The b44 Enet control disable bit may take longer to clear on some
systems, so the loop count is increased with this patch. Functionality
is not compromised, but a debug message can be seen when the bit is not
cleared within the count value.
Thanks to Vasileios Lourdas who reported the problem.
Signed-off by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By reading the MAC status register we can detect whether the MAC has
seen the PHY see link. This allows us to show the link properties before
the device is up in ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that 2.6.19 provides a proper implementation that saves MSI, PCI-E
config space, we can have the e1000 driver use those instead of it's
custom implementation.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use ARRAY_SIZE macro already defined in kernel.h for ATM
drivers.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The modifications and bug fixes noted below were done by Realtime Control
Works and Contemporary Control Systems, Inc, Jan 2005. They were
incorporated into the 2.6 kernel by Jeff Morrow of Sierra Analytics, Feb
2007. <jmorrow@massspec.com>
The changes have been tested on a Contemporary Controls PCI20U-4000.
Summary of changes:
Arc-rawmode.c:
rx():
- Fixed error in received packet lengths; 256 byte packets were
being received as 257 bytes packets.
prepare_tx():
- Fixed error in transmit length calcs; 257 byte packets were being
transmitted as 260 byte packets.
com20020.c:
com20020_check():
- We now load the SETUP2 register if the 'clockm' parameter is
non-zero, instead of checking for ARC_CAN_10MBIT. The user is
now responsible for whether or not SETUP2 is loaded. If the
clock multiplier is non-zero, this means that the user wants a
baud rate greater than 2.5Mbps. This is not possible unless the
SETUP2 register is present (COM20020D, or COM20022). So, we're
relying on the user to be smart about what kind of chip he's
dealing with...
com20020-pci.c
- Added several entries to com20020pci_id_table[].
Signed-off-by: Jeff Morrow <jmorrow@massspec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After being the defacto maintainer for a couple of years, I can now become the official maintainer.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove spin_lock_irqsave() around mii_ethtool_gset, mii_ethtool_sset
and generic_mii_ioctl. These are unnecessary and harmful because
the mii calls may call back into the mdio functions, which may sleep.
Pointed out by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't drop oversize frame it might be a VLAN (untagged).
Use different counter for fifo overrun vs fifo error.
Print error on fifo overrrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit timeout code could hang, and it would not clear out
problems if the hardware was stuck. Change the code to effectively do
a device down/up similar to the suspend/resume code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon-FE chip doesn't do gigabit and has a differen PHY internally.
On this chip, phy status register doesn't properly reflect the result
of flow control negotiation. To workaround the problem and avoid having
to have so much chip dependent code; compute the result of flow control
by looking at the local and remote advertised bits.
Signed-off-by: Stephen Hemmminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resetting the pause bits on shutdown is not necessary.
The code was inherited from the vendor driver, and it is currently #ifdef'd
out there as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't mark pause frames as errors. This problem caused transmitter not
to pause and would effectively take out a gigabit switch because the
it can't handle overrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyrights in the cxgb3 driver.
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was hardly necessary to repeat most of the code from gfar_error() in
gfar_interrupt(), especially having some inconsistencies between the two.
So, make the gfar_interrupt() just call gfar_error(), and not acknowledge
the interrupts itself as gfar_{receive/transmit/error}() do it anyway.
While at it, also clarify/cleanup debug messages in gfar_error()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pci_module_init() to pci_register_driver().
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add device id for the Attansic L1 chip to pci_ids.h, then use it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused define from atl1_main.c.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some Asus motherboards containing the L1 NIC, the MAC address is
written by the BIOS directly to the MAC register during POST, and is
not stored in eeprom. If we don't succeed in fetching the MAC address
from eeprom or spi, try reading it directly from the MAC register.
Suggested by Xiong Huang.
And do some cleanup while we've got the hood up...
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An ioread32 statement reads the wrong address. Fix it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The atl1 driver doesn't need NET_PCI. Remove it from Kconfig.
Noticed by Chad Sprouse.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a follow up for the patch providing the base support for the
ns9xxx machine type.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2443_PM is not defined in our Kconfig, so
remove the reference from CPU_S3C2443 to stop
the configuration process warning about it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Change I/O scheduler description to correctly show CFQ as being the default
scheduler and not the anticipatory scheduler that previously was default.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Mikael Pettersson pointed out to me that a recent patch of mine (commit
620034c84d), that made some corrections to the
README file, accidentally listed the Cris architecture twice. Whoops.
This patch removes the duplicate.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Some people are confused about maxcpus=1 and maxcpus=0,
so put the documentation text from init/main.c into
Documentation/kernel-parameters.txt also.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Found a couple of typos in the Documentation/driver-model/platform.txt
file. This patch fixes both of them.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
