This PFSM controls the operational modes of the PMIC:
- STANDBY and LP_STANDBY,
- ACTIVE state,
- MCU_ONLY state,
- RETENTION state, with or without DDR and/or GPIO retention.
Depending on the current operational mode, some voltage domains
remain energized while others can be off.
This PFSM is also used to trigger a firmware update, and provides
R/W access to device registers.
See Documentation/misc-devices/tps6594-pfsm.rst for more
information.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-5-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for TPS6594 ESM (Error Signal Monitor).
This device monitors the SoC error output signal at its nERR_SOC input pin.
In error condition, ESM toggles its nRSTOUT_SOC pin to reset the SoC.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-4-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of driver changes for char/misc drivers and other
smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem seems
under very active development recently. This required also merging
in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/inQw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksvwCeOvU//SPwrbIpaeHAmHUv0PSVOrwAoKmt4ICh
hQUudlztfkvUJxKIH0gh
=Sjk4
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
Now that we have a subsystem for compute accelerators, move the
habanalabs driver to it.
This patch only moves the files and fixes the Makefiles. Future
patches will change the existing code to register to the accel
subsystem and expose the accel device char files instead of the
habanalabs device char files.
Update the MAINTAINERS file to reflect this change.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The Triple Modular Redundancy(TMR) provides functional fault injection by
changing selected MicroBlaze instructions, which provides the possibility
to verify that the TMR subsystem error detection and fault recovery logic
is working properly.
Usage:
echo 1 > /sys/kernel/debug/xtmr_inject/inject_fault/inject_fault
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.kedareswara.rao@amd.com>
Link: https://lore.kernel.org/r/20221125054113.122833-5-appana.durga.kedareswara.rao@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Triple Modular Redundancy(TMR) subsystem contains three microblaze cores,
subsystem is fault-tolerant and continues to operate nominally after
encountering an error. Together with the capability to detect and recover
from errors, the implementation ensures the reliability of the entire
subsystem. TMR Manager is responsible for performing recovery of the
subsystem detects the fault via a break signal it invokes microblaze
software break handler which calls the tmr manager driver api to
update the error count and status, added support for fault detection
feature via sysfs interface.
Usage:
To know the break handler count(Error count):
cat /sys/devices/platform/amba_pl/44a10000.tmr_manager/errcnt
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.kedareswara.rao@amd.com>
Link: https://lore.kernel.org/r/20221125054113.122833-3-appana.durga.kedareswara.rao@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver support for accessing various information reported by
Ampere's SMpro co-processor such as Boot Progress and other
miscellaneous data.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20221031024442.2490881-4-quan@os.amperecomputing.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Ampere's SMpro error monitor driver for monitoring and reporting
RAS-related errors as reported by SMpro co-processor found on Ampere's
Altra processor family.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20221031024442.2490881-3-quan@os.amperecomputing.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. PIO function is one of the functions in the
multi-function endpoint. PIO function combines a GPIO controller and also
an interface to program pci1xxxx's OTP & EEPROM. This auxiliary bus driver
is loaded for the PIO function and separate child devices are enumerated
for GPIO controller and OTP/EEPROM interface.
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220824200047.150308-2-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver creates per-cpu hrtimers which are required to do the
periodic 'pet' operation. On a conventional watchdog-core driver, the
userspace is responsible for delivering the 'pet' events by writing to
the particular /dev/watchdogN node. In this case we require a strong
thread affinity to be able to account for lost time on a per vCPU.
This part of the driver is the 'frontend' which is reponsible for
delivering the periodic 'pet' events, configuring the virtual peripheral
and listening for cpu hotplug events. The other part of the driver is
an emulated MMIO device which is part of the KVM virtual machine
monitor and this part accounts for lost time by looking at the
/proc/{}/task/{}/stat entries.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Will Deacon <will@kernel.org>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://lore.kernel.org/r/20220711081720.2870509-3-sebastianene@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Open Profile for DICE is an open protocol for measured boot compatible
with the Trusted Computing Group's Device Identifier Composition
Engine (DICE) specification. The generated Compound Device Identifier
(CDI) certificates represent the hardware/software combination measured
by DICE, and can be used for remote attestation and sealing.
Add a driver that exposes reserved memory regions populated by firmware
with DICE CDIs and exposes them to userspace via a character device.
Userspace obtains the memory region's size from read() and calls mmap()
to create a mapping of the memory region in its address space. The
mapping is not allowed to be write+shared, giving userspace a guarantee
that the data were not overwritten by another process.
Userspace can also call write(), which triggers a wipe of the DICE data
by the driver. Because both the kernel and userspace mappings use
write-combine semantics, all clients observe the memory as zeroed after
the syscall has returned.
Cc: Andrew Scull <ascull@google.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20220126231237.529308-3-dbrazdil@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had been
maintained out-of-tree by Larry with the end goal of actually being able
to get this driver out of staging eventually. Despite that driver being
"newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to see,
that is why there are additions to the mfc and misc driver subsystems.
All of these were acked by the various subsystem maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+BKg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yku5gCgyMykJ2mwtEiQxfAWu13e2iZX29AAnjk38ANp
Un2sQXYnL9RVlcnjLg+X
=jMWL
-----END PGP SIGNATURE-----
Merge tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO and staging driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had
been maintained out-of-tree by Larry with the end goal of actually
being able to get this driver out of staging eventually. Despite that
driver being "newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to
see, that is why there are additions to the mfc and misc driver
subsystems. All of these were acked by the various subsystem
maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems"
[ Note: the r8188eu merge clashed with commit 89939e8906 ("staging:
rtlwifi: use siocdevprivate") from the networking tree. When resolving
the issue, I noted that the whole r8188eu rtw_android code is dead
since commit ae7471cae0 ("staging: r8188eu: remove rtw_ioctl
function").
End result: the merge resolution was to throw all of that away,
rather than do the mindless fixup to code that isn't actually
reachable - Linus ]
* tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (551 commits)
staging: vt6655: Remove filenames in files
staging: r8188eu: add extra TODO entries
staging: vt6656: Remove filenames in files
staging: wlan-ng: fix invalid assignment warning
staging: r8188eu: rename fields of struct rtl_ps
staging: r8188eu: remove ODM_DynamicPrimaryCCA_DupRTS()
staging: r8188eu: rename fields of struct dyn_primary_cca
staging: r8188eu: rename struct field Wifi_Error_Status
staging: r8188eu: Provide a TODO file for this driver
staging: r8188eu: remove unneeded variable
staging: r8188eu: remove unneeded conversions to bool
staging: r8188eu: remove {read,write}_macreg
staging: r8188eu: core: remove condition with no effect
staging: r8188eu: remove ethernet.h header file
staging: r8188eu: remove ip.h header file
staging: r8188eu: remove if_ether.h header file
staging: r8188eu: make rtw_deinit_intf_priv return void
staging: r8188eu: use is_multicast_ether_addr in os_dep/recv_linux.c
staging: r8188eu: use is_multicast_ether_addr in hal/rtl8188eu_xmit.c
staging: r8188eu: use is_multicast_ether_addr in core/rtw_xmit.c
...
General Electric Healthcare's PPD has a secondary processor from
NXP's Kinetis K20 series. That device has two SPI chip selects:
The main interface's behaviour depends on the loaded firmware
and is currently unused.
The secondary interface can be used to update the firmware using
EzPort protocol. This is implemented by this driver using the
kernel's firmware API. The firmware is being flashed into
non-volatile flash memory, so it is enough to flash it once
and not on every boot. Flashing will wear the flash memory
(it has a life time of at least 10k programming cycles). At
the same time only occasional FW updates are expected (like e.g.
a BIOS update). Thus the firmware update is triggered via sysfs
instead of doing it in the driver's probe routine like many
other drivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-4-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split-up generic and platform dependent code in order to be able to re-use
generic event handling code in pvpanic PCI device driver in the next patches.
The code from pvpanic.c was split in two new files:
- pvpanic.c: generic code that handles pvpanic events
- pvpanic-mmio.c: platform/bus dependent code
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Link: https://lore.kernel.org/r/1616597356-20696-2-git-send-email-mihai.carabas@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210122114358.39299-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initial version of Broadcom VK driver to enumerate PCI device IDs
of Valkyrie and Viper device IDs.
VK based cards provide real-time high performance, high throughput,
low latency offload compute engine operations.
They are used for multiple parallel offload tasks as:
audio, video and image processing and crypto operations.
Further commits add additional features to driver beyond probe/remove.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-3-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HiKey960 has a fairly complex USB configuration due to it
needing to support a USB-C port for host/device mode and multiple
USB-A ports in host mode, all using a single USB controller.
See schematics here:
https://github.com/96boards/documentation/raw/master/consumer/hikey/hikey960/hardware-docs/HiKey960_Schematics.pdf
This driver acts as a usb-role-switch intermediary, intercepting
the role switch notifications from the tcpm code, and passing
them on to the dwc3 core.
In doing so, it also controls the onboard hub and power gpios in
order to properly route the data lines between the USB-C port
and the onboard hub to the USB-A ports.
Signed-off-by: Yu Chen <chenyu56@huawei.com>
[jstultz: Major rework to make the driver a usb-role-switch
intermediary]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/c263f72e1d803c18c45a69ce2c333e79a7ed89ff.1599717402.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only thing that vexpress-syscfg does is provide a regmap to
vexpress-config bus child devices. There's little reason to have 2
components for this. The current structure with initcall ordering
requirements makes turning these components into modules more difficult.
So let's start to simplify things and merge vexpress-syscfg into
vexpress-config. There's no functional change in this commit and it's
still separate components until subsequent commits.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Uacce (Unified/User-space-access-intended Accelerator Framework) targets to
provide Shared Virtual Addressing (SVA) between accelerators and processes.
So accelerator can access any data structure of the main cpu.
This differs from the data sharing between cpu and io device, which share
only data content rather than address.
Since unified address, hardware and user space of process can share the
same virtual address in the communication.
Uacce create a chrdev for every registration, the queue is allocated to
the process when the chrdev is opened. Then the process can access the
hardware resource by interact with the queue file. By mmap the queue
file space to user space, the process can directly put requests to the
hardware without syscall to the kernel space.
The IOMMU core only tracks mm<->device bonds at the moment, because it
only needs to handle IOTLB invalidation and PASID table entries. However
uacce needs a finer granularity since multiple queues from the same
device can be bound to an mm. When the mm exits, all bound queues must
be stopped so that the IOMMU can safely clear the PASID table entry and
reallocate the PASID.
An intermediate struct uacce_mm links uacce devices and queues.
Note that an mm may be bound to multiple devices but an uacce_mm
structure only ever belongs to a single device, because we don't need
anything more complex (if multiple devices are bound to one mm, then
we'll create one uacce_mm for each bond).
uacce_device --+-- uacce_mm --+-- uacce_queue
| '-- uacce_queue
|
'-- uacce_mm --+-- uacce_queue
+-- uacce_queue
'-- uacce_queue
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Kenneth Lee <liguozhu@hisilicon.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIT1g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym9lwCgrHZlMMvfYNVm6GQ5ge58JJsVTL4AoNatTcL4
hfVMA6pCHWBjV65xVSf6
=Tijw
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
habanalabs: correctly cast variable to __le32
habanalabs: show correct id in error print
habanalabs: stop using the acronym KMD
habanalabs: display card name as sensors header
habanalabs: add uapi to retrieve aggregate H/W events
habanalabs: add uapi to retrieve device utilization
habanalabs: Make the Coresight timestamp perpetual
habanalabs: explicitly set the queue-id enumerated numbers
habanalabs: print to kernel log when reset is finished
habanalabs: replace __le32_to_cpu with le32_to_cpu
habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
habanalabs: Handle HW_IP_INFO if device disabled or in reset
habanalabs: Expose devices after initialization is done
habanalabs: improve security in Debug IOCTL
habanalabs: use default structure for user input in Debug IOCTL
habanalabs: Add descriptive name to PSOC app status register
habanalabs: Add descriptive names to PSOC scratch-pad registers
habanalabs: create two char devices per ASIC
habanalabs: change device_setup_cdev() to be more generic
...
The IOC4 is a multi-function chip seen on SGI SN2 and some SGI MIPS
systems. This removes the base driver, which while not having an SN2
Kconfig dependency was only for sub-drivers that had one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-15-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
This driver has been marked broken since 2013, see commit 98097858cc
("misc: mark spear13xx-pcie-gadget as broken"). Let's remove this file
now that it's been more than 5 years of existing in a broken state.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/5d41a2b7.1c69fb81.c8d56.edb6@mx.google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FSA9480 has a new driver more appropriately located
in the drivers/extcon subsystem. It is also more complete
and includes device tree support. Delete the old misc
driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Pawe Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20190630140302.16245-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a platform driver that matches with xlnx,
sd-fec-1.1 device tree node and registers as a character
device, including:
- SD-FEC driver binds to sdfec DT node.
- creates and initialise an initial driver dev structure.
- add the driver in Linux build and Kconfig.
Tested-by: Dragan Cvetic <dragan.cvetic@xilinx.com>
Signed-off-by: Derek Kiernan <derek.kiernan@xilinx.com>
Signed-off-by: Dragan Cvetic <dragan.cvetic@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a SoC folder for the ASPEED parts and place the misc drivers
currently present into this folder. These drivers are not generic part
drivers, but rather only apply to the ASPEED SoCs.
Signed-off-by: Patrick Venture <venture@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the habanalabs skeleton driver. The driver does nothing at
this stage except very basic operations. It contains the minimal code to
insmod and rmmod the driver and to create a /dev/hlX file per PCI device.
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic driver model for Qualcomm FastRPC driver which
implements an IPC (Inter-Processor Communication) mechanism that
allows for clients to transparently make remote method invocations
across processor boundaries.
Each DSP rpmsg channel is represented as fastrpc channel context and
is exposed as a character device for userspace interface.
Each compute context bank is represented as fastrpc-session-context,
which are dynamically managed by the channel context char device.
Co-developed-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
This driver provides support for Alcor Micro AU6601 and AU6621
card readers.
This is single LUN HW and it is expected to work with following standards:
- Support SDR104 / SDR50
- MultiMedia Card (MMC)
- Memory Stick (MS)
- Memory Stick PRO (MS_Pro)
Since it is a PCIe controller, it should work on any architecture
supporting PCIe. For now, it was developed and tested only on x86_64.
This driver is a result of RE work and was created without any
documentation or real knowledge of HW internals.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move pvpanic.c from drivers/platform/x86 to drivers/misc.
Following patches will use pvpanic device in arm64.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a logical device which provides an
interface between the hypervisor and a management
partition. This interface is like a message
passing interface. This management partition
is intended to provide an alternative to HMC-based
system management.
VMC enables the Management LPAR to provide basic
logical partition functions:
- Logical Partition Configuration
- Boot, start, and stop actions for individual
partitions
- Display of partition status
- Management of virtual Ethernet
- Management of virtual Storage
- Basic system management
This driver is to be used for the POWER Virtual
Management Channel Virtual Adapter on the PowerPC
platform. It provides a character device which
allows for both request/response and async message
support through the /dev/ibmvmc node.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Reviewed-by: Adam Reznechek <adreznec@linux.vnet.ibm.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Taylor Jakobson <tjakobs@us.ibm.com>
Tested-by: Brad Warrum <bwarrum@us.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LKDTM modules keep expanding, and it's getting weird to have each file
get a prefix. Instead, move to a subdirectory for cleaner handling.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
OCXL_BASE triggers the platform support needed by the driver.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
The Texas Instruments DAC7512 has the exact same pinout, programming
interface and power-down modes as the Texas Instruments DAC121S101 and
Analog Devices AD5320, which are already supported by the IIO driver
ad5446.c. Remove the duplicate misc driver.
This requires user space to migrate to the standardized IIO sysfs ABI.
(In other words, it needs to change a filename.)
The IIO driver supports the chip's features more fully, e.g. the ability
to power down the output or choose one of the available powerdown modes.
There is an oddity with the misc driver in that it initializes the SPI
slave to SPI_MODE_0, in contradiction to the datasheet which specifies
that data is latched in on the falling edge, implying that SPI_MODE_1
or SPI_MODE_2 must be used. Another oddity is that Kconfig and the
MODULE_DESCRIPTION() claim the chip has 16-bit resolution although it
actually has 12-bit.
Datasheets:
http://www.ti.com/lit/ds/symlink/dac7512.pdfhttp://www.ti.com/lit/ds/symlink/dac121s101.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5320.pdf
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The existing REFCOUNT_* LKDTM tests were designed only for testing a narrow
portion of CONFIG_REFCOUNT_FULL. This moves the tests to their own file and
expands their testing to poke each boundary condition.
Since the protections (CONFIG_REFCOUNT_FULL and x86-fast) use different
saturation values and reach-zero behavior, those have to be build-time
set so the tests can actually validate things are happening at the
right places.
Notably, the x86-fast protection will fail REFCOUNT_INC_ZERO and
REFCOUNT_ADD_ZERO since those conditions are not checked (only overflow
is critical to protecting refcount_t). CONFIG_REFCOUNT_FULL will warn for
each REFCOUNT_*_NEGATIVE test since it provides zero-pinning behaviors
(which allows it to pass REFCOUNT_INC_ZERO and REFCOUNT_ADD_ZERO).
Signed-off-by: Kees Cook <keescook@chromium.org>
This driver enables the LPC snoop hardware on the ASPEED BMC
which generates an interrupt upon every write to an I/O port
by the host.
This is typically used to monitor BIOS boot progress by listening
to well-known debug port 80h.
The functionality in this commit just saves all snooped values
to a circular 2K buffer in the kernel, subsequent commits can
act on the values to do things with them.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
Add PCI endpoint test driver that can verify base address register, legacy
interrupt/MSI interrupt and read/write/copy buffers between host and
device. The corresponding pci-epf-test function driver should be used on
the EP side.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
I ran into a link error on ARM64 for lkdtm_rodata_do_nothing:
drivers/misc/built-in.o: In function `lkdtm_rodata_do_nothing':
:(.rodata+0x68c8): relocation truncated to fit: R_AARCH64_CALL26 against symbol `__sanitizer_cov_trace_pc' defined in .text section in kernel/built-in.o
I did not analyze this further, but my theory is that we would need a trampoline
to call __sanitizer_cov_trace_pc(), but the linker (correctly) only adds trampolines
for callers in executable sections.
Disabling KCOV for this one file avoids the build failure with no
other practical downsides I can think of.
The problem can only happen on kernels that contain both kcov and
lkdtm, so if we want to backport this, it should be in the earliest
version that has both (v4.8).
Fixes: 5c9a8750a6 ("kernel: add kcov code coverage")
Fixes: 9a49a528dc ("lkdtm: add function for testing .rodata section")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like arm-charlcd.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like panel.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
