HP Elite Presenter Mouse HID Record Descriptor shows
two mouses (Repord ID 0x1 and 0x2), one keypad (Report ID 0x5),
two Consumer Controls (Report IDs 0x6 and 0x3).
Previous to this commit it registers one mouse, one keypad
and one Consumer Control, and it was usable only as a
digitl laser pointer (one of the two mouses). This patch defines
the 464a USB device ID and enables the HID_QUIRK_MULTI_INPUT
quirk for it, allowing to use the device both as a mouse
and a digital laser pointer.
Signed-off-by: Marco Morandini <marco.morandini@polimi.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Supports the Thunderstrike (SHIELD 2017) controller. Implements support for
the Thunderstrike HOSTCMD firmware interface. Adds sysfs attributes about a
SHIELD device and introduces haptics support for controllers.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, rumble is only supported via bluetooth on a single xbox
controller, called 'model 1708'. On the back of the device, it's named
'wireless controller for xbox one'. However, in 2021, Microsoft released
a firmware update for this controller. As part of this update, the HID
descriptor of the device changed. The product ID was also changed from
0x02fd to 0x0b20. On this controller, rumble was supported via
hid-microsoft, which matched against the old product id (0x02fd). As a
result, the firmware update broke rumble support on this controller.
See:
https://news.xbox.com/en-us/2021/09/08/xbox-controller-firmware-update-rolling-out-to-insiders-starting-today/
The hid-microsoft driver actually supports rumble on the new firmware,
as well. So simply adding new product id is sufficient to bring back
this support.
After discussing further with the xbox team, it was pointed out that
another xbox controller, xbox elite series 2, can be supported in a
similar way.
Add rumble support for all of these devices in this patch. Two of the
devices have received firmware updates that caused their product id's to
change. Both old and new firmware versions of these devices were tested.
The tested controllers are:
1. 'wireless controller for xbox one', model 1708
2. 'xbox wireless controller', model 1914. This is also sometimes
referred to as 'xbox series S|X'.
3. 'elite series 2', model 1797.
The tested configurations are:
1. model 1708, pid 0x02fd (old firmware)
2. model 1708, pid 0x0b20 (new firmware)
3. model 1914, pid 0x0b13
4. model 1797, pid 0x0b05 (old firmware)
5. model 1797, pid 0x0b22 (new firmware)
I verified rumble support on both bluetooth and usb.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Siarhei Vishniakou <svv@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the ROG Z13 keyboard. This is a variant of the last
few ASUS ROG keyboards and has much of the same functionality.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ignore the reported battery level of the built-in touchscreen to suppress
battery warnings when a stylus is used. The device ID was added and the
battery ignore quirk was enabled.
Signed-off-by: weiliang1503 <weiliang1503@gmail.com>
Link: https://lore.kernel.org/r/20230330115638.16146-1-weiliang1503@gmail.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Physical data for all kye tablets are collected from Windows driver, to
generate correct HID reports.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The tenkeyless version of the Realforce R2 has the same issue of the
full size one, the report fixup is needed to make n-key rollover
work instead of 6 key rollover
Signed-off-by: Alessandro Manca <crizan.git@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to many other devices using the Synopsys Designware Elantech
hardware, HP Spectre x360 13t-aw100 and 14t-ea100 report an empty
battery devices, supposedly for the active stylus.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore the battery reports
from these devices. Note that there are multiple versions of the panel
installed in the 14t-ea100.
Signed-off-by: Philippe Troin <phil@fifi.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For now only supports one model and only filters out bogus reports sent
when the keyboard has been configured through hidraw.
Without this, as events are not released, soft repeat floods userspace
with unknown key events.
Signed-off-by: Philippe Valembois <lephilousophe@gmail.com>
Link: https://lore.kernel.org/r/20230125211511.12266-1-lephilousophe@gmail.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The touchscreen reports a battery status of 0% and jumps to 1% when a
stylus is used. The device ID was added and the battery ignore quirk was
enabled for it.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Link: https://lore.kernel.org/r/20230120223741.3007-1-l.guzenko@web.de
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add preliminary support for the Steam Deck's controller interface. Currently,
this only supports the controller inputs and toggling lizard mode (Valve's name
for a hardware kb/m emulation mode). It does not support any of the advanced
features, such as the motion sensors or force-feedback.
The Steam Deck also includes a heartbeat for lizard mode that switches it back
on if no reports have been received within a few milliseconds. The official
Steam client handles this by sending a handful of configuration reports every
few ms, so we copy this behavior by sending configuration reports to disable
the mouse and reset the digital mappings every 5ms. As this isn't needed for
the older Steam Controller, this is only done on the Steam Deck.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20230126030126.895670-2-vi@endrift.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This device has a touchscreen thats report a battery even if it doesn't
have one.
Ask Linux to ignore the battery so it will not always report it as low.
[jkosina@suse.cz: fix whitespace damage]
Signed-off-by: Marco Rodolfi <marco.rodolfi@tuta.io>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make function buttons on ELECOM M-HT1DRBK trackball mouse work. This model
has two devices with different device IDs (010D and 011C). Both of
them misreports the number of buttons as 5 in the report descriptor, even
though they have 8 buttons. hid-elecom overwrites the report to fix them,
but supports only on 010D and does not work on 011C. This patch fixes
011C in the similar way but with specialized position parameters.
In fact, it is sufficient to rewrite only 17th byte (05 -> 08). However I
followed the existing way.
Signed-off-by: Takahiro Fujii <fujii@xaxxi.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco Pro MW is a UGEE v2 device with a frame with 8 buttons,
a bitmap dial and a mouse. Its pen has 2 buttons, supports tilt and
pressure.
It can be connected using a USB cable or, to use it in wireless mode,
using a USB Bluetooth dongle. When it is connected in wireless mode the
device battery is used to power it.
All the pieces to support it are already in place. Add its ID and
quirks in order to support the device.
Link: https://github.com/DIGImend/digimend-kernel-drivers/issues/622
Tested-by: Andreas Grosse <andig.mail@t-online.de>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco Pro SW is a UGEE v2 device with a frame with 8 buttons,
a bitmap dial and a mouse; however, the UCLOGIC_MOUSE_FRAME_QUIRK is
required because it reports an incorrect frame type. Its pen has 2
buttons, supports tilt and pressure.
It can be connected using a USB cable or, to use it in wireless mode,
using a USB Bluetooth dongle. When it is connected in wireless mode the
device battery is used to power it.
All the pieces to support it are already in place. Add its ID and
quirks in order to support the device.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco 01 V2 is a UGEE v2 device with a frame with 8 buttons.
Its pen has 2 buttons, supports tilt and pressure.
Add its ID in order to support the device.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/839
Tested-by: Mark Waddoups <mwaddoups@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This partially reverts commit f6d910a89a ("HID: usbhid: Add ALWAYS_POLL quirk
for some mice"), as it turns out to break reboot on some platforms for reason
yet to be understood.
Fixes: f6d910a89a ("HID: usbhid: Add ALWAYS_POLL quirk for some mice")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I no longer work for Plantronics (aka Poly, aka HP) and do not have
access to the headsets in order to test. However, as noted by Maxim,
the other 32xx models that share the same base code set as the 3220
would need the same quirk. This patch adds the PIDs for the rest of
the Blackwire 32XX product family that require the quirk.
Plantronics Blackwire 3210 Series (047f:c055)
Plantronics Blackwire 3215 Series (047f:c057)
Plantronics Blackwire 3225 Series (047f:c058)
Quote from previous patch by Maxim Mikityanskiy
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
End quote
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status is reported for the HP Envy x360 eu0009nv stylus even
though it does not have battery.
Prevent it from always reporting the battery as low (1%).
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/823
Reported-by: Ioannis Iliopoulos <jxftw2424@gmail.com>
Tested-by: Ioannis Iliopoulos <jxftw2424@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some additional USB mouse devices are needing ALWAYS_POLL quirk without
which they disconnect and reconnect every 60s.
Add below devices to the known quirk list.
CHERRY VID 0x046a, PID 0x000c
MICROSOFT VID 0x045e, PID 0x0783
PRIMAX VID 0x0461, PID 0x4e2a
Signed-off-by: Ankit Patel <anpatel@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Acer Aspire Switch V 10 (SW5-017)'s keyboard-dock uses the same
ITE controller setup as other Acer Switch 2-in-1's.
This needs special handling for the wifi on/off toggle hotkey as well as
to properly report touchpad on/off keypresses.
Add the USB-ids for the SW5-017's keyboard-dock with a quirk setting of
QUIRK_TOUCHPAD_ON_OFF_REPORT to fix both issues.
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MadCatz variant of the MMO7 mouse has the ID 0738:1713 and the same
quirks as the Saitek variant.
Signed-off-by: Samuel Bailey <samuel.bailey1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide initial support for the DualSense Edge controller. The brings
support up to the level of the original DualSense, but won't yet provide
support for new features (e.g. reprogrammable buttons).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
CC: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-3-roderick.colenbrander@sony.com
The Topre REALFORCE R2 firmware incorrectly reports that interface
descriptor number 1, input report descriptor 2's events are array events
rather than variable events. That particular report descriptor is used
to report keypresses when there are more than 6 keys held at a time.
This bug prevents events from this interface from being registered
properly, so only 6 keypresses (from a different interface) can be
registered at once, rather than full n-key rollover.
This commit fixes the bug by setting the correct value in a report_fixup
function.
The original bug report can be found here:
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/804
Thanks to Benjamin Tissoires for diagnosing the issue with the report
descriptor.
Signed-off-by: Harry Stern <harry@harrystern.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220911003614.297613-1-harry@harrystern.net
The touchbar on Apple T2 Macs has 2 modes, one that shows the function
keys and other that shows the media controls. The user can use the fn
key on his keyboard to switch between the 2 modes.
On Linux, if people were using an external keyboard or mouse, the
touchbar failed to change modes on pressing the fn key with the following
in dmesg :-
[ 10.661445] apple-ib-als 0003:05AC:8262.0001: : USB HID v1.01 Device [Apple Inc. Ambient Light Sensor] on usb-bce-vhci-3/input0
[ 11.830992] apple-ib-touchbar 0003:05AC:8302.0007: input: USB HID v1.01 Keyboard [Apple Inc. Touch Bar Display] on usb-bce-vhci-6/input0
[ 12.139407] apple-ib-touchbar 0003:05AC:8102.0008: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input0
[ 12.211824] apple-ib-touchbar 0003:05AC:8102.0009: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input1
[ 14.219759] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 24.395670] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 34.635791] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 269.579233] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 1 (-110)
Add the USB IDs of the touchbar found in T2 Macs to HID have special
driver list to fix the issue.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the Surface Go devices, the Elantech touchscreen/digitizer in
the Lenovo Yoga C630 mistakenly reports the battery of the stylus, and
always reports an empty battery.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore this battery and
prevent the erroneous low battery warnings.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Parblo A610 PRO is a UGEE v2 device with a frame with 9 buttons
and a bitmap dial. Its pen has 2 buttons, supports tilt and pressure.
Add its ID in order to support the device.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco Pro S is a UGEE v2 device with a frame with 8 buttons,
a bitmap dial and a mouse. Its pen has 2 buttons, supports tilt and
pressure.
All the pieces to support it are already in place. Add its ID in order
to support the device.
The required Wireshark traces were captured by Jouke Witteveen.
For more information check [1].
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/738 [1]
Tested-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco L (UGEE) needs to be initialized by sending a buffer of
magic data, discovered by sniffing the Windows driver traffic.
In order to differentiate UGEE tablets that need this kind of
initialization from the previous ones, name them v2 internally and
create an entry point for them.
After initialization, the template report descriptors can be discovered
by parsing a string descriptor, similar to the one exposed by HUION v1
devices.
Add all the required elements to support the device.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the Surface Go (1), the (Elantech) touchscreen/digitizer in
the Surface Go 2 mistakenly reports the battery of the stylus. Instead
of over the touchscreen device, battery information is provided via
bluetooth and the touchscreen device reports an empty battery.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore this battery and
prevent the erroneous low battery warnings.
Cc: stable@vger.kernel.org
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to other UGEE pens, but the IDs were missing.
Signed-off-by: Roman Romanenko <romu4444@gmail.com>
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for one of the several Mega World USB game
controller with integrated force feedback. It is a HID based
memory-less game controller, with a weak motor on the left, and a
strong one on the right.
Signed-off-by: frank zago <frank@zago.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
