When not using the i2c suspend/resume callbacks the i2c client resumed
before the i2c master.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On gta02 hardware revision A5 it can actually bring the system down
during normal operating conditions so we disable it.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding individual IRQs in each function which
manipulates them store data for IRQs in a table which is then
referenced in the users.
This is a substantial code shrink and should be a performance win in
cases where only a single IRQ goes off at once since instead of
reading four of the second level IRQ registers for each interrupt
we read only the sub-registers which have had an interrupt flagged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for refactoring - it's over 700 lines of well-isolated
code and having it in a file by itself makes things more managable.
While we're at it make sure that we clean up the IRQ if we fail after
acquiring it on init.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8607 depends on I2C and MFD_CORE. Since 88PM8607 is built-in
kernel, it also requires that I2C and MFD_CORE are built-in
kernel also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The function asic3_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8320 is an integrated power management subsystem providing
voltage regulators, RTC, watchdog and other functionality. The
WM8320 is derived from the WM831x and therefore shares most of
the driver code with the WM831x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Better support future device revisions by moving some of the output
around and making the chip ID enumeration be the value expected in
the ID register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The name field of struct i2c_client is for i2c-core's use, it should
never be changed by the drivers themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When building the driver as a module, module_exit was missing, and
subsys_initcall_sync() is not defined.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds core driver support for AB4500 mixed signal
multimedia & power management chip. This connects to U8500
on the SSP (pl022) and exports read/write functions for
the device to get access to this chip. This also registers
the client devices and sets the parent.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Reviewed-by: Mark Brown <broonie@sirena.org.uk>
Reviewed-by: Jean-Christophe <plagnioj@jcrosoft.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for 88PM8607 found in Marvell DKB development
platform. This driver is a proxy for all accesses to 88PM8607
sub-drivers which will be merged on top of this one, RTC, regulators,
battery and so on.
This chip is manufactured by Marvell.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
There was confusion between the array size and the highest ISEL
value possible.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds platform data with a function for power
control to the SDHI driver. The idea is that board specific
code can provide their own functions so power can be enabled
and disabled for the sd-cards.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since twl4030_probe is only called from functions in the init ELF
section, annotate it so.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows UCB1400 to get IRQ GPIO from platform data. In case
platform_data are not supplied or the IRQ supplied in the platform_data
is negative, fall back to the old IRQ detection algorithm.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The backup battery on WM831x is a separate IP block to the main PMU
and is largely unrelated to the main supply functionality. Factor it
out into a separate driver in order to reflect this and better support
future hardware versions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are mistakenly dereferencing twl->client in the twl->client null checking
path.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This avoids crashes when running without interrupt support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds an MFD driver for the SuperH Mobile SDHI
hardware block. At this point the driver simply wraps the
tmio-mmc driver with some clock code. In the future this
driver is the place to put SDHI specific hotplug code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
The usb regulator supplies (usb1v5, usb1v8 & usb3v1) must be available
before adding the twl4030_usb child, else twl4030_usb_ldo_init() will
always fail thus causing boot lock-up.
This patch fixes boot on OMAP systems using the twl4030 usb transceiver.
CONFIG_TWL4030_USB=y
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The ab3100 driver doesn't, so there is no
point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/mfd/ab3100-core.c:647: error: ab3100_init_settings causes a section type conflict
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of hand rolling our own variant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the regulators found in the AB3100
Mixed-Signal IC.
It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the sleep script is loaded before the wakeup script, there is a
chance that the system might go to sleep before the wakeup script
loading is completed. This will lead to a system that does not wakeup
and has been observed to cause non-booting boards.
Various options were considered to solve this problem, including
modification of the core twl4030 power code to be smart enough to
reorder the loading of the scripts. But it felt too over-engineered.
Hence this patch just warns the DPS script developer so that they may be
reordered in the board-code itself.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).
Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the ability to read out OTP (One-Time Programmable)
registers in the AB3100 MFD ASIC. It's a simple sysfs file you
can cat to prompt. The OTP registers of the AB3100 are used to
store various device-unique information such as customer ID,
product flags and the 3GPP standard IMEI (International Mobile
Equipment Indentity) number.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides the core Freescale MC13783 support. It
registers the client platform_devices and provides access
to the A/D converter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This will make the worker fire interrupt disable the AB3100 IRQ
without sync which resolves a race since the interrupt obviously
cannot wait for itself to complete while being handled.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This alters the default setting for AB3100_IMRB1 from 0xff to
0xbf. These registers are used for the yet unimplemented ADC
and this new setting will deactivate ADC Trigger 1.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This makes ab3100_set_register_interruptible() propagate the error
code from suboperations properly so it can be handles properly.
(A special case comes from signal interruption.)
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the _interruptible suffix to the AB3100 accessor
functions on par with mutex_lock_interruptible() that's used
for blocking simultaneous calls to the AB3100 acessor functions.
Since these accesses are slow on a 100kHz I2C bus and may line
up waiting for the mutex, we need to handle interruption by
system shutdown or kill signals and may just as well denote that
in the function names.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.
Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.
An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.
The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.
Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.
This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().
As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Register ezx-pcap earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch corrects the support for MMCSD card detection
and read only feature for SoC DM355.
EVMDM355_ECP_VA4.pdf, from Spectrum digital, suggests that
Bit 2 and 4 should be checked for card detection. However
on the EVM, bits 1 and 3 gives this status, for MMC/SD
instance 0 and 1 respectively. The pdf also suggests that
Bit 1 and 3 should be checked for write protection. However
on the EVM bits 2 and 4 gives this status.
This document can be downloaded from
http://c6000.spectrumdigital.com/evmdm355/reve/files/EVMDM355_ECP_VA4.pdf
Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current implementation is prone to races, this patch attempts to remove all
but one (in pcf50633_adc_sync_read).
The idea is that we need to guard the queue access only on inserting and
removing items. If we insert and there're no more items in the queue it
means that the last irq already happened and we need to trigger ADC
manually. If not, then the next conversion will be triggered by the irq
handler upon completion of the previous.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.
I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make that twl4030-pwrbutton.c driver probe with current
child creation api for twl4030.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mask interrupts before servicing them and loop while pcap asserts the interrupt
line.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030 IRQ handler has a bug which leads to spinlock lock-up. It is
calling the 'unmask' function in a process context. :The mask/unmask/ack
functions are only designed to be called from the IRQ handler code,
or the proper API interfaces found in linux/interrupt.h.
Also there is no need to have IRQ chaining mechanism. The right way to
handle this is to claim the parent interrupt as a standard interrupt
and arrange for handle_twl4030_pih to take care of the rest of the devices.
Mail thread on this issue can be found at:
http://marc.info/?l=linux-arm-kernel&m=124629940123396&w=2
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_mouse - use standard driver registration method
Input: mark serio and i8042 as suspended when hibernating too
Input: add support for generic GPIO-based matrix keypad
Input: arrange keyboards alphabetically
Input: gpio-keys - avoid possibility of sleeping in timer function
Input: gpio-keys - revert 'change timer to workqueue'
Input: dm355evm_keys - fix kconfig symbol names
Input: wacom - add DTF720a support and fix rotation on Intuos3
Input: i8042 - more reset quirks for MSI Wind-clone netbooks
The keypad driver for the DM355 EVM got slightly broken as it merged,
since it moved from input/keyboard to input/misc and its Kconfig
symbol changed. This patch copes with the changed Kconfig symbol.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implementation of twl4030 watchdog driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Atal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
For MFDs running regulator cores, we really want them to be brought up early
during boot.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the ASIC3's SD/SDIO MFD cell, supported by the tmio_mmc driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the ASIC3's DS1WM MFD cell, supported by the ds1wm driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This should make the code a little bit easier to read.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ASIC3 has to work on both PXA and S3C and since their
struct clk implementations differ, we can't register out
clocks with the clkdev mechanism (yet?).
For now we have to keep clock handling internal to this
driver and enable/disable the clocks via the
mfd_cell->enable/disable functions.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT
registers needed for DS1WM, MMC/SDIO and PCMCIA functionality.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.
It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.
This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users and remove the typedef.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No impact unless someone has written additional kernel code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Impact: Fix section mismatch.
clocks_init() has been called from twl4030_probe() which is a non-init
function. Since probing can be done anytime so clocks_init will be
called anytime too. So we mark clock_init() as non-init.
LD drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.text+0x8dd9): Section mismatch in
reference from the function twl4030_probe() to the function
.init.text:clocks_init()
The function twl4030_probe() references
the function __init clocks_init().
This is often because twl4030_probe lacks a __init
annotation or the annotation of clocks_init is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This includes the USB current limit status override which is used in the
power management driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
it's a little too large for static line.
The ts is currently the only mainline user but Marek Vasut claims that
there is a battery driver in an ARM tree which also needs this function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:
: commit 3aa551c9b4
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date: Mon Mar 23 18:28:15 2009 +0100
:
: genirq: add threaded interrupt handler support
:
: Add support for threaded interrupt handlers
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.
To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reverse the order of the tests for loop exit so we use a valid value
before we time out. Vanishingly unlikely to happen since we retry for
several times the expected conversion time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch makes htc-pasic3 register the DS1WM and LED cell drivers
through the MFD core infrastructure instead of allocating the platform
devices manually. It also calculates the bus_shift parameter from the
memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Some I2C controllers have high overheads for setting up I2C operations
which makes the register cache setup on startup excessively slow since
it does a lot of small transactions. Reduce this overhead by doing a
bulk read of the entire register bank and filtering out what we don't
need later.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Add VPLL2 to the set of twl4030-family regulators exposed for
use by various drivers. It's commonly used to power the digital
video outputs (e.g. LCD or DVI displays) on OMAP3 systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/mfd/built-in.o(.text+0x1706): Section mismatch in
reference from the function sm501_register_gpio() to the function
.devinit.text:sm501_gpio_register_chip()
The function sm501_register_gpio() references
the function __devinit sm501_gpio_register_chip().
This is often because sm501_register_gpio lacks a __devinit
annotation or the annotation of sm501_gpio_register_chip is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
drv => driver renaming is needed otherwise modpost will spit false positives
re pointing to __devinit function from regular data.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The i2c_device_id list is supposed to be zero-terminated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The IRQs might have been left enabled in hardware, generating spurious
IRQs before the drivers have registered.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Fixes an off-by-one error in the iomem resource mapping.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Many ARM platforms do not provide a mach/cpu.h so rather than guarding
the use of that header with CONFIG_ARM guard it with the guards used
when testing for the OMAP variants in the body of the code.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
With a postfix decrement tries will reach -1 rather than 0,
so the warning will not be issued even upon timeout.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The code is out of sync with the silicon.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Check the return value of the device I/O functions when reading the
ID registers so we can provide a more useful diagnostic when we're
having trouble talking to the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Ensure that the interrupt handling is configured before we do platform
specific init. This allows the platform specific initialisation to
configure things which use interrupts safely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since ei is already known to be non-NULL, I assume that what was intended
was to test the result of kzalloc.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Remove references to set_irq_type and handle_level_irq which are not exported
to modules
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
TWL4030: fix clk API usage
[ARM] 5364/1: allow flush_ioremap_region() to be used from modules
[ARM] w90x900: fix build errors and warnings
[ARM] i.MX add missing include
[ARM] i.MX: fix breakage from commit 278892736e
[ARM] i.MX: remove LCDC controller register definitions from imx-regs.h
Always pass a struct device if one is available; and there's really
no reason for the processor specific stuff in this file if only
people would follow the API usage properly by using the struct device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes:
drivers/mfd/twl4030-core.c:657: error: implicit declaration of function
'cpu_is_omap2430'
Not the nicest fix, but this should be improved by a better OMAP clock API
implementation.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
When setting an GPIO to either input or output, we
should ensure that the pin configuration elsewhere
in the chip is set to GPIO in-case the initial
setup has not been done correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Support card detect and writeprotect switches on DM355 EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.
Since we don't have adc subsystem, it currently lives in drivers/mfd.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: Jonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver. This driver
implements support for this within the standard LED class.
Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver. The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.
This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The subdevice removal functions are marked __devexit but are referenced
from the error handling path when probing so are needed even when
__devexit functions are removed.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
ove the menelaus driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP2 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Move the tps65010 driver from drivers/i2c/chips to drivers/mfd
since it's more of a multi-function device than anything else,
and since Jean is trying to vanish drivers/i2c/chips ASAP.
One way to think of these chips are as the PMIC family most
used with OMAP1 generation chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:
- Provides an interface for other drivers: register read/write
utilities, and register declarations.
- Directly exports:
* Many signals through the GPIO framework
+ LEDs
+ SW6 through gpio sysfs
+ NTSC/nPAL jumper through gpio sysfs
+ ... more could be added later, e.g. MMC signals
* Child devices:
+ LEDs, via leds-gpio child (and default triggers)
+ RTC, via rtc-dm355evm child device
+ Buttons and IR control, via dm355evm_keys
- Supports power-off system call. Use the reset button to power
the board back up; the power supply LED will be on, but the
MSP430 waits to re-activate the regulators.
- On probe() this:
* Announces firmware revision
* Turns off the banked LEDs
* Exports the resources noted above
* Hooks the power-off support
* Muxes tvp5146 -or- imager for video input
Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.
This completely ignores the registers reporting the output voltages
on the various power supplies. Someone could add a hwmon interface
if that seems useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The global irq_desc array is soon going to be accessible only with
!CONFIG_SPARSE_IRQ. We should start using the generic irq_to_desc()
routines instead.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Register a child device for the codec in the WM8400.
Also switch the unregistration of the MFD devices to use the MFD core
since the current code is hand rolling the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The MFD cell structure provides a driver_data field but doesn't pass it
on to the child devices when instantiating them - do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This is a fix for:
twl4030-core.c:(.text+0x16a797): undefined reference to `clk_get_rate'
twl4030-core.c:(.text+0x16a797): undefined reference to `clk_put'
on x86 and x86_64, as the clock API is not defined on those platforms.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This contains two bugfixes to the initial twl4030 regulator
support patch related to USB:
(a) always overwrite the old list of consumers ... else
the regulator handles all use the same "usb1v5" name;
(b) don't set up the "usbcp" regulator, which turns out
to be managed through separate controls, usually ULPI
directly from the OTG controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Initial code to create twl4030 voltage regulator devices, using
the new regulator framework. Note that this now starts to care
what name is used to declare the TWL chip:
- TWL4030 is the "old" chip; newer ones have a bigger variety
of VAUX2 voltages.
- TWL5030 is the core "new" chip; TPS65950 is its catalog version.
- The TPS65930 and TPS65920 are cost-reduced catalog versions of
TWL5030 parts ... fewer regulators, no battery charger, etc.
Board-specific regulator configuration should be provided, listing
which regulators are used and their constraints (e.g. 1.8V only).
Code that could ("should"?) leverage the regulator stuff includes
TWL4030 USB transceiver support and MMC glue, LCD support for the
3430SDP and Labrador boards, and S-Video output.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Finish removing dependency of TWL driver stack on platform-specific
IRQ definitions ... and remove the build dependency on OMAP.
This lets the TWL4030 code be included in test builds for most
platforms, and will make it easier for non-OMAP folk to update
most of this code for new APIs etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Minor cleanup to twl4030-core: define a helper function to populate
a single child node, and use it to replace six inconsistent versions
of the same logic. Both object and source code shrink.
As part of this, some devices now have more IRQ resources: battery
charger, keypad, ADC, and USB transceiver. That helps to remove some
irq #defines that block the children's drivers code from compiling on
non-OMAP platforms.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since the WM8350 driver was originally written the semantics for the
identification registers of the chip have been clarified, allowing
us to do an exact match on all the fields. This avoids mistakenly
running on unsupported hardware.
Also change to using the datasheet names more consistently for
legibility and fix a printk() that should be dev_err().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Minor change to the TWL4030 utility interface: support reads
of all 256 bytes in each register bank (vs just 255). This
can help when debugging, but is otherwise a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The auxiliary ADC in the WM8350 is shared between several subdevices
so access to it needs to be arbitrated by the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
No other software changes are required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Hopefully this will make the purpose of these functions a bit clearer,
it's not immediately obvious that the lock is a hardware feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
There's no need to read this back from the chip each time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton, remove memzero() - it's not supported
on other architectures so use of it is a potential build breaking bug.
Since the compiler optimizes memset(x,0,n) to __memzero() perfectly
well, we don't miss out on the underlying benefits of memzero().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The vendor BSP used for the WM8350 development provided an I2C driver
which incorrectly returned zero on succesful sends rather than the
number of transmitted bytes, an error which was then propagated into the
WM8350 I2C accessors.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Otherwise we could build in WM8400 but not I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
sm501_devdata->irq is unsigned, while platform_get_irq() returns a
signed int.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Use the newly introduced pci_ioremap_bar() function in drivers/mfd.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This makes the contents of the cache clearer and fixes incorrect
initialisation of the cache for partially volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
October 10th linux-next build (powerpc allyesconfig) failed like this:
drivers/mfd/wm8350-core.c:1131: error: __ksymtab_wm8350_create_cache causes a section type conflict
Caused by commit 89b4012bef ("mfd: Core
support for the WM8350 AudioPlus PMIC"). wm8350_create_cache is not used
elsewhere, so remove the EXPORT_SYMBOL.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
- Move it into a separate file; clean and streamline it
- Restructure the init code for reuse during secondary dispatch
- Support both levels (primary, secondary) of IRQ dispatch
- Use a workqueue for irq mask/unmask and trigger configuration
Code for two subchips currently share that secondary handler code.
One is the power subchip; its IRQs are now handled by this core,
courtesy of this patch. The other is the GPIO module, which will
be supported through a later patch.
There are also minor changes to the header file, mostly related
to GPIO support; nothing yet in mainline cares about those. A
few references to OMAP-specific symbols are disabled; when they
can all be removed, the TWL4030 support ceases being OMAP-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
ia64 allmodconfig:
In file included from include/linux/ucb1400.h:27,
from drivers/mfd/ucb1400_core.c:24:
include/asm-generic/gpio.h: In function `gpio_get_value_cansleep':
include/asm-generic/gpio.h:147: error: implicit declaration of function `gpio_get_value'
include/asm-generic/gpio.h: In function `gpio_set_value_cansleep':
include/asm-generic/gpio.h:153: error: implicit declaration of function `gpio_set_value'
drivers/mfd/ucb1400_core.c: At top level:
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
NO_IRQ is only defined on some architectures - the general way to test
for an invalid IRQ in the modern kernel is by comparing with zero.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch updates the remaining two TMIO drivers to use the clock API
rather than callback hooks into platform code.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Simplify twl4030 IRQ handling by removing a needless custom flow
handler. The top level IRQs, from the PIH, are well suited for
handle_simple_irq() ... they can't be acked or masked.
Switching resolves some issues with how IRQs were dispatched.
Notably, abuse of desc->status, IRQ accounting, and handling
of various faults.
In short, use standard genirq code.
Drivers that request_irq() to the PIH will need to pay more
attention to things like setting IRQF_DISABLED (since it's
no longer ignored), and making I2C calls from handlers (you'll
need a lockdep workaround).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
DA9030 (a.k.a ARAVA) and DA9034 (a.k.a MICCO) are PMICs designed by
Dialog Semiconductor, usually found on PXA-based platforms. These
PMICs are I2C-based, multi-function devices, usually with LEDs, PWMs
for backlight, BUCKs and LDOs, ADCs and touchscreen controller (on
DA9034).
This is the base support for the I2C operations, event registration
and handling, sub-devices management.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds the core of the TWL4030 driver, which supports
chips including the TPS65950. These chips are multi-function; see
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Public specs are in the works. For now, the block diagram on
the second page of the datasheet is fairly informative.
There are some known issues with this core code. Most notably,
the IRQ dispatching needs simplification (to use more of genirq),
generalization (integrating support for secondary IRQ dispatch
as well as primary, and removing the build dependency on OMAP),
and then probably updating to leverage threaded IRQ support
(expected to arrive in mainline "soon").
Once the core is in mainline, drivers for other parts of this
chip can follow its lead and start swimming upstream too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Add support for tmiofb cell found in tc6393xb chip.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Add information regarding OHCI cell of the tc6393xb
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Make the default output of the SM501 driver to be less noisy wrt to
message that have low informational value, or simply should be debug.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch moves the allocation of the resources off the stack in
mfd_add_device().
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.
Preallocate 32 irq_desc, and irq_desc() will try to get more.
( No change in functionality is expected anywhere, except the odd build
failure where we missed a code site or where a crossing commit itroduces
new irq_desc[] usage. )
v2: according to Eric, change get_irq_desc() to irq_desc()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to avoid merge problems further down the line add placeholders
for several of the WM8350 client devices and register them, otherwise
the patches adding the client devices will all try to update the same
code.
Also remove redundant checks for null regulator platform devices while
we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
