_bridge_8021q_vxlan_join().
This code path is used when a VLAN is added to a VXLAN netdevice that
cannot be offloaded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers use switchdev_handle_port_obj_add() to handle recursive descent
through lower devices. Change this function prototype to take add_cb
that itself takes an extack argument. Decode extack from
switchdev_notifier_port_obj_info and pass it to add_cb.
Update mlxsw and ocelot drivers which use this helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack to the drivers that need it, add an extack field
to struct switchdev_notifier_info, and an extack argument to the
function call_switchdev_blocking_notifiers(). Also add a helper function
switchdev_notifier_info_to_extack().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en 0000:19:00.0 (unregistered net_device) (uninitialized): hwrm
req_type 0x190 seq id 0x6 error 0xffff
The message above is commonly seen when a newer driver is used on
hardware with older firmware. The issue is this message means nothing to
anyone except Broadcom. Remove the message to not confuse users as this
message is really not very informative.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be only one PHC clock per port. PTP should be enabled only on
one PF per port. The change enables PTP functionality on the PF that
initializes the port. The change is useful in multi-function modes e.g.,
NPAR where a port can have more than one PF.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad6 ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move rx_ptype extracting to i40e_process_skb_fields() to avoid
duplicating the code.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two bugs in hardware VLAN offload:
1. VLAN.TCI == 0 was being dropped
2. there was a race between disabling of VLAN RX feature in hardware
and processing RX queue, where packets processed in this window
could have their VLAN information dropped
Fix moves the VLAN handling into i40e_process_skb_fields() to save on
duplicated code. i40e_receive_skb() becomes trivial and so is removed.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add Ethernet support for MediaTek SoCs from the mt2712 family
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEEUXMr/TfP2p4suIY5Dlx4XIBNgtkFAlwQj94OHGtpc2hvbkB0
aS5jb20ACgkQDlx4XIBNgtmYrA/9HK7yfOWfNLJ7DB8bi4yPx5hd657sLohSdDEX
0Pxx9PRuxjLYlaHQh8XbHEdvnLIbbGgnHbfvkkHjxJx272G+QAWMi7/SwF3a2ZpY
ev7U1gvWvCTqS/3RsEmxmwiX9esszcOgya2ia5TcyvTIHLla0QXTOUCmOQBejWhJ
Wfe3siSzxn6O4BITsoRUu+0Ek3bScW/cFdby5B62zBrs912p1qlGx20ihvjywB6I
uR5q1w5DxCbC9KZLTkQgfPXki69r1EaCYzdcEKnUON59OXceIy/TKDx/ewZBOjtR
/d+lWybsLMF5MXIy2UKlaKxLrk4AVdsQ6zmfU23uTqCT3rWn7OPEvbzSj3nBXpgi
SNzBTt9wHT4ZAGOq4fmhgF1Gn1gx4tEcarvAfeyyzv1riVgGbwlxSaUpWWvkya/E
zDBqROi/9VU+WX+De+E2KTCAOjJpcnVpLx8euA7uSD2m0nF4Kp4YiyAJiH/ZDQba
ghhR4DiD1xhjO77U+tM7mD+68ZyKsQubqzO+h4rztjZ/QRCWqGtOCg9sSQBxSz86
llEklLB3156dkLnHRMd0NIuSqYGOkHLWdTBrXNr2HaK7ZWvN6jxhC2puziIlmIZl
8m94QyY5pmuTJdQsWA/MEoWFglQqLBDxAVuoMH4d/XFx7PBNxiaTGOOEgX7MhfVM
9di9hak=
=JLIJ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.21
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (30 commits)
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
phy: Add MIPI D-PHY configuration options
phy: Add configuration interface
phy: Add MIPI D-PHY mode
phy: add driver for Freescale i.MX8MQ USB3 PHY
dt-bindings: phy: add binding for Freescale i.MX8MQ USB3 PHY
phy: Use of_node_name_eq for node name comparisons
net: ethernet: ti: cpsw: add support for port interface mode selection phy
dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
phy: ti: introduce phy-gmii-sel driver
dt-bindings: phy: add cpsw port interface mode selection phy bindings
phy: mvebu-cp110-comphy: fix spelling in structure name
phy: mapphone-mdm6600: Improve phy related runtime PM calls
phy: renesas: rcar-gen3-usb2: follow the hardware manual procedure
phy: cadence: Add driver for Sierra PHY
...
Add implementation of Spectrum-2 multicast routes for both IPv4 and IPv6 by
using ACL module explicitly.
In Spectrum-2, multicast routes are set as ACL rules, so initialization
takes care of creating dedicated ACL groups and binding them to the
appropriate multicast routing protocol IPv4/IPv6, and afterwards routes
configuration translates to setting explicit ACL rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is
required for multicast routing.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, MC routing is implemented using ACL block explicitly, so
router initialization should take place after ACL initialization.
Set the initialization of the ACL block before IP router initizalization
takes place, so multicast router will be able to allocate ACL data
structures and create its required chains.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to schedule a different tasklet for refill,
This patch remove it.
Suggested-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for port interface mode selection phy (phy-gmii-sel):
- try to request interface mode selection phy from Port DT node and fail
silently if not defined and old CONFIG_TI_CPSW_PHY_SEL driver enabled.
- use new phy if requested successfully.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Convert mvebu-cp110-comphy PHY driver to use recently introduced
PHY_MODE_ETHERNET and phy_set_mode_ext().
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- Adding new notifier block (struct mlx5_nb) monitor_counters_nb
for handeling MONITOR_COUNTER new event type.
- Adding work queue element: monitor_counters_work for re-arm and
update stats.
- We re-queue the update stat work, only when working over firmware
that doesn't support the monitored counters.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
new file monitor_stats.c for the new API.
add arm_monitor_counter new command support.
add set_monitor_counter new command support.
The device can monitor specific counters and provide an event to notify
when these counters are changed.
The monitoring is done in best effort manner where the minimum
notification period is 200 ms, however when the device is loaded, the
notification might be delayed.
To configure the required counters to be monitored, the
SET_MONITOR_COUNTER command shall be used with a list of counters to be
monitored.
The device firmware can monitor up to HCA_CAP.max_num_of_monitor_counters.
The configuration is done based on counter type (such as ppcnt, q counter,
etc) and additional param according to the type of counter selected.
Upon monitor counter change, the device will generate
Monitor_Counter_Change event.
The device will not generate new events unless the driver re-arms the
monitoring functionality, using the ARM_MONITOR_COUNTER command.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding
the CQEs to 128B if possible improves performance on 128B cache line
systems like PPC.
Testing on PPC showed up to a 24% improvement in small packet throughput
vs the default behavior, depending on the workload and system topology.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow is associated with a single encap structure. The FW
extended destination features enables the driver to associate a flow
with multiple encap instances.
Change the encap id field from a flow scope to a per destination value
in the flow attributes struct. Use the encaps array to associate a flow
table entry with multiple encap entries.
Update the neigh logic to offload only if all encapsulations used in a
flow are connected, and un-offload upon the first one disconnected.
Note that the driver can now support up to two encap destinations.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow can be associated with a single encap entry. The
extended destination feature enables the driver to configure multiple
encap entries per flow.
Change the encap flow association field to array as a pre-step towards
supporting multiple encap destinations. Use only the first array
element, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver can support only a single TC tunnel_set action.
Change the tunnel info fields to arrays, as a pre-step to support
multiple encapsulations for a single flow, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A rule with the following actions is split to a two level FDB:
1. Forward to local mirror vport
2. Header rewrite
3. Forward to local vport
In the first level flow table, forward the packet to the local port and
forward the packet to the second level flow table for header rewrite and
local port forwarding. This configuration fails when mirroring to a
remote encapsulated destination because currently an FTE cannot support
encap and table destinations.
Use the extended destination capabilities to configure the first level
flow table with a multi-destination FTE to the uplink and second level
table and the second level flow table for the header rewrite and local
port forwarding.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the FTE encap flag applies to all destinations.
To support mirroring encapsulated traffic to a local port the driver
split the two destinations to two flow table entries:
Table#0: - FWD to the local vport
- Goto table#1
Table#1: - Encap and FWD to wire
The firmware extended destination capabilities enable the driver to set
an encapsulation flag per destination.
Remove the split logic and use the extended destination mechanism
instead.
Note that split technique is still required for pedit and VLAN push
scenarios.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a FW syndrome is emitted if the driver configures a
multi-destination FTE where the first destination is a tunneled uplink
port and the second destination is a local vPort.
Support this scenario by creating a multi-destination FTE using the
firmware's extended destination capabilities.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow attr reformat action bit is moved from the global action bits to a
per destination flags field, as a pre-step for adding additional flags
to support encapsulation properties per destination, with no
functionality change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the eswitch flow attr structure stores each destination
specific property in its own specific array.
Group them in an array of destination structures as a pre-step towards
adding additional destination specific field properties.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The mirror count esw attributes field is used to determine if splitting
the rule to two FTEs is required while programming e-switch mirroring.
Rename it to split count, making it clearer with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver identifies identical vport destinations by
comparing the vport ID. The FW extended destination feature enables the
driver to forward the packet to the same vport with multiple
encapsulation properties.
Change the vport destination comparison logic to compare
the encapsulation properties in addition to the vport ID.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-12-11
An update from ieee802154 for your *net* tree.
Just two more fixes for ieee802154 dribver before the final 4.20 release.
Alexander Aring fixes a problem in the nested parsing code of the
hwsim driver interface.
A fix for a potential overflow in the ca8210 driver by Yue Habing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warning this:
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfc ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add HW offloading support for TC flower filters configured on
gretap/ip6gretap net devices.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
This approach aligns with the current identification methods and function
names of vxlan and geneve network devices.
Convert mlxsw to use these helpers and use them in downstream mlx5 patch.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move tunnel offloading related code to a separate source file for better
code maintainability.
Code refactoring with no functional change.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the tunnel offloading encap/decap methods assumes that VXLAN
is the sole tunneling protocol. Lay the infrastructure for supporting
multiple tunneling protocols by branching according to the tunnel
net device kind.
Encap filters tunnel type is determined according to the egress/mirred
net device. Decap filters classify the tunnel type according to the
filter's ingress net device kind.
Distinguish between the tunnel type as defined by the SW model and
the FW reformat type that specifies the HW operation being made.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Separates the vxlan header match handling from the matching on the
general fields of ipv4/6 tunnels, thus allowing the common IP tunnel
match code to branch in down stream patch, to multiple IP tunnels.
This patch doesn't add any functionality.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Separates the vxlan header encap logic from the general ipv4/6
encapsulation methods, thus allowing the common IP encap/decap code to
branch in downstream patch to multiple IP tunnels.
Code refactoring with no functional change.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use TC indirect block notifications to offload filters that
are configured on higher level device interfaces (e.g. tunnel
devices). This mechanism replaces the current egdev implementation.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Propagate the filter's net_device parameter to the tc flower parsed
attributes structure so that it can later be used in tunnel decap
offloading sequences.
Pre-step for replacing egdev logic with the indirect block
notification mechanism.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver controls flower filters that are installed on its
devices. However, with the introduction of the indirect block
notifications platform the driver may receive control events for filters
that are installed on higher level net devices (e.g. tunnel devices).
Therefore, the driver filter control API will not be able to implicitly
assume the filter's net device.
Explicitly specify the filter's net device, no functional change
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards using this mechanism as the means to offload tunnel decap rules
set on SW tunnel devices instead of egdev, add the supporting structures
and functions.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently only a single field in the representor private structure
is relevant for uplink representors. As a pre-step to allow adding
additional uplink representor fields, introduce uplink representor
private structure.
This is prepration step towards replacing egdev logic with the
indirect block notification mechanism. This patch doesn't change
any functionality.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) RDMA ODP (On Demand Paging) improvements and moving ODP logic to
mlx5 RDMA driver
2) Improved mlx5 core driver and device events handling and provided API
for upper layers to subscribe to device events.
3) RDMA only code cleanup from mlx5 core
4) Add helper to get CQE opcode
5) Rework handling of port module events
6) shared mlx5_ifc.h updates to avoid conflicts
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This isn't used anywhere across the mlx5 driver stack,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update the flow steering command formatting according to the extended
destination API.
Note that the FW dictates that multi destination FTEs that involve at
least one encap must use the extended destination format, while single
destination ones must use the legacy format.
Using extended destination format requires FW support. Check for its
capabilities and return error if not supported.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the driver flow destination struct to use bit flags with the vhca
id valid being the 1st one. The flags field is more extendable and will
be used in downstream patch.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit
key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l).
Define the two key parsing alternatives in a union, thus enabling both
access methods.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support a new hardware module status in port module events:
- module_status=0x4 (Cable plugged, but disabled)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support a new hardware error type in port module events:
- error_type=0xc (PCIe system power slot exceeded)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add explicit HW defined error values. For simplicity, keep counters for all
statuses starting from 0, although currently status=0 is not used.
Additionally, when HW signals an unexpected cable status, it is reported
now rather than ignored. And status counter is now updated on errors.
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following gcc warning:
drivers/net/ipvlan/ipvlan_main.c:543:12: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'mode' is a u16 variable, IPVLAN_MODE_L2 is zero,
the comparison is always false
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a msg string, fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
