When stalling EP0, we need to wait for an ACK interrupt,
otherwise we may get out of sync on the next setup packet
data phase. Also we need to ignore the direction when
processing that interrupt as the HW reports a potential
mismatch.
Implement this by adding a stall state to EP0. This fixes
some reported issues with mass storage and some hosts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Otherwise, we can have a stale state after a disconnect and reconnect
causing errors on the first SETUP packet to the device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This bit should be only set when the port enable goes down, for
example, on errors. Not when it gets set after a port reset. Some
USB stacks seem to be sensitive to this and fails enumeration.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use clk_bulk_prepare_enable() and clk_bulk_disable_unprepare() to
simplify code a bit. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devres to get clocks and drop explicit clock freeing. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08f871a3ac ("usb: dwc3: host: convey the PHYs to xhci") added
forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat
device. However XHCI(-plat) driver never gained support for generic PHYs,
thus the lookup added by that commit is never used. In meantime the commit
d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
incorrectly changed the device used for creating lookup, making the lookup
useless and generic PHYs inaccessible from XHCI device.
However since commit 178a0bce05 ("usb: core: hcd: integrate the PHY
wrapper into the HCD core") USB HCD already handles generic PHYs acquired
from the HCD's 'sysdev', which in this case is DWC3 core device. This means
that creating any custom lookup entries for XHCI driver is no longer needed
and can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It has been requested that usbfs should implement runtime power
management, instead of forcing the device to remain at full power as
long as the device file is open. This patch introduces that new
feature.
It does so by adding three new usbfs ioctls:
USBDEVFS_FORBID_SUSPEND: Prevents the device from going into
runtime suspend (and causes a resume if the device is already
suspended).
USBDEVFS_ALLOW_SUSPEND: Allows the device to go into runtime
suspend. Some time may elapse before the device actually is
suspended, depending on things like the autosuspend delay.
USBDEVFS_WAIT_FOR_RESUME: Blocks until the call is interrupted
by a signal or at least one runtime resume has occurred since
the most recent ALLOW_SUSPEND ioctl call (which may mean
immediately, even if the device is currently suspended). In
the latter case, the device is prevented from suspending again
just as if FORBID_SUSPEND was called before the ioctl returns.
For backward compatibility, when the device file is first opened
runtime suspends are forbidden. The userspace program can then allow
suspends whenever it wants, and either resume the device directly (by
forbidding suspends again) or wait for a resume from some other source
(such as a remote wakeup). URBs submitted to a suspended device will
fail or will complete with an appropriate error code.
This combination of ioctls is sufficient for user programs to have
nearly the same degree of control over a device's runtime power
behavior as kernel drivers do.
Still lacking is documentation for the new ioctls. I intend to add it
later, after the existing documentation for the usbfs userspace API is
straightened out into a reasonable form.
Suggested-by: Mayuresh Kulkarni <mkulkarni@opensource.cirrus.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908071013220.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Link: https://lore.kernel.org/r/20190806144502.17792-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Cc: Ding Xiang <dingxiang@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20190806144502.17792-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Link: https://lore.kernel.org/r/20190806144502.17792-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Link: https://lore.kernel.org/r/20190806144502.17792-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://lore.kernel.org/r/20190806144502.17792-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Cc: Pete Zaitcev <zaitcev@redhat.com>
Link: https://lore.kernel.org/r/20190806144502.17792-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Cc: Guido Kiener <guido.kiener@rohde-schwarz.com>
Cc: Steve Bayless <steve_bayless@keysight.com>
Link: https://lore.kernel.org/r/20190806144502.17792-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Link: https://lore.kernel.org/r/20190806144502.17792-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Link: https://lore.kernel.org/r/20190806144502.17792-8-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB drivers now support the ability for the driver core to handle the
creation and removal of device-specific sysfs files in a race-free
manner. Take advantage of that by converting the driver to use this by
moving the sysfs attributes into a group and assigning the dev_groups
pointer to it.
Link: https://lore.kernel.org/r/20190806144502.17792-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Peter Chen <Peter.Chen@nxp.com>
Link: https://lore.kernel.org/r/20190805193636.25560-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20190805193636.25560-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20190805193636.25560-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20190806073235.25140-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805191426.GA12414@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190805184842.GA8627@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When a gadget is disabled, kill_all_requests() can be called
simultaneously from both a user process via dwc2_hsotg_pullup() and from
the interrupt handler if the hardware detects disconnection.
Since we drop the lock in dwc2_hsotg_complete_request() in order to call
the completion handler, this means that the list is modified
concurrently and leads to an infinite loop in kill_all_requests().
Replace the foreach loop with a while-not-empty loop in order to remove
the danger of this concurrent modification.
Note: I observed this with threadirqs, I'm not sure if it can be
triggered without threaded interrupts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently, the authorized_default and interface_authorized_default
attributes for HCD are set up after the uevent has been sent to userland.
This creates a race condition where userland may fail to access this
file when processing the event. Move the appending of these attributes
earlier relying on the usb_bus_notify dispatcher.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190806110050.38918-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have to drop the mutex before we close() upon disconnect()
as close() needs the lock. This is safe to do by dropping the
mutex as intfdata is already set to NULL, so open() will fail.
Fixes: 03f36e885f ("USB: open disconnect race in iowarrior")
Reported-by: syzbot+a64a382964bf6c71a9c0@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20190808092728.23417-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core now supports the option to automatically create and
remove any needed sysfs attribute files for a driver when the device is
bound/removed from it. Convert the uscsi_ccg code to use that instead
of trying to create sysfs files "by hand".
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190805193636.25560-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Acked-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20190805193636.25560-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UWB and wusbcore code is long obsolete, so let us just move the code
out of the real part of the kernel and into the drivers/staging/
location with plans to remove it entirely in a few releases.
Link: https://lore.kernel.org/r/20190806101509.GA11280@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_device_driver to make it easier for USB
drivers to also use it.
Yes, users of usb_device_driver are much rare, but there are instances
already that use custom sysfs files, so adding this support will make
things easier for those drivers. usbip is one example, hubs might be
another one.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core supports dev_groups for individual drivers,
expose that pointer to struct usb_driver to make it easier for USB
drivers to also use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190806144502.17792-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190805193636.25560-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon an error within proc_do_submiturb(), dec_usb_memory_use_count()
gets called once by the error handling tail and again by free_async().
Remove the first call.
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190804235044.22327-1-gavinli@thegavinli.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QCA Rome USB Bluetooth controller has several issues once LPM gets
enabled:
- Fails to get enumerated in coldboot. [1]
- Drains more power (~ 0.2W) when the system is in S5. [2]
- Disappears after a warmboot. [2]
The issue happens because the device lingers at LPM L1 in S5, so device
can't get enumerated even after a reboot.
Disable LPM at shutdown to solve the issue.
[1] https://bugs.launchpad.net/bugs/1757218
[2] https://patchwork.kernel.org/patch/10607097/
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190805142412.23965-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190802130408.20336-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM may receive PD messages associated with unknown or unsupported
alternate modes. If that happens, calls to typec_match_altmode()
will return NULL. The tcpm code does not currently take this into
account. This results in crashes.
Unable to handle kernel NULL pointer dereference at virtual address 000001f0
pgd = 41dad9a1
[000001f0] *pgd=00000000
Internal error: Oops: 5 [#1] THUMB2
Modules linked in: tcpci tcpm
CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6
Hardware name: Atmel SAMA5
Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm]
PC is at typec_altmode_attention+0x0/0x14
LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]
...
[<c03fbee8>] (typec_altmode_attention) from [<bf8030fb>]
(tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm])
[<bf8030fb>] (tcpm_pd_rx_handler [tcpm]) from [<c012082b>]
(process_one_work+0x123/0x2a8)
[<c012082b>] (process_one_work) from [<c0120a6d>]
(worker_thread+0xbd/0x3b0)
[<c0120a6d>] (worker_thread) from [<c012431f>] (kthread+0xcf/0xf4)
[<c012431f>] (kthread) from [<c01010f9>] (ret_from_fork+0x11/0x38)
Ignore PD messages if the associated alternate mode is not supported.
Fixes: e9576fe8e6 ("usb: typec: tcpm: Support for Alternate Modes")
Cc: stable <stable@vger.kernel.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1564761822-13984-1-git-send-email-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core will reset the default control endpoint "ep0" before resetting
a device. if the endpoint has a valid pointer back to the usb device
then the xhci driver reset callback will try to clear the toggle for
the endpoint.
ep0 didn't use to have this pointer set as ep0 was always allocated
by default together with a xhci slot for the usb device. Other endpoints
got their usb device pointer set in xhci_add_endpoint()
This changed with commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
which sets the pointer for any endpoint on a FS/LS device behind a
HS hub that halts, including ep0.
If xHC controller needs to be reset at resume, then all the xhci slots
will be lost. Slots will be reenabled and reallocated at device reset,
but unlike other endpoints the ep0 is reset before device reset, while
the xhci slot may still be invalid, causing NULL pointer dereference.
Fix it by checking that the endpoint has both a usb device pointer and
valid xhci slot before trying to clear the toggle.
This issue was not seen earlier as ep0 didn't use to have a valid usb
device pointer, and other endpoints were only reset after device reset
when xhci slots were properly reenabled.
Reported-by: Bob Gleitsmann <rjgleits@bellsouth.net>
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/1564758044-24748-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():
xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
Fixes: 435cc1138e ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the past, USB PHY handling has been moved in the HCD core. Some
host controller drivers needing more control of the PHYs, they have
been granted the freedom to handle themselves the PHY states and to
prevent the HCD core to do so in commit 4e88d4c083 ("usb: add a flag
to skip PHY initialization to struct usb_hcd"). With this change, any
USB host controller could set the hcd->skip_phy_initialization flag so
that the HCD core would just skip the PHY initialization sequence.
However, in the USB subsystem, there are currently two entirely
different forms of PHY: one is called 'usb_phy' and is
USB-subsystem-wide, while there is also the generic and kernel-wide
'phy' from the (recent) generic PHY framework.
When the commit above was introduced, both type of PHYs where handled
by the HCD core.
Later, commit bc40f53417 ("USB: core: hcd: drop support for legacy
phys") removed the support for the former type of PHYs in the HCD
core. These 'usb_phy' are still present though, but managed from the
controller drivers only. Hence, setting the
hcd->skip_phy_initialization flag just because a 'usb_phy' is
initialized by a controller driver is a non-sense.
For instance on Armada CP110, a 'usb_phy' is there to enable the power
supply to the USB host, while there is also a COMPHY block providing
SERDES lanes configuration that is referenced as a PHY from the common
PHY framework.
Right now, users of the xhci-plat.c driver either use a 'usb_phy' only
and do not care about the attempt of generic PHY initialization within
the HCD core (as there is none); or they use a single 'phy' and the
code flow does not pass through the block setting
hcd->skip_phy_initialization anyway.
While there is not users of both PHY types at the same time, drop this
limitation from the xhci-plat.c driver. Note that the tegra driver
probably has the same limitation and could definitely benefit from a
similar change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20190731121150.2253-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190731223917.16532-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to match a device by its type and provide wrappers
for {bus/class/driver}_find_device() APIs.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-usb@vger.kernel.org
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20190723221838.12024-5-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to match the firmware node handle of a device and provide
wrappers for {bus/class/driver}_find_device() APIs to avoid proliferation
of duplicate custom match functions.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-usb@vger.kernel.org
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Joe Perches <joe@perches.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190723221838.12024-4-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to match the device name for device lookup. Also
reuse this generic exported helper for the existing bus_find_device_by_name().
and add similar variants for driver/class.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-leds@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wpan@vger.kernel.org
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20190723221838.12024-2-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/usb/phy/phy-ab8500-usb.c: In function 'ab8500_usb_link_status_update':
drivers/usb/phy/phy-ab8500-usb.c:424:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDB;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:425:2: note: here
case USB_LINK_NOT_CONFIGURED_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:440:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDC;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:441:2: note: here
case USB_LINK_STD_HOST_NC_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:459:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDA;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:460:2: note: here
case USB_LINK_HM_IDGND_8500:
^~~~
drivers/usb/phy/phy-ab8500-usb.c: In function 'ab8505_usb_link_status_update':
drivers/usb/phy/phy-ab8500-usb.c:332:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDB;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:333:2: note: here
case USB_LINK_NOT_CONFIGURED_8505:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:352:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDC;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:353:2: note: here
case USB_LINK_STD_HOST_NC_8505:
^~~~
drivers/usb/phy/phy-ab8500-usb.c:370:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
event = UX500_MUSB_RIDA;
~~~~~~^~~~~~~~~~~~~~~~~
drivers/usb/phy/phy-ab8500-usb.c:371:2: note: here
case USB_LINK_HM_IDGND_8505:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20190729000631.GA24165@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/usb/host/ohci-tmio.c: In function ‘tmio_stop_hc’:
./include/linux/device.h:1499:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/ohci-tmio.c:99:4: note: in expansion of macro ‘dev_err’
dev_err(&dev->dev, "Unsupported amount of ports: %d\n", ohci->num_ports);
^~~~~~~
In file included from drivers/usb/host/ohci-hcd.c:1257:0:
drivers/usb/host/ohci-tmio.c💯3: note: here
case 3:
^~~~
drivers/usb/host/ohci-tmio.c:101:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW3;
^
drivers/usb/host/ohci-tmio.c:102:3: note: here
case 2:
^~~~
drivers/usb/host/ohci-tmio.c:103:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
pm |= CCR_PM_USBPW2;
^
drivers/usb/host/ohci-tmio.c:104:3: note: here
case 1:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190729222201.GA19408@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the code for getting generic PHYs from standard device tree array
from the main controller device node. This is a first step in resolving
the conflict between Exynos EHCI/OHCI sub-nodes and generic USB device
bindings. Later the sub-nodes currently used for assigning PHYs to root
ports of the controller will be removed making a place for the generic
USB device bindings nodes.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190726081453.9456-3-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If config tcpm as module, module unload will not remove tcpm dir,
then the next module load will have problem: the rootdir is NULL
but tcpm dir is still there, so tcpm_debugfs_init() will create
tcpm dir again with failure, fix it by remove the tcpm dir if no
children.
Cc: stable@vger.kernel.org # v4.15+
Fixes: 4b4e02c831 ("typec: tcpm: Move out of staging")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190717080646.30421-2-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A second regression was found in the immediate data transfer (IDT)
support which was added to 5.2 kernel
IDT is used to transfer small amounts of data (up to 8 bytes) in the
field normally used for data dma address, thus avoiding dma mapping.
If the data was not already dma mapped, then IDT support assumed data was
in urb->transfer_buffer, and did not take into accound that even
small amounts of data (8 bytes) can be in a scatterlist instead.
This caused a NULL pointer dereference when sg_dma_len() was used
with non-dma mapped data.
Solve this by not using IDT if scatter gather buffer list is used.
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Cc: <stable@vger.kernel.org> # v5.2
Reported-by: Maik Stohn <maik.stohn@seal-one.com>
Tested-by: Maik Stohn <maik.stohn@seal-one.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1564044861-1445-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a partial revert of 73d31def1a "usb: usb251xb: Create a ports
field collector method", which broke a existing devicetree
(arch/arm64/boot/dts/freescale/imx8mq.dtsi).
There is no reason why the swap-dx-lanes property should not apply to
the upstream port. The reason given in the breaking commit was that it's
inconsitent with respect to other port properties, but in fact it is not.
All other properties which only apply to the downstream ports explicitly
reject port 0, so there is pretty strong precedence that the driver
referred to the upstream port as port 0. So there is no inconsistency in
this property at all, other than the swapping being also applicable to
the upstream port.
CC: stable@vger.kernel.org #5.2
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190719084407.28041-3-l.stach@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable retval is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed. Also remove a blank
line.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190704150341.759-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do extra cpu_to_le32 conversion for
put_unaligned_le32 because it is already implemented
in this function.
Fixes sparse error:
xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types)
xhci-hub.c:1152:44: expected unsigned int [usertype] val
xhci-hub.c:1152:44: got restricted __le32 [usertype]
Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status"
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032010.7258-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header, oxu210hp.h is only included from oxu210hp-hcd.c
so squash it.
When I moved the code, I also fixed the following warnings from
scripts/checkpatch.pl:
drivers/usb/host/oxu210hp-hcd.c:117: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:196: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:221: warning: __packed is preferred over __attribute__((packed))
drivers/usb/host/oxu210hp-hcd.c:266: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:336: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:354: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:385: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:393: warning: __aligned(size) is preferred over __attribute__((aligned(size)))
drivers/usb/host/oxu210hp-hcd.c:429: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:432: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:436: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:451: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:461: warning: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/usb/host/oxu210hp-hcd.c:467: warning: please, no space before tabs
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721144909.5295-2-yamada.masahiro@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct oxu210hp_platform_data is defined, but not used at all.
$ git grep oxu210hp_platform_data
include/linux/oxu210hp.h:struct oxu210hp_platform_data {
include/linux/oxu210hp.h exists just for defining an unused structure,
so it can go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721144909.5295-1-yamada.masahiro@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use use fwnode_property_count_uXX() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190723193750.69038-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20190723191639.67883-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131838.1931-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzboot reported that
https://syzkaller.appspot.com/bug?extid=fd2bd7df88c606eea4ef
There is not consitency parameter in cluste_id_get/put calling.
In case of getting the id with result is failure, the wusbhc->cluster_id
will not be updated and this can not be used for wusb_cluster_id_put().
Tested report
https://groups.google.com/d/msg/syzkaller-bugs/0znZopp3-9k/oxOrhLkLEgAJ
Reproduce and gdb got the details:
139 addr = wusb_cluster_id_get();
(gdb) n
140 if (addr == 0)
(gdb) print addr
$1 = 254 '\376'
(gdb) n
142 result = __hwahc_set_cluster_id(hwahc, addr);
(gdb) print result
$2 = -71
(gdb) break wusb_cluster_id_put
Breakpoint 3 at 0xffffffff836e3f20: file drivers/usb/wusbcore/wusbhc.c, line 384.
(gdb) s
Thread 2 hit Breakpoint 3, wusb_cluster_id_put (id=0 '\000') at drivers/usb/wusbcore/wusbhc.c:384
384 id = 0xff - id;
(gdb) n
385 BUG_ON(id >= CLUSTER_IDS);
(gdb) print id
$3 = 255 '\377'
Reported-by: syzbot+fd2bd7df88c606eea4ef@syzkaller.appspotmail.com
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190724020601.15257-1-tranmanphong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_memremap() function doesn't return NULL, it returns error
pointers.
Fixes: b0310c2f09 ("USB: use genalloc for USB HCs with local memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20190607135709.GC16718@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the following error happens on
swiotlb environment:
xhci-hcd ee000000.usb: swiotlb buffer is full (sz: 524288 bytes), total 32768 (slots), used 1338 (slots)
On the kernel v5.1, block settings of a usb-storage with SuperSpeed
were the following so that the block layer will allocate buffers
up to 64 KiB, and then the issue didn't happen.
max_segment_size = 65536
max_hw_sectors_kb = 1024
After the commit 09324d32d2 ("block: force an unlimited segment
size on queues with a virt boundary") is applied, the block settings
are the following. So, the block layer will allocate buffers up to
1024 KiB, and then the issue happens:
max_segment_size = 4294967295
max_hw_sectors_kb = 1024
To fix the issue, the usb-storage driver checks the maximum size of
a mapping for the device and then adjusts the max_hw_sectors_kb
if required. After this patch is applied, the block settings will
be the following, and then the issue doesn't happen.
max_segment_size = 4294967295
max_hw_sectors_kb = 256
Fixes: 09324d32d2 ("block: force an unlimited segment size on queues with a virt boundary")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/1563793105-20597-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_amd_find_chipset_info() is used for chipset detection for
several quirks. It is strange that its return value indicates
the need for the PLL quirk, which means it is often ignored.
This patch adds a function specifically for checking the PLL
quirk like the other ones. Additionally, rename probe_result to
something more appropriate.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-3-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull vfs mount updates from Al Viro:
"The first part of mount updates.
Convert filesystems to use the new mount API"
* 'work.mount0' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
mnt_init(): call shmem_init() unconditionally
constify ksys_mount() string arguments
don't bother with registering rootfs
init_rootfs(): don't bother with init_ramfs_fs()
vfs: Convert smackfs to use the new mount API
vfs: Convert selinuxfs to use the new mount API
vfs: Convert securityfs to use the new mount API
vfs: Convert apparmorfs to use the new mount API
vfs: Convert openpromfs to use the new mount API
vfs: Convert xenfs to use the new mount API
vfs: Convert gadgetfs to use the new mount API
vfs: Convert oprofilefs to use the new mount API
vfs: Convert ibmasmfs to use the new mount API
vfs: Convert qib_fs/ipathfs to use the new mount API
vfs: Convert efivarfs to use the new mount API
vfs: Convert configfs to use the new mount API
vfs: Convert binfmt_misc to use the new mount API
convenience helper: get_tree_single()
convenience helper get_tree_nodev()
vfs: Kill sget_userns()
...
Pull i2c updates from Wolfram Sang:
"New stuff from the I2C world:
- in the core, getting irqs from ACPI is now similar to OF
- new driver for MediaTek MT7621/7628/7688 SoCs
- bcm2835, i801, and tegra drivers got some more attention
- GPIO API cleanups
- cleanups in the core headers
- lots of usual driver updates"
* 'i2c/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (74 commits)
i2c: mt7621: Fix platform_no_drv_owner.cocci warnings
i2c: cpm: remove casting dma_alloc
dt-bindings: i2c: sun6i-p2wi: Fix the binding example
dt-bindings: i2c: mv64xxx: Fix the example compatible
i2c: i801: Documentation update
i2c: i801: Add support for Intel Tiger Lake
i2c: i801: Fix PCI ID sorting
dt-bindings: i2c-stm32: document optional dmas
i2c: i2c-stm32f7: Add I2C_SMBUS_I2C_BLOCK_DATA support
i2c: core: Tidy up handling of init_irq
i2c: core: Move ACPI gpio IRQ handling into i2c_acpi_get_irq
i2c: core: Move ACPI IRQ handling to probe time
i2c: acpi: Factor out getting the IRQ from ACPI
i2c: acpi: Use available IRQ helper functions
i2c: core: Allow whole core to use i2c_dev_irq_from_resources
eeprom: at24: modify a comment referring to platform data
dt-bindings: i2c: omap: Add new compatible for J721E SoCs
dt-bindings: i2c: mv64xxx: Add YAML schemas
dt-bindings: i2c: sun6i-p2wi: Add YAML schemas
i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver
...
- move the USB special case that bounced DMA through a device
bar into the USB code instead of handling it in the common
DMA code (Laurentiu Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed
during boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common
code and use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
-----BEGIN PGP SIGNATURE-----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=01Fr
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- move the USB special case that bounced DMA through a device bar into
the USB code instead of handling it in the common DMA code (Laurentiu
Tudor and Fredrik Noring)
- don't dip into the global CMA pool for single page allocations
(Nicolin Chen)
- fix a crash when allocating memory for the atomic pool failed during
boot (Florian Fainelli)
- move support for MIPS-style uncached segments to the common code and
use that for MIPS and nios2 (me)
- make support for DMA_ATTR_NON_CONSISTENT and
DMA_ATTR_NO_KERNEL_MAPPING generic (me)
- convert nds32 to the generic remapping allocator (me)
* tag 'dma-mapping-5.3' of git://git.infradead.org/users/hch/dma-mapping: (29 commits)
dma-mapping: mark dma_alloc_need_uncached as __always_inline
MIPS: only select ARCH_HAS_UNCACHED_SEGMENT for non-coherent platforms
usb: host: Fix excessive alignment restriction for local memory allocations
lib/genalloc.c: Add algorithm, align and zeroed family of DMA allocators
nios2: use the generic uncached segment support in dma-direct
nds32: use the generic remapping allocator for coherent DMA allocations
arc: use the generic remapping allocator for coherent DMA allocations
dma-direct: handle DMA_ATTR_NO_KERNEL_MAPPING in common code
dma-direct: handle DMA_ATTR_NON_CONSISTENT in common code
dma-mapping: add a dma_alloc_need_uncached helper
openrisc: remove the partial DMA_ATTR_NON_CONSISTENT support
arc: remove the partial DMA_ATTR_NON_CONSISTENT support
arm-nommu: remove the partial DMA_ATTR_NON_CONSISTENT support
ARM: dma-mapping: allow larger DMA mask than supported
dma-mapping: truncate dma masks to what dma_addr_t can hold
iommu/dma: Apply dma_{alloc,free}_contiguous functions
dma-remap: Avoid de-referencing NULL atomic_pool
MIPS: use the generic uncached segment support in dma-direct
dma-direct: provide generic support for uncached kernel segments
au1100fb: fix DMA API abuse
...
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while with
no reported issues. Nothing is earth-shattering, just constant forward
progress for more devices supported and cleanups and small fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed in.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXjYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynMYACgnSRP3GylwMywrkc9paVmDeiIgNwAn0N2sika
JEW7C3lkBJZJ7R6V/Ynm
=drla
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
- Add helpers to count items in a property array (Andy Shevchenko).
- Extend "software nodes" support to be more convenient for
representing device properties supplied by drivers (Heikki
Krogerus).
- Add device_find_child_by_name() helper to the driver core (Heikki
Krogerus).
- Extend device connection code to also look for references provided
via fwnode pointers (Heikki Krogerus).
- Start to register proper struct device objects for USB Type-C
muxes and orientation switches (Heikki Krogerus).
- Update the intel_cht_int33fe driver to describe devices in a more
general way with the help of "software nodes" (Heikki Krogerus).
-----BEGIN PGP SIGNATURE-----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=jOFk
-----END PGP SIGNATURE-----
Merge tag 'devprop-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These add helpers for counting items in a property array and extend
the "software nodes" support to be more convenient for representing
device properties supplied by drivers and make the intel_cht_int33fe
driver use that.
Specifics:
- Add helpers to count items in a property array (Andy Shevchenko).
- Extend "software nodes" support to be more convenient for
representing device properties supplied by drivers (Heikki
Krogerus).
- Add device_find_child_by_name() helper to the driver core (Heikki
Krogerus).
- Extend device connection code to also look for references provided
via fwnode pointers (Heikki Krogerus).
- Start to register proper struct device objects for USB Type-C muxes
and orientation switches (Heikki Krogerus).
- Update the intel_cht_int33fe driver to describe devices in a more
general way with the help of "software nodes" (Heikki Krogerus)"
* tag 'devprop-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add helpers to count items in an array
platform/x86: intel_cht_int33fe: Replacing the old connections with references
platform/x86: intel_cht_int33fe: Supply fwnodes for the external dependencies
platform/x86: intel_cht_int33fe: Provide fwnode for the USB connector
platform/x86: intel_cht_int33fe: Provide software nodes for the devices
platform/x86: intel_cht_int33fe: Remove unused fusb302 device property
platform/x86: intel_cht_int33fe: Register max17047 in its own function
usb: typec: Registering real device entries for the muxes
device connection: Find connections also by checking the references
device property: Introduce fwnode_find_reference()
ACPI / property: Don't limit named child node matching to data nodes
driver core: Add helper device_find_child_by_name()
software node: Add software_node_get_reference_args()
software node: Use kobject name when finding child nodes by name
software node: Add support for static node descriptors
software node: Simplify software_node_release() function
software node: Allow node creation without properties
-----BEGIN PGP SIGNATURE-----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=ABgl
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
- Some tiny improvements, no function change.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJdHrMsAAoJEEhZKYFQ1nG7jE0IAJXwiUh8Dd3IUkik8Nft3jGw
wPkiYfs9LGyQ6sJ8l4TxrbVvsnEs0n9dsExXP03MK6ow6Mqen5lHsa0VHkPeZX4C
+NyviJEH3BiY7jcWvhj8Sdp2/DBfulWPMTGZLncyNdinWGTrNQKzcDd7jzvp4Y1x
ZZSly0E0m5uU7ZP1QOw+/142+Mi+ia9bKl+xqkeKTwsaykYaYstfuVrpabFJ50FL
k8K1q0DCnF6G7aCGTBuVm0coe68TUcWIgl94BoZK6cSxEA4mJRU/VITYbR44dkBN
wHBJKIZzie4jAKLVXuRWix1eMiIDkeS9qKRGnc72hrF3eADlaikk9fwWLOQFjLk=
=hzIY
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
- Add imx7ulp support.
- Some tiny improvements, no function change.
* tag 'usb-ci-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: msm: Use devm_platform_ioremap_resource()
usb: chipidea: imx: Use devm_platform_ioremap_resource()
usb: chipidea: Use dev_err() instead of pr_err()
usb: chipidea: imx: "fsl,usbphy" phandle is not mandatory now
usb: chipidea: imx: add imx7ulp support
Convert the gadgetfs filesystem to the new internal mount API as the old
one will be obsoleted and removed. This allows greater flexibility in
communication of mount parameters between userspace, the VFS and the
filesystem.
See Documentation/filesystems/mount_api.txt for more information.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
cc: linux-usb@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit e70b3f5da0.
EJ writes:
Thinh found this patch might cause a failure in USB CV TD 9.13
Set Configuration Test. We are trying to fix it. Could you
please defer the merging of this patch until we fix it?
So am now dropping it.
Reported-by: EJ Hsu <ejh@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-5-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB erratum-A006918 workaround tries to start internal PHY inside
uboot (when PLL fails to lock). However, if the workaround also
fails, then USB initialization is also stopped inside Linux.
Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
node in device-tree. Presence of this node in device-tree is
used to stop USB controller initialization in Linux
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-4-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY_CLK_VALID bit for UTMI PHY in USBDR does not set even
if PHY is providing valid clock. Workaround for this
involves resetting of PHY and check PHY_CLK_VALID bit
multiple times. If PHY_CLK_VALID bit is still not set even
after 5 retries, it would be safe to deaclare that PHY
clock is not available.
This erratum is applicable for USBDR less then ver 2.4.
Signed-off-by: Suresh Gupta <B42813@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-2-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set USB_EN bit to select ULPI phy for USB controller version 2.5
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Link: https://lore.kernel.org/r/20190624072219.15258-1-yinbo.zhu@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing 4CC commands with tps6598x_write_4cc() already has
a pointer arg, don't reference it when using as arg to
tps6598x_block_write(). Correcting this enforces the constness
of the pointer to propagate to tps6598x_block_write(), so add
the const qualifier there to avoid the warning.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Portinfo bit field is 3 bits wide, not 2 bits. This led to
a wrong driver configuration for some tps6598x configurations.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If BLIST_TRY_VPD_PAGES is set for a device, even for an USB, it should
be honored, so only set skip_vpd_pages is try_vpd_pages is not set.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=ciUl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: more changes for v5.3 merge window
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
usb: phy: phy-mxs-usb: add imx7ulp support
doc: dt-binding: mxs-usb-phy: add compatible for 7ulp
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb:cdns3 Add Cadence USB3 DRD Driver
usb:gadget Simplify usb_decode_get_set_descriptor function.
usb:gadget Patch simplify usb_decode_set_clear_feature function.
usb:gadget Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: dwc3: pci: add support for TigerLake Devices
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable ret is being initialized with a value that is never read and
ret is being re-assigned immediately after the initialization in both
paths of an if statement. This is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use a 10000us AHB idle timeout in dwc2_core_reset() and make it
consistent with the other "wait for AHB master IDLE state" ocurrences.
This fixes a problem for me where dwc2 would not want to initialize when
updating to 4.19 on a MIPS Lantiq VRX200 SoC. dwc2 worked fine with
4.14.
Testing on my board shows that it takes 180us until AHB master IDLE
state is signalled. The very old vendor driver for this SoC (ifxhcd)
used a 1 second timeout.
Use the same timeout that is used everywhere when polling for
GRSTCTL_AHBIDLE instead of using a timeout that "works for one board"
(180us in my case) to have consistent behavior across the dwc2 driver.
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
fix below issue reported by coccicheck
drivers/usb/gadget/function/f_eem.c:169:7-12: Unneeded variable:
"value". Return "- EOPNOTSUPP" on line 179
We can not change return type of eem_setup as its registered with callback
function
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
At imx7ulp, the USB related analog register is located in PHY register
region too, so we need to control PLL at PHY driver directly.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.
Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.
To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.
The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.
Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.
Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.
Issue has been fixed for DEV_VER_V2 version of controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduce new Cadence USBSS DRD driver to Linux kernel.
The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch moves switch responsible for decoding descriptor type
outside snprintf. It improves code readability a little.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch adds usb_decode_test_mode and usb_decode_device_feature functions,
which allow to make more readable and simplify the
usb_decode_set_clear_feature function.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXRxL/gAKCRALxc3C7H1l
CKHnAQDsaOTD7f5Rhn2x0VapiuuxC3BcSHDgizmPcIt2f8F1yQEAgLvMy1//N75O
XTG6rLe6EsYc/fHj3csdgCURSMZVzQw=
=wAe3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.3-rc1
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for isodebug v1
USB: serial: option: add support for GosunCn ME3630 RNDIS mode
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
-----BEGIN PGP SIGNATURE-----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=3HLl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v5.3 merge window
The biggest part here is a set of patches removing unnecesary variables
from several drivers.
Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap.
Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based
SoCs.
DWC3 also got support for Intel Elkhart Lake platforms.
* tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits)
usb: dwc3: remove unused @lock member of dwc3_ep struct
usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices
usb: Replace snprintf with scnprintf in gether_get_ifname
usb: gadget: ether: Fix race between gether_disconnect and rx_submit
usb: gadget: storage: Remove warning message
usb: dwc3: gadget: Add support for disabling U1 and U2 entries
usb: gadget: send usb_gadget as an argument in get_config_params
doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2
usb: dwc3: qcom: Use of_clk_get_parent_count()
usb: dwc3: Fix core validation in probe, move after clocks are enabled
usb: dwc3: qcom: Improve error handling
usb: dwc3: qcom: Start USB in 'host mode' on the SDM845
usb: dwc3: qcom: Add support for booting with ACPI
soc: qcom: geni: Add support for ACPI
Revert "usb: dwc2: host: Setting qtd to NULL after freeing it"
usb: gadget: net2272: remove redundant assignments to pointer 's'
usb: gadget: Zero ffs_io_data
USB: omap_udc: Remove unneeded variable
fotg210-udc: Remove unneeded variable
usb: gadget: at91_udc: Remove unneeded variable
...
This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The PAGE_SHIFT alignment restriction to devm_gen_pool_create() quickly
exhaust local memory because most allocations are much smaller than
PAGE_SIZE. This causes USB device failures such as
usb 1-2.1: reset full-speed USB device number 4 using sm501-usb
sd 1:0:0:0: [sda] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=0x00
sd 1:0:0:0: [sda] tag#0 CDB: opcode=0x28 28 00 00 00 08 7c 00 00 f0 00
print_req_error: I/O error, dev sda, sector 2172 flags 80700
when trying to boot from the SM501 USB controller on SH4 with QEMU.
Align allocations as required but not necessarily much more than that.
The HCCA, TD and ED structures align with 256, 32 and 16 byte memory
boundaries, as specified by the Open HCI[1]. The min_alloc_order argument
to devm_gen_pool_create is now somewhat arbitrarily set to 4 (16 bytes).
Perhaps it could be somewhat lower for general buffer allocations.
Reference:
[1] "Open Host Controller Interface Specification for USB",
release 1.0a, Compaq, Microsoft, National Semiconductor, 1999,
pp. 16, 19, 33.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now the driver fixes the issue of the commit 482982062f ("usb:
gadget: renesas_usbhs: bugfix: don't modify platform data") by
using usbhs_mod_info.get_vbus, this patches uses the pointer
instead of copied value to avoid redundancy. Note that struct
renesas_usbhs_driver_param has to use copied value because
the driver has to set some members (e.g. buswait_bwait).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In device tree environment, the previous code allocates
renesas_usbhs_platform_info by using devm_kzalloc() and then copies
usbhs_of_data to the allocated memory. This reason is some values
(e.g. .platform_callback.get_vbus) are overwritten by the driver,
but the of_device_id.data is "const". Now the driver doesn't have
such a code, so this patch uses renesas_usbhs_platform_info on
of_device_id.data.
Note that the previous code set the pdev->dev.platform_data pointer
even if device tree environment, but the value is not used. So,
this patch also remove such a code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All platform related codes (rcar[23].c and rza{2}.c) has its own
.get_id function as "USBHS_GADGET". So, we can use a common
function for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c) to remove
usbhs_parse_dt(). So, this patch moves device tree properties
parsing to usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this can remove over 80 charactors in a line, this patch adds
struct device * declaration in usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c). So, to simplify
the source code, this patch adds a new flag has_new_pipe_configs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the dev_of_node macro instead of open coded
to be better.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now no one uses the type member so that this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To remove the type of renesas_usbhs_driver_param in the future, this
patch uses a specific flag "multi_clks".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The very old commit 482982062f ("usb: gadget: renesas_usbhs:
bugfix: don't modify platform data") changed to use copied whole
structures values to fix the "hung-up" issue. However, we also
can fix the issue if the driver copies the get_vbus function
pointer to the driver's value.
So, this patch adds get_vbus member into struct usbhs_mod_info and
use the pointer instead of struct renesas_usbhs_platform_callback.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, since other source code of this driver will use these
macros, this patch moves it to the header file.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notify_hotplug callback was supported in v3.10, but the last user
(armadillo800eva) was removed by the commit 1fa59bda21 ("ARM: shmobile:
Remove legacy board code for Armadillo-800 EVA"). So, this patch
removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the irq_vbus comments doesn't match with the current
implementation, this patch revises it. This patch also changes
new lines to reduce the source code lines.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current kernel, devio.c generates a number of compiler warnings
about taking the address of a member of a packed structure. The
warnings all look like this one:
drivers/usb/core/devio.c: In function ‘proc_do_submiturb’:
drivers/usb/core/devio.c:1489:43: warning: taking address of packed member of ‘struct usb_ctrlrequest’ may result in an unaligned pointer value [-Waddress-of-packed-member]
1489 | if (uurb->buffer_length < (le16_to_cpup(&dr->wLength) + 8)) {
| ^~~~~~~~~~~~
These warnings can easily be eliminated by changing various
le16_to_cpup() calls to use le16_to_cpu() instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4a2a8a2cce ("usbfs: private mutex for open, release, and
remove") is now obsolete. The commit was created back when we had
to handle both usbfs device nodes and the old usbdevfs filesystem
(/proc/bus/usb/), but usbdevfs no longer exists.
This means there's no longer any need to hold a mutex during two
separate removal operations (and thus during an entire notifier chain
call). Furthermore, the one remaining remove/release pair doesn't
race with open thanks to the synchronization provided by the device
model core in bus_find_device(). Remove and release don't race with
each other because they both run with the device lock held.
The upshot is that usbfs_mutex isn't needed any more. This patch
removes it entirely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc5' into patchwork
Linux 5.2-rc5
There are some media fixes on -rc5, so merge from it at media
devel tree.
* tag 'v5.2-rc5': (210 commits)
Linux 5.2-rc5
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
Smack: Restore the smackfsdef mount option and add missing prefixes
ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
module: Fix livepatch/ftrace module text permissions race
tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
tracing: Make two symbols static
tracing: avoid build warning with HAVE_NOP_MCOUNT
tracing: Fix out-of-range read in trace_stack_print()
gfs2: Fix rounding error in gfs2_iomap_page_prepare
x86/kasan: Fix boot with 5-level paging and KASAN
timekeeping: Repair ktime_get_coarse*() granularity
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
mm/devm_memremap_pages: fix final page put race
PCI/P2PDMA: track pgmap references per resource, not globally
lib/genalloc: introduce chunk owners
PCI/P2PDMA: fix the gen_pool_add_virt() failure path
mm/devm_memremap_pages: introduce devm_memunmap_pages
drivers/base/devres: introduce devm_release_action()
...
Replace ?: with min to calculate the number of bytes in the secondary buffer,
including changing the data type of data_in_secondary to size_t to be
type-consistent. data_in_secondary can never be negative.
Remove some spurious calculations (copy_to_user returns zero on success),
making one variable redundant (i)
This change does not alter the functionality of the code.
Signed-off-by: Daniel M German <dmg@turingmachine.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.
A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid the error-proneness of calls to sizeof() in the memcpy,
this patch uses struct assignment instead of memcpy.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>---
This patch is based on Greg's linux-usb.git / usb-next branch.
Note that mod_host.c also has memcpy but we cannot use struct assignment
for it because the type of urb->setup_patcket is just "unsigned char *".
drivers/usb/renesas_usbhs/common.c | 13 ++++---------
1 file changed, 4 insertions(+), 9 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a spelling typo in the function comment.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A single fix to take into account the PHY width during initialization of
dwc2 driver. This change allows deviceTree to pass PHY width if
necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=qmku
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.2-rc5
A single fix to take into account the PHY width during initialization of
dwc2 driver. This change allows deviceTree to pass PHY width if
necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'fixes-for-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc2: Use generic PHY width in params setup
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
snprintf returns the actual length of the buffer created; however,
this is not the case if snprintf truncates its parameter.
See https://lwn.net/Articles/69419/ for a detailed explanation.
The current code correctly handles this case at the expense
of extra code in the return statement.
scnprintf does returns the actual length of the buffer created
making the ?: operator unnecessary in the return
statement.
This change does not alter the functionality of the code.
Signed-off-by: Daniel M German <dmg@turingmachine.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
Fixes: 2b3d942c48 ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This change is to fix below warning message in following scenario:
usb_composite_setup_continue: Unexpected call
When system tried to enter suspend, the fsg_disable() will be called to
disable fsg driver and send a signal to fsg_main_thread. However, at
this point, the fsg_main_thread has already been frozen and can not
respond to this signal. So, this signal will be pended until
fsg_main_thread wakes up.
Once system resumes from suspend, fsg_main_thread will detect a signal
pended and do some corresponding action (in handle_exception()). Then,
host will send some setup requests (get descriptor, set configuration...)
to UDC driver trying to enumerate this device. During the handling of "set
configuration" request, it will try to sync up with fsg_main_thread by
sending a signal (which is the same as the signal sent by fsg_disable)
to it. In a similar manner, once the fsg_main_thread receives this
signal, it will call handle_exception() to handle the request.
However, if the fsg_main_thread wakes up from suspend a little late and
"set configuration" request from Host arrives a little earlier,
fsg_main_thread might come across the request from "set configuration"
when it handles the signal from fsg_disable(). In this case, it will
handle this request as well. So, when fsg_main_thread tries to handle
the signal sent from "set configuration" later, there will nothing left
to do and warning message "Unexpected call" is printed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Passing struct usb_gadget * as an extra argument in get_config_params
makes gadget drivers to easily update the U1DevExitLat & U2DevExitLat
values based on the values passed from the device tree. This patch
does the same
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The required clocks needs to be enabled before the first register
access. After commit fe8abf332b ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.
I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.
That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.
Fixes: b873e2d0ea ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument. If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.
Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When booting with Device Tree, the current default boot configuration
table option, the request to boot via 'host mode' comes from the
'dr_mode' property. A property of the same name can be used inside
ACPI tables too. However it is missing from the SDM845's ACPI tables
so we have to supply this information using Platform Device Properties
instead.
This does not change the behaviour of any currently supported devices.
The property is only set on ACPI enabled platforms, thus for H/W
booting DT, unless a 'dr_mode' property is present, the default is
still OTG (On-The-Go) as per [0]. Any new ACPI devices added will
also be able to over-ride this implementation by providing a 'dr_mode'
property in their ACPI tables. In cases where 'dr_mode' is omitted
from the tables AND 'host mode' should not be the default (very
unlikely), then we will have to add some way of choosing between them
at run time - most likely by ACPI HID.
[0] Documentation/devicetree/bindings/usb/generic.txt
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In Linux, the DWC3 core exists as its own independent platform device.
Thus when describing relationships in Device Tree, the current default
boot configuration table option, the DWC3 core often resides as a child
of the platform specific node. Both of which are given their own
address space descriptions and the drivers can be mostly agnostic to
each other.
However, other Operating Systems have taken a more monolithic approach,
which is evident in the configuration ACPI tables for the Qualcomm
Snapdragon SDM850, where all DWC3 (core and platform) components are
described under a single IO memory region.
To ensure successful booting using the supplied ACPI tables, we need to
devise a way to chop up the address regions provided and subsequently
register the DWC3 core with the resultant information, which is
precisely what this patch aims to achieve.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit b0d659022e.
The reverted commit does nothing but adding two unnecessary lines
of code. It sets a local variable to NULL in two functions, but
that variable is not used anywhere in the rest of those functions.
This is just confusing, so let's remove it.
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromiun.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The pointer 's' is being assigned however the pointer is
never used with either of these values before it it reassigned much
later on. I suspect it was going to be used in the output of the
main control registers scnprintf but was omitted. The assignments
of 's' to the driver name or the literal string are redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some cases the "Allocate & copy" block in ffs_epfile_io() is not
executed. Consequently, in such a case ffs_alloc_buffer() is never called
and struct ffs_io_data is not initialized properly. This in turn leads to
problems when ffs_free_buffer() is called at the end of ffs_epfile_io().
This patch uses kzalloc() instead of kmalloc() in the aio case and memset()
in non-aio case to properly initialize struct ffs_io_data.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the current implementation omap_udc_stop is always
returning -ENODEV.
Added changes to return 0 and remove variable status.
Issue identified with coccicheck
drivers/usb/gadget/udc/omap_udc.c:2106:6-12:
Unneeded variable: "status". Return "- ENODEV" on line 2128
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes below warning reported by coccicheck
drivers/usb/gadget/udc/fotg210-udc.c:484:5-8: Unneeded variable: "ret".
Return "0" on line 507
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
at91_wakeup is always returning -EINVAL.
But usb_gadget_wakeup expects 0 on success and negative number on
failure. As per current implementation this function wont fail.
This patch removes unneeded variable and returns 0.
Issue identified by coccicheck
drivers/usb/gadget/udc/at91_udc.c:802:6-12:
Unneeded variable: "status". Return "- EINVAL" on line 821
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The RZ/G2E cat874 board has a type-c connector connected to hd3ss3220 usb
type-c drp port controller. Enhance role switch support to assign the role
requested by connector device using the usb role switch class framework.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The following line of code in function ffs_epfile_io is trying to set
flag io_data->use_sg in case buffer required is larger than one page.
io_data->use_sg = gadget->sg_supported && data_len > PAGE_SIZE;
However at this point of time the variable data_len has not been set
to the proper buffer size yet. The consequence is that io_data->use_sg
is always set regardless what buffer size really is, because the condition
(data_len > PAGE_SIZE) is effectively an unsigned comparison between
-EINVAL and PAGE_SIZE which would always result in TRUE.
Fixes: 772a7a724f ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the 'snps,need-phy-for-wake' is set in the device tree then:
- We know that we can wakeup, so call device_set_wakeup_capable().
The USB core will use this knowledge to enable wakeup by default.
- We know that we should keep the PHY on during suspend if something
on our root hub needs remote wakeup. This requires the patch (USB:
Export usb_wakeup_enabled_descendants()). Note that we don't keep
the PHY on at suspend time if it's not needed because it would be a
power draw.
If we later find some users of dwc2 that can support wakeup without
keeping the PHY on we may want to add a way to call
device_set_wakeup_capable() without keeping the PHY on at suspend
time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Samsung Exynos SoCs require to force UTMI width to 8bit, otherwise the
host side of the shared USB2 PHY doesn't work.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 707d80f0a3 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support for the OTG ID change interrupt to switch between Host
and Device mode.
Tested on the Hardkernel Odroid-N2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting params.phy_utmi_width in dwc2_lowlevel_hw_init() is pointless since
it's value will be overwritten by dwc2_init_params().
This change make sure to take in account the generic PHY width information
during paraminitialisation, done in dwc2_set_param_phy_utmi_width().
By doing so, the phy_utmi_width params can still be overrided by
devicetree specific params and will also be checked against hardware
capabilities.
Fixes: 707d80f0a3 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add device tree probing to the fotg2 driver.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[Drop DMA mask coercion, drivers/of/platform.c does the job]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wusb code takes a very peculiar approach at implementing CBC-MAC,
by using plain CBC into a scratch buffer, and taking the output IV
as the MAC.
We can clean up this code substantially by switching to the cbcmac
shash, as exposed by the CCM template. To ensure that the module is
loaded on demand, add the cbcmac template name as a module alias.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently usfbs gained availability to retrieve device speed, but there
is sill no way to determine the bus number or list of ports the device
is connected to when using usbfs. While this information can be obtained
from sysfs, not all environments allow sysfs access. In a jailed
environment a program might be simply given an opened file descriptor to
usbfs device, and it is really important that all data can be gathered
from said file descriptor.
This patch introduces a new ioctl, USBDEVFS_CONNINFO_EX, which return
extended connection information for the device, including the bus
number, address, port list and speed. The API allows kernel to extend
amount of data returned by the ioctl and userspace has an option of
adjusting the amount of data it is willing to consume. A new capability,
USBDEVFS_CAP_CONNINFO_EX, is introduced to help userspace in determining
whether the kernel supports this new ioctl.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang produces the following warning
drivers/usb/host/xhci-tegra.c:357:27: warning: unused variable
'mbox_cmd_name' [-Wunused-const-variable]
static const char * const mbox_cmd_name[] = {
Looks like it was intended for logging or debugging, but was
never implemented. Removing mbox_cmd_name.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/533
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
While at it also add the missing newlines.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Since the chipidea common code support get the USB PHY phandle from
"phys", the glue layer is not mandatory to get the "fsl,usbphy" phandle
any more.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In this commit, we add CI_HDRC_PMQOS to avoid system entering idle,
at imx7ulp, if the system enters idle, the DMA will stop, so the USB
transfer can't work at this case.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It's not needed after [1] is applied, because usb_debug_root is created
by usb common core but not usbcore now.
[1] 812086d362 ("USB: move usb debugfs directory creation to the usb common core")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unneeded variable ret in function sisusb_set_default_mode.
Change return type of sisusb_set_default_mode from int to void
as it never fails.
Issue identified by coccicheck
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
-----
changes in v2: Change return type of sisusb_set_default_mode from int to
void as it never fails
changes in v3: Update changelog
----
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for option and pl2303.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXP5fMgAKCRALxc3C7H1l
CJEKAQDuzkjsWiJhaUXlWN//bUVOzZWwsRdm1d9K6B1ns/9H1AD/bz/WsaaqT4PG
v2kmr4ydrrxEqaO0eQWRrqSfnCF32w0=
=do74
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.2-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.2-rc5
Here are some new device ids for option and pl2303.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.2-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit 0x1260 and 0x1261 compositions
USB: serial: pl2303: add Allied Telesis VT-Kit3
USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC2 gets a fix for zlp handling which allows DWC2 to pass USBCV MSC
tests.
A memory leak in fusb300 was plugged.
DWC2 also got a fix for wMaxPacketSize handling while acting as host
which fixes a regression with USB Cameras.
Apart from these, the usual set of minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=1yqY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.2-rc4
DWC2 gets a fix for zlp handling which allows DWC2 to pass USBCV MSC
tests.
A memory leak in fusb300 was plugged.
DWC2 also got a fix for wMaxPacketSize handling while acting as host
which fixes a regression with USB Cameras.
Apart from these, the usual set of minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'fixes-for-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe()
usb: gadget: dwc2: fix zlp handling
usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA
usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC
usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i]
usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()
usb: dwc2: Fix DMA cache alignment issues
usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression)
Cypress USB Type-C CCGx controller firmware version 3.1.10
(which is being used in many NVIDIA GPU cards) has known issue of
not triggering interrupt when a USB device is hot plugged to runtime
resume the controller. If any GPU card gets latest kernel with runtime
pm support but does not get latest fixed firmware then also it should
continue to work and therefore a workaround is required to check for
any connector change event.
The workaround is that i2c bus driver will call pm_request_resume()
to runtime resume ucsi_ccg driver. CCG driver will call the ISR
for any connector change event for NVIDIA GPU card and only if it has
old CCG firmware with the known issue.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change enables runtime pm support to UCSI CCG driver.
Added ucsi_resume() function to enable notification after
system reusme. Exported both ucsi_resume() and ucsi_send_command()
symbols in ucsi.c for modular build.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
This issue was detected by using the Coccinelle software.
Fixes: 408b56ca5c ("usb: gadget: udc: lpc32xx: simplify probe")
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The patch 10209abe87
usb: dwc2: gadget: Add scatter-gather mode
avoided a NULL pointer dereference (hs_ep->req == NULL) by
calling dwc2_gadget_fill_nonisoc_xfer_dma_one() directly instead of through
the dwc2_gadget_config_nonisoc_xfer_ddma() wrapper, which unconditionally
dereferenced the said pointer.
However, this was based on an incorrect assumption that in the context of
dwc2_hsotg_program_zlp() the pointer is always NULL, which is not the case.
The result were SB CV MSC tests failing starting from Test Case 6.
Instead, this patch reverts to calling the wrapper and adds a check for
the pointer being NULL inside the wrapper.
Fixes: 10209abe87 (usb: dwc2: gadget: Add scatter-gather mode)
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On ISOC OUT transfer completion, in none DDMA mode, set actual frame
number returning to function driver in usb_request.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget drivers may queue request in interrupt context. This would lead to
a descriptor allocation in that context. In that case we would hit
BUG_ON(in_interrupt()) in __get_vm_area_node.
Also remove the unnecessary cast.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: James Grant <jamesg@zaltys.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no deallocation of fusb300->ep[i] elements, allocated at
fusb300_probe.
The patch adds deallocation of fusb300->ep array elements.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since this driver already handles changer detction state, copy the
workaround code currently residing in arch/arm/mach-imx/anatop.c into
this drier to consolidate the places modifying it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Insert a padding between data and the stored_xfer_buffer pointer to
ensure they are not on the same cache line.
Otherwise, the stored_xfer_buffer gets corrupted for IN URBs on
non-cache-coherent systems. (In my case: Lantiq xRX200 MIPS)
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Fixes: 56406e017a ("usb: dwc2: Fix DMA alignment to start at allocated boundary")
Cc: <stable@vger.kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In commit abb621844f ("usb: ch9: make usb_endpoint_maxp() return
only packet size") the API to usb_endpoint_maxp() changed. It used to
just return wMaxPacketSize but after that commit it returned
wMaxPacketSize with the high bits (the multiplier) masked off. If you
wanted to get the multiplier it was now up to your code to call the
new usb_endpoint_maxp_mult() which was introduced in
commit 541b6fe630 ("usb: add helper to extract bits 12:11 of
wMaxPacketSize").
Prior to the API change most host drivers were updated, but no update
was made to dwc2. Presumably it was assumed that dwc2 was too
simplistic to use the multiplier and thus just didn't support a
certain class of USB devices. However, it turns out that dwc2 did use
the multiplier and many devices using it were working quite nicely.
That means that many USB devices have been broken since the API
change. One such device is a Logitech HD Pro Webcam C920.
Specifically, though dwc2 didn't directly call usb_endpoint_maxp(), it
did call usb_maxpacket() which in turn called usb_endpoint_maxp().
Let's update dwc2 to work properly with the new API.
Fixes: abb621844f ("usb: ch9: make usb_endpoint_maxp() return only packet size")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB gadget subsystem wants to use the USB debugfs root directory, so
move it to the common "core" USB code so that it is properly initialized
and removed as needed.
In order to properly do this, we need to load the common code before the
usb core code, when everything is linked into the kernel, so reorder the
link order of the code.
Also as the usb common code has the possibility of the led trigger logic
to be merged into it, handle the build option properly by only having
one module init/exit function and have the common code initialize the
led trigger if needed.
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
But this only really works if all drivers use this, so convert
this UVC gadget driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vhci_send_cmd_unlink() declears kvec array of size 3 but it actually
uses just one element of the array. So, remove kvec array and replace
it with single kvec variable.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Controlling PWMEN/EXTLP (named as "has_otg") was supported in v3.2,
but the last user (kzm9g) was removed by the commit 30f8925a57
("ARM: shmobile: Remove legacy board code for KZM-A9-GT"). So, this
patch remove it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SUDMAC feature was supported in v3.10, but was never used by
any platform. So, this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt
processing for full-/low-speed endpoints connected via a TT, the host
software must use the Clear_TT_Buffer request to the TT to ensure
that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high-
speed hub (ConferenceCam Connect), sometimes once we get STALL on a
request we may continue to get STALL with the folllowing requests,
like Set_Interface.
Here we invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer
request to the hub of the device for the following Set_Interface
requests to the device to get ACK successfully.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Clear_TT_Buffer request sent to the hub includes the address of
the LS/FS child device in wValue field. usb_hub_clear_tt_buffer()
uses udev->devnum to set the address wValue. This won't work for
devices connected to xHC.
For other host controllers udev->devnum is the same as the address of
the usb device, chosen and set by usb core. With xHC the controller
hardware assigns the address, and won't be the same as devnum.
Here we add devaddr in "struct usb_device" for
usb_hub_clear_tt_buffer() to use.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the chipmunk-like voice that manifets randomly when
using the integrated mic of the Logitech Webcam HD C270.
The issue was solved initially for this device by commit 2394d67e44
("USB: add RESET_RESUME for webcams shown to be quirky") but it was then
reintroduced by e387ef5c47 ("usb: Add USB_QUIRK_RESET_RESUME for all
Logitech UVC webcams"). This patch is to have the fix back.
Signed-off-by: Marco Zatta <marco@zatta.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one more Realtek card reader requires ums-realtek to work
correctly.
Add the device ID to support it.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the addition of the local memory allocator, the HCD_LOCAL_MEM
flag can be dropped and the checks against it replaced with a check
for the localmem_pool ptr being initialized.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For HCs that have local memory, replace the current DMA API usage with
a genalloc generic allocator to manage the mappings for these devices.
To help users, introduce a new HCD API, usb_hcd_setup_local_mem() that
will setup up the genalloc backing up the device local memory. It will
be used in subsequent patches. This is in preparation for dropping
the existing "coherent" dma mem declaration APIs. The current
implementation was relying on a short circuit in the DMA API that in
the end, was acting as an allocator for these type of devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/phy/phy-mv-usb.c: In function mv_otg_work:
drivers/usb/phy/phy-mv-usb.c:404:18: warning: variable phy set but not used [-Wunused-but-set-variable]
It's no used since commit e47d92545c ("usb: move
the OTG state from the USB PHY to the OTG structure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/ohci-spear.c: In function spear_ohci_hcd_drv_probe:
drivers/usb/host/ohci-spear.c:38:19: warning: variable ohci set but not used [-Wunused-but-set-variable]
It is never used since commit 1cc6ac59ff ("USB:
OHCI: make ohci-spear a separate driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have the correct SPDX tag for the ueagle-atm.c file, the
wall of "boiler-plate" text is not needed.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Damien Bergamini <damien.bergamini@free.fr>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas rightly points out that I got the BSD clause count wrong for this
driver, it should be 2, not 3 based on the text in the license here, so
fix that up.
He also raises the question that the license text points to a v2 only
license, yet the text in the header says "or later". Given that the
text in the header says "or later" and all of the other USB atm drivers
are licensed in that way, I am going to leave the string as-is for that
mark.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Damien Bergamini <damien.bergamini@free.fr>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/ohci-s3c2410.c: In function s3c2410_hcd_oc:
drivers/usb/host/ohci-s3c2410.c:296:18: warning: variable hcd set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable rv is assigned with a value that is never read and
it is re-assigned a new value on the next statement. The
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/ohci-st.c: In function st_ohci_platform_probe:
drivers/usb/host/ohci-st.c:135:19: warning: variable ohci set but not used [-Wunused-but-set-variable]
It's never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/ehci-st.c: In function st_ehci_platform_probe:
drivers/usb/host/ehci-st.c:155:19: warning: variable ehci set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case memory resources for *fw* were successfully allocated,
release them before return.
Addresses-Coverity-ID: 1445499 ("Resource leak")
Fixes: 5c9ae5a875 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering real device entries (struct device) for the mode
muxes as well as for the orientation switches.
The Type-C mux code was deliberately attempting to avoid
creation of separate device entries for the orientation
switch and the mode switch (alternate modes) because they
are not physical devices. They are functions of a single
physical multiplexer/demultiplexer switch device.
Unfortunately because of the dependency we still have on the
underlying mux device driver, we had to put in hacks like
the one in the commit 3e3b81965c ("usb: typec: mux: Take
care of driver module reference counting") to make sure the
driver does not disappear from underneath us. Even with
those hacks we were still left with a potential NUll pointer
dereference scenario, so just creating the device entries,
and letting the core take care of the dependencies. No more
hacks needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can also use this API to find named references that the
device nodes have by using fwnode_property_get_reference_args()
function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the following sparse context imbalance regression introduced in
a patch that fixed sleeping function called from invalid context bug.
kbuild test robot reported on:
tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus
Regressions in current branch:
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
Error ids grouped by kconfigs:
recent_errors
├── i386-allmodconfig
│ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line
├── x86_64-allmodconfig
│ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block
│ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block
└── x86_64-allyesconfig
└── drivers-usb-usbip-stub_dev.c:second-lock-on-line
This is a real problem in an error leg where spin_lock() is called on an
already held lock.
Fix the imbalance in stub_probe() and stub_disconnect().
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 0c9e8b3cad ("usbip: usbip_host: fix BUG: sleeping function called from invalid context")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb is not attached, it's unnessary to allocate, copy
and free memory
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb support for asyncio encoded one of it's values in the wrong
field. It should have used si_value but instead used si_addr which is
not present in the _rt union member of struct siginfo.
The practical result of this is that on a 64bit big endian kernel
when delivering a signal to a 32bit process the si_addr field
is set to NULL, instead of the expected pointer value.
This issue can not be fixed in copy_siginfo_to_user32 as the usb
usage of the the _sigfault (aka si_addr) member of the siginfo
union when SI_ASYNCIO is set is incompatible with the POSIX and
glibc usage of the _rt member of the siginfo union.
Therefore replace kill_pid_info_as_cred with kill_pid_usb_asyncio a
dedicated function for this one specific case. There are no other
users of kill_pid_info_as_cred so this specialization should have no
impact on the amount of code in the kernel. Have kill_pid_usb_asyncio
take instead of a siginfo_t which is difficult and error prone, 3
arguments, a signal number, an errno value, and an address enconded as
a sigval_t. The encoding of the address as a sigval_t allows the
code that reads the userspace request for a signal to handle this
compat issue along with all of the other compat issues.
Add BUILD_BUG_ONs in kernel/signal.c to ensure that we can now place
the pointer value at the in si_pid (instead of si_addr). That is the
code now verifies that si_pid and si_addr always occur at the same
location. Further the code veries that for native structures a value
placed in si_pid and spilling into si_uid will appear in userspace in
si_addr (on a byte by byte copy of siginfo or a field by field copy of
siginfo). The code also verifies that for a 64bit kernel and a 32bit
userspace the 32bit pointer will fit in si_pid.
I have used the usbsig.c program below written by Alan Stern and
slightly tweaked by me to run on a big endian machine to verify the
issue exists (on sparc64) and to confirm the patch below fixes the issue.
/* usbsig.c -- test USB async signal delivery */
#define _GNU_SOURCE
#include <stdio.h>
#include <fcntl.h>
#include <signal.h>
#include <string.h>
#include <sys/ioctl.h>
#include <unistd.h>
#include <endian.h>
#include <linux/usb/ch9.h>
#include <linux/usbdevice_fs.h>
static struct usbdevfs_urb urb;
static struct usbdevfs_disconnectsignal ds;
static volatile sig_atomic_t done = 0;
void urb_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p urb: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &urb);
printf("%s\n", (info->si_addr == &urb) ? "Good" : "Bad");
}
void ds_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p ds: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &ds);
printf("%s\n", (info->si_addr == &ds) ? "Good" : "Bad");
done = 1;
}
int main(int argc, char **argv)
{
char *devfilename;
int fd;
int rc;
struct sigaction act;
struct usb_ctrlrequest *req;
void *ptr;
char buf[80];
if (argc != 2) {
fprintf(stderr, "Usage: usbsig device-file-name\n");
return 1;
}
devfilename = argv[1];
fd = open(devfilename, O_RDWR);
if (fd == -1) {
perror("Error opening device file");
return 1;
}
act.sa_sigaction = urb_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR1, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
act.sa_sigaction = ds_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR2, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
memset(&urb, 0, sizeof(urb));
urb.type = USBDEVFS_URB_TYPE_CONTROL;
urb.endpoint = USB_DIR_IN | 0;
urb.buffer = buf;
urb.buffer_length = sizeof(buf);
urb.signr = SIGUSR1;
req = (struct usb_ctrlrequest *) buf;
req->bRequestType = USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE;
req->bRequest = USB_REQ_GET_DESCRIPTOR;
req->wValue = htole16(USB_DT_DEVICE << 8);
req->wIndex = htole16(0);
req->wLength = htole16(sizeof(buf) - sizeof(*req));
rc = ioctl(fd, USBDEVFS_SUBMITURB, &urb);
if (rc == -1) {
perror("Error in SUBMITURB ioctl");
return 1;
}
rc = ioctl(fd, USBDEVFS_REAPURB, &ptr);
if (rc == -1) {
perror("Error in REAPURB ioctl");
return 1;
}
memset(&ds, 0, sizeof(ds));
ds.signr = SIGUSR2;
ds.context = &ds;
rc = ioctl(fd, USBDEVFS_DISCSIGNAL, &ds);
if (rc == -1) {
perror("Error in DISCSIGNAL ioctl");
return 1;
}
printf("Waiting for usb disconnect\n");
while (!done) {
sleep(1);
}
close(fd);
return 0;
}
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: v2.3.39
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Commit 597c56e372 ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:
drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]
Use %zu for printing size_t type in order to fix the warnings.
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.
Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.
[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci immediate data transfer (IDT) support in 5.2-rc1 caused regression
on various Samsung Exynos boards with ASIX USB 2.0 ethernet dongle.
If the transfer buffer in the URB is already DMA mapped then IDT should
not be used. urb->transfer_dma will already contain a valid dma address,
and there is no guarantee the data in urb->transfer_buffer is valid.
The IDT support patch used urb->transfer_dma as a temporary storage,
copying data from urb->transfer_buffer into it.
Issue was solved by preventing IDT if transfer buffer is already dma
mapped, and by not using urb->transfer_dma as temporary storage.
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_debugfs_create_slot(), kzalloc() can fail and
dev->debugfs_private will be NULL.
In xhci_debugfs_create_endpoint(), dev->debugfs_private is used without
any null-pointer check, and can cause a null pointer dereference.
To fix this bug, a null-pointer check is added in
xhci_debugfs_create_endpoint().
This bug is found by a runtime fuzzing tool named FIZZER written by us.
[subjet line change change, add potential -Mathais]
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.
While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.
Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Telit LE910Cx 0x1260 and 0x1261 compositions.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is adds the vendor and device id for the AT-VT-Kit3 which is a
pl2303-based device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
