In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-31
This series contains updates to the ice driver only.
Brett modifies the driver to allow users to clear a VF's
administratively set MAC address on the PF. Fixes the driver to
recognize an existing VLAN tag when DMAC/SMAC is enabled in a packet.
Fixes an issue, so that VF's are reset after any VF port VLAN
modifications are made on the PF. Made sure the register QRXFLXP_CNTXT
is cleared before writing a new value to ensure the previous value is
not passed forward. Updates the PF to allow the VF to request a reset
as soon as it has been initialized. Fixes an issue to ensure when a VSI
is created, it uses the current coalesce value, not the default value.
Paul allows untrusted VF's to add 16 filters.
Dan increases the timeout needed after a PFR to allow ample time for
package download.
Chinh adjust the define value for the number of PHY speeds we currently
support. Changes the driver to ignore EMODE error when configuring the
PHY.
Jesse fixes an issue which was preventing a user from configuring the
interface before bringing it up.
Henry fixes the logic for adding back perfect flows after flow director
filter does a deletion.
Bruce fixes line wrappings to make it more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.
Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.
With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.
Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class. This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.
Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.
Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.
A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:
1. Packets might not need to be marked with 'offload_fwd_mark'. For
example, if packet was trapped before L2 forwarding
2. Packets might not need to be injected to the kernel's Rx path. For
example, sampled packets are reported to user space via the psample
module
Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9 ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties. The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.
However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions. E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.
As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary. Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC. However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.
Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay. This also fixes messages
like:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"
as the PHY no longer sees the original RGMII-*ID mode.
Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to the ice driver only.
Anirudh (Ani) adds a poll for reset completion before proceeding with
driver initialization when the DDP package fails to load and the firmware
issues a core reset.
Jake cleans up unnecessary code, since ice_set_dflt_vsi_ctx() performs a
memset to clear the info from the context structures. Fixed a potential
double free during probe unrolling after a failure. Also fixed a
potential NULL pointer dereference upon register_netdev() failure.
Tony makes two functions static which are not called outside of their
file.
Brett refactors the ice_ena_vf_mappings(), which was doing the VF's MSIx
and queue mapping in one function which was hard to digest. So create a
new function to handle the enabling MSIx mappings and another function
to handle the enabling of queue mappings. Simplify the code flow in
ice_sriov_configure(). Created a helper function for clearing
VPGEN_VFRTRIG register, as this needs to be done on reset to notify the
VF that we are done resetting it. Fixed the initialization/creation and
reset flows, which was unnecessarily complicated, so separate the two
flows into their own functions. Renamed VF initialization functions to
make it more clear what they do and why. Added functionality to set the
VF trust mode bit on reset. Added helper functions to rebuild the VLAN
and MAC configurations when resetting a VF. Refactored how the VF reset
is handled to prevent VF reset timeouts.
Paul cleaned up code not needed during a CORER/GLOBR reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify handling the power management callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7R3wcACgkQSD+KveBX
+j6/ZQf/QD39naPeImfLjemkRK9L+TKbS4nU6wpUwf1jC33Wdm4HhkhsWEnR6C4l
OwU/Pae3I9EtKP4gRE0W1o8h7zC9h4hY7+IKZOdyQ32iUY55PX/H25oqAiCj1NCM
xzWpXOTwK/vkqmkCedAd+YpNdYlbOhfycr+KVPSsvFdaPqjzfNO1PJcLsUbAbzrX
A+8pYdhUYTtx1N3YHJL5abLN6WzMAKxgwlm9GG8YCXACTJT6CBWWHGebVsC5TDUk
Lj5hJj38mI8/3dcu6vWP0kLGVfRZo0HS/gpPGxbKQFpP+1uBYaRENAQONxkY++6S
GDPix7ccvN+yNMlON893PC/Cogw3Yg==
=WaCJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-cleanup-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_VLAN_CTAG_FILTER is not set in netdev->hw_feature for
the HNS3 driver, so the handler of NETIF_F_HW_VLAN_CTAG_FILTER
in hns3_nic_set_features() won't be called, remove it.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a redundant blank line in hclgevf_cmd_set_promisc_mode(),
and fix a reverse xmas tree coding style issue in
hclgevf_set_rss_tc_mode().
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hclgevf_dev stands for VF device, its field num_tqps
indicates the number of VF's task queue pairs, so the comment
is incorrect, replace 'PF' with 'VF'.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro hclgevf_ring_to_dma_dir and hclgevf_is_csq defined in
hclgevf_cmd.c, but not used, so remove them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
