Corrections:
* Remove non-existing STBE region from Ether-AVB node in DT of
R-Car E3 (r8a77990) SoC
This region does not exist on this SoC
Cleanups:
* Consistently use rwdt as label for Renesas Watchdog Timer devices
* Add second port to rcar_sound placeholder in DT of R-Car M3-N (r8a77965) SoC
Nodes with #address-cells/#size-cells should have more than one child node
* Fix adv7482 decimal unit addresses in DT of Salvator-X and -XS boards
Addresses are assumed to be hex by dtc, thus it is not valid to use
decimal
Enhancements:
* Describe in DT:
- INTC-EX of R-Car V3H (r8a77980) SoC
- USB3.0 of R-Car E3 (r8a77980) SoC
- All SCIF and HSCIF devices of R-Car D3 (r8a77995) SoC.
Previously only SCIF2, used as the debug consile, was described.
- All IPMMU devicesof R-Car M3-N (r8a77965), V3H (r8a77980) and
E3 (r8a77990) SoCs
* Enable USB3.0 in DT of R-Car E3 (r8a77980) based Ebisu board
* Prefer HSCIF1 over SCIF1 in DT of Salvator-X and -XS boards
HSCIF is superior to SCIF (larger FIFOs, more accurate and wider
supported range of bitrates).
-----BEGIN PGP SIGNATURE-----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=yZLk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.19
Corrections:
* Remove non-existing STBE region from Ether-AVB node in DT of
R-Car E3 (r8a77990) SoC
Cleanups:
* Consistently use rwdt as label for Renesas Watchdog Timer devices
* Add second port to rcar_sound placeholder in DT of R-Car M3-N (r8a77965) SoC
* Fix adv7482 decimal unit addresses in DT of Salvator-X and -XS boards
Enhancements:
* Describe in DT:
- INTC-EX of R-Car V3H (r8a77980) SoC
- USB3.0 of R-Car E3 (r8a77980) SoC
- All SCIF and HSCIF devices of R-Car D3 (r8a77995) SoC.
Previously only SCIF2, used as the debug consile, was described.
- All IPMMU devicesof R-Car M3-N (r8a77965), V3H (r8a77980) and
E3 (r8a77990) SoCs
* Enable USB3.0 in DT of R-Car E3 (r8a77980) based Ebisu board
* Prefer HSCIF1 over SCIF1 in DT of Salvator-X and -XS boards
* tag 'renesas-arm64-dt2-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77980: add INTC-EX support
arm64: dts: renesas: r8a77990: Enable USB3.0 host for Ebisu board
arm64: dts: renesas: r8a77995: Add SCIF {0,1,3,4,5} and all HSCIF device nodes
arm64: dts: renesas: r8a779{65,80,90}: Add IPMMU devices nodes
arm64: dts: renesas: Unify the labels for RWDT
arm64: dts: renesas: salvator-common: Prefer HSCIF1 over SCIF1
arm64: dts: renesas: r8a77965: Add second port to rcar_sound placeholder
arm64: dts: renesas: salvator-common: Fix adv7482 decimal unit addresses
arm64: dts: renesas: r8a77990: Remove non-existing STBE region
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
- fix the PMC compatibles
-----BEGIN PGP SIGNATURE-----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=XVdU
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
AT91 DT for 4.19:
- New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
- fix the PMC compatibles
* tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: fix typos for SSC TD functions
ARM: dts: add support for Laird SOM60 module and DVK boards
ARM: dts: add support for Gatwick board based on WB50N
ARM: dts: add support for Laird WB50N cpu module and DVK
ARM: dts: add support for Laird WB45N cpu module and DVK
ARM: dts: at91: add labels to soc dtsi for derivative boards
dt-bindings: add laird and giantec vendor prefix
ARM: dts: fix PMC compatible
ARM: at91: fix USB clock detection handling
dt-bindings: clk: at91: Document all the PMC compatibles
dt-bindings: arm: remove PMC bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (clocks, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Tidy up MMC properties for hi3660
- Remove keep-power-in-suspend on hikey and hikey960 to
avoid keeping wifi power during suspend and let the
user enable it if required
- Update idle states for hikey960
- Add missing cooling device properties for cpus on hi6220
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=070t
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.19v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.19v2
- Tidy up MMC properties for hi3660
- Remove keep-power-in-suspend on hikey and hikey960 to
avoid keeping wifi power during suspend and let the
user enable it if required
- Update idle states for hikey960
- Add missing cooling device properties for cpus on hi6220
* tag 'hisi-arm64-dt-for-4.19v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add missing cooling device properties for CPUs
arm64: hikey960: update idle-states
arm64: dts: hikey: Remove keep-power-in-suspend property
arm64: dts: hikey960: Remove keep-power-in-suspend property
arm64: dts: hikey960: Clean up MMC properties and move to proper file
arm64: dts: hikey960: Remove deprecated MMC properties
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.
-----BEGIN PGP SIGNATURE-----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=h3F9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Few more beaglebone variants for v4.19 merge window
This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.
* tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: add am335x-sancloud-bbe board support
dt-bindings: Add vendor prefix for Sancloud
ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED based on TI AM335x
Signed-off-by: Olof Johansson <olof@lixom.net>
Describe the INTC-EX interrupt controller in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device nodes for SCIF {0,1,3,4,5} and all HSCIF serial
ports, incl. clocks, power domain and DMAs.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix typo for TD function of pins PIN_PB22 and PIN_PC14
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds upcoming SOM module, featuring Marvell WiFi
and Bluetooth, 2Gb NAND / 1Gb LPDDR SDRAM, and an Atmel SAMA5D3 CPU.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for the LoRa gateway from Laird, the RG1xx.
This board houses the WB50NBT CPU module along with a Semtech SX1301 based
concentrator card.
https://www.lairdtech.com/products/rg1xx-lora-gateway
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds CPU module, featuring Atheros wifi, CSR
Bluetooth and, Atmel SAMA5D3 CPU.
https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-module
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds support for Lairds combo CPU module, featuring on board
Atheros wifi, CSR Bluetooth radio and, Atmel CPU.
https://www.lairdtech.com/products/wb45nbt
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add an LED node, connected to the Processing System (PS)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include GPIO dt-bindings and use GPIO_ACTIVE_* constants
to improve readability
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
According to the reference manual, the board has two Micron
MT41K256M16HA-125 DDR3L memory ICs, which have 512 MiB each
Tested on a ZYBO-Z7-20 board
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The bindings were missing when the device-tree
files were added
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the Adapteva Parallela board to Xilinx dt-bindings,
as it's based on a Zynq SoC from Xilinx
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sort additional compatible strings (boards) alphabetically
by their manufacturer and model number
This will help when finding a board because they
will be grouped by their manufacturer
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the description of some boards to make it similar
to the value of the model property from their respective
device-tree, using the format "<manufacturer> <model>"
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a dts for MYIR Z-turn board and respective target in Makefile.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avnet Ultra96 rev1 board is commercialized Xilinx zcu100 revC/D
internal board. The patch is reusing zcu100 revC files but changing
model description and compatible strings which are used for example by
libmraa.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline started to use serdev interface for uart attached devices.
Change description to reflect it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds GPIO for headphone detection on LD11 global board.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds GPIO for headphone detection on LD20 global board.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Do minor rearrangement as well to keep ordering consistent.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Update entry/exit latency and residency time of hikey960 to use more
realistic figures based on unitary tests done on the platform.
The complete results (in us) :
big cluster
cluster CPU
max entry latency 800 400
max exit latency 2900 550
residency 903Mhz 5000 1500
residency 2363Mhz 0 1500
little cluster
cluster CPU
max entry latency 500 400
max exit latency 1600 650
residency 533Mhz 8000 4500
residency 1844Mhz 0 1500
We can see that the residency time depends of the running OPP which is not
handled for now. Then we also have to take into account the constraint of
a residency time shorter than the tick to get full advantage of idle loop
reordering(tick is stopped if idle duration is higher than tick period).
Finally the selected residency value are :
big cluster
cluster CPU
residency 3700 1500
little cluster
cluster CPU
residency 3500 1500
A simple test with a task waking up every 11.111ms shows improvement:
- 5% a lowest OPP
- 22% at highest OPP
The period has been chosen:
- to be shorter than old cluster residency time and longer than new
residency time of cluster off C-state
- to prevent any sync with tick (4ms) when running tests that can add
some variances between tests
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Remove the keep-power-in-suspend property because it keeps wifi power
on during suspend. This property is only required when enabling WoWLAN
and should only be enabled based on need.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Remove the keep-power-in-suspend property because it keeps wifi power
on during suspend. This property is only required when enabling WoWLAN
and should only be enabled based on need. Also remove dupplicate property
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Certain properties should be moved to the board file to reflect
the specific properties of the board, and not the SoC. Move these
properties to proper location and organize properties in both files.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.
This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]
https://octavosystems.com/octavo_products/osd3358-sm-red/
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add IPMMU device nodes for the R-Car M3-N (r8a77965),
V3H (r8a77980) and E3 (r8a77990) SoCs.
* The r8a77965 IPMMU is quite similar to r8a7796 however VP0
has been added and PV1 has been removed. Also the IMSSTR
bit assignment has been reworked.
* The r8a77980 IPMMU is quite similar to r8a77970 however VC0
has been added. The IMSSTR bit assignment has also been
reworked. Power domains are also quite different however the
the documentation is rather unclear about this topic.
Until we know better VC0 gets assigned to R8A77980_PD_ALWAYS_ON.
* The r8a77990 IPMMU is similar to r8a77995. Power domains are
however different and the public documentation is still unclear.
Based on preliminary information from the hardware team the R-Car E3
SoC comes with an IPMMU-VP0 device in an Always-on power domain and
the IPMMU-VC0 is placed as expected in the A3VC power domain.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Add Vitesse switch chips
- Add a new DT for a reference design
-----BEGIN PGP SIGNATURE-----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=3RrW
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.19:
- Add Vitesse switch chips
- Add a new DT for a reference design
* tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add devicetree for Storlink/Storm SL93512R
ARM: dts: Add Vitesse G5e switch to the Gemini SQ201
ARM: dts: Add WAN ethernet port to the SQ201
Signed-off-by: Olof Johansson <olof@lixom.net>
The Storlink Gemini324 EV-Board also known as Storm
Semiconductor SL93512R_BRD is ground zero for the Gemini
devices. We add a device tree so we can support it, it
turns out to be pretty trivial.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
