that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
this will make sure that we execute at least once.
No functional changes otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
re-factor the common parts to a separate function,
so that code is easier to read and understand.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.
This last part will be done on another patch.
While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.
Code snippet (extremely simplified):
if (stat & NACK) {
...
omap_i2c_ack_stat(dev, stat & NACK);
}
if (stat & RDR) {
...
omap_i2c_ack_stat(dev, stat & RDR);
}
and so on. The tricky place is only WRT errata handling, for example:
if (*stat & (NACK | AL)) {
omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
...
}
but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.
Another tricky place is RDR | RRDY (likewise for XDR | XRDY):
if (stat & (RDR | RRDY)) {
...
omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}
again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch to aid readability. No functional
changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)
if (dev->buf_len) {
aaa;
} else {
bbb;
break;
}
to
if (!dev->buf_len) {
bbb;
break;
}
aaa;
Hence no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch, no functional changes
If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
drivers/i2c/busses/i2c-omap.c:1025: warning: assignment discards qualifiers from pointer target type
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
In omap_i2c_xfer(), ensure pm_runtime_put() is called, even on
failure.
Without this, after a failed xfer, the runtime PM usecount will have
been incremented, but not decremented causing the usecount to never
reach zero after a failure. This keeps the device always runtime PM
enabled which keeps the enclosing power domain active, and prevents
full-chip retention/off from happening during idle.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
Generate a stop condition after each message marked with I2C_M_STOP.
[JD: Add I2C_FUNC_PROTOCOL_MANGLING.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The OMAP3530 is based upon the same silicon as the OMAP3430 and so the I2C
revision is the same for 3430 and 3530. However, the OMAP3630 device has the
same I2C revision as OMAP4. Correct the revision definition to reflect this.
This patch is based on work done by Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Update OMAP_I2C_REV_ON_3430 also to reflect that it is same as 3530
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use INIT_COMPLETION instead of init_completion in transfer.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use SET_RUNTIME_PM_OPS macro to set runtime functions.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The omap_i2c_remove function may not be needed after
device exit so the memory could be freed.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On a board with OMAP3 processor and TWL4030 Power management,
we need to talk to the TWL4030 during late suspend but cannot
because the I2C interrupt is disabled (as late suspend disables
interrupt).
e.g. I get messages like:
[ 62.161102] musb-omap2430 musb-omap2430: LATE power domain suspend
[ 63.167205] omap_i2c omap_i2c.1: controller timed out
[ 63.183044] twl: i2c_read failed to transfer all messages
[ 64.182861] omap_i2c omap_i2c.1: controller timed out
[ 64.198455] twl: i2c_write failed to transfer all messages
[ 65.198455] omap_i2c omap_i2c.1: controller timed out
[ 65.203765] twl: i2c_write failed to transfer all messages
The stack shows omap2430_runtime_suspend calling twl4030_set_suspend
which tries to power-down the USB PHY (twl4030_phy_suspend ->
twl4030_phy_power -> __twl4030_phy_power which as a nice WARN_ON
that helps).
Then we get the same in resume:
[ 69.603912] musb-omap2430 musb-omap2430: EARLY power domain resume
[ 70.610473] omap_i2c omap_i2c.1: controller timed out
[ 70.626129] twl: i2c_write failed to transfer all messages
etc.
So don't disable interrupts for I2C.
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The section number in the recent errata document has changed.
Rename the erratum 1p153 to the unique id i462 instead, so that
it is easier to reference. Also change the function name and comments
to reflect the same.
Cc: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently in the 1.153 errata handling, while waiting for transmitter
underflow, if NACK is got the XUDF(Transmit underflow) flag is also set.
Fix this by setting the XUDF(Transmit underflow) flag after wait for the
condition is over.
Cc: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Moiz Sonasath <m-sonasath@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c_probe set the dev->errata flag, but omap_i2c_init cleared the flag again.
Prevent the overwrite of the errata flags.Move the errata handling to a unified
place in probe to prevent such errors.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If PM runtime get_sync fails return with the error
so that no further reads/writes goes through the interface.
This will avoid possible abort. Add a error message in case
of failure with the cause of the failure.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
By definition, wait_for_completion_timeout() returns an unsigned value and
therefore, it is not necessary to check if the return value is less than zero
as this is not possible.
This is based on a patch from Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Declare a long as the wait_for_completion_timeout returns long.
Original patch is
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=ea02cece7b0000bc736e60c4188a11aaa74bc6e6
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently in probe
pm_runtime_put(dev->dev);
...
/* i2c device drivers may be active on return from add_adapter() */
adap->nr = pdev->id;
r = i2c_add_numbered_adapter(adap);
if (r) {
dev_err(dev->dev, "failure adding adapter\n");
goto err_free_irq;
}
...
return 0;
err_free_irq:
free_irq(dev->irq, dev);
err_unuse_clocks:
omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
pm_runtime_put(dev->dev);
This may access the i2c registers without the clocks in the error cases.
Fix the same by moving the pm_runtime_put after the error check.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On OMAP4 we were writing 1 to IRQENABLE_CLR which cleared only
the arbitration lost interrupt. The patch intends to fix the same by writing 0
to the IE register clearing all interrupts.
This is based on the work done by Vikram Pandita <vikram.pandita@ti.com>.
The changes from the original patch ...
- Does not use the IRQENABLE_CLR register to clear as it is not mentioned
to be legacy register IRQENABLE_CLR helps in atomically
setting/clearing specific interrupts, instead use the OMAP_I2C_IE_REG as we
are clearing all interrupts.
Cc: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently the i2c driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.Fix the same by calling
pm_runtime_disable in the error and the remove path.
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The functions omap_i2c_unidle/idle are called from omap_i2c_runtime_resume
and omap_i2c_runtime_suspend which is compiled for CONFIG_PM_RUNTIME.
This patch removes the omap_i2c_unidle/idle functions and folds them
into the runtime callbacks.
This fixes the below warn when CONFIG_PM_RUNTIME is not defined
CC arch/arm/mach-omap2/board-ti8168evm.o
drivers/i2c/busses/i2c-omap.c:272: warning: 'omap_i2c_unidle' defined but not used
drivers/i2c/busses/i2c-omap.c:293: warning: 'omap_i2c_idle' defined but not used
CC net/ipv4/ip_forward.o
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
CONFIG_OF is not defined for OMAP1 yet and thus the omap1_defconfig build
generate an error for 3.3-rc1.
drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
drivers/i2c/busses/i2c-omap.c:1021:26: error: 'omap_i2c_of_match' undeclared (first use in this function)
drivers/i2c/busses/i2c-omap.c:1021:26: note: each undeclared identifier is reported only once for each function it appears in
Wrap omap_i2c_of_match with of_match_ptr() to prevent compilation error in case of OMAP1 build.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add initial DT support to retrieve the frequency using a
DT attribute instead of the pdata pointer if of_node exist.
Add documentation for omap i2c controller binding.
Based on original patches from Manju and Grant.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4 OMAP_I2C_STAT_NACK is causing a timeout on the next access.
The isr cleans all flags in OMAP_I2C_CON_REG by setting OMAP_I2C_CON_STP
OMAP_I2C_CON_STP is also set in omap_i2c_xfer_msg on the last message.
According to the TI TSR the sequence for OMAP_I2C_STAT_NACK and
OMAP_I2C_STAT_AL are nearly the same.
Removing the OMAP_I2C_CON_STP part in the isr fix the problem.
Tested on OMAP4430 and OMAP3530 (here NACK was not a problem)
Fixes also booting on 2430sdp.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently the fifo depth is set to zero for OMAP4 which disables
the FIFO usage. This patch enables the FIFO usage for I2C transactions
on OMAP4 also.
Tested on omap4430 and 3430.
Tested-and-Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Current usage of runtime PM is not quite correct. The actual
idle/unidle of the I2C hardware should not happen until the runtime PM
callbacks are called. Therefore, change omap_i2c_[un]idle() functions
to only be called from the runtime PM callbacks (when usage count
transitions to/from zero.)
Also, the runtime PM core does usage counting and replaces
functionality currently managed by the dev->idle flag. Remove usage
of dev->idle in favor of using runtime PM, and checking status using
pm_runtime_suspended().
Signed-off-by: Kevin Hilman <khilman@ti.com>
A pointer to the struct device associated with the i2c device is
already kept in the struct omap_i2c_dev, so use omap_i2c_device to
find the pointer to struct device.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently for OMAP4 the I2C_WE is not programmed.
This patch enables the programming for OMAP4.
This patch fixes a bad conflict resolution.
This effectively restores the following commit
Commit 120bdaa47[i2c-omap: Program I2C_WE on OMAP4 to enable i2c wakeup]
which got changed by
Commit a3a7acbc[I2C: OMAP2+: address confused probed version naming]
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The IP version is prepended to the existing printed probed
version as an "epoch" version.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch eliminates all cpu_...() tests from the OMAP I2C driver.
Instead, it uses the functionality flags in the platform data to make
the decisions about product variations the driver needs to handle.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The driver reflects the confusion that probed I2C revision
from the hardware of 0x40 means it is on an OMAP4430.
However, you will probe the same 0x40 ID on an OMAP3530. So
this patch changes the name to reflect that.
It also clarifies that the original name OMAP_I2C_REV_2 is
referring to some ancient OMAP1 revision number, not to be
confused with the IP revisions this patch series introduces.
Similarly the term "rev" is used in the ancient OMAP1 ISR,
the term is changed to use omap1 instead.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This solves the main problem the patch series is about. Prior
to this patch on OMAP3530 the driver wrongly interprets the I2C
peripheral unit's own reported revision as meaning it is running
on an IP V2 device and must use the extended registers.
In fact OMAP3530 is IP V1 with the smaller register set, the
reason for the confusion is that the hardware does in fact report
having the same IP revision index as is found on an OMAP4430,
which really is IP V2 and has the extended registers.
This corrects the test for which registers to use so that it
decides using hwmod knowledge found in the platform_data.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Change the register map names to reflect the IP revision they
are representing, and use the platform_data IP revision index
to select between them at init time.
Eliminates 1 of 17 cpu_...() calls in the driver.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP I2C driver dynamically chooses between two register sets of
differing sizes depending on the cpu type it finds itself on.
It has been observed that the existing code references non-existing
registers on OMAP3530, because while it correctly chose the smaller
register layout based on cpu type, the code uses the probed register
ID to decide if to execute code referencing an extra register, and
both register layout devices on OMAP3530 and OMAP4430 report the same
probed ID of 0x40.
This patch changes the extended register names only found on IP V2
of the I2C peripheral unit accordingly to help show up errors in usage.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This reverts commit adf6e07922.
Remove system PM methods which can race with runtime PM methods.
Also, as of v3.1, the PM domain level code for OMAP handles device
power state transistions automatically for devices, so drivers no
longer need to specifically call the bus/pm_domain methods themselves.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure that the 'static' keywork is at the beginning of declaration
for drivers/i2c/busses/i2c-omap.c
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.
This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch converts the i2c driver to use PM runtime apis
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
If the i2c bus receives an interrupt with both BB (bus busy) and
ARDY (register access ready) statuses set during the tranfer of the last message
the bus was put to idle while still busy.
This caused bus to timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Clean up existing Errata 1p153 handling to use generic
errata handling mechanism through dev flag.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Under certain rare conditions, I2C_STAT[13].RDR bit may be set
and the corresponding interrupt fire, even there is no data in
the receive FIFO, or the I2C data transfer is still ongoing.
These spurious RDR events must be ignored by the software.
This patch handles and ignores RDR spurious interrupts.
The below sequence is required in interrupt handler for
handling this errata:
1. If RDR is set to 1, clear RDR
2. Read I2C status register and check for BusBusy bit. If BusBusy
bit is set, skip remaining steps.
3. If BusBusy bit is not set, perform read operation on I2C status
register.
4. If RDR is set, clear the same. Check RDR again and clear if it sets
RDR bit again.
5. Perform I2C Data Read operation N number of times(where N is value
read from the register BUFSTAT-RXSTAT bit fields).
Note:
This errata is not applicable for omap2420 and omap4.
It is applicable for:
1. omap2430
2. omap34xx(including omap3630).
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Hema Kalliguddi <hemahk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The errata 1.153 workaround is busy waiting on XUDF bit in interrupt
context, which may lead to kernel hangs. The problem can be reproduced
by running the bus with wrong (too high) speed.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is to avoid insanely long lines and levels of indentation.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Cc: Nishant Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is rebased version of earlier post to add I2C
driver support to OMAP4 platform. On OMAP4, all
I2C register address offsets are changed from OMAP1/2/3 I2C.
In order to not have #ifdef's at various places in code,
as well as to support multi-OMAP build, an array is created
to hold the register addresses with it's offset.
This patch was submitted, reviewed and acked on mailing list
already. For more details refer below link
http://www.mail-archive.com/linux-i2c@vger.kernel.org/msg02281.html
This updated verion has a depedancy on "Add support for 16-bit registers"
posted on linux-omap. Below is the patch-works link for the same
http://patchwork.kernel.org/patch/72295/
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
A pointer to omap_i2c_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: chandra shekhar <x0044955@ti.com>
Cc: Jason P Marini <jason.marini@gmail.com>
Cc: Syed Mohammed Khasim <x0khasim@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices. However, OMAP730/850 based
devices use a 16-bit register size.
This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Tested on Zoom2, Zoom3, 3430SDP and 3630SDP
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: George, Harith<harith@ti.com>
Acked-by: Varadarajan, Charu Latha<charu@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Because of OMAP off-mode, powerdomain can go off when I2C is idle.
Save enough state, and do a re-init for each transfer.
Additional save/restore state added by Jagadeesh Bhaskar Pakaravoor
(SYSC_REG) and Aaro Koskinen (wakeup sources.)
Also, The OMAP3430 TRM states:
"During active mode (I2Ci.I2C_CON[15] I2C_EN bit is set to 1), make no
changes to the I2Ci.I2C_SCLL and I2Ci.I2C_SCLH registers. Changes may
result in unpredictable behavior."
Hence, the I2C_EN bit should be clearer when modifying these
registers. Please note that clearing the entire I2C_CON register to
disable the I2C module is safe, because the I2C_CON register is
re-configured for each transfer.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Jagadeesh Bhaskar Pakaravoor <j-pakaravoor@ti.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Hu Tao <taohu@motorola.com>
Cc: Xiaolong Chen <A21785@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.
Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.
Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes
http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.
On Interrupt: I2C_STAT[RDR],
read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Hi Ben,
Can you please queue this fix?
Thanks,
Tony
>From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 17 Jun 2009 13:14:23 +0300
Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430
Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430
instead. The typo was probably caused by a mismerge.
Without this patch all omaps fail to build with:
error: implicit declaration of function 'cpu_is_omap_2430'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This replace all instances in the i2c busses tree of
res->end - res->start + 1 with the handy macro resource_size(res)
from ioport.h (coming in from platform_device.h).
This was created with a simple
sed -i -e 's/\([a-z]*\)->end *- *[a-z]*->start *+ *1/resource_size(\1)/g'
Then manually replacing the PXA redefiniton of the same kind
of macro manually. Recompiled some ARM defconfigs I could find to
make a rough test so it shouldn't break anything, though I
couldn't see exactly which configs you need for all the drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On OMAP1, the I2C functional clock (fck) is the armxor_ck, so there's
no need to get "armxor_ck" separately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The probe function used a pointer to the interrupt
handler to register as a 'void *', change it to the
proper type of irq_handler_t.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2C_WE registers were not configured, which caused huge delays in
I2C operations while cpu idle was enabled and omap entered WFI.
This patch enables all I2C wakeup sources.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C controller clears its OCP_SYSCONFIG register after an OCP soft reset.
Reprogram OCP_SYSCONFIG for maximum power savings on rev3.6 controllers
and beyond. On 2430, this involves setting the module AUTOIDLE bit.
On 3430, this includes module AUTOIDLE, wakeup enable, slave smart-idle,
and considers only the module functional clock state for idle-ack.
Boot-tested on 2430SDP and 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i2c-omap discriminates only between "revision 1" or "greater than
revision 1." A following patch introduces code that must also
discriminate between rev2.x, rev3.6, and rev3.12 controllers. Support
this by storing the full revision data from the I2C_REV register, rather
than just a single bit.
The revision definitions may need to be extended for other ES levels
that aren't currently available here. rev3.6 is what's present on the
2430SDP here (unknown ES revision); rev3.12 is used on the 3430ES2
here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_i2c_unidle() and omap_i2c_idle() are called recursively during
omap_i2c_probe(). This is evidently unexpected and will wipe
out the I2C interrupt enable register the second time that
omap_i2c_idle() is called consecutively. Any I2C transactions
following a probe of a bus with at least one device on it will then
time out.
Fix by moving omap_i2c_idle() further up in omap_i2c_probe(). Ensure
the I2C controller is marked as idle before the probe starts. Also
attempt to catch future reappearances of this bug early in development
by warning in omap_i2c_{un,}idle() when they are called recursively.
Problem reported by David Brownell <david-b@pacbell.net>.
Tested on 3430SDP and 2430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by; Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Skip compiling OMAP15xx I2C ISR for non-OMAP15xx builds. Saves 400 bytes
of text for most OMAP builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch from Nishant Menon:
- Transfers can use FIFO on FIFO capable devices
- Prevents errors for HSI2C if FIFO is not used
- Implemented errenous handling of STT-STP handling on SDP2430
Also merged in is a fix from Jaron Marini to fix occasional i2c
hang if OMAP_I2C_CON_STT remains asserted.
Signed-off-by: Jason P Marini <jason.marini@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap2430 has additional support for high-speed I2C.
This patch moves I2C speed parameter (from module) to platform data.
Also added basic High Speed support based on I2C bus speed.
This patch is tested for high speed I2C (with TWL4030 Keypad) and works as
expected.
Also change the 2430 i2chs_fck names to use the standard naming.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_i2c_idle() sets an internal flag, "dev->idle", instructing its
ISR to decline interrupts. It sets this flag before it actually masks
the interrupts on the I2C controller. This is problematic, since an
I2C interrupt could arrive after dev->idle is set, but before the
interrupt source is masked. When this happens, Linux disables the I2C
controller's IRQ, causing all future transactions on the bus to fail.
Symptoms, happening on about 7% of boots:
irq 56: nobody cared (try booting with the "irqpoll" option)
<warning traceback here>
Disabling IRQ #56
i2c_omap i2c_omap.1: controller timed out
In omap_i2c_idle(), this patch sets dev->idle only after the interrupt
mask write to the I2C controller has left the ARM write buffer.
That's probably the major offender. For additional prophylaxis, in
omap_i2c_unidle(), the patch clears the dev->idle flag before
interrupts are enabled, rather than afterwards.
The patch has survived twenty-two reboots on the 3430SDP here without
wedging I2C1. Not absolutely dispositive, but promising!
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If there is a signal pending and wait_for_completion_interruptible_timeout
terminates with -ERESTARTSYS, we return and disable the i2c clocks in
omap_i2c_xfer.
If we terminate before sending last i2c message with a stop condition, the
bus remains busy and we are not able to send new messages into bus with
successive omap_i2c_xfer calls. Therefore a pending signal is not caught
here and we return only because of timeout or i2c error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
